2AZWI-3263LEQIWireless Receiver Motor

In order to ensure the safety of users and prevent product damage caused by improper use, please carefully read the "Important Notes" in this manual before use,And keep the manual properly for future reference Important Tips Please read this user manual carefully. Please do not use it in water. This product does not have the function of dustproof and waterproof. Please avoid strong extrusion or impact on the product. This product contains a built-in non removable lithium battery. It is strictly prohibited to disassemble the machine without authorization. There are a few harmful substances in the battery. Please do not discard them at will. Please recycle the damaged or unused products according to the waste management method. Up and down keys: 1. Frequency band adjustment; 2. Motor number adjustment. REC interface: REC interface of wired control camera. Interface: power supply port and communication interface. Battery hanging plate interface: used with battery hanging plate (3777), compatible with NPF series batteries. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. IC Warnin g English: This device complies with Part 15 of the FCC Rules [and contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS standard(s)]. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B). French: L’émetteur/récepteurexempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et DéveloppementéconomiqueCanada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. l'appareil numérique du ciem conforme canadien peut ‐ 3 (b) / nmb ‐ 3 (b). This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance. cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs rf et la conformité. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. Cet équipement est conforme aux limites d'exposition aux rayonnements du Canada établies pour un environnement non contrôlé. RF Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be usedin portable exposurecondition without restriction. L'appareil a été évalué pour répondre aux exigences générales d'exposition aux radiofréquences. L'appareil peut être utilisé en condition d'exposition portable sans restriction.

FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Appendix II EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT

FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Appendix IFCC ID&IC Label Size for the label: 30mm X 30mm FCC ID: 2AZWI-3263LEQI IC: 27649-3263LEQI HVIN/Model No.: 3263

FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Photo 7 Internal of EUT Photo 8 Appearance of PCB FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Photo 9 Appearance of PCB Photo 10 Appearance of PCB FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Photo 11 Appearance of PCB Photo 12 Appearance of PCB FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Photo 13 Appearance of PCB Photo 14 Appearance of PCB FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Photo 15 Appearance of PCB Photo 16 Appearance of PCB Antenna FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Photo 17 Appearance of PCB Photo 18 Appearance of PCB

version01 Shenzhen Leqi Network Technology Co., LTD Declaration concerning Antenna Specification It is hereby declared that the product Model No.: 3263 FCC ID: 2AZWI-3263LEQI fulfills the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for FPC antenna type(s) described below: Antenna No. Model No. of antenna: Type of antenna: Gain of the antenna (Max.) Frequency range: ZigBee / FPC Antenna 1.92dBi for 2405-2480MHz; The mounting of the antenna is fixed to the radio module and no other antenna should be used. Company name: Shenzhen Leqi Network Technology Co., LTD Address: Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50 Guanguang Road, Longhua District, Shenzhen, Guangdong, China. Place: Jolin Zhong Date: 2022-9-14 Signature:

深圳市凯普深通讯科技有限公司 Shenzhen Kaipushen Communication Technology Co., Ltd Sample approve sheet Customer： Leqi Item name： 3263 Sample name： ZigBee aerial -2 Description/color：black Release Date：2022/6/23 Supplier confirmed MakeR&DStructureQuality Liu Xiao meng 2022-07 -22 Customer confirmed ItemAppearanceStructureQuality Conclusion □ MP use□Limited use （ ）K □ROHS Supplier name：Shenzhen Kaipushen Communication Technology Co., Ltd Supplier address：2nd Floor, Building 1, Yulong Building, Longcheng Industrial Zone, No.440, Longguan Avenue, Longhua District, Shenzhen Tel: 0755-29351613 Fax: 0755-29351510 E-mail:[email protected] 此文件中所包含的一切信息版权归深圳市凯普深 通讯科技有限公司所有，在未得到深圳市凯普深通讯科技有限公司的书面许可下，请勿散播给任何第三方。 Contents 1、 Cover 2、 Contents 3、 ICD Drawing(BT aerial) 4、 Aerial data 5、 Full dimensional measurement report 6、 Salt spray test report 7、 High-low temperature test 8、 Package 3.ICD Drawing 深圳市凯普深天线科技有限公司 4.1 Aerial function 4.1-1 Specificatin standard The working frequency band of wifi antenna produces resonance at 2400m-2500m 4.1-2 Matching circuit of antenna. The antenna matching circuit is as follows： 4.2 Standing wave ratio test （VSWR）: 4.2-1 Test settings The standing wave ratio test device is connected in turn：E571BNetwork analyzer→ 50Coaxial line of OhmCable→150mmlong copper pipe→test fixture。 Treatment of test fixture：Use a hard cable to lead out from the 50 ohm test point of the antenna on the PCB of the machine u...SMA-JThe joint is connected with the copper pipe with choke ring, and then connected with other devices。 4.2-2 Voltage standing wave ratio test : The following table shows： WIFIStanding wave ratio of edge frequency points of antenna operating frequency band： Fre(MHZ)240024502500 VSWR1.51.31.6 此文件中所包含的一切信息版权归深圳市凯普深 通讯科技有限公司所有，在未得到深圳市凯普深通讯科技有限公司的书面许可下，请勿散播给任何 第三方。 深圳市凯普深天线科技有限公司 4.2-3 Passive test results 4.3 Environmental manipulation: 此文件中所包含的一切信息版权归深圳市凯普深 通讯科技有限公司所有，在未得到深圳市凯普深通讯科技有限公司的书面许可下，请勿散播给任何 第三方。 深圳市凯普深通讯科技有限公司 Full dimensional measurement report Customer LeqiItem name 3262Material Electrolyti c copper Supplier Kaipushen Measure tools Quadratic Measure unit MM Measure date 2022/7/28 N O . dimURL+ TOL.- TOL.LR actual 1actual 2actual 3actual 4actual 5actual 6actual 7UPPER≦100%LOWER≦100% 1 17.40 17.50 0.10 0.10 17.3017.41 17.38 17.38 17.37 17.42 17.42 17.42 20%30% 2 14.11 14.21 0.10 0.10 14.0114.09 14.13 14.13 14.13 14.09 14.08 14.09 20%30% 3 4 5 6 7 8 9 10 11 Tabulation：Jian ChenExamine and Verify :Wu Xingtuo 此文件中所包含的一切信息版权归深圳市凯普深 通讯科技有限公司所有，在未得到深圳市凯普深通讯科技有限公司的书面许可下，请勿散播给任何第三方。 深圳市凯普深通讯科技有限公司 Salt spray test report Date：2022 年 07 月 28日 Item3262-FPC aerialCustomerLeqi Supplier Shenzhen Kaipushen Communication Technology Co., Ltd National Test standard GB/T 2423.2-2008 Sample situation Sample qty：5PCS Base material:Half to one-third electrolytic copper with glue Test time Total 24H Test type: ■ NSS□ ASS□ CASS Test condition Salt solution：5% PH:7.0 Chamber temp：35°C Relative humidity：85% Spray way： ■ continuation □intermittence Compressed air pressure：1kg/cm² Salt spray sedimentation rate：1- 2ml/80cm2/h Fog fluid collection： 1.4ml/80cm2/h Test cycle：__1__cycle Spray time： 24 h Test results Appearance after test:appearance intact, without obvious change Coating: no spalling, no rust Surface spraying, silk screen: no falling off, no bubbles. Explanation： 1、 Salt spray test operating standards in accordance with the People's Republic of China national standard GB/T2423.17-2008 implementation。 2、The test piece results are determined according to the national standard GB/ T6451-02 of the People's Republic of China。 Operator by/date：Jian Chen Approved by/date：Wu Xingtuo 2022.07.29 此文件中所包含的一切信息版权归深圳市凯普深 通讯科技有限公司所有，在未得到深圳市凯普深通讯科技有限公司的书面许可下，请勿散播给任何第三方。 High-low temperature test record Product name3262Customer nameLeqi Test qtu5 pcsTest date2022年7月28日 Cycle number 1Time24H Test Condition： High temp： + 65 degrees Humidity： 90 % RH Low temp： - / degree Test time： high temp： 24 H low temp： 24 H Test item Uncycled testCycled test NoAfter high tempAfter low tempAfter high temp After low temp 1OKOK 2OKOK 3OKOK 4OKOK 5OKOK 6OKOK After test deficiency:: Reason analysis： Improvement measures： Test results： √ Pass Fail 深圳市凯普深通讯科技有限公司 Packing Customer： Leqi Material name： 3262-FPC aerial packing qty： one carton Packing material： Carton Qty/carton：Packing way：Ziplock bag Picture 1:Single package Picture 2: Packing way Picture 3: Packing view (front, side, top) Picture 4:packing l Fiction：LiMinghuiauditing：Wu Xingtuo 此文件中所包含的一切信息版权归深圳市凯普深 通讯科技有限公司所有，在未得到深圳市凯普深通讯科技有限公司的书面许可下，请勿散播给任何第三方。

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202208-0186-14 Page: 1 of 5 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 RF Exposure Evaluation FCC ID: 2AZWI-3263LEQI IC: 27649-3263LEQI 1. Client Information Applicant : Shenzhen Leqi Network Technology Co., LTD Address : Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50 Guanguang Road, Longhua District, Shenzhen, Guangdong, China. Manufacturer : Shenzhen Leqi Network Technology Co., LTD Address : Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50 Guanguang Road, Longhua District, Shenzhen, Guangdong, China. 2. General Description of EUT EUT Name : Wireless Receiver Motor HVIN/Model No. : 3263 Sample ID : RW-C-202208-0186-10-1#&RW-C-202208-0186-10-2# Product Description : Operation Frequency: ZigBee: 2405MHz~2480MHz Number of Channel: ZigBee: 16channels RF Output Power: 0.77dBm Antenna Gain: 1.92dBi FPC Antenna Power Supply : Input: DC 5V/2A Software Version : V1.2 Hardware Version : V1.0 Remark: The antenna gain provided by the applicant, the adapter and verified for the RF conduction test and adapter provided by TOBY test lab. Note: More test information about the EUT please refer the RF Test Report. Report No.: TBR-C-202208-0186-14 Page: 2 of 5 TB-RF-074-1.0 The RF Exposure Evaluation for FCC: SAR Test Exclusion Calculations FCC: According to 447498 D04 Interim General RF Exposure Guidance v01. The SAR-based exemption formula of § 1.1307(b)(3)(i)(B), repeated here as Formula (B.2), applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power or effective radiated power (ERP), whichever is greater, of less than or equal to the threshold P th (mW). This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). P th is given by Formula (B.2). and f is in GHz, d is the separation distance (cm), and ERP 20cm is per Formula (B.1). The example values shown in Table B.2 are for illustration only. Table B.2—Example Power Thresholds (mW) Report No.: TBR-C-202208-0186-14 Page: 3 of 5 TB-RF-074-1.0 Calculation: Test separation: 5mm ZigBee Mode Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dBm) Max power of tune up tolerance (mW) Limit P th (mW) 2.405 0.77 0±1 1 1.259 3 2.445 0.22 0±1 1 1.259 3 2.480 0.08 0±1 1 1.259 3 The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 D04, No SAR is required. Report No.: TBR-C-202208-0186-14 Page: 4 of 5 TB-RF-074-1.0 The RF Exposure Evaluation for IC: SAR Test Exclusion Calculations IC: According to RSS-102 — Radio Frequency (RF) Exposure Compliance of Radio Communication Apparatus (All Frequency Bands) Issue 5: March 19, 2015 (1) Clause 2.5.1: Exemption limits for Routine Evaluation – SAR Evaluation SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance defined in Table 1. Table 1: SAR evaluation — Exemption limits for routine evaluation based on frequency and separation distance Frequency (MHz) Exemption Limits (mW) At separation distance of ≤5 mm At separation distance of 10 mm At separation distance of 15 mm At separation distance of 20 mm At separation distance of 25 mm ≤300 71 mW 101 mW 132 mW 162 mW 193 mW 450 52 mW 70 mW 88 mW 106 mW 123 mW 835 17 mW 30 mW 42 mW 55 mW 67 mW 1900 7 mW 10 mW 18 mW 34 mW 60 mW 2450 4 mW 7 mW 15 mW 30 mW 52 mW 3500 2 mW 6 mW 16 mW 32 mW 55 mW 5800 1 mW 6 mW 15 mW 27 mW 41 mW Table 1: SAR evaluation — Exemption limits for routine evaluation based on frequency and separation distance Frequency (MHz) Exemption Limits (mW) At separation distance of 30 mm At separation distance of 35 mm At separation distance of 40 mm At separation distance of 45 mm At separation distance of ≥50 mm ≤300 223 mW 254 mW 284 mW 315 mW 345 mW 450 141 mW 159 mW 177 mW 195 mW 213 mW 835 80 mW 92 mW 105 mW 117 mW 130 mW 1900 99 mW 153 mW 225 mW 316 mW 431 mW 2450 83 mW 123 mW 173 mW 235 mW 309 mW 3500 86 mW 124 mW 170 mW 225 mW 290 mW 5800 56 mW 71 mW 85 mW 97 mW 106 mW Report No.: TBR-C-202208-0186-14 Page: 5 of 5 TB-RF-074-1.0 Calculation: ZigBee Mode Frequency (MHz) Max Conducted Power (dBm) Tune-up Power (dBm) Antenna Gain (dBi) Max. E.I.R.P (dBm) Max. E.I.R.P (mw) Limit Result 2405 0.77 0±1 1.92 2.92 1.959 ≤4mw PASS 2445 0.22 0±1 1.92 2.92 1.959 ≤4mw PASS 2480 0.08 0±1 1.92 2.92 1.959 ≤4mw PASS Note: At separation distance of ≤5 mm Conclusion: The measurement results comply with the FCC Limit per 47 CFR 2.1093 and the RSS-102§4 Table 4 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06, No SAR is required. -----END OF REPORT-----

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0186-17 Page: 1 of 20 FCC ID: 2AZWI-3263LEQI & IC: 27649-3263LEQI TB-RF-074-1.0 RF Test Data for ZigBee (Conducted Measurements) General Description of EUT Product Name: Wireless Receiver Motor Test Model: 3263 Sample ID: RW-C-202208-0186-10-2# Environmental Conditions Temperature: 25°C Relative Humidity: 55% Test Voltage: DC 5V Test Engineer: Huang jian ping Note: For a more detailed features description, please refer to the report TBR-C-202208-0186-17 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0186-17 Page: 2 of 20 FCC ID: 2AZWI-3263LEQI & IC: 27649-3263LEQI TB-RF-074-1.0 Contents 1: DTS Bandwidth ............................................................................................................................................... 3 1.1 Test Result ......................................................................................................................................... 3 1.2 Test Graphs ....................................................................................................................................... 4 2: Occupied Channel Bandwidth ....................................................................................................................... 5 2.1 Test Result ......................................................................................................................................... 5 2.2 Test Graphs ....................................................................................................................................... 6 3: Maximum conducted output power .............................................................................................................. 7 3.1 Test Result ......................................................................................................................................... 7 4: Maximum power spectral density ................................................................................................................. 8 4.1 Test Result ......................................................................................................................................... 8 4.2 Test Graphs ....................................................................................................................................... 9 5: Band edge measurements ........................................................................................................................... 10 5.1 Test Result ....................................................................................................................................... 10 5.2 Test Graphs ..................................................................................................................................... 11 6: Conducted Spurious Emission...................................................................................................................... 12 6.1 Test Result ....................................................................................................................................... 12 6.2 Test Graphs ..................................................................................................................................... 13 7: Duty Cycle .................................................................................................................................................... 16 7.1 Test Result ....................................................................................................................................... 16 7.2 Test Graphs ..................................................................................................................................... 17 8: Emissions in Restricted Bands ...................................................................................................................... 18 8.1 Test Result ....................................................................................................................................... 18 8.2 Test Graphs ..................................................................................................................................... 19 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0186-17 Page: 3 of 20 FCC ID: 2AZWI-3263LEQI & IC: 27649-3263LEQI TB-RF-074-1.0 1: DTS Bandwidth 1.1 Test Result Test Mode Antenna Frequency[MHz] DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict ZigBee Ant1 2405 0.82 2404.41 2405.23 0.5 PASS 2445 1.44 2444.30 2445.74 0.5 PASS 2480 1.74 2479.15 2480.89 0.5 PASS Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0186-17 Page: 4 of 20 FCC ID: 2AZWI-3263LEQI & IC: 27649-3263LEQI TB-RF-074-1.0 1.2 Test Graphs ZigBee_Ant1_2405 ZigBee_Ant1_2445 ZigBee_Ant1_2480 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0186-17 Page: 5 of 20 FCC ID: 2AZWI-3263LEQI & IC: 27649-3263LEQI TB-RF-074-1.0 2: Occupied Channel Bandwidth 2.1 Test Result TestMode Antenna Frequency[MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict ZigBee Ant1 2405 2.268 2403.8212 2406.0889 --- --- 2445 2.218 2443.8511 2446.0689 --- --- 2480 2.258 2478.8212 2481.0789 --- --- Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, B…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202208-0186-17 Page: 1 of 35 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Radio Test Report FCC ID: 2AZWI-3263LEQI IC: 27649-3263LEQI Report No. : TBR-C-202208-0186-17 Applicant : Shenzhen Leqi Network Technology Co., LTD Equipment Under Test (EUT) EUT Name : Wireless Receiver Motor Model No. : 3263 Series Model No. : ---- Brand Name : SmallRig Sample ID : RW-C-202208-0186-10-1#&RW-C-202208-0186-10-2# Receipt Date : 2022-08-15 Test Date : 2022-08-15 to 2022-09-08 Issue Date : 2022-09-14 Standards : FCC Part 15 Subpart C 15.247 RSS-247 Issue 2 February 2017 RSS-Gen Issue 5 March 2019 Test Method : ANSI C63.10: 2013 KDB 558074 D01 15.247 Meas Guidance v05r02 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above. Witness Engineer : Wade. Lv Engineer Supervisor : Ivan Su Engineer Manager : Ray Lai This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TBR-C-202208-0186-17 Page: 2 of 35 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................. 2 1. GENERAL INFORMATION ABOUT EUT.............................................................................. 5 1.1 Client Information ................................................................................................................. 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 7 1.5 Description of Test Mode .................................................................................................... 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility ........................................................................................................................... 9 2. TEST SUMMARY ..................................................................................................................... 10 3. TEST SOFTWARE ................................................................................................................... 10 4. TEST EQUIPMENT .................................................................................................................. 11 5. CONDUCTED EMISSION ....................................................................................................... 12 5.1 Test Standard and Limit .................................................................................................... 12 5.2 Test Setup ........................................................................................................................... 12 5.3 Test Procedure ................................................................................................................... 12 5.4 Deviation From Test Standard ......................................................................................... 13 5.5 EUT Operating Mode ........................................................................................................ 13 5.6 Test Data ............................................................................................................................. 13 6. RADIATED AND CONDUCTED UNWANTED EMISSIONS ............................................ 14 6.1 Test Standard and Limit .................................................................................................... 14 6.2 Test Setup ........................................................................................................................... 15 6.3 Test Procedure ................................................................................................................... 16 6.4 Deviation From Test Standard ......................................................................................... 17 6.5 EUT Operating Mode ........................................................................................................ 17 6.6 Test Data ............................................................................................................................. 17 7. RESTRICTED BANDS REQUIREMENT ............................................................................. 18 7.1 Test Standard and Limit .................................................................................................... 18 7.2 Test Setup ........................................................................................................................... 18 7.3 Test Procedure ................................................................................................................... 19 7.4 Deviation From Test Standard ......................................................................................... 20 7.5 EUT Operating Mode ........................................................................................................ 20 7.6 Test Data ............................................................................................................................. 20 8. BANDWIDTH TEST ................................................................................................................. 21 8.1 Test Stan…

Text truncated - open the document above for the full version.

FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Appendix V EUT Test Photographs 15C Test Setup Photo of Setup for Radiated Emission (Above 1 GHz) Photo of Setup for Radiated Emission (Above 1 GHz) FCC ID: 2AZWI-3263LEQI &IC: 27649-3263LEQI TB-RF-074-1.0 Photo of Setup for Radiated Emission (Below 1 GHz) Photo of Setup for Conducted Emission -----END OF REPORT-----