Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Luxottica Group S.p.A One Icon, Foothill Ranch, California, United States 92610 Tel: 949-9813308 Fax: 949-672-6874 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) To whom it may concern, [Luxottica Group S.p.A Grantee Code 2AYOA] (“the applicant”) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC Grantee Code. The service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. The applicant acknowledges that they will maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the following agent information changes. Company Name: Luxottica Group S.p.A Company US Address: One Icon, Foothill Ranch, California, United States 92610 Contact Person: Jane Wang Email: [email protected] Telephone number: 949-9813308 FRN: 0029716974 Sincerely yours, Signed by the Applicant Name: Jane Wang Title: Director Email: [email protected] Date: June 12, 2025
Luxottica Group S.p.A One Icon, Foothill Ranch, California, United States 92610 TEL: 949-9813308, FAX: 949-672-6874 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: August 17, 2026 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) FCC ID: 2AYOA-4012 To whom it may concern, Luxottica Group S.p.A (“the applicant”) certifies that the equipment for which authorization is sought is not the equipment on the Covered List, as established pursuant to § 1.50002 of CFR Title 47, that is prohibited from obtaining an equipment authorization under this subpart. This includes equipment that: (1) Has been certified as a modular transmitter; or (2) Meets the modular transmitter requirements of § 15.212 of this chapter and could be certified as a modular transmitter. pursuant to section 2.903 resulting the recent adoption of FCC 25-71 (et al., ET Docket No. 21-232, Second Report and Order); or (3) Uncrewed aircraft systems (UAS) and UAS critical components produced in a foreign country and all communications and video surveillance equipment and services listed in Section 1709(a)(1) of the FY25 National Defense Authorization Act (Pub. L. 118-159) Applicant certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Applicant further certifies that no Cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software is installed in the equipment being certified. The above-referenced Covered List is published by the Public Safety and Homeland Security Bureau (PSHSB), pursuant to Section 1.50002 of the Commission’s rules. Sincerely, ________________________ Jane Wang Director [email protected]
Luxottica Group S.p.A One Icon, Foothill Ranch, California, United States 92610 TEL: 949-9813308, FAX: 949-672-6874 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: August 17, 2026 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) FCC ID: 2AYOA-4012 To whom it may concern, Luxottica Group S.p.A (“the applicant”) certifies that the equipment for which authorization is sought is not the equipment on the Covered List, as established pursuant to § 1.50002 of CFR Title 47, that is prohibited from obtaining an equipment authorization under this subpart. This includes equipment that: (1) Has been certified as a modular transmitter; or (2) Meets the modular transmitter requirements of § 15.212 of this chapter and could be certified as a modular transmitter. pursuant to section 2.903 resulting the recent adoption of FCC 25-71 (et al., ET Docket No. 21-232, Second Report and Order); or (3) Uncrewed aircraft systems (UAS) and UAS critical components produced in a foreign country and all communications and video surveillance equipment and services listed in Section 1709(a)(1) of the FY25 National Defense Authorization Act (Pub. L. 118-159) Applicant certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Applicant further certifies that no Cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software is installed in the equipment being certified. The above-referenced Covered List is published by the Public Safety and Homeland Security Bureau (PSHSB), pursuant to Section 1.50002 of the Commission’s rules. Sincerely, ________________________ Jane Wang Director [email protected]
Luxottica Group S.p.A One Icon, Foothill Ranch, California, United States 92610 TEL: 949-9813308, FAX: 949-672-6874 Date: August 17, 2026 FCC Laboratory 7435 Oakland Mills Rd Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AYOA-4012 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following documents from public disclosure indefinitely. ⚫ Schematic Diagram ⚫ Block Diagram ⚫ Part List ⚫ Operational Description ⚫ Tune-up Procedure Above mentioned documents which contain detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we are requesting the Commission to withhold the following documents for 180 days after the grant of equipment authorization is issued: ⚫ External Photos ⚫ Internal Photos ⚫ Test Setup Photos ⚫ User Manual It is our understanding that all measurement test reports, FCC ID label format cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, _______________________ Jane Wang Director [email protected]
Luxottica Group S.p.A One Icon, Foothill Ranch, California, United States 92610 TEL: 949-9813308, FAX: 949-672-6874 Date: August 17, 2026 FCC Agent Authorization Luxottica Group S.p.A hereby authorize Sporton International Inc. to act on our behalf in all matters relating to applications for FCC equipment authorization, including the signing of all documents relating to these matters. Any and all acts carried out by Sporton International Inc. on our behalf shall have the same effect as acts of our own. We also hereby certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits that includes FCC benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988. 21 U.S.C. 862. This authorization is limited to the product of as following: FCC ID: 2AYOA-4012 This authorization is valid until further written notice from Luxottica Group S.p.A. Sincerely, ________________________ Jane Wang Director [email protected]
Label is in the inner side of temple FCCID2AYOA-4012RW7004 IC26243-4012 Label sample:
Label is in the inner side of temple FCCID2AYOA-4012RW7004V IC26243-4012 Label sample:
Label is in the inner side of temple FCCID2AYOA-4012RW7005 IC26243-4012 Label sample:
Label is in the inner side of temple FCCID2AYOA-4012RW7005V IC26243-4012 Label sample:
TEL: 886-3-327-3456 Page 1 of 26 FAX: 886-3-328-4978 Issued Date : Aug. 25, 2026 Template version: 260717 FCC SAR TEST REPORT Report No. : FA652603 FCC SAR TEST REPORT FCC ID : 2AYOA-4012 Equipment : AI GLASSES Brand Name : Ray-Ban Meta or Ray-Ban Model Name : RW7004, RW7004V, RW7005, RW7005V Applicant : Luxottica Group S.p.A. Piazzale Cadorna 3 20123 Milan, Italy Manufacturer : Luxottica Group S.p.A. Piazzale Cadorna 3 20123 Milan, Italy Standard : FCC 47 CFR Part 2 (2.1093) The product was received on Jul. 08, 2026 and testing was started from Jul. 24, 2026 and completed on Aug. 07, 2026. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample provide by manufacturer and the test data has been evaluated in accordance with the test procedures given in 47 CFR Part 2.1093 and FCC KDB and has been pass the FCC requirement. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Laboratory, the test report shall not be reproduced except in full. Sporton International Inc. Wensan Laboratory No.58, Aly. 75, Ln. 564, Wenhua 3rd, Rd., Guishan Dist., Taoyuan City 333010, Taiwan Approved by: Cona Huang / Deputy Manager TEL: 886-3-327-3456 Page 2 of 26 FAX: 886-3-328-4978 Issued Date : Aug. 25, 2026 Template version: 260717 FCC SAR TEST REPORT Report No. : FA652603 Table of Contents 1. Statement of Compliance ............................................................................................................................................. 4 2. Guidance Applied .......................................................................................................................................................... 4 3. Equipment Under Test (EUT) Information ................................................................................................................... 5 3.1 General Information ............................................................................................................................................... 5 4. RF Exposure Limits....................................................................................................................................................... 6 4.1 Uncontrolled Environment ...................................................................................................................................... 6 4.2 Controlled Environment .......................................................................................................................................... 6 5. Specific Absorption Rate (SAR) ................................................................................................................................... 7 5.1 Introduction ............................................................................................................................................................ 7 5.2 SAR Definition ........................................................................................................................................................ 7 6. System Description and Setup .................................................................................................................................... 8 6.1 Test Site Location ................................................................................................................................................... 8 6.2 E-Field Probe ......................................................................................................................................................... 9 6.3 Data Acquisition Electronics (DAE) ........................................................................................................................ 9 6.4 Phantom ................................................................................................................................................................10 6.5 Device Holder........................................................................................................................................................12 7. Measurement Procedures ...........................................................................................................................................13 7.1 Spatial Peak SAR Evaluation ................................................................................................................................13 7.2 Power Reference Measurement............................................................................................................................14 7.3 Area Scan .............................................................................................................................................................14 7.4 Zoom Scan ............................................................................................................................................................15 7.5 Volume Scan Procedures ......................................................................................................................................15 7.6 Power Drift Monitoring ...........................................................................................................................................15 8. Test Equipment List .....................................................................................................................................................16 9. System Verification ......................................................................................................................................................17 9.1 Tissue Verification .................................................................................................................................................17 9.2 System Performance Check Results .....................................................................................................................18 10. Bluetooth Output Power (U…
Text truncated - open the document above for the full version.
Scans Setup FastVolume ScanZoom Scan Grid Extents [mm]130.0 x 90.030.0 x 30.0 x 30.0 Grid Steps [mm]10.0 x 10.05.0 x 5.0 x 1.5 Sensor Surface [mm]3.03.0 Graded GridN/AYes Grading RatioN/A1.5 Measurement Software16.4.0.5005 Scan MethodMeasuredMeasured Measurement Results FastVolume ScanZoom Scan Date2026-07-242026-07-24 psSAR1g [W/Kg]14.415.0 psSAR10g [W/Kg]5.966.61 Power Drift [dB]-0.130.04 TSL CorrectionPositive onlyPositive only M2/M1 [%]83.3 Dist 3dB Peak [mm]8.6 System Check_Head_2450MHz Device Under Test Properties ModelDimensions [mm]DUT Type Device10.0 x 10.0 x 10.0Other Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] BandGroup, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Headstand, HSLDEFAULT, 0.00D2450CW, 0--2450.000, 507.281.8542.6 Hardware Setup PhantomTSL, Measured DateProbe, Calibration DateDAE, Calibration Date SAM-HeadStand V10.0 - 0717HSL_600-7200_260724, 2026-07-24EX3DV4 - SN7590, 2026-03-17DAE4 Sn1805, 2026-05-19 SAR Pattern Scans Setup FastVolume ScanZoom Scan Grid Extents [mm]140.0 x 130.030.0 x 30.0 x 30.0 Grid Steps [mm]10.0 x 10.05.0 x 5.0 x 1.5 Sensor Surface [mm]3.03.0 Graded GridN/AYes Grading RatioN/A1.5 Measurement Software16.4.0.5005 Scan MethodMeasuredMeasured Measurement Results FastVolume ScanZoom Scan Date2026-07-242026-07-24 psSAR1g [W/Kg]7.939.39 psSAR10g [W/Kg]3.634.44 Power Drift [dB]0.080.11 TSL CorrectionPositive onlyPositive only M2/M1 [%]82.9 Dist 3dB Peak [mm]10.3 System Check_Head_2450MHz Device Under Test Properties ModelDimensions [mm]DUT Type Device10.0 x 10.0 x 10.0Other Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] BandGroup, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Headstand, HSLDEFAULT, 0.00D2450CW, 0--2450.000, 507.281.8542.6 Hardware Setup PhantomTSL, Measured DateProbe, Calibration DateDAE, Calibration Date SAM-HeadStand V10.0 - 0717HSL_600-7200_260724, 2026-07-24EX3DV4 - SN7590, 2026-03-17DAE4 Sn1805, 2026-05-19 SAR Pattern Date: 2026-07-24 System Check_Head_2450MHz DUT: D2450V2 - SN929 Communication System: CW; Frequency: 2450.000 MHz Medium: HSL_600-7200_260724 Medium parameters used: f= 2450.000 MHz; σ= 1.85 S/m; ε r = 42.6 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7590; ConvF(7.28, 7.08, 7.07); Calibrated: 2026-03-17 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1805; Calibrated: 2026-05-19 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.4.0.5005 - UID: CW, 0-- Pin=24.0dBm/Area Scan (40.0 mm x 80.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 13.3 W/kg; SAR (10g) = 6.22 W/kg; TSL Correction: Positive only Pin=24.0dBm/Zoom Scan (30.0 mm x 30.0 mm x 31.2 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = -0.00 dB SAR (1g) = 13.3 W/kg; SAR (8g) = 6.89 W/kg; SAR (10g) = 6.25 W/kg Smallest distance from peaks to all points 3 dB below = 9.0 mm Ratio of SAR at M2 to SAR at M1 = 80.9 % TSL Correction: Positive only Date: 2026-08-07 System Check_Head_2450MHz DUT: D2450V2 - SN929 Communication System: CW; Frequency: 2450.000 MHz Medium: HSL_600-7200_260807 Medium parameters used: f= 2450.000 MHz; σ= 1.84 S/m; ε r = 41.0 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7590; ConvF(7.28, 7.08, 7.07); Calibrated: 2026-03-17 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1805; Calibrated: 2026-05-19 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.4.0.5005 - UID: CW, 0-- Pin=24.0dBm/Area Scan (40.0 mm x 80.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 13.1 W/kg; SAR (10g) = 6.12 W/kg; TSL Correction: Positive only Pin=24.0dBm/Zoom Scan (30.0 mm x 30.0 mm x 31.2 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = 0.02 dB SAR (1g) = 13.2 W/kg; SAR (8g) = 6.83 W/kg; SAR (10g) = 6.20 W/kg Smallest distance from peaks to all points 3 dB below = 9.0 mm Ratio of SAR at M2 to SAR at M1 = 81.1 % TSL Correction: Positive only
Scans Setup FastVolume ScanZoom Scan Grid Extents [mm]180.0 x 140.030.0 x 30.0 x 30.0 Grid Steps [mm]10.0 x 10.05.0 x 5.0 x 1.5 Sensor Surface [mm]3.03.0 Graded GridN/AYes Grading RatioN/A1.5 Measurement Software16.4.0.5005 Scan MethodMeasuredMeasured Measurement Results FastVolume ScanZoom Scan Date2026-07-242026-07-24 psSAR1g [W/Kg]0.3200.017 psSAR10g [W/Kg]0.1130.007 Power Drift [dB]0.09-0.09 TSL CorrectionPositive onlyPositive only M2/M1 [%]81.0 Dist 3dB Peak [mm]7.1 #01_Bluetooth_1Mbps_Face-worn_0mm_Ch0 Device Under Test Properties ModelDimensions [mm]DUT Type Device190.0 x 150.0 x 50.0Other Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] BandGroup, UIDFrequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Headstand, HSL DEFAULT, 0.00ISM 2.4 GHz Band Bluetooth, 10032-CAA 2402.000, 07.2842.7 Hardware Setup PhantomTSL, Measured DateProbe, Calibration DateDAE, Calibration Date SAM-HeadStand V10.0 - 0717HSL_600-7200_260724, 2026-07-24EX3DV4 - SN7590, 2026-03-17DAE4 Sn1805, 2026-05-19 SAR Pattern 1.82 Communication System: IEEE 802.15.1 Bluetooth; Frequency: 2402.000 MHz Medium: HSL_600-7200_260724 Medium parameters used: f= 2402.000 MHz; σ= 1.82 S/m; ε r = 42.7 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7590; ConvF(7.28, 7.08, 7.07); Calibrated: 2026-03-17 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1805; Calibrated: 2026-05-19 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.4.0.5005 - UID: Bluetooth, 10032-CAA Area Scan (120.0 mm x 260.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.260 W/kg; SAR (10g) = 0.097 W/kg; TSL Correction: Positive only Zoom Scan (30.0 mm x 30.0 mm x 31.2 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = -0.04 dB SAR (1g) = 0.303 W/kg; SAR (8g) = 0.108 W/kg; SAR (10g) = 0.095 W/kg Smallest distance from peaks to all points 3 dB below = 4.0 mm Ratio of SAR at M2 to SAR at M1 = 50.8 % TSL Correction: Positive only Date: 2026-07-24 #02_Bluetooth_1Mbps_Back_0mm_Ch0 Communication System: IEEE 802.15.1 Bluetooth; Frequency: 2402.000 MHz Medium: HSL_600-7200_260807 Medium parameters used: f= 2402.000 MHz; σ= 1.81 S/m; ε r = 41.0 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7590; ConvF(7.28, 7.08, 7.07); Calibrated: 2026-03-17 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1805; Calibrated: 2026-05-19 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.4.0.5005 - UID: Bluetooth, 10032-CAA Area Scan (100.0 mm x 200.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0 W/kg; SAR (10g) = 0 W/kg; TSL Correction: Positive only Date: 2026-08-07 #03_Bluetooth_1Mbps_Front Edge_0mm_Ch0
TEL : 886-3-327-0868 Page Number : 1 of 27 FAX : 886-3-327-0855 Issue Date : Aug. 20, 2026 Report Template No.: BU5-TRLP0002BT Version 2.11 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR652603A FCC RADIO TEST REPORT FCC ID : 2AYOA-4012 Equipment : AI GLASSES Brand Name : Ray-Ban Meta or Ray-Ban Model Name : RW7004, RW7004V, RW7005, RW7005V Applicant : Luxottica Group S.p.A. Piazzale Cadorna 3 20123 Milan, Italy Manufacturer : Luxottica Group S.p.A. Piazzale Cadorna 3 20123 Milan, Italy Standard : FCC Part 15 Subpart C §15.247 The product was received on May 26, 2026 and testing was performed from Jul. 06, 2026 to Aug. 15, 2026. We, Sporton International Inc. Wensan Laboratory, would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval from Sporton International Inc. Wensan Laboratory, the test report shall not be reproduced except in full. Approved by: Louis Wu Sporton International Inc. Wensan Laboratory No.58, Aly. 75, Ln. 564, Wenhua 3rd, Rd., Guishan Dist., Taoyuan City 333010, Taiwan (R.O.C.) TEL : 886-3-327-0868 Page Number : 2 of 27 FAX : 886-3-327-0855 Issue Date : Aug. 20, 2026 Report Template No.: BU5-TRLP0002BT Version 2.11 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR652603A Table of Contents 1 General Description ................................................................................................................................... 5 1.1 Product Feature of Equipment Under Test ........................................................................................ 5 1.2 Modification of EUT ........................................................................................................................... 5 1.3 Testing Location ................................................................................................................................ 6 1.4 Applicable Standards ......................................................................................................................... 6 2 Test Configuration of Equipment Under Test ......................................................................................... 7 2.1 Carrier Frequency Channel ............................................................................................................... 7 2.2 Test Mode .......................................................................................................................................... 8 2.3 Connection Diagram of Test System ................................................................................................. 9 2.4 Support Unit used in test configuration and system .......................................................................... 9 2.5 EUT Operation Test Setup .............................................................................................................. 10 2.6 Measurement Results Explanation Example ................................................................................... 10 3 Test Result ................................................................................................................................................ 11 3.1 Number of Channel Measurement .................................................................................................. 11 3.2 Hopping Channel Separation Measurement ................................................................................... 12 3.3 Dwell Time Measurement ................................................................................................................ 13 3.4 20dB and 99% Bandwidth Measurement ........................................................................................ 14 3.5 Output Power Measurement ............................................................................................................ 15 3.6 Conducted Band Edges Measurement............................................................................................ 16 3.7 Conducted Spurious Emission Measurement ................................................................................. 17 3.8 Radiated Band Edges and Spurious Emission Measurement ........................................................ 18 3.9 AC Conducted Emission Measurement........................................................................................... 22 3.10 Antenna Requirements .................................................................................................................... 24 4 List of Measuring Equipment ................................................................................................................. 25 5 Measurement Uncertainty ....................................................................................................................... 27 Appendix A. Conducted Test Results Appendix B. AC Conducted Emission Test Result Appendix C. Radiated Spurious Emission Test Result Appendix D. Duty Cycle Plots Appendix E. Setup Photographs TEL : 886-3-327-0868 Page Number : 3 of 27 FAX : 886-3-327-0855 Issue Date : Aug. 20, 2026 Report Template No.: BU5-TRLP0002BT Version 2.11 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR652603A History of this test report Report No. Version Description Issue Date FR652603A 01 Initial issue of report Aug. 20, 2026 TEL : 886-3-327-0868 Page Number : 4 of 27 FAX : 886-3-327-0855 Issue Date : Aug. 20, 2026 Report Template No.: BU5-TRLP0002BT Version 2.11 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR652603A Summary of Test Result Report Clause Ref Std. Clause Test Items Result (PASS/FAIL) Remark 3.1 15.247(a)(1) Number of Channels Pass - 3.2 15.247(a)(1) Hopping Channel Separation Pass - 3.3 15.247(a)(1) Dwell Time of Each Channel Pass - 3.4 15.247(a)(1) 20dB Bandwidth Pass - 3.4 2.1049 99% Occupie…
Text truncated - open the document above for the full version.
Antenna Gain Test Report Test Date: 4/29/26-6/24/26 Meta Platforms Technologies, LLC Approved by: Daniel Tu Table of Contents 1. General Information 2 2. Chamber information 2 3. Commercial Test Software 2 4. Test Equipment 3 5. Antenna Test Method 3 6. Antenna Gain Results and Plots 3 7. Antenna Photo 3 1 Meta Platforms Technologies, LLC 1. General Information The purpose of this report is to demonstrate compliance to the FCC Part 15 Antenna requirement. 2. Chamber information Multi-probe fully anechoic OTA chamber, MVG system model: SG64. Chamber pathloss calibration is per CTIA test plan v3.9.5 Section 4 Range Reference Requirements. Chamber Location: Meta Lab at Fremont 6422 3. Commercial Test Software Test software is from MVG, Wave Studio v2024.2.8 2 Meta Platforms Technologies, LLC 4. Test Equipment Equipment Calibration Due Date MVG Multi-probe Fully anechoic OTA Chamber March 3, 2027 CMW 500 August 8, 2026 Note: OTA Chamber was audited routinely to ensure accurate results and a 2 year calibration cycle. 5. Antenna Test Method Measurement parameters follow Meta’s validated active OTA antenna measurement procedure. Measurements were performed in an MVG SG64 multi-probe fully anechoic chamber using a full-sphere 3D pattern measurement. Active antenna measurement Steps: 1) DUT placed in free-space inside an anechoic chamber. 2) DUT establishes a connection with a communication call box. 3) EIRP are measured with maximum 15 degree step size at each probe position 0 degree – 360 degrees with respect to the turntable position from 0-180 degrees for a full 3D pattern measurement. 4) Data and all pathloss will be processed by MVG Wave Studio. 5) Peak EIRP – Conducted power = Peak Antenna gain. 6) Repeat Step 2 to 5 for each testing channel/frequency. 6. Antenna Gain Results and Plots Refer to Exhibit A for antenna gain results and plots. 7. Antenna Photo Refer to Exhibit B for Antenna information and photo. 3 Meta Platforms Technologies, LLC Exhibit A - Gain Results and Plots Antenna 2D Total Gain Plots (Phi cut with peak gain): BT 2.4GHz 4 Meta Platforms Technologies, LLC
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.40 GHz - 2.48 GHz | 10.00 mW |
Nuance Audio Remote Plus
Equipment Class
DTS - Digital Transmission SystemAI GLASSES
Equipment Class
6XD - 15E 6 GHz Low Power Indoor ClientAI GLASSES
Equipment Class
6XD - 15E 6 GHz Low Power Indoor Client