2AZ4R-V23158-52RGB PATHY WAY LIGHT COLOR CHANGE 6CT C BULB LIGHT SET WITH CONTROLLER with push bottom AND REMOTE CONTROL.

6CT LED PATHWAY MARKERS ITM. / ART. 1487571 IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. a) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. b) This seasonal use product is not intended for permanent installation or use. c) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat. d) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. e) Do not let lamps rest on the supply cord or on any wire. f) Unplug the product when leaving the house, when retiring for the night, or if left unattended. g) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it. h) Do not use this product for other than its intended use. i) Do not hang ornaments or other objects from cord, wire, or light string. j) Do not close doors or windows on the product or extension cords as this may damage the wire insulation. k) Do not cover the product with cloth, paper or any material not part of the product when in use. l) This product is equipped with push-in type LED lamps. Do not twist lamps. m) This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded. n) Read and follow all instructions that are on the product or provided with the product. WARNING: This product is powered by a lithium battery. Due to their small size, lithium batteries can easily be swallowed by children. Ingestion of such batteries has been known to cause death. SAVE THESE INSTRUCTIONS CAUTION: To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal. b) Do not mount on support strings in manner that can cut or damage wire insulation. USE AND CARE INSTRUCTIONS a) When the product is placed on live a tree, the tree should be well maintained and fresh. Do not place on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water. b) If the product is placed on a tree, the tree should be well secured and stable. c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire. d) When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires. e) When not in use, store neatly in a cool, dry location protected from sunlight. f) The LED lamp has polarity. Do not deliberately change the direction of the LED lamp in the lampholder. USER SERVICING INSTRUCTIONS To replace the fuse: a) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. b) Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades. c) Remove fuse carefully. Turn plug over to remove fuse. d) RISK OF FIRE. Replace fuse only with 3 Amp, 125Volt fuse provided with product. e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug. f) RISK OF FIRE. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged. To replace a lamp: a) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. b) Be sure to pull lamp and plastic base straight out of lampholder. c) Replace lamp with only 3.2 volts, 0.064 watts LED type lamps provided with this product. If the new lamp base does not fit in lamp holder, follow the step below before Step c. NOTE - Be careful when exchanging the lamp base on the new lamp with the old one or the LED wires may break if leads are bent too many times. 1. Remove the base or burned out LED lamp by carefully straightening lamp leads and gently pull lamp out. 2. Thread leads of new LED lamp through holes in old base with one lead in each hole. 3. After lamp is fully inserted into base, bend each lead up, like other LED lamps in the light set so that the leads will touch the contacts inside the lamp holder. NOTE – To avoid damage to the set: 1. Do not deliberately change the direction of the LED lamp in the lampholder. 2. Use only the included spare LED bulbs for replacements, and only replace with the same color LED bulbs. 3. Do not switch the order of the colors of the bulbs or interchange bulbs from different sets and only use the same lamp base colors for replacements. Connecting Sets End to End: CAUTION: This string is rated 14.4 Watts (0.12Amps), do not overload. Connect other Lighting Strings or decorative outfits end-to-end up to a maximum of 3 sets (34W) total. DO NOT EXCEED THE SETS PERMITTED BY THE MARKINGS! CAUTION: a) Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Replace lamps only with the spare lamps provided with this product b) Replace lamps only with 3.2 volts, 0.064 watts spare LED lamps provided with this product. Do not connect more than 3 sets of products of the …

Text truncated - open the document above for the full version.

Lamues Light Enterprise Co., LTD Model Difference Product description: RGB PATHY WAY LIGHT COLOR CHANGE 6CT C BULB LIGHT SET WITH CONTROLLER with push bottom AND REMOTE CONTROL. Model name: V23158-52, 1487571, SL-003 Trade Name: N/A FCC ID: 2AZ4R-V23158-52 All the model are the same circuit and RF module, only for model name. Regards Sincerely Client’s signature: Client’s name / title : HE SHAOXIANG (QC MANAGER) Contact information / address: Trapeang Chrey, Kakab, PorSenChey, Phnom Penh, Cambodia

C5266091_X8_Ed.1 Letter of Authorization Lamues Light Enterprise Co., LTD Company: Lamues Light Enterprise Co., LTD Address: Trapeang Chrey, Kakab, PorSenChey, Phnom Penh, Cambodia Product Name: RGB PATHY WAY LIGHT COLOR CHANGE 6CT C BULB LIGHT SET WITH CONTROLLER with push bottom AND REMOTE CONTROL. Model Number: V23158-52 FCC Identifier: 2AZ4R-V23158-52 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: HE SHAOXIANG Date: May.26.2021 Title: MANAGER Signature of applicant: 1/1

C5266091_X10_Ed.2 Lamues Light Enterprise Co., LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: May.26.2021 Subject: Request for Confidentiality FCC ID: 2AZ4R-V23158-52 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature: Name: HE SHAOXIANG Title: MANAGER 1/1

External Photos        FCC ID: 2AZ4R-V23158-52               

Model: V23158-52 FCC ID: 2AZ4R-V23158-52 Label Location

Internal Photos FCC ID: 2AZ4R-V23158-52 ANT SI4432-B1

TEST REPORT Compiled by: Reviewed by: Approved by: Arron Liu Bin Mei Rita Xiao / Director The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen CTB Testing Technology Co., Ltd. this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. Product Name: RGB PATHY WAY LIGHT COLOR CHANGE 6CT C BULB LIGHT SET WITH CONTROLLER with push bottom AND REMOTE CONTROL. FCC ID: 2AZ4R-V23158-52 Trademark: N/A Model Number: V23158-52, 1487571, SL-003 Prepared For: Lamues Light Enterprise Co., LTD Address: Trapeang Chrey, Kakab, PorSenChey, Phnom Penh, Cambodia Manufacturer: Lamues Light Enterprise Co., LTD Address: Trapeang Chrey, Kakab, PorSenChey, Phnom Penh, Cambodia Prepared By: Shenzhen CTB Testing Technology Co., Ltd. Address: Floor 1&2, Building A, No. 26 of Xinhe Road, Xinqiao Street, Baoan District, Shenzhen China Sample Received Date: May. 18, 2021 Sample tested Date: May. 18, 2021 - May. 24, 2021 Issue Date: May. 24, 2021 Report No.: CTB210524017RFX Test Standards FCC Part15.231 ANSI C63.10:2013 Test Results PASS Remark: This is 433MHz radio test report. TABLE OF CONTENT Test Report Declaration Page 1. VERSION ...................................................................................................... 4 2. TEST SUMMARY ........................................................................................... 5 3. MEASUREMENT UNCERTAINTY .................................................................. 6 4. PRODUCT INFORMATION AND TEST SETUP ............................................... 7 4.1 Product Information ............................................................................................. 7 4.2 Test Setup Configuration ..................................................................................... 7 4.3 Support Equipment .............................................................................................. 7 4.4 Test Mode ........................................................................................................... 8 4.5 Test Environment ................................................................................................ 8 5. TEST FACILITY AND TEST INSTRUMENT USED .......................................... 9 5.1 Test Facility ......................................................................................................... 9 5.2 Test Instrument Used .......................................................................................... 9 6. AC POWER LINE CONDUCTED EMISSION ................................................... 11 6.1 Block Diagram Of Test Setup ............................................................................ 11 6.2 Limit ................................................................................................................... 11 6.3 Test procedure .................................................................................................. 11 6.4 Test Result ........................................................................................................ 12 7. RADIATED EMISSION ................................................................................. 13 7.1 Block Diagram Of Test Setup ............................................................................ 13 7.2 Limit ................................................................................................................... 13 7.3 Test procedure .................................................................................................. 14 7.4 Test Result ........................................................................................................ 15 8. DWELL TIME ............................................................................................... 22 8.1 Block Diagram Of Test Setup ............................................................................ 22 8.2 Limit ................................................................................................................... 22 8.3 Test procedure .................................................................................................. 22 8.4 Test Result ........................................................................................................ 23 9. OCCUPIED BANDWIDTH ............................................................................ 24 9.1 Block Diagram Of Test Setup ............................................................................ 24 9.2 Limit ................................................................................................................... 24 9.3 Test procedure .................................................................................................. 24 9.4 Test Result ........................................................................................................ 25 10. ANTENNA REQUIREMENT ......................................................................... 26 11. EUT PHOTOGRAPHS .................................................................................. 27 12. EUT TEST SETUP PHOTOGRAPHS ............................................................ 28 (Note: N/A means not applicable) 1. VERSION Report N o. Issue Date Description Approved CTB21 0524017RFX May. 24, 2021 Original Valid 2. TEST SUMMARY The Product has been tested according to the following specifications: Test Item Test Requirement Test method Result AC Power Line Conducted Emission 47 CFR Part 15 Subpart C Section 15.207 ANSI C63.10-2013 N/A Radiated Emission 47 CFR Part 15 Subpart C Section 15.209; 15.231(b) ANSI C63.10-2013 PASS Dwell Time 47 CFR Part 15 Subpart C Section 15.231 (a) ANSI C63.10-2013 PASS Occupied Bandwidth 47 CFR Part 15 Subpart C Section 15.231(c) ANSI C63.10-2013 PASS Antenna requirement 47 CFR Part 15 Subpart C Section 15.203 ANSI C63.10-2013 PASS…

Text truncated - open the document above for the full version.

Radiated Emission Below 1G Above 1G FCC ID: 2AZ4R-V 23158-52