2BC2U-ST30One-Touch Deploy Selfie Stick Tripod

大力神 手机摄影酷支架 蓝牙连接手机 首先将手机支架拉手向上拉出，然后垂直地平面大约 10cm高度落下，即可自动弹开自拍杆三脚架。 约10cm 合拢时一只手握住自拍杆中部位置，另一只手将拉杆 逐节推回手柄套筒内。 遥控器采用磁铁吸附，向外取出即可，装回时只需 对准槽位，即可自动吸附。 本产品采用专利滑轨式手机支架，预留前后倾，左右旋 铅汞镉 部件名称 PbHgCdCr(VI)PBBsPBDEs 六价铬多溴联苯多溴联苯醚 为避免造成设备损坏，请注意： 服务热线 : 0755-84827936 *本说明书中的图片及文字解释权归欧森隆（中国） 用户信息 姓名：________________________________________ 联系电话：____________________________________ 购买日期：____________________________________ 购买平台及店铺名：____________________________ 订单号：______________________________________ 产品信息 产品型号：____________________________________ 使用时注意用力适度，避免暴力拉扯或者用力过猛造成产 请勿将设备暴露于雨水或潮湿环境中； 请勿将任何明火火源（如点燃的蜡烛）放置在设备上或靠 近设备； 请勿将设备放置在热源附近，例如烤箱、散热器、火炉等 其它发热设备； 请勿将设备暴露于沸水环境中； 请勿将设备放置在装有液体的物品中，如花瓶等； 请勿将设备放置于高温灼热的环境中； 品的损坏； 自拍支架 包装配件 本表依据SJ/T11364的规定编制。 ：表示该有毒有害物质在该部件所有均质材料中的含量均 在GB/T26572标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的 含量超出GB/T26572标准规定的限量要求。 为保护人类环境和人类健康： 1.本产品报废后请将其与生活垃圾分开，消费者有责任将其 送至有资质的回收点； 2.回收中心将通过适当的方法回收再利用产品中的材料； 3.关于本产品回收处理的详细信息，请咨询当地政府、废品 请勿擅自拆开设备后盖，使用者不可自行维修内部零件， 以防触电或损坏设备。 处理中心或经销商。 本产品的环保使用期限为10年。（仅在用户手册所述要求 下使用本产品，上述“环保使用期限”才有效） 1.将手机固定在手机支架上，长按拍照键3秒至绿灯闪 烁开启蓝牙配对模式； 2.打开手机蓝牙设置，搜索并连接“SEAJIC MT2”， 成功后绿灯长亮； 3.按下自拍杆的拍照键进行拍照，再次长按拍照键3 秒，则关闭自拍支架电源，同时关闭蓝牙配对模式。 SEAJIC MT2 注意：自拍支架默认连接已配对成功的手机，如您需要 更换连接手机设备，请先在已连接的手机上取消 蓝牙配对，再连接配对新设备。 产品型号: ST30 整机尺寸: 332*48*39mm 产品重量: 420g 连接方式: 蓝牙 遥控距离: 10m 支持系统: Android/IOS 产品材料: ABS+PC/铝 电池容量: 50mAh Type-C输入: 5V/100mA 水淋湿或受潮、无法正常运转、设备跌落损坏等，请联系 官方客服咨询相关事宜。 重要安全信息 1.使用前请仔细阅读所有安全和操作说明，并妥善保管用户 手册，以备日后查阅； 2.请注意设备上和用户手册中所有注意事项； 3.请遵从所有操作和使用说明； 4.仅可使用生产厂商指定的附件/配件； 5.本设备须由官方维修人员进行维修操作； 6.如果本设备损坏，例如支架体损坏、液体渗入、设备遭雨 取出遥控器安装遥控器 产品介绍打开/合拢支架 横竖屏切换说明 转空间，不取手机也可以横竖屏自由切换。 遥控器充电 请使用USB数据线为支架遥控器充电。使用中遥控器电 量较低时，指示灯呈红色闪烁状态，充电中指示灯呈红 色常亮状态，充电完成时指示灯熄灭。 规格参数 产品有毒有害物质的名称和含量 注意SEAJIC产品售后服务 SEAJIC售后服务承诺：所有SEAJIC官方渠道及官方授权渠 道出售的商品，SEAJIC将严格根据《中华人民共和国消费 者权益保护法》及现行有效的法律法规，对于执行特殊三 包条约的地区，SEAJIC承诺遵守当地的相关规定提供售后 服务。为了保障您的权益，请您在购买SEAJIC产品后妥善 保管保修卡和有效购买凭证 SEAJIC产品保修卡 手机固定支架 将手机横向倾斜45度，放入手机支架上，轻轻用力往 上推，手机即可固定在支架上。 OSM PASS 地面/平面 About 10cm Drop vertically 地面/平面 手机夹 AB226 说明书 成品尺寸: 60x90mm 展开尺寸: 600x90mm 80克书写纸单黑印刷 （颠覆性专利 落地自动弹开） 用户手册 three-warranty services for all products which are sold through the official channel or authorized channel of SEAJIC in strict accordance with Law of the People's Republic of China on Protection of Consumer Rights and Interests. For regions where special three-warranty regulations are executed, SEAJIC hereby undertakes to abide by the local regulations. Please keep the warranty card and effective purchase voucher properly in order to safeguard your legal rights. OSM (China) owns the right of interpretation of pictures and texts in the Manual。 Connect Bluetooth to mobile phone 1. Fix the mobile phone onto the holder, press and hold the camera button for 3s until the green lamp flickers, to enter the Bluetooth pairing mode; 2. Enter Bluetooth settings of mobile phone, to search and connect “SEAJIC MT2”; the green indicator will be normally on after successful connection; 3. Press the camera button on the product to take photos; press and hold the camera button for 3s to power off the product and disable Bluetooth pairing mode. Handle of mobile phone holderPhone holder Rotation head Aluminum alloy pull rod Handle sleeve Camera/On/Off button Separate remote control Tripod Attention: The product will connect the successfully paired mobile phone by default. To connect a new mobile phone, you need to unpair the former mobile phone before pairing a new one。 SEAJIC MT2 Product Introduction Connection mode: Bluetooth Distance of remote control: 10m Supported system: Android/IOS Materials: ABS+PC/aluminum Battery capacity: 50mAh Model: ST30 Overall dimensions: 332*48*39mm Weight: 420g Type-C input: 5V/100mA This table was prepared according to SJ/T11364 : It means that the content of the toxic and hazardous substance in all the homogeneous materials of the component is below the limit requirements specified in GB/T 26572. Ｘ: It means that the content of the toxic and harmful substance in at least one homogeneous material of the component exceeds the limit requirements specified by GB/T 26572. To protect the environment and human health: 1. Once scrapped, the product should be separated from the household wastes; users have responsibilities for sending the scrapped products to the designated recycling center; 2. The recycling center should recycle the product's useful materials properly; 3. For details of scrapping the product, please consult the local government, waste disposal center or dealer; The product's environmentally friendly service life, which is 10 years, is determined by the enterprise according to its design characteristics. The product's environmentally friendly service life is effective only when the product is used under the normal conditions mentioned in the Manual。 2. Please pay attention to all precautions on the product and in the Manual; 3. Please follow all operation and use instructions; 4. Use the accessories/attachments designated by the manufacturer only; 5. The product must be maintained by professionals; 6. For any damage of the product, such as holder damage, liquid penetration, affection by rainwater or moisture, functioning failure or damage due to falling, please contact the official after-sales service specialist to receive the designated maintenance service。 Important safety information 1. Please read all safety and operation instructions carefully before using the product. Keep the manual properly for further use; Specification & parameters Parts Pb Cd Cr(VI) Chromium PBBs piphenyls PBDEs diphenyl ethers Selfie stick Packing accessories Name and content of toxic and hazardous substances or elements in the product Name and content of hazardous substances in the product After-sales services of SEAJIC After-sales service commitment of SEAJIC: We provide Warranty Card of SEAJIC User Information Name: _________________________________________________ Contact phone:_________________________________________ Date of purchase:_____________________________________…

Text truncated - open the document above for the full version.

Shenzhen LC Co., Ltd Rooms 602, Building 5, Fenghe Industrial Park, No. 1301-50 Guanguang Road, Xinlan Community, Guanlan Street, Longhua District, Shenzhen China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-8-2 U.S. Agent Designation Shenzhen LC Co., Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BC2U-ST30): Name and company of U.S. agent: ACT Lab LLC Physical U.S. address of agent: 3280 East 59th Street Long Beach, CA 90805 United States FRN of U.S. agent: 0033465568 Email address of U.S. agent: [email protected] ACT Lab LLC acknowledges their obligation to accept service of process on behalf of Shenzhen LC Co., Ltd. Shenzhen LC Co., Ltd with the FRN [0034288399] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Wei Xi N/A Shenzhen LC Co., Ltd Signature Scott Huber Senior Technical Director ACT Lab LLC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Photo 5 Appearance of EUT Photo 6 Appearance of EUT FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Photo 7 Appearance of EUT Photo 8 Appearance of EUT FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Photo 9 Appearance of EUT

FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Appendix IID Label Appendix II ID Label Location One-Touch Deploy Selfie Stick Tripod FCC ID: 2BC2U-ST30 Model: ST30

FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 10 Internal of EUT Photo 11 Appearance of PCB & Battery FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Photo 12 Appearance of PCB & Battery Photo 13 Internal of Battery FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Photo 14 Appearance of PCB Photo 15 Appearance of PCB FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Photo 16 Appearance of PCB Antenna

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202407-0225-5 Page: 1 of 2 TB-RF-074-1.0 1 A/F., Building.6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao’an, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 RF Exposure Evaluation FCC ID: 2BC2U-ST30 1. Client Information Applicant : Shenzhen LC Co., Ltd Address : Rooms 602, Building 5, Fenghe Industrial Park, No. 1301-50 Guanguang Road, Xinlan Community, Guanlan Street, Longhua District, Shenzhen, China. Manufacturer : Shenzhen Leqi Innovation Co., Ltd. Address : Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50 Guanguang Road, Longhua District, Shenzhen, Guangdong, China. 2. General Description of EUT EUT Name : One-Touch Deploy Selfie Stick Tripod Model(s) No. : ST30 Model Difference : ---- Product Description : Operation Frequency: Bluetooth LE 4.2: 2402MHz~2480MHz Number of Channel: 40 channels Antenna Gain: 2.3dBi PCB Antenna Modulation Type: GFSK Power Supply : USB Input: DC 5V/0.1A DC 3.7V 50mAh 0.185Wh Rechargeable Li-ion battery Software Version : V1.1 Hardware Version : V1.0 Remark: (1) The antenna gain provided by the applicant, the verified for the RF conduction test provided by TOBY test lab. (2) For a more detailed features description, please refer to the manufacturer’s specifications or the User’s Manual. (3) The above antenna information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications, the laboratory shall not be held responsible. Note: More test information about the EUT please refer the RF Test Report. Report No.: TBR-C-202407-0225-5 Page: 2 of 2 TB-RF-074-1.0 SAR Test Exclusion Calculations 1. FCC: According to KDB 447498 D01 Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies v06. (1) Clause 4.3: General SAR test reduction and exclusion guidance Sub clause 4.31: Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6GHz at test separation distance≤5 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤3.0 for 1-g SAR [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤7.5.0 for 10-g SAR 2. Calculation: Test separation: 5mm Bluetooth LE Mode (1M) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dBm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.402 2.062 2±1 3 1.995 0.618 3.0 2.440 1.781 1±1 2 1.585 0.495 3.0 2.480 1.579 1±1 2 1.585 0.499 3.0 Bluetooth LE Mode (2M) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dBm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.402 2.099 2±1 3 1.995 0.618 3.0 2.440 1.833 1±1 2 1.585 0.495 3.0 2.480 1.621 1±1 2 1.585 0.499 3.0 The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. -----END OF THE REPORT-----

1. Antenna Description: Antenna plate Monopole Antenna Antenna peak gain 2.3 dBi Frequency range 2.402MHz~2.480MHz Connect type Direct Connect Mode Oth-AB226 Band 2. Picture of antenna 3. Antenna Radiation Pattern Radiation pattern @2.402GHz Radiation pattern @2.441GHz Radiation pattern @2.480GHz

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 1 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 RF Test Data for Bluetooth LE (Conducted Measurements) General Description of EUT Product Name: One-Touch Deploy Selfie Stick Tripod Test Model: ST30 Sample ID: HC-C-202407-0225-01-01-2# Environmental Conditions Temperature: 23.8°C Relative Humidity: 48% Test Voltage: DC 3.7V Test Engineer: Jolin Lee Note: For a more detailed features description, please refer to the report TBR-C-202407-0225-11 The report only show the worst case data. Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 2 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Contents 1. Duty Cycle ........................................................................................................................................................................................... 3 2. Maximum Conducted Output Power ................................................................................................................................................. 7 3. -6dB Bandwidth ................................................................................................................................................................................ 11 4. Occupied Channel Bandwidth ......................................................................................................................................................... 15 5. Maximum Power Spectral Density Level ......................................................................................................................................... 19 6. Band Edge ........................................................................................................................................................................................ 23 7. Conducted RF Spurious Emission .................................................................................................................................................. 28 8. Restrict Band .................................................................................................................................................................................... 35 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 3 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 1. Duty Cycle Condition Mode Frequency (MHz) Antenna Duty Cycle (%) Correction Factor (dB) 1/T (kHz) NVNT BLE 1Mbps 2402 Ant1 100 0 0 NVNT BLE 1Mbps 2440 Ant1 100 0 0 NVNT BLE 1Mbps 2480 Ant1 100 0 0 NVNT BLE 2Mbps 2402 Ant1 100 0 0 NVNT BLE 2Mbps 2440 Ant1 100 0 0 NVNT BLE 2Mbps 2480 Ant1 100 0 0 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 4 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Test Graphs Duty Cycle NVNT BLE 1Mbps 2402MHz Ant1 Duty Cycle NVNT BLE 1Mbps 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 5 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Duty Cycle NVNT BLE 1Mbps 2480MHz Ant1 Duty Cycle NVNT BLE 2Mbps 2402MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 6 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Duty Cycle NVNT BLE 2Mbps 2440MHz Ant1 Duty Cycle NVNT BLE 2Mbps 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 7 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 2. Maximum Conducted Output Power Condition Mode Frequency (MHz) Antenna Conducted Power (dBm) Limit (dBm) Verdict NVNT BLE 1Mbps 2402 Ant1 2.062 30 Pass NVNT BLE 1Mbps 2440 Ant1 1.781 30 Pass NVNT BLE 1Mbps 2480 Ant1 1.579 30 Pass NVNT BLE 2Mbps 2402 Ant1 2.099 30 Pass NVNT BLE 2Mbps 2440 Ant1 1.833 30 Pass NVNT BLE 2Mbps 2480 Ant1 1.621 30 Pass Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 8 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Test Graphs Power NVNT BLE 1Mbps 2402MHz Ant1 Power NVNT BLE 1Mbps 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 9 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Power NVNT BLE 1Mbps 2480MHz Ant1 Power NVNT BLE 2Mbps 2402MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 10 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Power NVNT BLE 2Mbps 2440MHz Ant1 Power NVNT BLE 2Mbps 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202407-0225-11 Page: 11 of 39 FCC ID: 2BC2U-ST30 TB-RF-074-1.0 3. -6dB Bandwidth Condition Mode Frequency (MHz) Antenna -6 dB Bandwidth (MHz) Limit -6 dB Bandwidth (MHz) Verdict NVNT BLE 1Mbps 2402 Ant1 …

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202407-0225-11 Page: 1 of 37 TB-RF-074-1.0 1/F., Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 RF Test Report FCC ID: 2BC2U-ST30 Report No. : TBR-C-202407-0225-11 Applicant : Shenzhen LC Co., Ltd Equipment Under Test (EUT) EUT Name : One-Touch Deploy Selfie Stick Tripod Model No. : ST30 Series Model No. : ---- Brand Name : SmallRig Sample ID : HC-C-202407-0225-01-01-1#&HC-C-202407-0225-01-01-2# Receipt Date : 2024-07-23 Test Date : 2024-07-23 to 2024-08-02 Issue Date : 2024-08-02 Standards : FCC Part 15 Subpart C 15.247 Test Method : ANSI C63.10:2013 KDB 558074 D01 15.247 Meas Guidance v05r02 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above. Tested By : Jolin Lee Reviewed By : Wade. Lv Approved By : Ivan Su This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TBR-C-202407-0225-11 Page: 2 of 37 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................. 2 1. GENERAL INFORMATION ABOUT EUT.............................................................................. 5 1.1 Client Information ................................................................................................................. 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 7 1.5 Description of Test Mode .................................................................................................... 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility ........................................................................................................................... 9 2. TEST SUMMARY ..................................................................................................................... 10 3. TEST SOFTWARE ................................................................................................................... 10 4. TEST EQUIPMENT AND TEST SITE ................................................................................... 11 5. CONDUCTED EMISSION ....................................................................................................... 13 5.1 Test Standard and Limit .................................................................................................... 13 5.2 Test Setup ........................................................................................................................... 13 5.3 Test Procedure ................................................................................................................... 13 5.4 Deviation From Test Standard ......................................................................................... 14 5.5 EUT Operating Mode ........................................................................................................ 14 5.6 Test Data ............................................................................................................................. 14 6. RADIATED AND CONDUCTED UNWANTED EMISSIONS ............................................ 15 6.1 Test Standard and Limit .................................................................................................... 15 6.2 Test Setup ........................................................................................................................... 17 6.3 Test Procedure ................................................................................................................... 18 6.4 Deviation From Test Standard ......................................................................................... 19 6.5 EUT Operating Mode ........................................................................................................ 19 6.6 Test Data ............................................................................................................................. 19 7. RESTRICTED BANDS REQUIREMENT ............................................................................. 20 7.1 Test Standard and Limit .................................................................................................... 20 7.2 Test Setup ........................................................................................................................... 20 7.3 Test Procedure ................................................................................................................... 21 7.4 Deviation From Test Standard ......................................................................................... 22 Report No.: TBR-C-202407-0225-11 Page: 3 of 37 TB-RF-074-1.0 7.5 EUT Operating Mode ........................................................................................................ 22 7.6 Test Data ............................................................................................................................. 22 8. BANDWIDTH TEST ................................................................................................................. 23 8.1 Test Standard and Limit ............................................…

Text truncated - open the document above for the full version.

FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Appendix V EUT Test Photographs Photo of Setup for Radiated Emission (Below 1 GHz) Photo of Setup for Radiated Emission (Above 1 GHz) FCC ID: 2BC2U-ST30 TB-RF-074-1.0 Photo of Setup for Radiated Emission (Above 1 GHz) Photo of Setup for Conducted Emission -----END OF THE REPORT-----