2AZLVKT2-BASEWRLSWireless charging station with pencil cup

廠商(Supplier) 代號(Item No.) 品名(Description) 材質(Material) 尺寸(Size) Pusher KT2-CLUBKITQI_A02810 Instruction sheets Wood Free Paper 375x260mm(B4) Front 1 color 2021.3.9 S1 momo K100 K 顏色(Colors) 特別色 (Pantone) 4色(CMYK) 日期(Date) 版本(Version) 製稿(DRN) 審校(CHD) 業務(Sales) This device complies with Part 15 of the FCC rules. Operation is subject to thefollowing two conditions: 1) this device may not cause harmful interference, and 2)this device must accept any interference received, including interference that maycause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. Wireless charging station with pencil cup

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: 2021/04/17 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AZLVKT2-BASEWRLS KT2-BASEWRLS-XXX For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Holly Brien/Manager Company: Goods iQ Address: 50 Romano Vineyard Way North Kingstown, RI 02852 United States Phone: (401) 889-3114 E-Mail: [email protected]

Goods iQ 50 Romano Vineyard Way North Kingstown, RI 02852 United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2021/04/17 To whom it may concern: We, Goods iQ the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AZLVKT2-BASEWRLS including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Holly Brien/Manager Company: Goods iQ Address: 50 Romano Vineyard Way North Kingstown, RI 02852 United States Phone: (401) 889-3114 E-Mail: [email protected]

FCC ID: 2AZLVKT2-BASEWRLS External Photos of the EUT Fig.1 Fig.2 FCC ID: 2AZLVKT2-BASEWRLS Fig.3 Fig.4 FCC ID: 2AZLVKT2-BASEWRLS Fig.5 Fig.6

FCC ID: 2AZLVKT2-BASEWRLS Label and Location Size: L: 4.0cm*W: 3.0cm Label and Location Wireless charging station with pencil cup Trade Mark: Bostitch, PaperPro Model No.: KT2-BASEWRLS-XXX FCC ID: 2AZLVKT2-BASEWRLS Caution : This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2AZLVKT2-BASEWRLS Internal Photos of the EUT Fig.1 Fig.2 FCC ID: 2AZLVKT2-BASEWRLS Fig.3 Fig.4

Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 6 RF Exposure Evaluation FCC ID: 2AZLVKT2-BASEWRLS 1 Measuring Standard KDB 680106 D01 RF Exposure Wireless Charging Apps v03 2 Requirements According to the item 5 of KDB 680106 D01v03: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. (1) Power transfer frequency is less than 1MHz. (2) Output power from each primary coil is less than or equal to 15 watts. (3) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. (4) Client device is placed directly in contact with the transmitter. (5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). (6) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Remark: Meet all the above requirements. Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 6 3 Test Setup 4 Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The measurement probe was placed at test distance (15 cm from all sides and 20 cm from the top) which is between the edge of the charger and the geometric center of probe. 3) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E) were completed. 4) The EUT was measured according to the dictates of KDB 680106 D01v03. Remark：The EUT’s test position A, B, C, D and E is valid for the E and H field measurements. 5 Equipment Approval Considerations The EUT does comply with KDB 680106 D01 as follow table. Requirements of KDB 680106 D01 Yes / No Description Power transfer frequency is less than 1 MHz Yes The device operate in the frequency range 110KHz~205KHz Output power from each primary coil is less than 15 watts Yes The maximum output power for each primary coil is 15W. The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. Yes The transfer system includes two primary coils but can only transmit between a pair of primary and secondary coils at the same time. Client device is placed directly in contact with the transmitter. Yes Client device is placed directly in contact with the transmitter. Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). Yes Mobile exposure conditions only The aggregate H-field strengths at 15 cm Yes The EUT H-field strengths at 15 cm Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 6 surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. 6 Description of the test mode Equipment under test was operated during the measurement under the following conditions: Charging and communication mode Test Modes: Mode 1 AC/DC Adapter (5V/2A) + EUT + Mobile Phone1 (Battery Status: <1%) Pre-tested Mode 2 AC/DC Adapter (5V/2A) + EUT + Mobile Phone1 (Battery Status: <50%) Pre-tested Mode 3 AC/DC Adapter (5V/2A) + EUT + Mobile Phone1 (Battery Status: 100%) Pre-tested Mode 4 AC/DC Adapter (9V/2A) + EUT + Mobile Phone1 (Battery Status: <1%) Record Mode 5 AC/DC Adapter (9V/2A) + EUT + Mobile Phone1 (Battery Status: <50%) Record Mode 6 AC/DC Adapter (9V/2A) + EUT + Mobile Phone1 (Battery Status: 100%) Record Note: All test modes were pre-tested, but we only recorded the worst case in this report. 7 Description of Support Units Follow auxiliary equipment(s) test with EUT that provided by the manufacturer or laboratory is listed as follow: Description Manufacturer Model Technical Parameters Certificate Provided by Adapter UGREEN CD137 Input: 100-240V~, 50/60Hz, 0.5A Output: 5V2A / 9V2A CE/FCC laboratory / / / / / / / / / / / / / / / / / / Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 6 8 Test Instruments list Test Equipment Manufacturer Model No. SN. Cal.Date (mm-dd-yy) Cal.Due date (mm-dd-yy) Exposure Level Tester Narda ELT-400 N-0231 June 29 2020 June 28 2021 Magnetic field probe 100cm 2 Narda ELT probe 100cm 2 M0675 June 29 2020 June 28 2021 9 Test Result H-Field Strength at 15 cm from the edges surrounding the EUT and 15cm from the top surface of the EUT Chargin g Battery Level Unit Frequency Range (MHz) Measured E-Field Strength Values (A/m) FCC H-Field Strength 50% Limits (A/m) FCC H-Field Strength Limits (A/m) Test Position A Test Position B Test Positi…

Text truncated - open the document above for the full version.

Shenzhen Global Test Service Co.,Ltd. No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong FCC PART 15 SUBPART C TEST REPORT Report Reference No. ..................... : FCC ID. ............................................ : GTS20210415005-1-1 2AZLVKT2-BASEWRLS Compiled by ( position+printed name+signature) .. : File administrators Jimmy Wang Supervised by ( position+printed name+signature) .. : Test Engineer Aaron Tan Approved by ( position+printed name+signature) .. : Manager Jason Hu Date of issue ..................................... : Apr. 15, 2021 Representative Laboratory Name .: Shenzhen Global Test Service Co., Ltd. Address ............................................ : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong Applicant’s name ............................ : Goods iQ Address ............................................ : 50 Romano Vineyard Way North Kingstown, RI 02852 Test specification ...........................: Standard ........................................... : FCC Rules and Regulations Part 15 Subpart C (Section 15.209), ANSI C63.10: 2013 Shenzhen Global Test Service Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purpses as long as the Shenzhen Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Wireless charging station with pencil cup Trade Mark ....................................... : Bostitch, PaperPro Manufacturer .................................... : DONGGUAN PUSHER ELECTRONIC FACTORY Model/Type reference....................... : KT2-BASEWRLS-XXX Listed Models .................................. : N/A Modulation Type ............................... : ASK Operation Frequency ........................ : From 110KHz~205KHz Rating ............................................... : DC 5V/2A or 9V/2A Result................................................ : PASS Report No.: GTS20210415005-1-1 Page 2 of 23 T E S T R E P O R T Test Report No. : GTS20210415005-1-1 Apr. 15, 2021 ____________________________________________________________________________________ Date of issue Equipment under Test : Wireless charging station with pencil cup Model /Type : KT2-BASEWRLS-XXX Listed Models : N/A Applicant : Goods iQ Address : 50 Romano Vineyard Way North Kingstown, RI 02852 Manufacturer : DONGGUAN PUSHER ELECTRONIC FACTORY Address : HSIN-MEN-LO MANAGEMENT DISTRICT, DONG-KEN CHEN, DONGGUAN GUANGDONG 511734 CHINA Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: GTS20210415005-1-1 Page 3 of 23 Contents 1 T E S T S T A N D A R D S ................................................................. 4 2 S U M M A R Y ............................................................................ 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Description of the test mode 5 2.4 Special Accessories 6 2.5 Modifications 6 3 T E S T E N V I R O N M ENT .............................................................. 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Environmental conditions 7 3.4 Summary of measurement results 8 3.5 Statement of the measurement uncertainty 8 3.6 Equipments Used during the Test 8 4 T E S T C O N D I T I O N S A N D R E S U L T S ........................................... 10 4.1 AC Power Conducted Emission 10 4.2 Radiated Emission 13 4.3 Occupied Bandwidth 17 4.4 Antenna Requirement 18 5 T E S T S E T U P P H O T O S O F T H E E U T ......................................... 19 6 PH O T O S O F T H E E U T ........................................................... 20 Report No.: GTS20210415005-1-1 Page 4 of 23 1 T E S T ST A N D A R D S The tests were performed according to following standards: FCC Rules and Regulations Part 15 Subpart C (Section 15.207): Conducted limits. FCC Rules and Regulations Part 15 Subpart C (Section 15.209): Radiated emission limits; general requirements. ANSI C63.10: 2013: American National Standard for Testing Unlicensed Wireless Devices Report No.: GTS20210415005-1-1 Page 5 of 23 2 S U MM A R Y 2.1 General Remarks Date of receipt of test sample : Mar. 05, 2021 Testing commenced on : Mar. 05, 2021 Testing concluded on : Apr. 15, 2021 2.2 Product Description Product Name: Wireless charging station with pencil cup Model/Type reference: KT2-BASEWRLS-XXX Test samples ID: GTS20210415005-1-1# Power supply: DC 5V/2A or 9V/2A Operation frequency: 110KHz - 205KHz Modulation type: ASK Antenna type: Loop coil antenna 2.3 Description of the test mode Equipment under test was operated during the measurement under the following conditions: Charging and communication mode Test Modes: Mode 1 AC/DC Adapter (9V/2A) + EUT + Wireless charger tester (Load 15W) Record Mode 2 AC/DC Adapter (9V/2A) + EUT + Wireless charger tester (Load 10W) Pre-tested Mode 3 AC/DC Adapter (9V/2A) + EUT + Wireless charger tester (Load 5W) Pre-tested Mode 4 AC/DC Adapter (5V/2A) + EUT + Wireless charger tester (Load 15W) Pre-tested Mode 5 AC/DC Adapter (5V/2A) + EUT + Wireless charger tester (Load 10W) Pre-tested Mode 6 AC/DC Adapter (5V/2A) + EUT + Wireless charger tester (Load 5W) Pre-tested Note: All test modes were pre-tested, but we only recorded the worst case in this report. Report No.: GTS20210415005-1-1 Page 6 of 23 2.4 Special Accessories Follow auxiliary equipment(s) test with EUT that provided by the manufac…

Text truncated - open the document above for the full version.

FCC ID: 2AZLVKT2-BASEWRLS Test Setup Photos of the EUT Test Setup Photo(s) of Radiated Emissions Measurement Fig. 1 Fig. 2 FCC ID: 2AZLVKT2-BASEWRLS Test Setup Photo of Line Conducted Emissions Measurement