2BBCYUHG-01Two way radio

UHG-01 Preface Thank you for purchasing our GMRS Portable Two Way Radio. This easy to use radio will always offer you reliable, clear and high efficiency communication services. Please read this manual carefully before using this radio, the information presented herein will help you to find the maximum performance, operating method and maintenance of your radio. Attention This radio complieswith IEEE and ICNIRP exposure limits for occupational/controlled RF exposure emvironment at operating duty factors of up to 50% and is authorized by the FCC for Occupational Use Only. An appropriate warning lable is affixed to all units. In order to comply with RF exposure requirements, a minimum distance of 2.5 cm must be maintained when held-to-face, and body-worn operations are restricted to the approved original acessories (belt clip), a minimum distance of 0 cm. Do not use this device when antenna shows obvious damages. FCC Part 15.21 Warning Statement The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. Replacement of any transmitter component (crystal, semiconductor, etc) not authorized by the FCC equipment authorization for this radio could violate FCC rules. FCC Part 15.19 Warning Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) this device must accept any interference including received interference that may cause undesired operation. WARNING MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Part 15.105(b) Warning Statement CONTENTS SAFETY INFORMATION BATTERY INFORMATION PRODUCT CHECK RADIO OVERVIEW PREPARATION Install & Remove the Battery Install & Remove the Antenna Install & Remove the Belt Clip Install & Remove the Accessory BASIC OPERATION Power On/Off Adjust the Volume Select a Channel Transmit Receive Voice Announcement Output Power switching Channel broadcast Squelch level Cancel Squelch Scanning Emergency alarm Voice control switch(VOX) Battery level speech VOX voice control delay CALL bell Companding function Voice scrambling Busy channel lock QT/DQT Wide/narrow bandwidth selection Transmission time limit The battery saving function Battery low voltage alarm function Tail sound selection Strengthen the decoding function SPECIFICATION Factory set frequency and QT/DQT 01 02 05 06 07 07 07 07 08 09 09 09 09 09 09 10 10 10 11 11 11 12 12 12 12 13 13 13 13 14 14 14 15 15 15 16 17 18 SAFETY INFORMATION Please read the following safety information in order to offer you security and high efficiency during operation. Please turn off the radio before entering an inflammable and explosive area. Do not replace the battery or charging when you are in an inflam- mable and explosive area. Please turn off the radio when you are close to the blast area or detonator zone. Do not use any radio which has a damaged antenna. It may cause a minor burn when the damaged antenna touches your skins. Do not attempt to dismantle the radio unless professional technical person. To avoid the problems which caused by EMI and EMC, turn off your radios in any places where posted notices “Please turn off your radios”. For example, the hospital or other health care places. Turn off your radio before boarding an aircraft. Any use of the radio must be in accordance with airline regulations or flight crew’s instructions. If the vehicles have carried with an air bag, do not put your radios within the air bag expand coverage. Do not expose the radio to direct sunlight over a long time, nor place it close to the heating equipment. Do not place the radio in any excessively dusty, humid or wet place, nor an unstable surface. When the portable radio is transmitting, please hold the radio in a vertical position and speak to the Microphone. If you carry a radio on your body, please keep the antenna away from your body 2.5cm at least when the radio is transmitting. BATTERY INFORMATION Initial Use New batteries are not charged fully in the factory. Please charge it before using. In general, the battery should charge 4 hours at initial use. The maximum battery capacity and performance is achieved after three times fully battery charge-discharge cycle. When the battery power runs out, please recharge the battery or replace one. Applicable Battery Pack Please only use the battery which specified by the manufacturer. Unauthorized batteries may cause the failure of Ex-protection or bodily injury and property damages. Safety Information 1)Do not throw the battery into fire! 2)Do not abandon the battery as the household garbage, it should be recycled and disposed correctly. 3)Never attempt to disassemble the battery pack. Notices…

Text truncated - open the document above for the full version.

Lisheng Communication Co., Ltd. 5#, Chongxiang St., Econ. & Tech. Area, Quanzhou, Fujian, China Agent Authorization Company: Lisheng Communications Co., Ltd. Address: 5#, Chongxiang St., Econ. & Tech. Area, Quanzhou, Fujian, China Product Name: Two way radio Model Number(s): UHG-01 Product Description: Two way radio We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2023-06-29 Name: HanYang Qiu Company: Lisheng Communications Co., Ltd.

Declaration on model difference We the undersigned hereby confirm that any of our production units bearing the following model numbers are identical in circuitry and electrical, mechanical and physical construction; the only differences are as below for trading purpose. The model names & cover designs are different; Charger with the same PCB & different shell; Battery with different shell, same PCB & cells Product Name Two way radio Brand Name / Model MOHANTON / UHG-01, UHG-02, UHG-03, UHG-04 Manufacturer Information： Company Lisheng Communication Co., Ltd. Address 5#, Chongxiang St., Econ. & Tech. Area, Quanzhou, Fujian, China Name/Title HanYang Qiu E-mail [email protected] Tel. No. 18905969228 Fax No. Signature / stamp Date: 2023-07-03

Lisheng Communication Co., Ltd. 5#, Chongxiang St., Econ. & Tech. Area, Quanzhou, Fujian, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date:2023-06-27 Subject; Request for Confidentiality FCC ID: 2BBCYUHG-01 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely Contact person: HanYang Qiu

Report No.: AGC15733230601AP02 Page 1 of 4 EXTERNAL PHOTOS All VIEW OF EUT TOP VIEW OF EUT Antenna Report No.: AGC15733230601AP02 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC15733230601AP02 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC15733230601AP02 Page 4 of 4 RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 40mm&40mm FCC ID: 2BBCYUHG-01

Report No.: AGC15733230601AP01 Page 1 of 6 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC15733230601AP01 Page 2 of 6 OPEN VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 1) Report No.: AGC15733230601AP01 Page 3 of 6 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) Report No.: AGC15733230601AP01 Page 4 of 6 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) Report No.: AGC15733230601AP01 Page 5 of 6 INTERNAL VIEW OF EUT (FIGURE 6) INTERNAL VIEW OF EUT (FIGURE 7) Report No.: AGC15733230601AP01 Page 6 of 6 INTERNAL VIEW OF EUT (FIGURE 8) INTERNAL VIEW OF EUT (FIGURE 9) ****************************************End of Report*************************************

Page 1 of 18 CALIBRATION DATA PROBE CALIBRATION DATA Page 2 of 18 Page 3 of 18 Page 4 of 18 Page 5 of 18 Page 6 of 18 Page 7 of 18 Page 8 of 18 Page 9 of 18 Page 10 of 18 DAE CALIBRATION DATA Page 11 of 18 Page 12 of 18 Page 13 of 18 DIPOLE CALIBRATION DATA Page 14 of 18 Page 15 of 18 Page 16 of 18 Page 17 of 18 Page 18 of 18

Page 1 of 38 SAR Test Report Report No.: AGC15733230601FH01 FCC ID : 2BBCYUHG-01 PRODUCT DESIGNATION : Two way radio BRAND NAME : MOHANTON MODEL NAME : UHG-01, UHG-02, UHG-03, UHG-04 APPLICANT : Lisheng Communication Co., Ltd. DATE OF ISSUE : Jun. 27, 2023 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC15733230601FH01 Page 2 of 38 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 27, 2023 Valid Initial Release Report No.: AGC15733230601FH01 Page 3 of 38 Test Report Applicant Name Lisheng Communication Co., Ltd. Applicant Address 5#, Chongxiang St., Econ. & Tech. Area, Quanzhou, Fujian, China Manufacturer Name Lisheng Communication Co., Ltd. Manufacturer Address 5#, Chongxiang St., Econ. & Tech. Area, Quanzhou, Fujian, China Factory Name Lisheng Communication Co., Ltd. Factory Address 5#, Chongxiang St., Econ. & Tech. Area, Quanzhou, Fujian, China Product Designation Two way radio Brand Name MOHANTON Model Name UHG-01 Series Models UHG-02, UHG-03, UHG-04 Declaration of Difference The model names & cover designs are different; Charger with the same PCB & different shell; Battery with different shell, same PCB & cells EUT Voltage DC7.4 V Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 Date of receipt of test item Jun. 06, 2023 Test Date Jun. 20, 2023 Report Template AGCRT- US -PTT/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Bibo Zhang (Project Engineer) Jun. 20, 2023 Reviewed By Calvin Liu (Reviewer) Jun. 27, 2023 Approved By Max Zhang (Authorized Officer) Jun. 27, 2023 Report No.: AGC15733230601FH01 Page 4 of 38 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 7 3.1. THE DASY5 SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................... 7 3.2. DASY5 E-FIELD PROBE ................................................................................................................................. 8 3.3. DATA ACQUISITION ELECTRONICS DESCRIPTION ............................................................................................... 8 3.4. ROBOT .......................................................................................................................................................... 9 3.5. LIGHT BEAM UNIT .......................................................................................................................................... 9 3.6. DEVICE HOLDER .......................................................................................................................................... 10 3.7. MEASUREMENT SERVER ............................................................................................................................... 10 3.8. PHANTOM ................................................................................................................................................. 11 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 12 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 12 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 13 5. TISSUE SIMULATING LIQUID ....................................................................................................................... 15 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 15 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 15 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 16 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 17 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 17 7. EUT TEST POSITION ...................................................................................................................................... 19 7.1. BODY WORN POSITION ................................................................................................................................ 19 8. SAR EXPOSURE LIMITS ............................................................................................................................... 20 9. TEST FACILITY .............................................................................................................................................. 21 10. TEST EQUIPMENT LIST .............................................................................................................................. 22 11. MEASUREMENT UNCERTAINTY ................................................................................................................ 23 12. POWER MEASUREMENT .........................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 40 FCC Test Report Report No.: AGC15733230601FE10 FCC ID : 2BBCYUHG-01 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Two way radio BRAND NAME : MOHANTON MODEL NAME : UHG-01, UHG-02, UHG-03, UHG-04 APPLICANT : Lisheng Communication Co., Ltd. DATE OF ISSUE : Jun. 27, 2023 STANDARD(S) : FCC Part 95 Rules REPORT VERSION : V 1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC15733230601FE10 Page 2 of 40 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 27, 2023 Valid Initial Release Report No.: AGC15733230601FE10 Page 3 of 40 TABLE OF CONTENTS 1. GENERAL INFORMATION .............................................................................................................................. 5 2. PRODUCT INFORMATION .............................................................................................................................. 6 2.1 PRODUCT TECHNICAL DESCRIPTION ................................................................................................ 6 2.2 TEST FREQUENCY LIST ........................................................................................................................ 7 2.3 RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................. 8 2.4 TEST METHODOLOGY .......................................................................................................................... 8 2.5 CALCULATION OF EMISSION INDICATORS ........................................................................................ 8 2.6 SPECIAL ACCESSORIES ....................................................................................................................... 8 2.7 EQUIPMENT MODIFICATIONS .............................................................................................................. 8 2.8 ANTENNA REQUIREMENT .................................................................................................................... 9 3. TEST ENVIRONMENT ................................................................................................................................... 10 3.1 ADDRESS OF THE TEST LABORATORY ............................................................................................ 10 3.2 TEST FACILITY ..................................................................................................................................... 10 3.3 ENVIRONMENTAL CONDITIONS......................................................................................................... 11 3.4 MEASUREMENT UNCERTAINTY ........................................................................................................ 11 3.5 LIST OF EQUIPMENTS USED ............................................................................................................. 12 4. SYSTEM TEST CONFIGURATION ................................................................................................................ 13 4.1 EUT CONFIGURATION ......................................................................................................................... 13 4.2 EUT EXERCISE ..................................................................................................................................... 13 4.3 CONFIGURATION OF TESTED SYSTEM ............................................................................................ 13 4.4 EQUIPMENT USED IN TESTED SYSTEM........................................................................................... 13 4.5 SUMMARY OF TEST RESULTS ........................................................................................................... 14 5. DESCRIPTION OF TEST MODES ................................................................................................................. 15 6. FREQUENCY STABILITY .............................................................................................................................. 16 6.1 PROVISIONS APPLICABLE .................................................................................................................. 16 6.2 MEASUREMENT PROCEDURE ........................................................................................................... 16 6.3 MEASUREMENT SETUP ...................................................................................................................... 16 6.4 MEASUREMENT RESULTS.................................................................................................................. 17 7. EMISSION BANDWIDTH ............................................................................................................................... 18 7.1 PROVISIONS APPLICABLE .................................................................................................................. 18 7.2 MEASUREMENT PROCEDURE ........................................................................................................... 18 7.3 MEASUREMENT SETUP ...................................................................................................................... 18 7.4 MEASUREMENT RESULTS.................................................................................................................. 19 8. SPURIOUS RATIATED EMISSION ................................................................................................................. 20 8.1 PROVISIONS APPLICABLE .................................................................................................................. 20 Report No.: AGC15733230601FE10 Page 4 of 40 8.2 MEASUREMENT PROCEDURE ........................................................................................................... 20 8.3 MEASUREMENT SETUP ...................................................................................................................... 21 8.4 MEASUREMENT RESULTS..............…

Text truncated - open the document above for the full version.

Report No.: AGC15733230601AP01 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC15733230601AP01 Page 2 of 2 RF CONDUCTED TEST SETUP ****************************************End of Report*************************************