2BBZS-B113A01501Bluetooth Control Module

Technical requirements Product mode:B113A-015-1; 1.Controller operating voltage: DC8V-60V, withstand voltage 50Hz/pulse DC peak 5ov; standby current s25mA storage temperature -30° 2.Housing material ABS or PA6,encapsulant material epoxy resin no scratches or dents on component surfaces, no sagging of encapsulantmaterial no contamination of connectors and electronic components; 3.Dimensions without tolerance shall comply with QRT J12-20074. 4.When connecting the battery SAE interface to the machine, the Bluetooth control module should be powered off and not working; power consumption during disconnection <500uA; 5.Test whether automatic power-off time is 24 hours -the machine is in power-off state, press 5S> one-key switch 1s,enter standby mode, one-key indicator green light starts flashing,interval time is7 seconds on/1 second off. In standby mode, test voltage at both ends of gasoline solenoid valve and gas solenoid valve, neither type of solenoid valve allows energized condition;if no generator start operation (including hand pull start)within 24 hours,machine Bluetooth module automatically powers off; 6.When the module is in standby mode, the mobile APP canc1o the machine's Bluetooth and after successful connection, the Bluetooth indicator light on the display will light up;7.In standby mode: Measuring DC current with a multimeter at 25mA; 8.Regardless of whether the battery is removed, if the machine is operating normally,it should be able to stop by pressing APP (the charging module must power the Bluetooth module); 9. Any normal or abnormal shutdown unrelated to Bluetooth module control(e.g, LPG gas depleted, gasoline exhausted, low oil level, noignition) should cause theBluetooth module to enter standby mode after shutdown; one-button indicator green light starts flashing with aninterval of 7 seconds on /1 second off; 10.Each time entering standby mode from power-off.regardless of the position of the air door, the carburetor air gate should automatically open to full open position;(Note: It does not automatically open when the Bluetooth module is powered on.In battery-free conditions,manuallyoperate the air gate lever by hand,and after manual start, the air gate cannot open automatically!) Total 1 page Page 1 pattern marking weight proportion B Remarks weight Approver Bid reviewer ReviewerProofreaderPrepared by Specification document NO code Tag Name unit usage Product Code ABS Mode Document No.: B113A-015-1 - PD - A/0 connector 5557-6A connector blue 5557-2A connector 5557-6A connector 5557-4A connector 5557-12A connector 5557-10A connector Mark the location 11. Forced Standby Mode Exit Test - In standby mode, press and hold the power button for more than 5 seconds, then release; after releasing, exit standby mode and enter power-off mode. The mobile APP connects via Bluetooth for; The mobile APP connects via Bluetooth for startup, and due to the module entering power-off mode, the APP will display a Bluetooth signal loss prompt; 12.Bluetooth remote control distance test and other routine testing items shall comply with company standard requirements: add 50%rated load, send Bluetooth signal at 8 angles 1 angle from top, clear distance, start and stop both no less than 30m; 13.High concentration shutdown remote control prohibits testing -after a high concentration alarm for the CO module or an abnormal shutdown alarm for the sensor of the CO module, the module will stop the ongoing remote start and the remote start function is prohibited; The user cannot slide the STOP of the mobile phone APP for remote shutdown,even if the blue tooth module is powered off (disconnect the battery, Re-charge of battery switching and other actions also maintains the remote control start ineffective, and it is necessary for the person to be close to the machine hand-start or one-click electric start successfully to unload the APPremote control lock function,and the mobile APP's start function returns to normal; 14.APP functions refer to the Bluetooth control system requirements for RunTong open-frame generator sets. )&&&:$51,1*This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna.--Increase the separation between the device and receiver.--Connect the device into an outlet on a circuit different from that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician for helpChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipmentThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation (3) FCC ID 2BBZS-B113A01501 ,&:$51,1* This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference.(2) This device must accept any interference, including interference that may cause undesired operation of the device ADVERTENCIA IC Cet appareil conti…

Text truncated - open the document above for the full version.

3/17 Fed Auth 7435 Colu USA AT T FCC Cho equi rece Ch o the d (as a prod Ch o equi softw assi suc c and Sig n Prin Titl e Com Date Co 7/2026 eral Comm u horization a 5 Oakland M umbia, MD 2 A TN.: Review C ID: 2BBZS ongqing Jan ipment for w eiving an eq Note: If any of t h include ongqing Jan date of the f a specificall ducing “cove ongqing Jan ipment for w ware produc gnees, inclu cessors and KDB 98644 ned: ted name: X e: Engineer mpany Name e: 3/17/2026 Chongq overed Eq unications C nd Evaluatio Mills Road 21046 wing Engin S-B113A015 xin Intellige which autho quipment au the equipm he entities id an explanat xin Intellige filing of the ly named en ered” equip xin Intellig e which autho ced or prov uding equip d assignees 46 D01 Cov Xingjian Hua e: Chongqin 6 qing Janxin quipment Commission on Division neer 501 ent Instrume orization is s thorization ent for whi c dentified on tion on why ent Instrume application ntity or any ment. ent Instrume orization is s ided by Ka pment with in s) cybersecu vered Equip ang ng Janxin In Intelligent I t Certifica n ents Co., Ltd sought is no pursuant to ch the applic n the current y the equipm ents Co., Ltd , the applica of its subsid ents Co., Ltd sought does spersky Lab ntegrated K urity or anti- ment Guid a ntelligent Ins Instruments ation Attes d. (“the appl t “covered” section 2. 9 cant seeks a t Covered L ment is not “ d. (“the appl ant is not ide diaries or af d. (“the appl s not include b, Inc. or an Kaspersky L virus softwa ance section struments C s Co., Ltd. station Le icant”) certi equipment 903 of the F authorizatio List, the app covered” eq icant”) certi entified on t ffiliates) as a icant”) certi e cybersecu ny of its succ Lab, Inc. (or are pursuan n B(2a). Co., Ltd. etter fies that the prohibited f CC rules. on is produc plicant shoul quipment. fies that, a s the Covered an entity fies that th e urity or anti- cessors and r any of its nt to DA-24- e from ced by ld s of d List e -virus d 886

Marc Fede Auth 7345 Colu On o C, 1s Villa to ac that certi f defin labe For i beha for c Co. Dist <Sig n Name Title： Applic ch 17, 2026 eral Commu horization & 5 Oakland M umbia, Mary our behalf, I st Floor, Blo ge, Nansha ct as our age submitted d fication is so ned in the Fe l identical to instances w alf, I acknow certification, , Ltd./ Xi trict, Cho nature>： e：Xingjian Engineer cant Compa 6 unications C Evaluation D Mills Road land 21046 appoint She ock B, Jun X n District, S ent in the pr documents p ought. I also ederal Comm o that submit where our au wledge that still resides anfeng I n ongqing, Huang any：Chong ommission Division Author i enzhen Time Xiang Da Bui henzhen, C reparation of properly desc o certify that munications tted for appr uthorized ag all responsi with C h o n ndustrial China gqing Janxi ity to Act as eway Testin ilding, Zhon hina (Name f this applica cribe the de each unit m s Commissio roval with th ent signs th ibility for com ngqing Ja Zone, Xi n Intelligent s Agent ng Laborator gshan Park of Agent co ation for equ evice or syst manufactured on’s regulatio his applicatio he applicatio mplying with anxin Inte anfengTo t Instrumen ries/ Zone C Road West ompany nam uipment cert em for which d, imported ons will hav on. on for certific h the terms elligent In own, Jian ts Co., Ltd. C, 1st Floor, t, Tong Le me and addr tification. I c h equipme n or marketed ve affixed to cation on ou and conditio nstrumen ngjin Zone ress) ertify t d, as it a ur ons ts

March 17, 2026 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BBZS-B113A01501 Product Name: Bluetooth Control Module Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>： Name：Xingjian Huang Title：Engineer Applicant Company：Chongqing Janxin Intelligent Instruments Co., Ltd.

Model: B113A-015-1 Input: 8V 60V 7A MAX Name: FCCID:2BBZS-B113A01501 IC:35314-B153A0151 Bluetooth Control Module

Label Location

RF Exposure evaluation FCC ID: 2BBZS-B113A01501 According to 447498 D04 Interim General RF Exposure Guidance v01 ERP=Peak Power + Antenna Gain -2.15=-2.36+4.13-2.15=-0.38dBm=0.92mW < 2.8mW (Worst case recorded) Then SAR evaluation is not required

Report No.: TW2601030-02E Applicant: Chongqing Janxin Intelligent Instruments Co., Ltd. Product: Bluetooth Control Module Model No.: B113A-015-1 Trademark: PAEDATOR Test Standards: FCC Part 15.247 Test Result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10, FCC Part 15.247 for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: March 11, 2026 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No.: TW2601030-02E Page 2 of 63 Date: 2026-03-11 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. ISED —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of ISED for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 CAB identifier: CN0033 FCC Designation Number: CN1251 Report No.: TW2601030-02E Page 3 of 63 Date: 2026-03-11 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT ........................................................................................... 4 1.4 Submitted Sample.............................................................................................. 4 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty............................................................................................... 5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test...................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating Condition.................................................................................... 9 5.5 Conducted Emission Limit................................................................................... 9 5.6 Test Result...................................................................................................... 9 6.0 Radiated Emission test...................................................................................... 12 6.1 Test Method and Test Procedure............................................................................ 12 6.2 Configuration of the EUT......…

Text truncated - open the document above for the full version.

2.4G胶棒天线 型号: BW2.4GJWX156-13KK 描述: 2.4G胶棒天线 SMA内螺内孔接口 特性: 2400-2500MHz全频段覆盖 SMA内螺内孔接口 结构：可折叠，360º全向辐射 尺寸：156mm x ⌀13mm 符合 RoHS & REACH 规定 天线规格书 蝙蝠无线 BAT WIRELESS 1 / 13 Antenna Datasheet www.batwireless.cn 目 录 July-21-2025-A01 2 / 13 蝙蝠无线 BAT WIRELESS www.batwireless.cn 1. 产品描述3 2. 产品规格4 3. 实物图5 4. 尺寸图6 5. 测试设备7-8 6. 性能数据9-10 6.1 电压驻波比9 6.2 回波损耗9 6.3 增益10 6.4 效率10 6.5 天线增益与效率10 7. 辐射模式图11-12 7.1 2D辐射模式图11 7.2 3D辐射模式图12 法律声明： 本着为用户提供更好服务的原则，深圳市蝙蝠无线技术有限公司（下称“蝙蝠无线”）在本手册中将尽可能地为用户 呈现详 实、准确的产品信息。但介于本手册的内容具有一定的时效性，蝙蝠无线不能完全保证该文档在任何时段的时效性与适 用性。 蝙蝠无线有权在没有通知的情况下对本手册上的内容进行更新，恕不另行通知。为了得到最新版本的信息，请尊敬的 用户定时 访问蝙蝠无线官方网站或者与蝙蝠无线工作人员联系。感谢您的包容与支持！ 版权声明：本产品手册所有内容（包括文字、图表、标识及设计）均受著作权法及国际版权条约保护。任何单位和个人未经我 司事先书面授权，不得以任何形式（包括电子、机械、影印等）复制、修改、传播、分发和使用本手册全部或部分内容。侵权 者将承担相应法律责任。保留所有权利。 商标声明：本手册中出现涉及到蝙蝠无线商品名称及企业标识均属我公司（含关联公司）合法所有。严禁任何未经授权的使用、 复制或仿冒行为。手册引用的第三方商标权利归相应权利人所有，其使用仅作说明目的，不构成商业关联或授权暗示。我公司 保留追究侵权法律责任的一切权利。 免责声明：本手册所载产品信息仅供参考，产品实际性能可能因使用环境、配置差异而有所不同。本公司不对手册内容的准确 性、完整性或适用性作任何明示或默示保证，亦不承担因使用或无法使用本手册内容而产生的直接或间接损失。用户应自行评 估产品适用性并遵循实际操作规范。最终解释权归本公司所有。 经典应用场景： 智能家居/Wi-Fi扩展：增强无线网络覆盖 安防监控：保障户外摄像头信号稳定传输 工业物联网（IIoT）：用于设备间的无线数据交互 无人机通信：提供稳定的远程控制与高清图传 蝙蝠无线BW2.4GJWX156-13KK是一款高性能全向天线，同时支持 2.4GHz 频段，适用于Wi-Fi、无人机图传、工业控制 等场景。采用优质塑胶外壳，可折叠，具备出色的信号接收与发射能力，为设备连接提供稳定可靠的支持。其紧凑轻便的胶棒 造型设计，易于安装和运输携带。 1. 产品描述 / Description www.batwireless.cn July-21-2025-A01 蝙蝠无线提供定制化服务以优化您的设备，我们拥有成熟的研发团队，能够迅速响应以满足您的需求。如果您有任何要 求，请联系我们的销售和 FAE。 3 / 13 零件编号说明 BW 公司 / Company 蝙蝠无线 / Bat Wireless 2.4G 频段 / Frequency 2400-2500MHz 5150-5850MHz J 名称 / Name 胶棒 / Rubber Antenna W 类型 / Type 外置 / External X 常数 / Constant X / X 156-13 尺寸 / Dimensions 156 x ⌀13mm / 156 x ⌀13mm K 类型 / Type 可折叠 K 接口 / Connector SMA内螺内孔 BW2.4GJWX156-13KK 蝙蝠无线 BAT WIRELESS 参数 / Parameters 典型值 / Typ.单位 / Unites 备注 / Notes 类型 / Antenna Type胶棒天线 / Rubber Antenna 频率 / Frequency Range2400-2500MHz 输入阻抗 / Input Impendence 50 Ω 驻波比 / V.S.W.R <2 增益 / Gain 4.13 dBi 极化方式 / Polarization Type垂直 / Vertical 功率容量 / Power Capacity 50W 雷电保护 / Lightning Protection - 工作电压 / DC Voltage -V 辐射体 / Radiator - 尺寸 / Dimensions 156 x ⌀13 mm 接口形式 / Connector Type SMA内螺内孔 电缆型号 / Cable Type - 电缆长度 / Cable Length - mm 安装方式 / Mount way 旋拧 颜色 / Color黑色 材料 / Meterial ABS 重量 / Weight - g 防护等级 / Waterproof Rating - ROHS标准 / ROHS Complaint 符合 工作温度 / Operating Temperature -45~ +85 °C 存储温度 / Storage Temperature -45~ +85 °C 2. . 产品规格 / Specification www.batwireless.cn July-21-2025-A01 电气特性 / Electrical Characteristics 机械特性 / Mechanical Characteristics 环境特性 / Environmental Characteristics 4 / 13 蝙蝠无线 BAT WIRELESS 3. . 实物图 / Dimensions www.batwireless.cn July-21-2025-A01 5 / 13 蝙蝠无线 BAT WIRELESS 图片仅供参考，以实物为准。 4. . 尺寸图 / Mechanical Drawing www.batwireless.cn July-21-2025-A01 6 / 13 蝙蝠无线 BAT WIRELESS Testing Capability / 测试能力 Description / 能力描述 Active measurement 有源测试 Capability /测试指标: TRP 、TIS 、EIRP 、EIS,. etc Mode /测试制式: 2G/3G/4G/5G 、Wi-Fi b/g/n/a/ac/ax 、BT 、NB-IOT 、 Cat-M(eMTC) 、GPS/BEIDOU/GLONASS 、ZigBee 、LoRa(Non- Signaling),.etc Pasive measurement 无源测试 Test category /测试类型: Gain 、Efficiency 、2D pattern 、3D pattern 、 Pattern roundness、Axial Ratio, ECC,Phase center,. etc Polarization /极化方式: Circular polarization, linear polarization, elliptical polarization DT-3500 Datasheet / 系统规格 Specification:Description Test Frequency /测试频域: 400MHz-8.5GHz System Size /系统尺寸: L*W*H=4*3.5*3.5m Number of Probes /探头数目:23 (Probe) + 1 (link) Interval Angle /采样夹脚: 15º Sampling Diameter /采样直径: 2200mm Carring Capacity /承载能力: ≦40kg 5. . 测试设备 / Test Equipment Keysight/E5071C 网络分析仪 R&S/CMW500 综测仪 R&S/SMBV100B 信号源 www.batwireless.cn July-21-2025-A01 7 / 13 蝙蝠无线 BAT WIRELESS RF Link diaram of multi probe spherical near-field testing system 多探头球面近场测试系统射频链路图 RF Link Overview RF Link Passive measurement www.batwireless.cn July-21-2025-A01 RF Link Overview 总射频链路图 RF Link of Passive measurement 无源测试链路图 RF Link Overview 总射频链路图 RF Link of Passive measurement 无源测试链路图 8 / 13 蝙蝠无线 BAT WIRELESS www.batwireless.cn 6.1 电压驻波比 / VSWR July-21-2025-A01 6.2 回波损耗 / Return Loss 9 / 13 蝙蝠无线 BAT WIRELESS 6. . 性能数据 / Performance Data 6. . 性能数据 / Performance Data www.batwireless.cn 6.3 增益 / Gain July-21-2025-A01 6.4 效率 / Efficiency 10 / 13 蝙蝠无线 BAT WIRELESS 频率 / Frequency (MHz)240024502500 最大增益 / Gain (dBi) 3.653.984.13 效率 / Efficiency (%)73.96 82.0483.18 6.5 天线增益与效率 0.00 10.00 20.00 30.00 40.00 50.00 60.00 70.00 80.00 90.00 100.00 2400.02410.02420.02430.02440.02450.02460.02470.02480.02490.02500.0 Efficiency (%) -2.31 -1.31 -0.31 0.69 1.69 2.69 3.69 4.69 2400.02410.02420.02430.02440.02450.02460.02470.02480.02490.02500.0 Efficiency (dBi)Gain (dBi) 7. . 辐射模式 / Radiation Patterns www.batwireless.cn July-21-2025-A01 7.1 2D 辐射模式图 / Radiation Patterns 11 / 13 蝙蝠无线 BAT WIRELESS www.batwireless.cn July-21-2025-A01 7.2 . 3D辐射模式图 / 3D Radiation Patterns 12 / 13 蝙蝠无线 BAT WIRELESS 版本： July-21-2025-A01 日期： 2025-7-21 备注： 首次更新 作者： Carly 文档记录 / Documentation www.batwireless.cn July-21-2025-A01 13 / 13 变更记录 / Change Log 蝙蝠无线 BAT WIRELESS Office Add：Room 1301, 13th Floor, No. 8 Langhua Road, Xinshi Community, Dalang Street, Longhua District, Shenzhen 蝙蝠无线 BAT WIRELESS 地址：深圳市龙华区大浪街道新石社区浪花路8号1301 深圳市蝙蝠无线技术有限公司 Shenzhen Bat Wireless Technology Co,.Ltd Tel：+86-0755-21031236 Email：[email protected]

Conducted Emission Test Setup: Radiated Emission Test Setup: RF test Setup: