2BA9S-P31Tablet PC

QUICK START GUIDE Technical Parameters Packagecontent: Type-C USB connector Model:P31 Read this manual carefully before operating the Rebeosoii Tablet Product Name:Tablet PC Model:P31 System:Android TM 13.0 Android is a trademark of Google LLC; Dimension:W260mm × H164mm × D7.2mm Weight:Approximately 511g BatteryCapacity:7000mAh Device USB Cable USB poweradaptor Temperglass(LCDProtector) Connect the Type-C USB connector to charge the battery with a Type-C USB cable Do not plug a Type-C USB cable into your device multipurpose jack.Doing so may damage the device ABOUT THE TABLET 1. front camera 2. USB Type-C (charging &data transfer) 3. micro SD 4.pogo pin 5. touch screen 6. back camera flash7. 8.volume+ 9. volume- 10.on/off button 11.reset 12. speaker 13. microphone Made in PRC Accessing more information To view the full user manual on your device launch the Setting app and tap User Manual. Visit www.rebeosoii.com to view device information, the manual and more. Maintaining water and dust resistance The device may be damaged if water or dust enters the device. Follow these tips carefully to preventdamage to the device and to maintain thewaterand dust resistant performance of the device. Do not immerse the devicein waterdeeper the 1.5m or keep it submerged for more then 3 minutes. Do not expose the device to water moving with force. Perhaps the device exposed to clean water, dry it thoroughly with a cleansoft clothIfthe device is exposed to otherliquidssuchas salt waterionized wateroralcoholic beverage rinse it with clean water and dryit thoroughly with a clean soft cloth.if you do not follow these instructionsthe device performanceand appearance may be affected. If the device has been immersed in wateror microphone or speakeriswetsoundmaynot be heard clearly during a call. After wiping the device with a dry cloth, dry it thoroughly before using it. TURNING ON Press and hold the power button for a couple of seconds to turn on your tablet. You might need to charge the tablet first. EXPANDING STORAGE You can expand your storage space for saving files and installing programs by adding microSD card (microSD, microSDHC or microSDXC). The maximum supported capacity is 64 GB. 6 7 1 2 313 9 8 10 11 12 12 4 5 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. The FCC Statement of Exposure to RF and the SAR limit for the United States (FCC) is 1.6 W/kg average for each gram of tissue. This device was tested for typical operations of use on the body. This device was tested for typical operations 0mm from the body.

1/1 US Agent for Service of ProcessLETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: THREE STONES MEDIA LLC FRN: 0033401761 Contact Name: Sijie Zhang Address:1200 Broadway St. APT 329, Los Angeles, CA90015 Telephone No: +1 267 909 3692 Email: [email protected] Applicant: Company name: Epudo(Hongkong)Digital Technology Limited Product Description: Tablet PC Grantee code: 2BA9S FCC ID: 2BA9S-P31 Contact Name: Barrett Chen Address: ROOM 803, CHEVALIER HOUSE 45-51 CHATHAM ROAD SOUTH, TSIM SHA TSUI, KL Telephone No: +8613923483515 Email: [email protected] [Epudo(Hongkong)Digital Technology Limited] certifies that, as of the date of this filing of the application with the TCB, [THREE STONES MEDIA LLC] is our designated US agent for service of process for the above referenced FCC ID. [Epudo(Hongkong)Digital Technology Limited] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [THREE STONES MEDIA LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicantis aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. 1/1 Date: 30/06/2023 Applicant’s Name:Barrett Chen US Agent’s Name:Sijie Zhang Title:manager Title: President Signature Signature

C5266091_X24_Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Epudo(Hongkong)Digital Technology Limited Grantee code: 2BA9S FCC ID: 2BA9S-P31 Contact Name: Barrett Chen Address: ROOM 803, CHEVALIER HOUSE 45-51 CHATHAM ROAD SOUTH, TSIM SHA TSUI, KL Telephone No: +8613923483515 Fax No: N/A Email: [email protected] i. [Epudo(Hongkong)Digital Technology Limited] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Epudo(Hongkong)Digital Technology Limited] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. Theapplicantmustsignthiscertification. Epudo(Hongkong)Digital Technology Limitedcertifies that, as of the date of the filing of theapplication, the applicant is notidentified on the Covered List as an entity producing “covered”equipment. Date: 30/06/2023 Applicant’s Name:Barrett Chen Title: Manager Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

Epudo(Hongkong)Digital Technology Limited Family models declaration letter. 6/30/2023 We Company: Epudo(Hongkong)Digital Technology Limited Address: ROOM 803, CHEVALIER HOUSE 45-51 CHATHAM ROAD SOUTH, TSIM SHA TSUI,KL Product: Tablet PC Model Name: ES306 Family Model: P31 All models are the same circuit and RF module,except the model name. We (Epudo(Hongkong)Digital Technology Limited) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.), same mechanical structure and design (including product enclosure, materials, etc.), the only difference are the same circuit and RF module, except the model name. Thanks Sincerely, Signature [Name] Barrett Chen [Title] Gernal manager [email protected]

C5266091_X8_Ed.1 1/1 Letter of Authorization <Epudo(Hongkong)Digital Technology Limited> Company:Epudo(Hongkong)Digital Technology Limited Address: ROOM 803, CHEVALIER HOUSE 45-51 CHATHAM ROAD SOUTH, TSIM SHA TSUI, KL Product Name:Tablet PC Model Number: ES306, P31 FCC Identifier:2BA9S-P31 We authorize LGAI Technological Center S.A., Ronda de la Font delCarme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Barrett Chen Date: 30/06/2023 Title: manager Signature of applicant:

C5266091_X10_Ed.2 1/1 <Epudo(Hongkong)Digital Technology Limited> Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046Date: 30/06/2023 Subject: Request for Confidentiality FCC ID: 2BA9S-P31 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No Block Diagram ☐ Schematics ☐ Test Report No No Test Setup Photos No User’s Manual ☐ NOTE 1 Internal Photos ☐ NOTE 1 Parts List / Tune Up / BOM List ☐ RF Exposure Info No No Operational Description ☐ Cover Letter(s) No No SOFTWARE SECURITY REQUIREMENTS FOR U- NII DEVICES No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of _180_ days from the date of the Grant of Equipment Authorization and prior to marketing. C5266091_X10_Ed.2 1/1 It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Barrett Chen Title: manager

ATTACHMENT PHOTOGRAPHS OF EUT Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7

Product: Tablet PC Model No.: ES306 FCC ID: 2BA9S-P31 40*20mm

ATTACHMENT PHOTOGRAPHS OF EUT Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10 Photo 11 BT/WIFI/GPS ANT

Page 1 of 95 Report No.: S23041403403001 FCC SAR EVALUATION REPORT In accordance with the requirements of FCC 47 CFR Part 2(2.1093), ANSI/IEEE C95.1-1992 and IEEE Std 1528-2013 Product Name： Tablet PC Trademark： REBEOSOII Model Name： ES306 Family Model： P31 FCC ID： 2BA9S-P31 Report No.： S23041403403001 Prepared for Epudo(Hongkong)Digital Technology Limited ROOM 803, CHEVALIER HOUSE 45-51 CHATHAM ROAD SOUTH, TSIM SHA TSUI, KL Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao'an District, Shenzhen 518126 P.R.China. Tel. 400-800-6106, 0755-2320 0050, 0755-2320 0090 Website: http://www.ntek.org.cn Page 2 of 95 Report No.: S23041403403001 TEST RESULT CERTIFICATION Applicant’s name .................. : Epudo(Hongkong)Digital Technology Limited Address .................................. : ROOM 803, CHEVALIER HOUSE 45-51 CHATHAM ROAD SOUTH, TSIM SHA TSUI, KL Manufacturer's Name ........... : Epudo(DongGuan)Digital Technology Co.Ltd Address .................................. : No.5 Plant,Huanan Science Park 5th Road,Tianxin Village,Tangxia Town,Dongguan,China Product description Product name ......................... : Tablet PC Trademark ............................ : REBEOSOII Model Name ......................... : ES306 Family Model .......................... : P31 Standards .............................. : FCC 47 CFR Part 2(2.1093) ANSI/IEEE C95.1-1992 IEEE Std 1528-2013 Published RF exposure KDB procedures This device described above has been tested by Shenzhen NTEK. In accordance with the measurement methods and procedures specified in IEEE Std 1528-2013 and KDB 865664 D01. Testing has shown that this device is capable of compliance with localized specific absorption rate (SAR) specified in FCC 47 CFR Part 2(2.1093) and ANSI/IEEE C95.1-1992. The test results in this report apply only to the tested sample of the stated device/equipment. Other similar device/equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. This report shall not be reproduced except in full, without the written approval of Shenzhen NTEK, this document may be altered or revised by Shenzhen NTEK, personal only, and shall be noted in the revision of the document. Test Sample Number .............................. S230414034003 Date of Test Date (s) of performance of tests ............. : May 04, 2023 ~ May 07, 2023 Date of Issue .......................................... : May 15, 2023 Test Result .............................................. : Pass Prepared By (Test Engineer) : (Jack Li) Approved By (Lab Manager) : (Alex Li) Page 3 of 95 Report No.: S23041403403001 ※ ※ Revision History ※ ※ REV. DESCRIPTION ISSUED DATE REMARK Rev.1.0 Initial Test Report Release May 15, 2023 Jack Li Page 4 of 95 Report No.: S23041403403001 TABLE OF CONTENTS 1. General Information ............................................................................................ 6 1.1. RF exposure limits .................................................................................... 6 1.2. Statement of Compliance ........................................................................ 7 1.3. EUT Description ....................................................................................... 7 1.4. Test specification(s) .................................................................................. 9 1.5. Ambient Condition ................................................................................... 9 2. SAR Measurement System ................................................................................. 10 2.1. SATIMO SAR Measurement Set-up Diagram .......................................... 10 2.2. Robot ..................................................................................................... 11 2.3. E-Field Probe .......................................................................................... 12 2.3.1. E-Field Probe Calibration ................................................................. 12 2.4. SAM phantoms ...................................................................................... 13 2.4.1. Technical Data .................................................................................. 14 2.5. Device Holder ........................................................................................ 15 2.6. Test Equipment List ................................................................................ 16 3. SAR Measurement Procedures .......................................................................... 18 3.1. Power Reference ................................................................................... 18 3.2. Area scan & Zoom scan .......................................................................... 18 3.3. Description of interpolation/extrapolation scheme .............................. 20 3.4. Volumetric Scan ..................................................................................... 20 3.5. Power Drift ............................................................................................ 20 4. System Verification Procedure .......................................................................... 21 4.1. Tissue Verification ................................................................................. 21 4.1.1. Tissue Dielectric Parameter Check Results ...................................... 22 4.2. System Verification Procedure .............................................................. 23 4.2.1. System Verification Results .............................................................. 24 5. SAR Measurement variability and uncertainty .................................................. 25 5.1. SAR measurement variability ................................................................. 25 5.2. SAR measurement uncertainty .............................................................. 25 6. RF Exposure Positions .…

Text truncated - open the document above for the full version.

Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Customer name:Yipuda Project name: ES306-10.95 "metal shell - Biota W863 motherboard -MT8183V main control Date:2023.04.20 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Customer contact: cell phone: Mail: Soward radio frequency：Xiao Chunyan Mobile phone: Tel：0755-29985185 Mail box：[email protected] Soward structure: Mobile phone: Tel: 0755-29985185 Mail box: [email protected] Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen 1.Project Overview Project Antenna NumberMachine type 1Three-in-one plate Shell material: 10.95 "metal shell (plastic parts at both ends) 2.Antenna Brief Antenna number nameWorking frequency/MHZ Material/Struct ure 1WIFI&BT&5Gwifi2400MHz/2500MHz&5.8GHzFPC Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen GPS&WIFI&BT antenna Antenna layout Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WIFI&BT antenna S11 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WIFI Antenna active data Model number channel b mode（11MHz）g mode（54MHz）n mode（MCS0/7）a mode（54MHz） TRPTISTRPTISTRPTISTRPTIS 1 1 9.7-80.898.7-68.889.2-64.58NANA 69.45-81.698.42-69.479.47-64.97NANA 1110.52-82.458.62-69.99.72-65.43NANA 36NANANANA5.53-63.295.94-67.54 100NANANANA7.99-65.368.37-69.68 161NANANANA10.7-66.3810.65-69.66 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WiFi throughput Iperf throughput test Machine type ES306- Biota W863 motherboard module MT8183V master control Software version Magic_Iperf Model numberFrequency banddistanceTest Angle Test data (TX) 1min mean value Mean value of test data (RX) in 1min Remarks (times of switching) 1 2.4G 5G 2.4G WIFI （Research and development environment 15m ） 0°34.6 Mbps66.9 Mbps0 90°34.4 Mbps56.9 Mbps0 056.9 Mbps37.3 Mbps180° 270°37.4 Mbps60.1 Mbps0 0°225 Mbps297 Mbps 5F WIFI （Research and development environment 15m ） 0 0293 Mbps236 Mbps90° 180°268 Mbps293 Mbps0 0292 Mbps278 Mbps270° Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WIFI antenna throughput test (test picture) Test data 2.4G/5G wifi upload/download (corresponding connection rate is 86/433Mbps) Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Measured distance of BT antenna Measured effect Model number 1 Test environment Soward Research and Development Center Test equipment Huawei AM08 Test distance 10 m ≥ WIFI&BT Antenna Efficiency (%) 2400 -6.91 1.341.34 2470 21.68 0.77 -0.3 11.221 23.14 -21.09 -16.95 0.77 -6.62 -6.7 13.453 (dBd)(MHz) 1.0410.573 2460 21.62 1.36 1.85 -0.18 23.46 -19.47 -17.04 10.745 -6.64 -6.36 13.855 (dBi) Freq 2450 0.96 -1.11 (%) 1.5 -17.79 9.825 1.9724.67 -17.31-0.79 -6.65 -6.3 12.923 UHIS 9.55 2440 (dB) 1.04 -0.99 Effie 1.97 -16.36 11.55725.41 (dB) -18.37 1.36 -6.08 11.244 10.83 Gain -1.78 2430 Max 10.589 1.16 2500 2.02 (dB) -0.13 23.79 Effie -19.5 10.825 0.37 -5.95 11.457 11.416 Gain 2420 (%) 1.85 -1.19 10.304 2490 Min 2.02 21.07 20.38 -20.42 -0.65 9.941 -6.24 11.108 12.397 Passive Test For 2.4G wifi 0.96 2410 DHIS 1.16 -0.81 2480 21.76 0.37 10.863 21.36 -21.53 11.026 1.5 -1.38 -6.76 12.64 6th Floor, Building B, Hexi Hangcheng Industrial Zone, No. 135, Qianjin 2nd Road, Baoan District, Shenzhen Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Machine Translated by Google 2.2 5GWIFI Antenna Efficiency (%) -6.99 7.99 6.984 DHIS -4.25 -1.59 10.117 5100 5800 -2.98 -0.84 0.44 15.45 -1.75 10.782 -17.16 (dBd) -8.01 21.187 (dB) -6.4 -0.84 8.659 5000 5700 0.44 -1.06 1.31 18.97 -1.68 9.074 -17.92 (dBi) 34.08 -7.39 24.28 Effie -1.06 9.081 0.82 (dB) 5600 1.31 1.56 14.76 -2.68 12.021 -19.27 UHIS 38.68 -7.35 22.207 (%) Min 0.82 7.455 -0.83 5500 1.56 -3.74 0.4 20.01 8.833 -21.25 -16.19 Gain 37.57 -8.11 12.784 Effie (dB) -0.83 8.184 12.89 5400 0.4 -2.99 0.47 15.82 22.9 -1.71 -21.89 -19.09 Gain -7.22 9.585 5.688 (MHz) Max -4.68 14.404 5300 0.47 -3.21 -0.53 6000 18.24 -0.84 -17.83 -20.37 Passive Test For 5G wifi Freq -8.31 9.322 7.985 (%) -4.12 -0.53 15.366 5200 -1.33 -1.59 -22.03 5900 18.4 -0.59 -19.52 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen 6th Floor, Building B, Hexi Hangcheng Industrial Zone, No. 135, Qianjin 2nd Road, Baoan District, Shenzhen Machine Translated by Google -7.6 -5.6 -3.6 -2.1 -0.6 0.9 1.56 5800.000MHz Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WIFI antenna signal intensity measured picture (data) Test location: R&D office of our company Test time: 16:00-1630 Test distance: 10-15 meters Signal strength: -49dBm to -38dBm Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen GPS measured pictures (data) Test location: the roof of our company Test time: 17:45 to 17:15 Test direction: East, South, west and North Cold start positioning time: < 60sec Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen drawing Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Antenna matching Main antenna 123456备注 Original matching Change matching RＦ ２ 1 3 5 4 6 antenna Antenna matching has not changed。 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Environmental handling and assembly instructions 1. At the red frame on the back of the motherboard, the conductive sponge is attached to make the motherboard and the screen fully grounded; 2. The front blue frame of the motherboard is connected to the screen with conductive cloth; In the red frame, the conductive sponge is connected…

Text truncated - open the document above for the full version.

Report No.: S23041403402002 Version.1.3 Page 1 of 53 RADIO TEST REPORT FCC ID: 2BA9S-P31 Product: Tablet PC Trade Mark: REBEOSOII Model No.: ES306 Family Model: P31 Report No.: S23041403402002 Issue Date: May 10, 2023 Prepared for Epudo(Hongkong)Digital Technology Limited ROOM 803, CHEVALIER HOUSE 45-51 CHATHAM ROAD SOUTH, TSIM SHA TSUI, KL Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen 518126 P.R. China Tel. 400-800-6106, 0755-2320 0050, 0755-2320 0090 Website: http://www.ntek.org.cn Report No.: S23041403402002 Version.1.3 Page 2 of 53 TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION ...................................................................................................................... 4 2 SUMMARY OF TEST RESULTS ......................................................................................................................... 5 3 FACILITIES AND ACCREDITATIONS ............................................................................................................. 6 3.1 FACILITIES..................................................................................................................................................... 6 3.2 LABORATORY ACCREDITATIONS AND LISTINGS ................................................................................. 6 3.3 MEASUREMENT UNCERTAINTY ............................................................................................................... 6 4 GENERAL DESCRIPTION OF EUT .................................................................................................................. 7 5 DESCRIPTION OF TEST MODES ..................................................................................................................... 9 6 SETUP OF EQUIPMENT UNDER TEST ......................................................................................................... 10 6.1 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ..................................................................... 10 6.2 SUPPORT EQUIPMENT ............................................................................................................................... 11 6.3 EQUIPMENTS LIST FOR ALL TEST ITEMS .............................................................................................. 12 7 TEST REQUIREMENTS .................................................................................................................................... 14 7.1 CONDUCTED EMISSIONS TEST ............................................................................................................... 14 7.1.1 Applicable Standard .................................................................................................................................. 14 7.1.2 Conformance Limit ................................................................................................................................... 14 7.1.3 Measuring Instruments ............................................................................................................................. 14 7.1.4 Test Configuration .................................................................................................................................... 14 7.1.5 Test Procedure ........................................................................................................................................... 14 7.1.6 Test Results ................................................................................................................................................ 15 7.2 RADIATED SPURIOUS EMISSION ............................................................................................................ 17 7.2.1 Applicable Standard .................................................................................................................................. 17 7.2.2 Conformance Limit ................................................................................................................................... 17 7.2.3 Measuring Instruments ............................................................................................................................. 18 7.2.4 Test Configuration .................................................................................................................................... 18 7.2.5 Test Procedure ........................................................................................................................................... 19 7.2.6 Test Results ................................................................................................................................................ 20 7.3 6DB BANDWIDTH ....................................................................................................................................... 26 7.3.1 Applicable Standard .................................................................................................................................. 26 7.3.2 Conformance Limit ................................................................................................................................... 26 7.3.3 Measuring Instruments ............................................................................................................................. 26 7.3.4 Test Setup .................................................................................................................................................. 26 7.3.5 Test Procedure ........................................................................................…

Text truncated - open the document above for the full version.