2BB78-F304DRemote Control

ITL‐304D Remote control operation instruction As shown in the figure: 1、1 button: to turn light ON or OFF. 2、2 button: Press the button for more than 0.7 seconds to start adjusting the brightness of the light, cycling between maximum and minimum brightness. The lights cycle every eight seconds. 3、3 button: to turn fan ON or OFF. 4、4 button: to set the fan speed to high. 5、5 button: to set the fan speed to medium. 6、6 button: to set the fan speed to low. 7、LED indicator: Press any key of the remote control, the indicator light will light up, and the remote control will issue instructions. Remote control pairing：Within 30 seconds after power is restored to the controller, press and hold the "3" key on the remote control transmitter for 5 seconds or until the light on the fan flashes. Test the light and fan functions using the remote transmitter to confirm that the learning process is complete. 7 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: - Reorient the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

COMPANY LETTERHEAD Covered Equipment Certification Attestation Letter 8/26/2024 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BB78-F304D ITL intelligence Lighting Technology Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. ITL intelligence Lighting Technology Co., Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: ZeHao Liu Title: Manager Company Name: ITL intelligence Lighting Technology Co., Ltd Date: 8/26/2024

COMPANY LETTERHEAD * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 8/26/2024 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2BB78-F304D FRN of applicant: 0034047662 Per section 2.911(d)(7) of the FCC rules, ITL intelligence Lighting Technology Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: UA INTERNATIONAL INC. FCC Registration Number (FRN): 0034047662 Physical U.S. Company Address: 5030 Boardwalk Dr Suite 818 Colorado Springs, COLORADO 80919, USA Contact Person: Jessica Zhong Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Agent Signed (if different from Applicant): Applicant Signed: Signed: Printed name: ZeHao Liu Title: Manager Signed: Printed name: Jessica Zhong Title: General Company Name: UA INTERNATIONAL INC. Date: 8/26/2024 Company Name: ITL intelligence Lighting Technology Co., Ltd Date: 8/26/2024

DATE: 8/26/2024 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Dongguan New Testing Centre Co., Ltd；1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ITL intelligence Lighting Technology Co., Ltd. Zhong nan hi-tech6#, Fuan west 1road, Dajiang Town,Taishan city, jiangmen city, Guangdong, China <Signature> Name：Ze Hao Liu Title：Manager Applicant Company：ITL intelligence Lighting Technology Co., Ltd

DATE：8/26/2024 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BB78-F304D Product Name: Remote control Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name:Ze Hao Liu Title:Manager Company: ITL intelligence Lighting Technology Co., Ltd Operation description Schematics and B O M Block diagram

Internal photos Model No. ITL‐304D Antenna

RF Exposure evaluation According to 447498 D04 Interim General RF Exposure Guidance v01 2.1.2 1-mW Test Exemption Per §1.1307(b)(3)(i)(A), a single RF source is exempt RF device (from the requirement to show data demonstrating compliance to RF exposure limits, as previously mentioned) if the available maximum time- averaged power is no more than 1 mW, regardless of separation distance. eirp = pt x gt = (EXd) 2 /30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m)---3m So pt = (EXd) 2 /30 x gt Field strength = 47.14 dBμV/m @3m Antenna gain=0dBi So EIRP=47.14-95.2=-48.06dBm 10^-4.806=0.0000156 mW<1 mW Then SAR evaluation is not required

Manufacture ：ZHONGSHAN MONITRONICS CO LTD MINYING ST ZHONGSHAN CIVIL SCIENCE & TECH PARK DONGMING NORTH RD ZHONGSHAN, GUANGDONG 528400 CHINA

Dongguan New Testing Centre Co., Ltd E-mail： [email protected] 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 FCC TEST REPORT Report No. .......................................: NTC-ER2407014 Applicant’s name ............................: ITL intelligence Lighting Technology Co., Ltd Address............................................: Zhong nan hi-tech6#, Fuan west 1road, Dajiang Town,Taishan city, jiangmen city, Guangdong, China DONGGUAN NEW TESTING CENTRE CO., LTD ◎Address: 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 Tel: +86-769-22212079 Web: http://www.ntc-cert.com E-mail: [email protected] Dongguan New Testing Centre Co., Ltd E-mail： [email protected] 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 Page 1 of 25 Report No.: NTC-ER2407014 TABLE OF CONTENTS 1. SUMMARY ............................................................................................................................................................... 4 1.1. TEST STANDARDS.......................................................................................................................................................... 4 1.2. TEST DESCRIPTION ........................................................................................................................................................ 4 1.3. TEST FACILITY .............................................................................................................................................................. 5 2. GENERAL INFORMATION .......................................................................................................................................... 6 2.1. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 6 2.2. GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 6 2.3. RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................................................ 6 2.4. MODIFICATIONS ........................................................................................................................................................... 6 2.5. EQUIPMENTS USED DURING THE TEST ................................................................................................................... 7 3. TEST CONDITIONS AND RESULTS .............................................................................................................................. 8 3.1. CONDUCTED EMISSION (AC MAIN) ................................................................................................................................. 8 3.2. RADIATED EMISSION ..................................................................................................................................................... 9 3.3. 20DB BANDWIDTH ..................................................................................................................................................... 18 3.4. DEACTIVATION TIME ................................................................................................................................................... 19 3.5. ANTENNA REQUIREMENT ............................................................................................................................................. 20 4. TEST SETUP PHOTOS OF THE EUT ........................................................................................................................... 21 5. EXTERNAL AND INTERNAL PHOTOS OF THE EUT ..................................................................................................... 22 Page 2 of 25 Report :NTC-ER2407014 TEST REPORT DECLARE Test Standard Used: FCC Rules and Regulations Part 15 Subpart C 15.231, ANSI C63.10:2020. We Declare: The equipment described above is tested by Dongguan New Testing Centre Co., Ltd and in the configuration tested the equipment complied with the standards specified above. The test results are contained in this test report and Dongguan New Testing Centre Co., Ltd is assumed of full responsibility for the accuracy and completeness of these tests. After test and evaluation, our opinion is that the equipment provided for test compliance with the requirement of the above FCC standards. Report No.: NTC-ER2407014 Date of Test: Jul.16, 2024 to Aug.06.2024 Date of Report: Aug.07.2024 Prepared By: Approved By: ________________ _____________________ Taylor Chen/Engineer Dave Gao/LAB Manager Note: This report applies to above tested sample only. This report shall not be reproduced in parts without written approval of Dongguan New Testing Centre Co., Ltd FCC ID : 2BB78-ITL-F304D Applicant : ITL intelligence Lighting Technology Co., Ltd Address : Zhong nan hi-tech6#, Fuan west 1road, Dajiang Town,Taishan city, jiangmen city, Guangdong, China Equipment under Test : Remote control Model/Type reference : ITL-304D List Model(s) N/A Trade Mark : ITL Manufacturer : ITL intelligence Lighting Technology Co., Ltd Address : Zhong nan hi-tech6#, Fuan west 1road, Dajiang Town,Taishan city, jiangmen city, Guangdong, China Test Laboratory Dongguan New Testing Centre Co., Ltd Address : 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 Page 3 of 25 Report :NTC-ER2407014 ** Modified History ** Version Description Issued Data Report No. Remark Version 1.0 Initial Test Report Release 2024-08-07 NTC-ER2407014 Dave Gao Page 4 of 25 Report :NTC-ER2407014 1. SUMMARY 1.1. Test Standards The tests were performed according to fo…

Text truncated - open the document above for the full version.

Set up photos Model No. ITL‐304D