2AYL8-HP1305Wireless Bluetooth headset

TWStruewirelessBluetoothheadset InstructionManual Product Specifications: Model No: HP1305 Transmission Distance: 10m Frequency Response: 2402-2480MHz Impedance: 32Ω ChargingTime:Lessthan1.5 hours Material:ABS+PP BluetoothVersion:V5.3 OutputPower:5mW SpeakerDriver:13 mm Batteryfor ChargingCase:300mAh Batteryfor Earbuds:30mAh PlayingTime:Approx5 hours Size:48.8X48.8X21.6mm ButtonFunctionIllustration: 1. Poweron/off:Poweris on whenthe earbudis takenout of the chargingcase.And poweris off whenthe earbudis beingput into the chargingcase. 2. Play/Pause:Doubleclick touchbutton(eitherside)underBluetoothconnectionstate. 3. PreviousTrack:Whenusingtwo earbuds,longpressthe touchbuttonon left earbudfor 2s to playbackthe previoustrack;whileusingone earphone,longpressthe touchbuttonon left earphonefor 2s for the next track. 4. Answera phonecall: Doubleclick touchbutton(eitherside)whenthereis an incomingcall. 5. End a call: Doubleclick touchbutton(eitherside)duringthe phonecommunication. 6. Rejecta call: Presstouchbuttonfor 1s(eitherside)whenthereis an incomingcall. 7. Nexttrack:whenusingtwo earphones,longpressthe touchbuttonon rightearbudfor 2s to play the nexttrack;whileusingone earphone,long pressthe touchbuttonon rightearbudfor 2s to go to the next track. 8. Voiceassistant:Threetimesclick touchbutton(eitherside)to activatethe voiceassistant.Click the touchbuttonthreetimesagainto exit the voiceassistant. Charging: 1. ConnecttheType-Ccableto thechargingadapterandconnecttheotherconnectorof thetype-Cto thechargingbin.Whenthechargingadapteris insertedintothesocket,the adapterwillautomaticallychargetheheadphonecompartment.Theindicatorlightin the headphonecompartmentchargingis redflashing,andtheheadphonecompartment chargingis completed 2. Earphonesareautomaticallychargedwhenputintothewarehouse.Thebluelightof theindicatorlightin thewarehousewillbeonlongwhilecharging,andthebluelightwill gooutwhentheearphonesarecharged. FCC Statement: This devicecomplieswithPart 15 of the FCC Rules.Operationis subjectto the followingtwo conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B Digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Shenzhen Kingree Intelligent Digital Co., Ltd 2022-11-07 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize DongGuan Anci Electronic Technology Co., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Hui Ji Manager Floor3, Bohua Technology Park, Shangkeng Community, Guanhu Street, Longhua New District, ShengZhen, Guangdong, China

Shenzhen Kingree Intelligent Digital Co., Ltd 2022-11-07 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (EUT Name: Wireless Bluetooth headset /Model: HP1305 /FCC ID: 2AYL8-HP1305) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (Block Diagram ,Operational Description,Schematics) required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Hui Ji Manager Floor3, Bohua Technology Park, Shangkeng Community, Guanhu Street, Longhua New District, ShengZhen, Guangdong, China

Label Label Location

ANT

2.4GHz 3216 Chip Antenna: RANT3216F245C01 _ Application: WLAN, 802.11b/g, Bluetooth, WLAN, etc... Features SMD, high reliability, ultra Impact, Omni-directional... Part number Information RANT3216F245C01 (A)(B)(C)(D)(E)(F) Electrical Specification The specification is defined on EVB. Dimension and Terminal Configuration No.Terminal Name 1Feeding/GNG 2GND/Feeding (A)Product TypeChip Antenna (B) Size Code 3.2x1.6mm( ± 0.2mm) (C) MaterialHigh K material (D) Frequency2.4 ~ 2.5GHz (E) Feeding modePIFA & Single Feeding (F) Antenna typeType=01 Working Frequency Range2400 ~2500 MHz Bandwidth120 MHz (Min.) Peak Gain1.15 dBi (Typ.) Impedance50 Ohm Return loss10 dB ( Min) PolarizationLinear Azimuth BeamwidthOmni-directional Operation Temperature(°C)-40 ~85°C Resistance to Soldering Heats 10sec. ( @ 280°C) TerminationNi / Au (Leadless) Dimension (mm) L 3.20±0.20 W 1.60±0.20 T 0.45±0.20 咏成國際科技有限公司電話 :13530576606 RAIN International Technology Co., Ltd. TEL: 13530576606 2.4GHz 3216 Chip Antenna: RANT3216F245C01 _ 1 Evaluation BoardReference PCB DimensionAntenna Layout Reference Unit :mm Electrical Characteristics Return Loss & Radiation Return Loss Frequency(MHz) S11 (dB) 2400-10.50 2450-30.62 2500-11.47 Radiation 2400MHz2450MHz2500MHz Efficiency82.52%85.26%83.01% Peak Gain1.15 dBi1.24 dBi1.19 dBi Directivity1.89 dBi1.97 dBi1.91 dBi X Y Z 2400MHz 2450MHz 2500MHz 2.4GHz 3216 Chip Antenna: RANT3216F245C01 _ Taping Specifications Reel and Taping Specification Reel Specification TYPESIZEABCD 32167”5K/Reel 9.0±0.5 60±213.5±0.5178±2 Tapping Specification PackagingTypeABWEFGHTψDP Paper Type3216 1.90±0.203.50±0.208.0±0.201.75±0.103.5±0.054.0±0.102.0±0.050.75±0.10 1.50±0.10 4.0±0.1 2.4GHz 3216 Chip Antenna: RANT3216F245C01 _ Reliability Table Test ItemProcedure Requirements Ceramic Type Remark (Reference) Electrical Characterization Fulfill the electrical specification User Spec. Thermal Shock 1. Preconditioning: 50 ± 10°C/ 1 hr , then keep for 24 ± 1 hrs at room temp. 2. Initial measure: Spec: refer Initialspec. 3. Rapid change of temperature test: -30°Cto +85°C; 100 cycles; 15 minutes at Lower category temperature; 15 minutes at Upper category temperature. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 107 Temperature Cycling 1. Initial measure: Spec: refer Initialspec. 2. 100 Cycles (-30°Cto +85°C), Soak Mode=1 (2 Cycle/hours). 3. Measurement at 24 ± 2Hours after testcondition. No Visible Damage. Fulfill the electrical specification. JESD22 JA104 High Temperature Exposure 1. Initial measure: Spec: refer Initialspec. 2. Unpowered; 500hours @ T=+85°C. 3. Measurement at 24 ± 2 hours aftertest. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 108 Low Temperature Storage 1. Initial measure: Spec: refer Initialspec. 2. Unpowered: 500hours @ T=-30°C. 3. Measurement at 24 ± 2 hours aftertest. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 108 Solderability (SMD Bottom Side) Dipping method: a. Temperature: 235 ±5°C b. Dipping time: 3 ±0.5s The solder should cover over 95% of the critical area of bottom side. IEC 60384-21/22 4.10 Soldering Heat Resistance (RSH) Preheating temperature: 150 ± 10°C. Preheating time: 1~2 min. Solder temperature: 260 ± 5°C. Dipping time: 5 ± 0.5s No Visible Damage.IEC 60384-21/22 4.10 Vibration5g's for 20 min., 12 cycles each of 3 orientations Note: Use 8"X5" PCB .031" thick 7 secure points on, one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10-2000 Hz. No Visible Damage.MIL-STD-202 Method 204 Mechanical Shock Three shocks in each direction shall be applied along the three mutually perpendicular axes of the test specimen (18 shocks) Peak value: 1,500g’s Duration: 0.5ms Velocity change: 15.4 ft/s Waveform: Half-sine No Visible Damage.MIL-STD-202 Method 213 Humidity Bias 1. Humidity: 85% R.H., Temperature:85 ± 2 °C. 2. Time: 500 ± 24hours. 3. Measurement at 24 ± 2hrs after testcondition. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 Method 106 2.4GHz 3216 Chip Antenna: RANT3216F245C01 _ Board Flex (SMD) 1. Mounting method: IR-Reflow. PCB Size (L:100 × W:40 × T:1.6mm) 2. Apply the load in direction of the arrow until bending reaches 2 mm. No Visible Damage.AEC-Q200 005 AdhesionForce of 1.8Kg for 60 seconds.No Visible Damage Magnification of 20X or greater may be employed for inspection of the mechanical integrity of the device body terminals and body/terminal junction. AEC-Q200 006 Physical Dimension Any applicable method using x10 magnification, micrometers, calipers, gauges, contour projectors, or other measuring equipment, capable of determining the actual specimen dimensions. In accordance with specification. JESD22 JB100 Revision History RevisionDateContent 12019/03/01New Datasheet 22020/02/22Add 2D radiation characteristic

RF EXPOSURE EVALUATION EUT Specification EUT Wireless Bluetooth headset Model Number HP1305 FCC ID 2AYL8-HP1305 Antenna gain (Max) 1.15dBi Operation Frequency 2402-2480MHz Input Rating DC 5V, 0.5A Classification Per Stipulated Test Standard §15.247(i), §2.1093 Kind of Device: Bluetooth Ver. 5.3 Modulation GFSK, π/4-DQPSK Max. output power -4.73dBm(0.0003W) Test Requirement: According to §15.247(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Routine SAR evaluation refers to that specifically required by §2.1093, using measurements or computer simulation. When routine SAR evaluation is not required, portable transmitters with output power greater than the applicable low threshold require SAR evaluation to quality for TCB approval. One antenna is available for the EUT. The minimum separation distance is 5mm. BT DSS: According to KDB 447498, no stand-alone required for BT antenna, and no simultaneous SAR measurement is required. Signature: Tiger Xu Date: 2022-10-22 Transmit Frequency (MHz) Mode Measured Power (dBm) Tune up Power (dBm) Max tune up power(dBm) Calculation Result 1-g SAR 2402 GFSK -7.47 -7±1 -6 0.077860 3 2441 GFSK -6.04 -6±1 -5 0.098813 3 2480 GFSK -5.11 -5±1 -4 0.125388 3 2402 Π/4-DQ PSK -6.97 -7±1 -6 0.077860 3 2441 Π/4-DQ PSK -5.27 -5±1 -4 0.124398 3 2480 Π/4-DQ PSK -4.73 -5±1 -4 0.125388 3

TRF No.: 01-R005-3A TRF Originator: GTG TRF Date: 2022-06-29 Web: www.gtggroup.com E-mail: [email protected] Tel.: 86-400 755 8988 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Wireless Bluetooth headset Model No.: HP1305 Trademark: N/A FCC ID: 2AYL8-HP1305 Report No.: E01A22090017F00601 Issue Date: October 13, 2022 Prepared for Shenzhen Kingree Intelligent Digital Co., Ltd Floor3, Bohua Technology Park, Shangkeng Community, Guanhu Street, Longhua New District, ShengZhen, Guangdong, China Prepared by Dong Guan Anci Electronic Technology Co., Ltd. 1-2 Floor, Building A, No.11, Headquarters 2 Road, Songshan, Lake Hi-tech Industrial Development Zone, Dongguan City, Guangdong Pr., China. This report shall not be reproduced, except in full, without the written approval of Dong Guan Anci Electronic Technology Co., Ltd. Page 1 of 70 Report No.: E01A22090017F00601 TRF No.: 01-R005-3A Global Testing , Great Quality. VERIFICATION OF COMPLIANCE Applicant: Shenzhen Kingree Intelligent Digital Co., Ltd Floor3, Bohua Technology Park, Shangkeng Community, Guanhu Street, Longhua New District, ShengZhen, Guangdong, China Manufacturer: Shenzhen Kingree Intelligent Digital Co., Ltd Floor3, Bohua Technology Park, Shangkeng Community, Guanhu Street, Longhua New District, ShengZhen, Guangdong, China Product Description: Wireless Bluetooth headset Trade Mark: N/A Model Number: HP1305 We hereby certify that: The above equipment was tested by Dong Guan Anci Electronic Technology Co., Ltd.The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10-2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247(2020). Date of Test : September 18, 2022 to September 26, 2022 Prepared by : Duke Liu /Supervisor Reviewer & Authorized Signer : Tiger Xu / Director Page 2 of 70 Report No.: E01A22090017F00601 TRF No.: 01-R005-3A Global Testing , Great Quality. Modified Information Version Summary Revision Date Report No. Ver.1.0 Original Report / E01A22090017F00601 Page 3 of 70 Report No.: E01A22090017F00601 TRF No.: 01-R005-3A Global Testing , Great Quality. Table of Contents 1. GENERAL INFORMATION ......................................................................................................... 5 1.1 PRODUCT DESCRIPTION ............................................................................................................................. 5 1.2 TEST METHODOLOGY ................................................................................................................................. 5 1.3 TEST FACILITY ............................................................................................................................................. 6 2. SYSTEM TEST CONFIGURATION............................................................................................... 7 2.1EUT CONFIGURATION ................................................................................................................................. 7 2.2 EUT EXERCISE..................................................................................................................................... 7 2.3 TEST PROCEDURE..................................................................................................................................... 7 2.4CONFIGURATION OF TESTED SYSTEM ........................................................................................................ 8 3. SUMMARY OF TEST RESULTS ................................................................................................... 9 4. DESCRIPTION OF TEST MODES .............................................................................................. 10 5. TEST SYSTEM UNCERTAINTY .................................................................................................. 11 6. CONDUCTED EMISSIONS TEST ............................................................................................... 12 6.1MEASUREMENT PROCEDURE: ................................................................................................................... 12 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ......................................................................... 12 6.3MEASUREMENT EQUIPMENT USED: .......................................................................................................... 12 6.4 MEASUREMENT RESULT: .......................................................................................................................... 12 CONDUCTED MEASUREMENT PHOTOS: ......................................................................................................... 14 6.5 CONDUCTED MEASUREMENT PHOTOS: ................................................................................................... 15 7. RADIATED EMISSION TEST ....................................................................................................... 16 7.1MEASUREMENT PROCEDURE .................................................................................................................... 16 7.2TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .......................................................................... 18 7.3 MEASUREMENT EQUIPMENT USED: ......................................................................................................... 19 7..4 RADIATED EMISSION LIMIT ...................................................................................................................... 20 7.5 MEASUREMENT RESULT ......................................................................................................................... 21 7.5 RADIATED MEASUREMENT PHOTOS: ...........................................................................................…

Text truncated - open the document above for the full version.