2BB78-ITL-F433BRemote control

Product Name: Remote control Model Name：ITL-F433B FCC ID: 2BB78-ITL-F433B As shown in the figure: 1.Fan Off Button: Press to turn the light on or off. 2.Fan Speed Levels: Press the corresponding button to adjust the fan speed. 3.Anti-Theft Mode: Press this button to disable the fan controls and activate anti-theft mode. The motor will shut off, and regardless of whether the light is on or off, it will illuminate for 5 minutes, then turn off for 2 hours, followed by another 5 minutes of illumination. This cycle repeats. 4.Natural Wind Mode: After staying at level 1 for approximately 15 seconds, the fan speed increases to level 6 (ramp-up time about 5 seconds). At level 6, it remains for about 15 seconds before decreasing back to level 1 (ramp-down time about 5 seconds), repeating this cycle. 5.Fan Reversal: Press this button to reverse the fan’s direction of operation. 6Decrease Light Brightness: Press and hold to decrease the light brightness; short press for incremental reduction. 7.Increase Light Brightness: Press and hold to increase the light brightness; short press for incremental increase. 8.Light On/Off Switch: Turn the light on or off. 9.Timer: Set the fan to turn off after the specified duration. Remote Control Pairing: Within 30 seconds after the controller is restored to power, press and hold the Fan Off button on the remote transmitter for 5 seconds, or until the fan’s light flashes. Test the light and fan functions using the remote transmitter to confirm the pairing process is complete. FCC statement This device complies with Part 15 of the FCC rules. Operation is subject to thefollowing two conditions: 1) This device may not cause interference. 2) This device must accept any interference, including interference that may causeundesired operation of the device. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation, lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

ITL intelligence Lighting Technology Co., Ltd Covered Equipment Certification Attestation Letter 12/11/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.:Programming the remote control FCC ID: 2BB78-ITL-F433B Dongguan Sapin Electronic Technology Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Dongguan Sapin Electronic Technology Co., Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Dongguan Sapin Electronic Technology Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: Liu ze hao Title: General Manager Company Name: ITL intelligence Lighting Technology Co., Ltd Date: 12/10/2025

ITL intelligence Lighting Technology Co., Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 12/12/2025 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Programming the remote control FCC ID: 2BB78-ITL-F433B FRN of applicant: 0034047662 Per section 2.911(d)(7) of the FCC rules, [ITL intelligence Lighting Technology Co., Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: TTS MARKET INC. FCC Registration Number (FRN): 0036806057 Physical U.S. Company Address: 1178 Broadway Ste 324, New York, NY 10001, USA Contact Person: Maverick Lim Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Liu ze hao Title: General Manager Company Name: ITL intelligence Lighting Technology Co., Ltd Date: 12/12/2025 Agent Signed (if different from Applicant): Signed: Printed name: Maverick Lim Title: Manager Company Name: TTS MARKET INC, Date: 12/12/2025 ITL intelligence Lighting Technology Co., Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process.

DATE 2025.12.10 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BB78-ITL-F433B Product Name: remote control Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description  BOM These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name ：ZeHao Liu Title：General Manager Company：ITL intelligence Lighting Technology Co., Ltd

DATE: 2025.12.10 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Age nt On our behalf, I appoint Dongguan New Testing Centre Co., Ltd; 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ITL intelligence Lighting Technology Co., Ltd；3&4rd Floor,Dazhongnan IndustrialPark,No.4 Huiyuan East Road,Huihuan Subdistrit, HUIZHOU,Guangdong 51600 (Applicant Name and address) <Signature> Name : ZeHao Liu Title: General Manager Applicant Company: ITL intelligence Lighting Technology Co., Ltd

Date 2025.12.10 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name: ZeHao Liu Title: General Manager Applicant Company: ITL intelligence Lighting Technology Co., Ltd

Remote control Model: ITL-F433B FCC ID: 2BB78-ITL-F433B

Antenna

RF Exposure evaluation According to 447498 D04 Interim General RF Exposure Guidance v01 2.1.2 1-mW Test Exemption Per §1.1307(b)(3)(i)(A), a single RF source is exempt RF device (from the requirement to show data demonstrating compliance to RF exposure limits, as previously mentioned) if the available maximum time- averaged power is no more than 1 mW, regardless of separation distance. eirp = pt x gt = (EXd) 2 /30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m)---3m So pt = (EXd) 2 /30 x gt Field strength = 60.61dBμV/m @3m Antenna gain=3dBi So EIRP=60.61-95.2=-34.59dBm 10^-34.83=0.0003 mW<1 mW Then SAR evaluation is not required

PAC101 PAC102 COC1 PAC202 PAC201 COC2 PAC301 PAC302 COC3 PAC402 PAC401 COC4 PAC502 PAC501 COC5 PAC602 PAC601 COC6 PAC702 PAC701 COC7 PAC802 PAC801 COC8 PAC902 PAC901 COC9 PAC1002 PAC1001 COC10 PAC1102 PAC1101 COC11 PAC1501 PAC1502 COC15 PAD102 PAD101 COD1 PAK5101 PAK5102 PAK5100 COK51 PAK5301 PAK5302 PAK5300 COK53 PAK5901 PAK5902 PAK5900 COK59 PAK6001 PAK6002 PAK6000 COK60 PAK6101 PAK6102 PAK6100 COK61 PAK6601 PAK6602 PAK6600 COK66 PAK6701 PAK6702 PAK6700 COK67 PAK7201 PAK7202 PAK7200 COK72 PAK7301 PAK7302 PAK7300 COK73 PAK7401 PAK7402 PAK7400 COK74 PAK7701 PAK7702 PAK7700 COK77 PAK7801 PAK7802 PAK7800 COK78 PAK7901 PAK7902 PAK7900 COK79 PAK8101 PAK8102 PAK8100 COK81 PAK8201 PAK8202 PAK8200 COK82 PAK8301 PAK8302 PAK8300 COK83 PAL102 PAL101 COL1 PAL202 PAL201 COL2 PAL302 PAL301 COL3 PALED102 PALED101 COLED1 PAR102 PAR101 COR1 PAR202 PAR201 COR2 PAR302 PAR301 COR3 PAU104 PAU101 PAU103 PAU106 PAU102 PAU105 COU1 PAU204 PAU2016 PAU208 PAU2015 PAU2014 PAU2013 PAU2012 PAU2011 PAU2010 PAU209 PAU207 PAU206 PAU205 PAU202 PAU201 PAU203 COU2 PAU301 PAU303 PAU302 COU3 PAY104 PAY103 PAY102 PAY101 COY1 PAD102 PAR201 PAR302 PAU2012 PAU2013 PAC101 PAC201 PAC301 PAC401 PAC501 PAC601 PAC801 PAC901 PAC1001 PAC1101 PAC1502 PAR301 PAU102 PAU2015 PAU301 PAY102 PAY104 PAC1102 PAL202 PAC302 PAD101 PAU302 PAC502 PAU106 PAY101 PAC602 PAU101 PAY103 PAC701 PAL102 PAU103 PAC702 PAL301 PAC1002 PAL201 PAL302 PALED101 PAR101 PALED102 PAU2014 PAR202 PAU104 PAU201 PAK5302 PAK6102 PAK7402 PAK7902 PAK8302 PAU202 PAK6002 PAK6702 PAK7302 PAK7802 PAK8202 PAU203 PAK5102 PAK5902 PAK6602 PAK7202 PAK7702 PAK8102 PAU204 PAK8101 PAK8201 PAK8301 PAU205 PAK7701 PAK7801 PAK7901 PAU206 PAK7201 PAK7301 PAK7401 PAU207 PAK6601 PAK6701 PAU208 PAK5901 PAK6001 PAK6101 PAU209 PAK5101 PAK5301 PAU2011 PAC102 PAC202 PAC402 PAC802 PAC902 PAC1501 PAL101 PAR102 PAU105 PAU2010 PAU303

Page 1 / 28 No.:NTC-ER2508023 FCC TEST REPORT Report No..................................... : NTC-ER2511038 Applicant’s name ......................... : ITL intelligence Lighting Technology Co., Ltd Addre ss ....................................... : 3&4rd Floor,Dazhongnan IndustrialPark,No.4 Huiyuan East Road,Huihuan Subdistrit, HUIZHOU,Guangdong 51600 DONGGUAN NEW TESTING CENTRE CO., LTD ◎Address: 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 Tel: +86-769-22212079 Web: http://www.ntc-cert.com E-mail: [email protected] Page 1 / 28 No.:NTC-ER2511038 TABLE OF CONTENTS 1. SUMMARY ........................................................................................................................................ 4 1.1. Test Standards............................................................................................................................ 4 1.2. Test Description ......................................................................................................................... 4 2. Test Facility ....................................................................................................................................... 5 3. GENERAL INFORMATION ................................................................................................................... 6 3.1. Environmental conditions ........................................................................................................... 6 3.2. General Description of EUT ......................................................................................................... 6 3.3. Related Submittal(s) / Grant (s) ................................................................................................... 6 3.4. Modifications ............................................................................................................................. 6 3.5. Equipments Used During The Test ............................................................................................... 7 4. TEST CONDITIONS AND RESULTS........................................................................................................ 8 4.1. Conducted Emission (AC Main) .................................................................................................... 8 4.2. Radiated Emission ...................................................................................................................... 9 4.3. 20dB Bandwidth ....................................................................................................................... 19 4.4. Deactivation Time..................................................................................................................... 20 4.5. Antenna Requirement............................................................................................................... 21 5. Test Setup Photos of the EUT........................................................................................................... 22 6. External and Internal Photos of the EUT........................................................................................... 23 Dongguan New Testing Centre Co., Ltd E-mail： [email protected] 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 Page 2 / 28 No.:NTC-ER2511038 TEST REPORT DECLARE Test Standard Used: FCC Rules and Regulations Part 15 Subpart C 15.231, ANSI C63.10:2020. We Declare: The equipment described above is tested by Dongguan New Testing Centre Co., Ltd and in the configuration tested the equipment complied with the standards specified above. The test results are contained in this test report and Dongguan New Testing Centre Co., Ltd is assumed of full responsibility for the accuracy and completeness of these tests. After test and evaluation, our opinion is that the equipment provided for test compliance with the requirement of the above FCC standards. Report No.: NTC-ER2511038 Date of Test: Nov.27,2025 to Nov.27,2025 Date of Report: Dec.12,2025 Prepared By: Approved By: ___________________ ______________________ Taylor Chen/Engineer Dave Gao/LAB Manager Note: This report applies to above tested sample only. This report shall not be reproduced in parts without written approval of Dongguan New Testing Centre Co., Ltd FCC ID : 2BB78-ITL-F433B Applicant : ITL intelligence Lighting Technology Co., Ltd Address : 3&4rd Floor,Dazhongnan IndustrialPark,No.4 Huiyuan East Road,Huihuan Subdistrit, HUIZHOU,Guangdong 51600 Equipment under Test : Remote control Model/Type reference : ITL-F433B List Model(s) N/A Trade Mark : ITL Manufacturer : ITL intelligence Lighting Technology Co., Ltd Address : 3&4rd Floor,Dazhongnan IndustrialPark,No.4 Huiyuan East Road,Huihuan Subdistrit, HUIZHOU,Guangdong 51600 Test Laboratory Dongguan New Testing Centre Co., Ltd CAB identifier : CN1264 Address : 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 Dongguan New Testing Centre Co., Ltd E-mail： [email protected] 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 Page 3 / 28 No.:NTC-ER2511038 ** Modified History ** Version Description Issued Data Report No. Remark Version 1.0 Initial Test Report Release 2025-12-12 NTC-ER2511038 Dave Gao Dongguan New Testing Centre Co., Ltd E-mail： [email protected] 1F & 3F, No. 1 the 1st North Industry Road Songshan Lake Science & Technology Park Dongguan, People’s Republic of China 523808 Page 4 / 28 No.:NTC-ER2511038 1. SUMMARY 1.1. Test Standards The tests were performed according to following standards: FCC Rules Part 15.231: Periodic operation in the band 40.66-40.70 MHz and above 70 MHz. ANSI C63.10:2020 : American National Standard for Testing Unlicensed Wireless Devices 1.2. Test Description FCC and IC Requirem…

Text truncated - open the document above for the full version.