2AZL5-VDM70PUsmart baby monitor/video baby monitor

User Guide babysense Touch+1 - 1 Camerababysense Touch+2 - 2 CamerasFor any product related question please contact us at:[email protected] Thank you for choosing Babysense Video Monitor from Hisense Ltd. TOUCH 7’’ Dual-mode video baby monitor Warnings and Safety Instructions Follow these safety precautions to prevent fire, injury or damage to the product. Read and keep instructions: It is very important that you read all the safety and operating instructions before the Babysense Video Monitor is operated. Please retain your purchase receipt as you will need to produce it if warranty service is required. WARNINGS STRANGULATION HAZARD: Children can become entangled in cords. Make sure the Baby Unit, Parent Unit and mains adaptor cables are kept out of reach of your baby and other young children at all times, at least 6 feet away. CHOKING HAZARD: This product contains small parts which may cause choking. Exercise care when unpacking and assembling the product and keep the small parts away from children. RISK OF SUFFOCATION: Keep all packaging materials and protective foils out of reach of children. DANGER FROM POWER CORDS: To avoid possible danger from power cords, the cords should be secured and never be hung on or near the crib. Never place the Baby unit or Parent unit inside your baby's crib, bed or playpen. DO NOT HANDLE ROUGHLY, DROP OR THROW: Babysense video monitor is a high-quality electronic device which must be handled with care. This product is designed for INDOOR USE ONLY. WATER AND MOISTURE: The product should not be exposed to rain, moisture, or splashing. Never use or place the product in or near moisture or water. Safety Instructions 2 THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION: Your video monitor is designed to be an aid and should not be used as a substitute for responsible and proper adult supervision of a child. POWER SOURCE: This product should only be used with the AC power adapters supplied by the manufacturer, as included in this package. VENTILATION: This product should not be used on a bed, sofa, rug or similar surface that may block the ventilation or speaker openings, or be placed in an enclosed area, such as a bookcase or drawer that may impede air flow. Never cover the product with clothes, towels, blankets or any other item. • THIS PRODUCT IS NOT A TOY: It should be kept out of children's reach. • KEEP AWAY FROM SOURCES OF HEAT: This unit should not be exposed to direct heat sources such as a candle, stove, radiator, heat register or other appliance that emit heat. The unit should not be left in direct sunlight. • BATTERY: Before you use the product, we recommend you fully charge the battery of the Parent Unit, so that it continues to work if you disconnect it from the power supply to carry it to another location. • INSTALLATION LOCATION: The installation location plays an important role in ensuring proper operation. Therefore, maintain a distance of at least 5 feet from other ̆˟ ̆˖˧˥ˢˡ ̃˖ ̆ˤ˨ ̃ˣˠ ̆ˡ˧ʟ˦˨˖ ̨˔˦ˠ ̃˖˥ˢ˪˔˩ ̆ˢ˩ ̆ˡ˦ˢ˥ˊ ̃ϸʹ ̃˥ˢ˨˧ ̆˥˦ʟ ˢ˧ ̨ ̆˥˪ ̃˦ ̆˧ ̨ ̆ˬ˖ˢ˨˟˗ cause interference. If this occurs, move the baby and parent units to another location. • RANGE: Range of all baby monitors is always measured in an open space. The actual range may be shortened due to environmental obstacles (such as concrete walls). • DAMAGE REQUIRING SERVICE: This product should be serviced by qualified personnel only. • DO NOT TRY TO OPEN AND REPAIR THE PRODUCT: If you have any problems with the product, please contact the authorized distributor. • In case of unusual noises or smells originating from the device, immediately disconnect the product from the power outlet and contact authorized distributor. • If the product becomes dirty, use a lightly damp soft cloth to wipe surfaces, taking care to not allow water into any openings. IMPORTANT: Babysense Video Monitor is designed only for hearing the baby’s voice and seeing the images of the baby. This product is not a medical device and should not be used as a substitute for responsible adult supervision. It is important that you regularly check on your baby personally. 3 Safety Instructions Safety Instructions for AC Power Adapter The adapter should not be exposed to direct heat sources such as a candle, stove, radiator, heat register or other appliance that emit heat. During continual use, the power adapters may become warm to the touch. This is normal and should not be a cause of concern. Examine the condition of the power cord and its plug. The adapter must be handled with care: do not handle roughly, drop or throw. When removing the power adapter from the wall outlet, hold and pull from the receptacle. Do not pull on the cable itself or bend the cable as that will put additional stress on the cable and could lead to damages. Do not touch the power adapter with wet hands or allow liquids to spill on it. Make sure the adaptor cables are kept out of reach of your baby and other young children at all times. To avoid possible danger from power cords, the cords should be secured and never be hung on or near the crib. Do not replace the plugs or cable on your power adapter. This product should only be used with the AC power adapters supplied by the manufacturer, as included in this package. Never cut, damage or bend the power cord. Do not put any objects on top of the power cord, which could cause overheating, damage, combustion and electrocution. Do not leave the power adapter connected to the wall outlet when it is not plugged into the Baby or Parent Unit. WARNING: Do not replace the AC power adapter with non-original substitutes. Improper connection may cause electrocution. Do not place the AC power adapter cable in a high wear and tear location. Never use a frayed or compromised cord. Intended for indoor use only. 4 Safety Instructions Safety Instructions for Li-ion battery (Non removable pre-installed battery) Do not attempt to repair or adjust any of the elect…

Text truncated - open the document above for the full version.

1/1 USAgentforServiceofProcessLETTEROFATTESTATION TO: OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USAgentforServiceofProcess: Companyname:HOPEKCORPORATIONINC FRN:0034562900 ContactName:YangyangXu Address:16755CoyoteBushDrUnit84,SanDiego,CA92127UnitedStates TelephoneNo:561-875-9826 Email:[email protected] Applicant: Companyname:HisenseLtd., GranteeCode:2AZL5 FCCID:2AZL5-VDM70PU FRN:0030807713 ContactName:NatalieShukrun Address: 27ShakedSt.HevelModi’inIndustrialParkIsrael TelephoneNo:+972528926339 FaxNo:+972-52-8926339 Email:[email protected] HisenseLtd.,certifiesthat,asofthedateofthisfilingoftheapplicationwiththeTCB,[HOPEK CORPORATIONINC]isourdesignatedUSagentforserviceofprocessfortheabovereferenced FCCID.HisenseLtd.,acceptstomaintainanagentfornolessthanoneyearafterthegrantee hasterminatedallmarketingandimportationortheconclusionofanycommissionrelated proceedinginvolvingequipment.[HOPEKCORPORATIONINC]accepts,asofthedateofthe filingoftheapplication,theobligationofthedesignatedUSagentforserviceofprocessforthe abovereferenceFCCID. TheUSAgentforServiceofProcessisawareofandagreestocomplywiththerequirements outlinedintheFCCEquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause §2.911. TheApplicantisawareofandagreestocomplywiththerequirementsoutlinedintheFCC EquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause§2.911. Date:2026-02-02 Applicant’sName:NatalieShukrunUSAgent’sName:YangyangXu Title:QA&RAManagerTitle:Manager Signature:Signature:

Hisense Ltd., February 2, 2026 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for FCC ID: 2AZL5-VDM70PU [Hisense Ltd.,] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber-security or anti-virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely, Natalie Shukrun Hisense Ltd., February 2, 2026 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for FCC ID: 2AZL5-VDM70PU [Hisense Ltd.,] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Natalie Shukrun

Hisense Ltd., 2/2/2026 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR Product Name: smart baby monitor/video baby monitor FCC ID: 2AZL5-VDM70PU Model(s): VDM70PU To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (Schematic Diagram, Block Diagram, Operational Description) required to be submitted with this application be permanently withheld from public review. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market Please contact me if there is any information you may need. Sincerely, Signature: February 2, 2026 Name Natalie Shukrun Position QA & RA Manager Company Name Hisense Ltd., Address 27 Shaked St. Hevel Modi’in Industrial Park Israel Tel +972528926339 Fax +972-52-8926339 Email [email protected]

Hisense Ltd., 2/2/2026 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Shenzhen PSI Testing Co., Ltd.) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This agreement expires one year from the current date. Sincerely, Signature: February 2, 2026 Name Natalie Shukrun Position QA & RA Manager Company Name Hisense Ltd., Address 27 Shaked St. Hevel Modi’in Industrial Park Israel Tel +972528926339 Fax +972-52-8926339 Email [email protected]

Page 1 of 5 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Appendix II external photos FCC ID: 2AZL5-VDM70PU Page 2 of 5 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Page 3 of 5 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Page 4 of 5 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Page 5 of 5 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China ------End------

Label and Location Material: Silk-screen Font color: White Size: L: 4cm*W: 1cm Label and Location W FCC ID: 2AZL5-VDM70PU Model No.: VDM70PU L

Page 1 of 6 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Appendix III internal photos FCC ID: 2AZL5-VDM70PU Page 2 of 6 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Page 3 of 6 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Page 4 of 6 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Page 5 of 6 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Page 6 of 6 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China ------End------ BT+2.4G WIFI ANTT

Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China RF Exposure evaluation FCC ID: 2AZL5-VDM70PU According to 447498 D01 General RF Exposure Guidance v06 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison BLE: Worse case output power is as below: [2480MHz: 1.00dBm] Maximum output power is 1.00dBm (1.26 mW). (1.26 mW /5mm)·[√2.480(GHz)]= 0.40 <3.0 for 1-g SAR. 2.4G WIFI: Worse case output power is as below: [2437MHz: 8.92dBm] Maximum output power is 8.92dBm (7.80 mW). (7.80 mW /5mm)·[√2.437(GHz)]= 2.43 <3.0 for 1-g SAR. BLE + 2.4G WIFI: 0.40+2.43=2.83 < 3.0 for 1-g SAR. Then SAR evaluation is not required.

SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com Headquarters Address: Building C, Hongyu Guangming Valley, No. 11 Youmagang Road, Matian Sub-district, Guangming District, Shenzhen Hangzhou Office: Room 212, Building B, Dahua Jianghong International Innovation Park, No. 369 Wulianwang Street, Binjiang District, Hangzhou TEL：0755-27810060 Fax：0755-27810057 CUSTOMER NAME Cheego CUSTOMER P/N PART NAME 2.4G Black FPC Built-in Antenna P/ N YJC-6N100-B107 APPROVAL REV. V1.0 DELIVERY DATE June 25, 2024 PREPARED BY Huang Teng CHECKED BY Wu Longfei APPROVED BY Xiao Han Customer Approved Prepared By Checked By Approved By SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com Table of Contents Cover ................................................................................................... 1 Table of Contents ................................................................................ 2 Revision History .................................................................................. 3 Antenna Layout Drawing .................................................................... 4 Antenna Technical Parameters & Environmental Testing .................. 5 Antenna Physical Diagram & Attachment Position Diagram ............. 6 Antenna Performance Test Diagram ................................................... 6 OTA Active Test Data Statistics ......................................................... 7 2D & 3D (2.4G) Test Data .................................................................. 7-9 RoHS Material Control Report ........................................................... 10 SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com Revision History： SHENZ Version Change Content & Reason Date Issuance V1.0 Initial Release June 25, 2024 SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com Antenna Layout Drawing： SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com Antenna Technical Parameters & Environmental Testing： Environmental Performance Test: Electrical Specifications Frequency Range 2400-2500MHz VSWR ＜1.92 Input Impedance 50 Ω Direction All Gain 4.0dBi Mechanical Specifications Antenna Color BLACK Input connector XD-1 Working Temperature -20°C~+70°C Working Humidity 20%~80% Item Test Conditions Specification Storage Environment Without specific requirements: 1. Temperature: -20°C～+70°C 2. Relative Humidity: 45%-85% 3. Air Pressure: 86kpa-106kpa Normal electrical and mechanical performance High-Low Temperature Test 5 cycles between 70°C and -20°C, then stand at normal conditions for 1-2H; inspect appearance quality Dimensional compliance + normal mechanical & electrical performance Steady Damp Heat Test Relative Humidity: 95±3%, Test Temperature: 40°C, Duration: 2H; measure electrical performance within 5min after removal, then stand at normal conditions for 1-2H; inspect appearance quality Dimensional compliance + normal mechanical & electrical performance Vibration Test Frequency Range: 10-55HZ, Displacement Amplitude: 0.35MM, Acceleration Amplitude: 50.0M/S, Sweep Cycle: 30 times Normal electrical and mechanical performance Drop Test Free drop from 1M height for 3 times along mutually perpendicular axes Normal electrical and mechanical performance SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com Antenna Physical View & Mounting Layout： Antenna Performance Test Chart： SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com OTA Active Test Data Statistics (2.4G)： 2D & 3D Test Data (2.4G)： Item Measurement Band Channel Frequency Max Min Total 1 TRP WIFI_B (11M) 1 2412 20.96 -3.37 16.35 2 TRP WIFI_B (11M) 6 2437 21.49 -2.93 16.92 3 TRP WIFI_B (11M) 11 2462 21.18 -3.3 16.58 4 TIS(EIRP) WIFI_B (11M) 1 2412 -67.58 -92.12 -87.55 5 TIS(EIRP) WIFI_B (11M) 6 2437 -66.06 -90.56 -85.99 6 TIS(EIRP) WIFI_B (11M) 11 2462 -65.71 -90.22 -85.63 Frequency Efficiency (%) Gain.(dBi) 2400MHz 56.75 3.39 2410MHz 62.23 4.13 2420MHz 59.57 3.72 2430MHz 60.81 4.51 2440MHz 52.48 3.36 2450MHz 59.70 3.80 2460MHz 57.94 4.00 2470MHz 57.54 4.23 2480MHz 52.12 3.12 2490MHz 51.29 3.27 2500MHz 48.64 2.76 Phi 0 2D Plot: Phi 90 2D Plot: Theta 90 2D Plot: SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com 3D Test Plot (3D 2400MHz)： (3D 2450MHz)： (3D 2500MHz)： SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com RoHS Material Control Report We hereby certify that the raw materials used for components, auxiliary materials, and additives in the production process delivered to your company comply with the environmental requirements of the RoHS Directive (Restriction of Hazardous Substances) (RoHS Directive 2011/65/EC). The composition report for raw materials used in components and auxiliary materials, packaging materials, and additives utilized during the production process is as follows: PASS? Cd Pb Hg Cr 6+ PBB PBDE PASS Wire Coaxial Cable CANEC24002746203 SGS 24/02/22 ND ND ND ND ND ND PASS FPC Copper Foil A2240082746101006E CTI 24/03/01 ND ND ND ND ND ND PASS 3M300LSE SHAEC23021627701 SGS 23/12/27 ND ND ND ND ND ND PASS Ink ETR23A00862M01 SGS 23/10/13 ND 4.86 ND ND ND ND PASS Solder Wire Environmental ly Friendly Solder Wire SZXEC23001647206 SGS 23/07/28 ND 63 ND ND ND ND PASS Connector Phosphor Bronze (XD) CANEC24000977302 SGS 24/01/22 ND 6 ND ND ND ND PASS Gold Plating A2230400553101001E CTI 23/08/12 ND ND ND ND ND ND PASS Test Org. Content of Hazardous Substances (ppm) Component /Part Name Material Composition ICP report # Test Date SHENZHEN YINGJIACHUANG ELECTRONIC TECHNOLOGY CO., LTD. http://www.szsyjc.com

Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Page 1 of 53 Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China FCC TEST REPORT FCC ID: 2AZL5-VDM70PU On Behalf of Hisense Ltd., smart baby monitor/video baby monitor Model No.: VDM70PU Prepared for : Hisense Ltd., Address : 27 Shaked St. Hevel Modi’in Industrial Park Israel Prepared By : Shenzhen PSI Testing Co., Ltd. Address : 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Report Number : psi2511129-C01-R01 Date of Receipt : November 27, 2025 Date of Test : November 28, 2025- December 8, 2025 Date of Report : December 8, 2025 Version Number : V0 Page 2 of 53 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China TABLE OF CONTENTS Description Page 1. Summary Of Standards And Results ---------------------------------------------------------- 6 1.1. Description of Standards and Results ---------------------------------------------------- 6 2. General Information --------------------------------------------------------------------------------- 7 2.1. Description of Device (EUT) ---------------------------------------------------------------- 7 2.2. Accessories of Device (EUT) --------------------------------------------------------------- 8 2.3. Tested Supporting System Details--------------------------------------------------------- 8 2.4. Block Diagram of Connection Between EUT and Simulators ---------------------- 8 2.5. Test Mode Description ------------------------------------------------------------------------ 9 2.6. Software test version and power setting information --------------------------------- 9 2.7. Test Conditions ------------------------------------------------------------------------------- 10 2.8. Test Facility ------------------------------------------------------------------------------------ 10 2.9. Measurement Uncertainty ----------------------------------------------------------------- 10 2.10. Test Equipment List-------------------------------------------------------------------------- 11 3. Spurious Emission --------------------------------------------------------------------------------- 12 3.1. Test Limits -------------------------------------------------------------------------------------- 12 3.2. Block Diagram of Test setup -------------------------------------------------------------- 13 3.3. Test Procedure -------------------------------------------------------------------------------- 14 3.4. Test Results------------------------------------------------------------------------------------ 15 4. Power Line Conducted Emission ------------------------------------------------------------- 22 4.1. Test Limits -------------------------------------------------------------------------------------- 22 4.2. Test Procedure -------------------------------------------------------------------------------- 22 4.3. Test Setup -------------------------------------------------------------------------------------- 22 4.4. Test Results------------------------------------------------------------------------------------ 23 5. Out-of-band Emissions --------------------------------------------------------------------------- 26 5.1. Test Limits -------------------------------------------------------------------------------------- 26 5.2. Test Procedure -------------------------------------------------------------------------------- 26 5.3. Test Setup -------------------------------------------------------------------------------------- 26 5.4. Test Results------------------------------------------------------------------------------------ 26 6. Conducted Maximum Output Power --------------------------------------------------------- 37 6.1. Test limits --------------------------------------------------------------------------------------- 37 6.2. Test Procedure -------------------------------------------------------------------------------- 37 6.3. Test Setup -------------------------------------------------------------------------------------- 37 6.4. Test Results------------------------------------------------------------------------------------ 37 7. Peak Power Spectral Density ------------------------------------------------------------------ 38 7.1. Test limits --------------------------------------------------------------------------------------- 38 7.2. Test Procedure -------------------------------------------------------------------------------- 38 7.3. Test Setup -------------------------------------------------------------------------------------- 38 7.4. Test Results------------------------------------------------------------------------------------ 38 8. Bandwidth --------------------------------------------------------------------------------------------- 42 8.1. Test limits --------------------------------------------------------------------------------------- 42 8.2. Test Procedure -------------------------------------------------------------------------------- 42 8.3. Test Setup -------------------------------------------------------------------------------------- 42 8.4. Test Results------------------------------------------------------------------------------------ 42 Page 3 of 53 Report No.: psi2511129-C01-R01 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China 9. Band Edge Test ------------------------------------------------------------------------------------- 49 9.1. Test Limit ----…

Text truncated - open the document above for the full version.

Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Page 1 of 114 Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China FCC TEST REPORT FCC ID: 2AZL5-VDM70PU On Behalf of Hisense Ltd., smart baby monitor/video baby monitor Model No.: VDM70PU Prepared for : Hisense Ltd., Address : 27 Shaked St. Hevel Modi’in Industrial Park Israel Prepared By : Shenzhen PSI Testing Co., Ltd. Address : 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China Report Number : psi2511129-C01-R02 Date of Receipt : November 27, 2025 Date of Test : November 28, 2025- January 30, 2026 Date of Report : January 30, 2026 Version Number : V0 Page 2 of 114 Report No.: psi2511129-C01-R02 Shenzhen PSI Testing Co., Ltd. Tel: 0755-23011775 | E-mail: [email protected] | http://www.psi-lab.com Add: 1-2/F., Building 5, Yudafu Industrial Park, No.10, Xingye West Road, Shajing Subdistrict, Bao'an District, Shenzhen, Guangdong, China TABLE OF CONTENTS Description Page 1. Summary Of Standards And Results ----------------------------------------------------------------------------------- 6 1.1. Description of Standards and Results --------------------------------------------------------------------------- 6 2. General Information --------------------------------------------------------------------------------------------------------- 7 2.1. Description of Device (EUT) --------------------------------------------------------------------------------------- 7 2.2. Accessories of Device (EUT) -------------------------------------------------------------------------------------- 8 2.3. Tested Supporting System Details-------------------------------------------------------------------------------- 8 2.4. Block Diagram of Connection Between EUT and Simulators ---------------------------------------------- 8 2.5. Test Mode Description ----------------------------------------------------------------------------------------------- 9 2.6. Software test version and power setting information------------------------------------------------------- 20 2.7. Test Conditions ------------------------------------------------------------------------------------------------------ 20 2.8. Test Facility ----------------------------------------------------------------------------------------------------------- 21 2.9. Measurement Uncertainty ---------------------------------------------------------------------------------------- 21 2.10. Test Equipment List ------------------------------------------------------------------------------------------------ 22 3. Spurious Emission --------------------------------------------------------------------------------------------------------- 24 3.1. Test Limits -------…

Text truncated - open the document above for the full version.