2AZLV-LED2100-SM10WLED LAMP

INSTRUCT ION MANUAL Please r ead this instruction manual and obey it strictly before using: 1.The LED bulb cannot be replaceable. 2.The external cable or cord of this luminaire cannot be replaced, if the cord is damaged, the luminaire shall be destroyed. 3.Avoid direct contact between bulb (or protect galss) and the hand or skin when to adjust the irradiation angle, using the handle. 4.This appliance should only be used indoor. it can’t be used after wetted. 5.Turn off the switch when nobody alongside. 6. Only use the transformer provided. 7.This product contains recyclable materials. Do not dispose this product as unsorted municipal waste. Please contact your local municipality for the nearest collection point. 8.Waterproof and dustproof IP20. 9. Place any Qi enabled device on the center of the lamp base for wireless charging. 10.Wireless module INPUT：12v,0.625A 7.5W（MAX）/ Output：5v ，1A， 5w（max） . 11.Product i nput voltage 12V，1.5A . Any Changes or modifications not expressly approved by the party responsible for c ompliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC rules. Operation is s ubject to the following two conditions: (1) this device may not c ause harmfui interference, (2) this device must accept any interfeience received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).

(Goods iQ) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AZLV-LED2100-SM10W Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram, Schematics, Operational Description Block Diagram .pdf, Schematics .pdf , Operation Description .pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Short-term confidentiality requested: 180 days Exhibit Type File Name Internal Photos, Test Setup Photos, Manual Internal Photos .pdf, Test Setup Photos .pdf, User Manual .pdf Sincerely, Holly Brien / Manager Goods iQ

Difference Statement Model Name: LED2100-QISM, LED2100-QISM-S, LED2100-QISM-FLT, LED-QISM2100-BKG-AMZ, LED2200-QISM-BK The only difference between all models is the color. The PCB schematic, PCB Layout, etc. are all the same. We choose model " LED2100-QISM " for RF testing. Holly Brien/Manager Goods iQ

(Goods iQ) Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: January 08, 2023 SUBJECT: FCC Application for FCC ID: 2AZLV-LED2100-SM10W To Whom It May Concern: We, the undersigned, hereby authorize Tony Wei at EMTEK(NINGBO) CO., LTD. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by EMTEK(NINGBO) CO., LTD. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Holly Brien / Manager Goods iQ

External photos: ---The End---

Label Location MODEL: LED2100-QISM FCC ID: 2AZLV-LED2100-SM10W Contains Transmitter Module FCC ID: 2AC7Z-ESP32PICOZERO Caution: This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Internal photos: Antenna ---The End---

Report No.EDG2208310038E00802R Page 1 of 13 Ver.1.0 TEST REPORT $二维码$ Product Name : LED LAMP Model Number : LED2100-QISM, LED2100-QISM-S, LED2100-QISM-FLT, LED-QISM2100-BKG-AMZ, LED2200-QISM-BK FCC ID : 2AZLV-LED2100-SM10W Prepared for : Goods iQ Address : 50 Romano Vineyard Way North Kingstown, RI 02852 Prepared by : EMTEK (DONGGUAN) CO., LTD. Address : -1&2F., Building 2, Zone A, Zhongda Marine Biotechnology Research and Development Base, No. 9, Xincheng Avenue, Songshanhu High-technology Industrial Development Zone, Dongguan, Guangdong, China Tel : +86-0769-22807078 Fax: +86-0769-22807079 Report Number : EDG2208310038E00802R Date(s) of Tests : August 31, 2022 to January 09, 2023 Date of Issue : January 10, 2023 Report No.EDG2208310038E00802R Page 2 of 13 Ver.1.0 TABLE OF CONTENT Test Report Description Page 1. SUMMARY OF TEST RESULT ............................................................................................. 3 2. GENERAL INFORMATION ................................................................................................... 5 2.1. DESCRIPTION OF DEVICE (EUT) ....................................................................................................................... 5 2.2. DESCRIPTION OF TEST FACILITY ........................................................................................................................ 5 2.3. MEASUREMENT UNCERTAINTY .......................................................................................................................... 6 3. MEASURING DEVICE AND TEST EQUIPMENT ................................................................. 7 3.1. FOR MPE MEASUREMENT ................................................................................................................................ 7 4. RF EXPOSURE..................................................................................................................... 8 4.1. MEASURING STANDARD .................................................................................................................................... 8 4.2. REQUIMENTS ................................................................................................................................................... 8 4.3. TEST CONFIGURATION ...................................................................................................................................... 9 4.4. LIMITS ........................................................................................................................................................... 10 4.5. MEASURING RESULTS ..................................................................................................................................... 11 Report No.EDG2208310038E00802R Page 3 of 13 Ver.1.0 TEST REPORT DESCRIPTION Applicant : Goods iQ Address : 50 Romano Vineyard Way North Kingstown, RI 02852 Manufacturer : Ningbo Chinyo Lighting Appliance Co., Ltd Address : No. 7, Ketai Road, Wangchun Industrial Zone Haishu District, Ningbo, Zhejiang Provincce, China. EUT : LED LAMP Model Name : LED2100-QISM, LED2100-QISM-S, LED2100-QISM-FLT, LED-QISM2100-BKG-AMZ, LED2200-QISM-BK Trademark : BLACK+DECKER Measurement Procedure Used: FCC Part 1(1.1310) and Part 2(2.1091) KDB 680106 D01 RF Exposure Wireless Charging App v03 The device described above is tested by EMTEK (DONGGUAN) CO., LTD. to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The measurement results are contained in this test report and EMTEK (DONGGUAN) CO., LTD. is assumed full of responsibility for the accuracy and completeness of these measurements. Also, this report shows that the EUT (Equipment Under Test) is technically compliant with the FCC requirements. This report applies to above tested sample only and shall not be reproduced in part without written approval of EMTEK (DONGGUAN) CO., LTD. Date of Test : August 31, 2022 to January 09, 2023 Prepared by : Warren deng /Engineer Reviewer : Tim Dong /Supervisor Approved & Authorized Signer : Sam Lv /Manager Report No.EDG2208310038E00802R Page 4 of 13 Ver.1.0 1. SUMMARY OF TEST RESULT EMISSION Description of Test Item Standard & Limits Results MPE FCC Part 1(1.1310) and Part 2(2.1091) KDB 680106 D01 RF Exposure Wireless Charging App v03 Pass Note: N/A is an abbreviation for Not Applicable. Report No.EDG2208310038E00802R Page 5 of 13 Ver.1.0 2. GENERAL INFORMATION 2.1. Description of Device (EUT) Product: LED LAMP Model Number: LED2100-QISM, LED2100-QISM-S, LED2100-QISM-FLT, LED-QISM2100-BKG-AMZ, LED2200-QISM-BK Sample Number: 1# Power Supply: DC 12V from adapter Adapter: Model: RSS1006-240120-W2-J-P Input: 100-240V 50/60Hz 1.4A Output: 12V 2A Wireless specification 10W(MAX) Modulation: Ask Maximum Power Rate: 79.65 dBuV/m Frequency Range: 110 kHz~205 KHz Antenna Type: Integral Antenna(Induction coil) Antenna Gain: 0 dBi Operating Temperature 0°C ~ +50°C Date of Received: August 31, 2022 Report No.EDG2208310038E00802R Page 6 of 13 Ver.1.0 2.2. Description of Test Facility Site Description EMC Lab. : Accredited by CNAS, 2020.08.27 The certificate is valid until 2024.07.05 The Laboratory has been assessed and proved to be in compliance with CNAS/CL01:2018 The Certificate Registration Number is L3150 Accredited by FCC Designation Number: CN1300 Test Firm Registration Number: 945551 Accredited by A2LA, April 05, 2021 The Certificate Registration Number is 4321.02 Accredited by Industry Canada The Certificate Registration Number is CN0113 Name of Firm : EMTEK (Dongguan) Co., Ltd. Site Location : -1&2/F.,Buiding 2,Zone A,Zhongda Marine Biotechnology Research and Development Base,N.9,Xincheng Avenue,Songshanhu High-technology Industrial Development Zone, Dongguan, Guangdong, China 2.3. Measurement Uncertainty MPE : ±2 % Report No.EDG2208310038E00802R Page 7 of 13 Ver.1.0 3. MEASURING DEVICE AND TEST EQUIPMENT 3.1. For MPE Measurement Used Equip…

Text truncated - open the document above for the full version.

Coil parameters：A7 12.5μH/14 circle，Silk covered wire 0.07*100P Coil picture： Manufacturer : Goods iQ Address : 50 Romano Vineyard Way North Kingstown, RI 02852. Gain : 0.0 dBi

Radiated CONDUCTED EMISSION MPE ---The End---