2AZKE-SYMSLIMElectric Fireplace

INSTALLATION AND OPERATION INSTRUCTIONS FOR ELECTRIC FIREPLACE INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE. WARNING: This product can expose you to chemicals including lead in the wiring, which is [are] known to the State of California to cause birth defects of other reproductive harm. For more information visit: www.p65warnings.ca.gov SAFETY INFORMATION Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other. if the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. WARNING 1 www.amantii.com TD-190026-1 TABLE OF CONTENTS Please read and carefully follow all of the instruction found in this manual. Please pay special attention to the safety instructions provided in this manual. The instructions included here will assure that you have many years of dependable and enjoyable service from your Amantii product. 2 IMPORTANT INSTRUCTIONS CAUTIONS FCC STATEMENT UNPACKING AND TESTING APPLIANCE GROUNDING APPLIANCE LOCATING THE FIREPLACE PRODUCT SPECIFICATION OUTDOOR INSTALLATIONS INSTALLATION-WALL MOUNT INSTALLATION- BUILT-IN HARD- WIRE INSTALLATION DECORATIVE MEDIA INSTALLATION MANUAL OPERATION REMOTE CONTROL OPERATION REPLACEMENT PARTS EXPLODED VIEW ENERGY SAVING FUNCTION 3 4 4 5 5 5 6 8 9 10 13 14 16 15 18 TROUBLE SHOOTING 19 19 21 1. Read all instructions before installing or using this heater. 2. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from the front, sides and rear of the heater. 3. Always unplug heater when not in use. 4. Do not operate the fireplace if it has a damaged cord or plug, after it has malfunctioned, or if the unit has been dropped or damaged in any way. 5. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners or anything else. Arrange the cord away from traffic areas where it could not be tripped over. 6. To disconnect the heater, turn the controls to "OFF" before removing the plug from the outlet. 7. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the heater. 8. To prevent a possible fire, do not block air intakes in any manner. 9. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. 10. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury. 11. Avoid the use of an extension cord, the extension cord will overheat and cause a fire. This heater is not to be used with an extension cord. 12. Always use properly grounded fused and polarized outlets. 13. Always use ground fault protection where it is required by electrical codes. 14. Always disconnect the power before performing any cleaning, maintenance or relocation of the heater. 15. To prevent a possible fire, do not burn wood or other materials in this heater. 16. To prevent electric shock or fire, always use a certified electrician, should new circuits or outlets be required. 17. When transporting or storing the heater, keep it in a dry place, free from excessive vibration. 18. This appliance should not be modified under any circumstances. 19. Packaging material should be kept away from children and be disposed of in a safe manner. Plastic bags are not toys and should be kept away from children and infants. 20. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided. 21. If the glass is damaged, do not use the heater in order to avoid a hazard. 22. Do not leave children unsupervised where heater is turned on. 23. CAUTION Some parts of this product can become very hot and cause burns. Particular atten- tion has to be given where children and vulnerable people are present. 3 SAVE THESE INSTRUCTIONS CAUTIONS Always install the heater in accordance with this guide. If in doubt obtain expert advice. Always make sure the electrical socket is accessible and located adjacent to, but not above the heater. Always disconnect the heater from the electrical supply before moving it, or carrying out cleaning, maintenance. Always make sure the heater is firmly secured to prevent it from being tipped over. Always use a fireguard when young children and infirm persons can come into contact with the heater. Never leave children unsupervised in a room where the heater is ON and unguarded. Never obstruct or cover the fan outlet or force items into heater openings. Never use aerosols or steam cleaners on or around the heater. Never route the main supply cable under carpet etc. Never install the heater close to curtains or combustible materials. Never use the heater to dry clothes etc. Never sit or stand on the heater. Do’s Don’ts 4 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following mea- sures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from…

Text truncated - open the document above for the full version.

Differences Declaration To whom concern, We company AMANTII IMPORTS CORP hereby declares: TD-1900XX-XX, XX denotes 26,30,33,38,44,48; suffix XX denotes 1-9, TD-X1900XX-XX, XX denotes 26,30,33,38,44,48; suffix XX denotes 1-9, SM-1900XXX-XX, XXX denotes 34,42,45,50,60,,74,88,100; suffix XX denotes 1-9, SM-X1900XXX-XX, XXX denotes 34,42,45,50,55,60,65,74,88,100; suffix XX denotes 1-9, SM-T1900XXX-XX, XXX denotes 34,42,45,50,60,74,88,100; suffix XX denotes 1-9, BI-X1900XX-XX, XX denotes 30,35,40,45,50,55,60,65; suffix XX denotes 1-9, BI-S1900XX-XX, XX denotes 40,50,60,72,88; suffix XX denotes 1-9, DE-T1900XX-XX, XX denotes 40,45,50,55,60,65,72,88; suffix XX denotes 1-9, DE-1900XX-XX, XX denotes 40,45,50,55,60,65,72,88; suffix XX denotes 1-9, CUBE-2025WM, TV-S1900XX-XX, XX denotes30, 40,50,60,,72; suffix XX denotes 1-9, TV-1900XX-XX, XX denotes 40,50,60,,72; suffix XX denotes 1-9, TV-T1900XX-XX, XX denotes 40,50,60,,72; suffix XX denotes 1-9, INS-1900XX-XX, XX denotes 30,34; suffix XX denotes 1-9, FS26922-XX, suffix XX denotes 1-9, WM-G1900XX-XX, XX denotes 26,34,48,50,72,88; suffix XX denotes 1-9, WM-S1900XX-XX, XX denotes 26,34,48,60,72,88,; suffix XX denotes 1-9, WM-F1900XX-XX, XX denotes 40，48，62，85 ; suffix XX denotes 1-9, ZECL-31-3228-XX, suffix XX denotes 1-9, TV2939-XX, suffix XX denotes 1-9, VLR190XXXX-XX, suffix XX denotes 1-9, IR1900XX-XX, suffix XX denotes 1-9, BS2100XXX-XX, XXX 40、50、60、72、88,100 suffix XX denotes 1-9, BS1900XXX-XX, XXX denotes 34,42,50,60,74,88,100; suffix XX denotes 1-9, BS1910XXX-XX, XXX denotes 34,42,50,60,74,88,100; suffix XX denotes 1-9, BS2000XX-XX, XX denotes 26,30,33,38,44,48; suffix XX denotes 1-9 All above models are identical in the same PCB layout, interior structure and electrical circuits. The differences are appearance color and model name for commercial purpose. Authorized signature: Date: 2021-05-27

DATE : 2021-05-27 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AZKE-SYMSLIM Product Name: Electric Fireplace Request for Confidentiality To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature: Name: BRIAN RICHARDS Title: CEO Company: AMANTII IMPORTS CORP

DATE : 2021-05-27 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Jason Wu of Global United Technology Services Co., Ltd.and No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with AMANTII IMPORTS CORP And 502-1027 Davie Street, Vancouver, BC V6E4L2, Canada Signature: Name: BRIAN RICHARDS Title: CEO Company: AMANTII IMPORTS CORP

Test Model No.: SM-190042-1

Label: 5*10CM Product Name: Electric Fireplace Model No.: SM-190042-1 FCC ID: 2AZKE-SYMSLIM This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label location

Test Model No.: SM-190042-1

FCC ID: 2AZKE-SYMSLIM RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. FCC ID: 2AZKE-SYMSLIM Test Result of RF Exposure Evaluation Wifi Channel Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result Middle (2437MHz) 68.23 0.0271 1.0 PASS Remark: antenna gain=3dBi

Global United Technology Services Co., Ltd. Report No.: GTSL202104000263F02 Authorized Signature: Robinson Luo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 41 TEST REPORT Applicant: AMANTII IMPORTS CORP Address of Applicant: 502-1027 Davie Street, Vancouver, BC V6E4L2, Canada Manufacturer: Ningbo Globaltec Science & Technology Co., Ltd Address of Manufacturer: No.99 East Tanjialing Road, Yuyao, Zhejiang, China Factory: SHENZHEN VORX TECHNOLOGY CO.,LTD Address of Factory: 102 BUILDING D, STUDENT INDUSTRIAL PARK, HONGQIAOTOU COMMUNITY, YANLUO STREET , BAO'AN DISTRICT, SHENZHEN CHINA Equipment Under Test (EUT) Product Name: Electric Fireplace Model No.: See section 5.1 FCC ID: 2AZKE-SYMSLIM Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: May 19, 2021 Date of Test: May 20-26, 2021 Date of report issued: May 27, 2021 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 41 2 Version Version No. Date Description 00 May 27, 2021 Original Prepared By: Date: May 27, 2021 Project Engineer Check By: Date: May 27, 2021 Reviewer Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 41 3 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 VERSION ...................................................................................................................................................2 3 CONTENTS ...............................................................................................................................................3 4 TEST SUMMARY ......................................................................................................................................4 5 GENERAL INFORMATION .......................................................................................................................5 5.1 GENERAL DESCRIPTION OF EUT ..........................................................................................................5 5.2 TEST MODE .........................................................................................................................................9 5.3 DESCRIPTION OF SUPPORT UNITS ........................................................................................................9 5.4 DEVIATION FROM STANDARDS ..............................................................................................................9 5.5 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................9 5.6 TEST FACILITY ....................................................................................................................................9 5.7 TEST LOCATION ..................................................................................................................................9 5.8 ADDITIONAL INSTRUCTIONS ..................................................................................................................9 6 TEST INSTRUMENTS LIST ....................................................................................................................10 7 TEST RESULTS AND MEASUREMENT DATA .....................................................................................12 7.1 ANTENNA REQUIREMENT ....................................................................................................................12 7.2 CONDUCTED EMISSIONS ....................................................................................................................13 7.3 CONDUCTED PEAK OUTPUT POWER ...................................................................................................16 7.4 CHANNEL BANDWIDTH .......................................................................................................................17 7.5 POWER SPECTRAL DENSITY ..............................................................................................................18 7.6 SPURIOUS EMISSION IN NON-RESTRICTED & RESTRICTED BANDS ........................................................19 7.6.1 Conducted Emission Method ......................................................................................................19 7.6.2 Radiated Emission Method .........................................................................................................20 8 TEST SETUP PHOTO .............................................................................................................................41 9 EUT CONSTRUCTIONAL DETAILS .......................................................................................................41 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 41 4 Test Summary Test Item Section Result Antenna requirement FCC part 15.203/15.247 (c) Pass AC Power Line Conducted Emission FCC part 15.207 Pass…

Text truncated - open the document above for the full version.

Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 47 Appendix for 15.247 1. Duty Cycle 1.1 Test Result Test Mode Channel Frequency( MHz) TX Type ANT No. T_on (ms) Period (ms) Duty Cycle (%) Duty Cycle Correction Factor (dB) 802.11b 2412 SISO 1 8.380 8.410 99.64 0.02 2437 SISO 1 8.380 8.410 99.64 0.02 2462 SISO 1 8.380 8.410 99.64 0.02 802.11g 2412 SISO 1 1.360 1.396 97.42 0.11 2437 SISO 1 1.360 1.396 97.42 0.11 2462 SISO 1 1.360 1.396 97.42 0.11 802.11n(HT20) 2412 SISO 1 1.300 1.336 97.31 0.12 2437 SISO 1 1.299 1.335 97.30 0.12 2462 SISO 1 1.299 1.335 97.30 0.12 802.11n(HT40) 2422 SISO 1 0.618 0.652 94.79 0.23 2437 SISO 1 0.618 0.651 94.93 0.23 2452 SISO 1 0.618 0.651 94.93 0.23 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 47 1.2 Test Graph Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 47 2. Bandwidth 2.1 Test Result Test Mode Frequency (MHz) TX Type ANT No. 6dB Bandwidth Verdict Test Result (MHz) 802.11b 2412 SISO 1 9.115 PASS 2437 SISO 1 9.118 PASS 2462 SISO 1 9.552 PASS 802.11g 2412 SISO 1 15.145 PASS 2437 SISO 1 15.181 PASS 2462 SISO 1 15.671 PASS 802.11n(HT20) 2412 SISO 1 15.172 PASS 2437 SISO 1 15.122 PASS 2462 SISO 1 15.158 PASS 802.11n(HT40) 2422 SISO 1 35.287 PASS 2437 SISO 1 35.257 PASS 2452 SISO 1 35.244 PASS Test Mode Frequency (MHz) TX Type ANT No. 99% Occupied Bandwidth Test Result (MHz) 802.11b 2412 SISO 1 12.414 Only for Report Use 2437 SISO 1 12.411 Only for Report Use 2462 SISO 1 12.616 Only for Report Use 802.11g 2412 SISO 1 16.745 Only for Report Use 2437 SISO 1 16.808 Only for Report Use 2462 SISO 1 16.885 Only for Report Use 802.11n(HT20) 2412 SISO 1 17.666 Only for Report Use 2437 SISO 1 17.752 Only for Report Use 2462 SISO 1 17.795 Only for Report Use 802.11n(HT40) 2422 SISO 1 36.635 Only for Report Use 2437 SISO 1 36.595 Only for Report Use 2452 SISO 1 36.693 Only for Report Use Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 47 2.2 Test Graph - 6dB Bandwidth Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 10 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 11 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 12 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 13 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 14 of 47 Report No.: GTSL202104000263F02 Global United Technology Services Co., Ltd. No. 123-128, Tower A,Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzh…

Text truncated - open the document above for the full version.

Test Model No.: SM-190042-1 Radiated Emission Conducted Emission