2AYT3-AC180PPortable Power Station

英文说明书（美规BLUETTI） AC180P PLP008B-6d01A1 杨振华 23.07.03 杨振华 23.05.19 杨振华 23.07.03更新内容 A1 A2 17.0303.0611-01 技术要求 成品尺寸：A5（143X210mm） 材质：封面封底内页80g书写纸，订装 颜色：单黑印刷 32P AC180P Portable Power Station User Manual Please read this manual carefully before use and keep it for future reference. Warning 1. Charge the unit before first use. 2. Do not use solar panels with open circuit voltage higher than 60V. Solar input voltage range for the unit is DC 12V~60V. 3. Charge the unit when the SoC drops below 5%. If the SoC drops to 0, power off the unit and charge it for at least 30mins before restarting. 4. The unit is for off-grid use only. Do not connect its AC output to the grid. 5. If not used for more than 3 months, charge the unit to 40%~60% SoC and store it with the power off. For optimum battery life, discharge and charge the unit every 3 months. Thank You! Thank you for making BLUETTI a part of your family. From the very beginning, BLUETTI has tried to stay true to a sustainable future through green energy storage solutions for both indoor and outdoor use while delivering an exceptional eco-f riendly experience for our homes and our world. That's why BLUETTI makes its presence in 70+ countries and is trusted by millions of customers across the globe. Franch Germany Netherlands Safety Instructions General Safety Handling Storage and Usage What’s In The Box Product Overview Diagram Specifications Operating Instructions Buttons LCD Screen Charging Discharging BLUETTI App Appendix FAQs Troubleshooting Abbreviations FCC Warning Important Instructions Contents 1 1.1 1.2 1.3 2 3 3.1 3.2 4 4.1 4.2 4.3 4.4 4.5 5 5.1 5.2 5.3 5.4 5.5 05 05 07 07 08 10 10 11 12 12 14 15 17 18 19 19 20 21 21 23 1. Safety Instructions Read this manual for instructions on the proper use and safety information for the unit. Follow the warnings and instructions marked on the unit and its accessories. Pay attention to the "Instruction", "Caution", "Warning" and "Danger" symbols in this manual, and follow the instructions carefully to avoid injury or damage. The Safety Requirements provided herein are for illustrative purposes that include but are not limited to those listed in this manual. Actual operation shall comply with all applicable safety standards. If you have any questions, feel f ree to contact BLUETTI support or your local BLUETTI dealers. 1.1. General Safety • Always operate or store the unit in the conditions specified in this manual. • The installation and ambient conditions must comply with the regulations in the relevant international, national or regional standards. • Unauthorized disassembly, alteration of the equipment or modification of the software code is not allowed. BLUETTI shall not be liable for the following circumstances: • Equipment damage caused by force majeure, such as earthquake, fire, storm, flood, mudslide, etc. • Damage or loss during transportation. • Damage caused by storage conditions that do not meet the requirements specified in this manual. • Damage to the hardware or data of the equipment due to customer negligence, improper operation or intentional damage. • Damage to the system caused by a third party or the customer, including handling and installation that does not meet the requirements specified in this manual. • This product is not suitable for providing electrical service for equipment and machines that are highly dependent on the reliability of electrical power supply and that involve personal safety, such as atomic energy, aviation, medical, etc. Poweroak will not be held responsible for any personal safety accidents, fire accidents, equipment failures, etc. caused by using this product to supply power to the above equipment and machines. • Damage caused by adjustment, alteration or removal of identification marks. To avoid danger, please regulate the operation in the following manner • Do not install, use and maintain the unit in adverse weather conditions such as lightning, rain, snow and strong breezes (including but not limited to handling and operating the unit, plugging and unplugging signal connections to outdoor facilities, working at height, outdoor installations, etc.). JUST POWER ON05 • The transportation, wiring and maintenance shall comply with all applicable laws, regulations and standards. • User-provided materials and tools required shall meet the requirements specified in applicable laws, regulations and relevant standards. • Always turn off the power source before starting any electrical work. • Do not clean the unit with water. • Do not disassemble, modify, tamper with or repair the unit on your own. • Regularly inspect the unit and its accessories for damage or deterioration. • Use a tester to check for the presence of dangerous voltage before touching any conductor or terminal. • If the unit’s shell is cracked during transportation or use, do not use it and contact BLUETTI support or your local BLUETTI dealers. • Use a dry powder extinguisher if the unit catches fire. • In case of fire, EVACUATE the building or affected area immediately, activate the closest FIRE ALARM system and CALL 9-1-1 or your local emergency phone number. • Use genuine cables and accessories provided by BLUETTI. • Keep the unit away f rom heat sources or high temperatures, and do not expose it to direct sunlight. • Do not store the unit with flammable liquids, gases, or explosive materials. • Make sure the area where you are using the unit is well ventilated and spacious. • Do not block or cover the vents of the unit as this may cause irreversible damage to it. • Use the unit for its intended purpose and avoid stacking objects on top of it during storage or use. • Do not move the unit during operation as the vibrations and shocks associated with movement may cause damage to the internal hardware. • In case of malfunction, turn off the unit immediately and contact BLUETTI support or your local BLUETTI dealers if this manual cannot adequately explain the malfunction to you. • Do not place t…

Text truncated - open the document above for the full version.

SHENZHEN POWEROAK NEWENER CO., LTD F19, BLD No.1, Kaidaer Tongsha Rd No.168, Xili Street, Nanshan, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 08-25-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AYT3-AC180P Product Name: Portable Power Station Model Name: AC180P [SHENZHEN POWEROAK NEWENER CO., LTD] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Cara Zou)

SHENZHEN POWEROAK NEWENER CO., LTD F19, BLD No.1, Kaidaer Tongsha Rd No.168, Xili Street, Nanshan, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 08-25-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AYT3-AC180P Product Name: Portable Power Station Model Name: AC180P [SHENZHEN POWEROAK NEWENER CO., LTD] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Cara Zou)

SHENZHEN POWEROAK NEWENER CO., LTD F19, BLD No.1, Kaidaer Tongsha Rd No.168, Xili Street, Nanshan, Shenzhen, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Aug. 24, 2023 Subject; Request for Confidentiality FCC ID: 2AYT3-AC180P To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Antenna Specification FCC_Confidential Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Cara Zou Title: Manager

Agent Authorization Company: SHENZHEN POWEROAK NEWENER CO., LTD Address: F19, BLD No.1, Kaidaer Tongsha Rd No.168, Xili Street, Nanshan, Shenzhen, China Product Name: Portable Power Station Model Number(s): AC180P Product Description: Portable Power Station We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Aug. 24, 2023 Name: Cara Zou Title: Manager Company: SHENZHEN POWEROAK NEWENER CO., LTD

Report No.: AGC01741230703AP03 Page 1 of 4 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC01741230703AP03 Page 2 of 4 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC01741230703AP03 Page 3 of 4 LEFT VIEW OF EUT RIGHT VIEW OF EUT Report No.: AGC01741230703AP03 Page 4 of 4 PORT VIEW-1 OF EUT LABEL VIEW OF EUT ****************************************End of Report*************************************

+0/-0.3mm +0/-0.3mm 138mm R5mm 70mm C:0 M:0 Y:0 K:25 Label location map 138*70mm Portable Power Station Model: AC180P Battery Capacity: 1440Wh, 32V 45Ah P/N: 17.0301.0000-00A0MADE IN CHINA Output: AC: 120V 50/60Hz, 1800W/1800VA Max USB-A: 5V 3A, 15W Total x2 USB-C: 5/9/12/15/20V 3A; 20V 5A (With E-Marker chip built in) Wireless Charging: 5/7.5/10/15W Cigarette Lighter Port: 12V 10A AC & DC Output: 1800W Total Discharging Temperature: -20 o C-40 o C Charging Temperature: 0 o C-40 o C Working Humidity: 10%-90% Input: AC: 120V 50/60Hz, 15A Max DC/PV: 12V-60V 10A, 500W Max CAN ICES-003 (B) / NMB-003 (B) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. SHENZHEN POWEROAK NEWENER CO., LTD. Address: F19, BLD No.1, Kaidaer, Tongsha Rd No.168, Xili Street, Nanshan, Shenzhen, China FCC ID:2AYT3-AC180PIC:29079-AC180P

Report No.: AGC01741230703AP03 Page 1 of 8 INTERNAL PHOTOS OPEN VIEW-1 OF EUT INTERNAL VIEW -1 OF EUT Report No.: AGC01741230703AP03 Page 2 of 8 INTERNAL VIEW-2 OF EUT INTERNAL VIEW-3 OF EUT BT Antenna Report No.: AGC01741230703AP03 Page 3 of 8 INTERNAL VIEW-4 OF EUT INTERNAL VIEW-5 OF EUT Report No.: AGC01741230703AP03 Page 4 of 8 INTERNAL VIEW-6 OF EUT INTERNAL VIEW-7 OF EUT Report No.: AGC01741230703AP03 Page 5 of 8 INTERNAL VIEW-8 OF EUT INTERNAL VIEW-9 OF EUT Report No.: AGC01741230703AP03 Page 6 of 8 INTERNAL VIEW-10 OF EUT INTERNAL VIEW-11 OF EUT Report No.: AGC01741230703AP03 Page 7 of 8 INTERNAL VIEW-12 OF EUT INTERNAL VIEW-13 OF EUT WPT Antenna 19cm 43cm Report No.: AGC01741230703AP03 Page 8 of 8 INTERNAL VIEW-14 OF EUT BATTERY VIEW OF EUT ****************************************End of Report*************************************

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION FCC ID 2AYT3-AC180P Product Description Portable Power Station Model Name AC180P Frequency Band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Bluetooth: 2.402GHz ~ 2.480GHz Others (WPT: 110.5KHz-205KHz) Device Category Portable (<20cm separation) Mobile (≥20cm separation) Others: Antenna Diversity BT:PCB Antenna WPT: Coil Antenna Max. Output Power BT: -1.516dBm Field Strength of Fundamental WPT:74.40dBuV/m (Max) at 3m distance Antenna Gain BT: -2.31dBi WPT: 0dBi Minimum Assessment Distance 20cm Evaluation Applied MPE Evaluation SAR Evaluation Evaluation Result Pass 2. PORTABLE DEVICE EVALUATION METHOD AND LIMIT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm) ( f(MHz)/150)] mW, at 100MHz to 1500 MHz; b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)-10] mW at > 1500 MHz and ≤6 GHz; 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by 1/2 for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. 3. MOBILE DEVICE EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. MEASUREMENT RESULT A minimum test separation distance ≥ 20 cm is required between the antenna and radiating structures of the device and nearby persons to apply mobile device exposure limits. The distance must be at least 20 cm and fully supported by the operating and installation configurations of the transmitter and its antenna(s), according to the source-based time-averaged maximum power requirements of § 2.1091(d)(2). In cases where cable losses or other attenuations are applied to determine compliance, the most conservative operating configurations and exposure conditions must be evaluated. BT: Antenna Gain=-2.31dBi (Numeric 0.59), π=3.14 Note: 1. Only the worst case recorded. 2. Max Power (dBm) = Field Strength of Fundamental (dBuV/m@3m)-95.23 3. Max Power (mW) = 10^ (Max power (dBm)/10) 4. The wireless technology multi transmission calculation result is: 0.000082/1+0.74/1.63=0.45<1 Test Mode Test Frequency (MHz) Max.Output Power (dBm) Max.Output Power (mW) Power Density (mW/cm 2 ) Measurement Limit (mW/cm 2 ) BT 2440 -1.516 0.705 0.000082 1

Page 1 of 61 FCC Test Report Report No.: AGC01741230703FR01 FCC ID : 2AYT3-AC180P APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Portable Power Station BRAND NAME : BLUETTI MODEL NAME : AC180P APPLICANT : SHENZHEN POWEROAK NEWENER CO., LTD DATE OF ISSUE : Aug. 24, 2023 STANDARD(S) : FCC Part 15 Subpart C §15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC01741230703FR01 Page 2 of 61 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Aug. 24, 2023 Valid Initial Release Report No.: AGC01741230703FR01 Page 3 of 61 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RELATED SUBMITTAL(S)/GRANT(S) ....................................................................................................... 7 2.4. TEST METHODOLOGY ............................................................................................................................. 7 2.5. SPECIAL ACCESSORIES .......................................................................................................................... 7 2.6. EQUIPMENT MODIFICATIONS ................................................................................................................. 7 2.7. ANTENNA REQUIREMENT ....................................................................................................................... 7 2.8 DUTY CYCLE MEASUREMENT ......................................................................................................................... 8 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 9 4. DESCRIPTION OF TEST MODES ................................................................................................................. 10 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 11 5.1. CONFIGURATION OF TESTED SYSTEM ............................................................................................... 11 5.2. EQUIPMENT USED IN TESTED SYSTEM .............................................................................................. 11 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 11 6. TEST FACILITY .............................................................................................................................................. 12 7. PEAK OUTPUT POWER ................................................................................................................................ 13 7.1. MEASUREMENT PROCEDURE .............................................................................................................. 13 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 13 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 14 8. BANDWIDTH .................................................................................................................................................. 18 8.1. MEASUREMENT PROCEDURE .............................................................................................................. 18 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 18 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 18 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 25 9.1. MEASUREMENT PROCEDURE .............................................................................................................. 25 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 25 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 25 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 25 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ........................................................ 37 10.1. MEASUREMENT PROCEDURE ............................................................................................................ 37 10.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................. 37 10.3. MEASUREMENT EQUIPMENT USED .................................................................................................. 37 10.4. LIMITS AND MEASUREMENT RESULT................................................................................................ 37 11. RADIATED EMISSION ................................................................................................................................. 41 11.1. MEASUREMENT PROCEDURE ............................................................................................................ 41 11.2. TEST SETUP ..........................................................................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 18 Test Report Verified code: Report No.: E20230306359801-1-G1 Customer: Guangdong Bestcore Internet of Things Technology CO., Ltd. Address: Room1501,15F,ShuMao Building,6 Xiangxing Road, Torch Development District,Zhong shan Sample Name: LE ANT A Sample Model: LE ANT A Receive Sample Date: Mar.07,2023 Test Date: Mar.07,2023 ~ Mar.07,2023 Reference Document: ANSI IEEE 149-2021 Part 7, Part 8, Part 10 Test Result: Not make judgment Prepared by: Reviewed by: Approved by: GRG METROLOGY & TEST GROUP CO., LTD. Issued Date: GRG METROLOGY & TEST GROUP CO., LTD. Address: No.163,Pingyun Road, West of Huangpu Avenue, Guangzhou, Guangdong, China Tel：（+86）400-602-0999 FAX：（+86）020-38698685 Web：http://www.grgtest.com 348480 2023-03-17 Report No.: E20230306359801-1-G1 Page 2 of 18 Statement 1. The report is invalid without "special seal for inspection and testing"; some copies are invalid; The report is invalid if it is altered or missing; The report is invalid without the signature of the person who prepared, reviewed and approved it. 2. The sample information is provided by the client and responsible for its authenticity; The content of the report is only valid for the samples sent this time. 3. When there are reports in both Chinese and English, the Chinese version will prevail when the language problems are inconsistent. 4. If there is any objection concerning the report, please inform us within 15 days from the date of receiving the report. 5. Without the agreement of the laboratory, the client is not authorized to use the test results for unapproved propaganda. ------------ The following blanks ------------ Report No.: E20230306359801-1-G1 Page 3 of 18 TABLE OF CONTENTS 1. TEST RESULT SUMMARY ...................................................................................................................... 5 2. GENERAL DESCRIPTION OF EUT ......................................................................................................... 6 2.1 APPLICANT INFORMATION ...................................................................................................................... 6 2.2 MANUFACTURER ........................................................................................................................................ 6 2.3 FACTORY ...................................................................................................................................................... 6 2.4 BASIC DESCRIPTION OF EUT ................................................................................................................... 6 2.5 TEST SCENE .................................................................................................................................................. 6 2.6 SAMPLE WORK DESCRIPTION ................................................................................................................. 6 2.7 ASSISTIVE DEVICE INFORMATION......................................................................................................... 7 2.8 SAMPLE CONNECTION DIAGRAM .......................................................................................................... 7 3. LABORATORY .......................................................................................................................................... 8 4. MEASUREMENT UNCERTAINTY .......................................................................................................... 9 5. EQUIPMENT AND TOOLS USED DURING TEST .............................................................................. 10 6. ANTENNA RADIATION PERFORMANCE MEASUREMENT ........................................................... 11 6.1 LIMITS ......................................................................................................................................................... 11 6.2 TEST PROCEDURE ..................................................................................................................................... 11 6.3 CONFIGURATION OF SYSTEM UNDER TEST ...................................................................................... 12 6.4 TEST PHOTOS ............................................................................................................................................. 12 6.5 TEST RESULTS ........................................................................................................................................... 13 7. PHOTOGRAPH OF THE EUT ................................................................................................................. 17 ------------ The following blanks ------------ Report No.: E20230306359801-1-G1 Page 4 of 18 REPORT ISSUED HISTORY Report Version Report No. Description Compile Date 1.0 E20230306359801-1 Original Issue 2023-03-07 2.0 E20230306359801-1-G1 Update 2023-03-17 Note 1: This report E20230306359801-1-G1 is the modification of report E20230306359801-1. On the basis of the original report, Update Product Name Bluetooth Module to LE ANT A, Product Model BC204 to LE ANT A on page 1,6,13 of the report, and add Product Size: Antenna Size: 8.5mm*5.51mm*0.03mm, add Antenna Type: PCB Antenna, add Software Version: /, Hardware Version: /, add Manufacturer: Guangdong Bestcore Internet of Things Technology CO., Ltd. on page 6 of the report, and the original report E20230306359801-1 is invalid. ------------ The following blanks ------------ Report No.: E20230306359801-1-G1 Page 5 of 18 1. TEST RESULT SUMMARY Test Item Test Frequency Test Method Test Scene Test Result Gain 2400 MHz ~2500MHz ANSI IEEE 149-2021 Part 8 scene 1 / 1) Radiation efficiency 2400 MHz ~2500MHz ANSI IEEE 149-2021 Part 10 scene 1 / 1) Radiation pattern 2400 MHz ~2500MHz ANSI IEEE 149-2021 Part 7 scene 1 / 1) Note 1)：Customer-defined test, test results do not make judgment. ------------ The following blanks ------------ . Report No.: E20230306359801-1-G1 Page 6 of 18 2. GENERAL DESCRIPTION OF EUT 2.1 APPLI…

Text truncated - open the document above for the full version.

Report No.: AGC01741230703AP02 Page 1 of 11 TEST SETUP PHOTOS BT RADIATED EMISSION TEST SETUP BELOW 1GHz WITH BATTERY RADIATED EMISSION TEST SETUP BELOW 1GHz WITH AC Power Report No.: AGC01741230703AP02 Page 2 of 11 RADIATED EMISSION TEST SETUP ABOVE 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz WITH AC Power Report No.: AGC01741230703AP02 Page 3 of 11 AC POWER LINE CONDUCTED TEST SETUP RF CONDUCTED TEST SETUP Report No.: AGC01741230703AP02 Page 4 of 11 WPT RADIATED EMISSION TEST SETUP BELOW 30MHz WITH BATTERY RADIATED EMISSION TEST SETUP BELOW 30MHz WITH AC Power Report No.: AGC01741230703AP02 Page 5 of 11 RADIATED EMISSION TEST SETUP BELOW 1GHz WITH BATTERY RADIATED EMISSION TEST SETUP BELOW 1GHz WITH AC Power Report No.: AGC01741230703AP02 Page 6 of 11 AC POWER LINE CONDUCTED TEST SETUP Report No.: A…

Text truncated - open the document above for the full version.