2BE3V-Q9Tablet PC

Q9 Tablet PC 17 8 2 10 9 3 4 11 5 6 MTK8766 Quad core 3+5GB 2.4GWiFi IPS 1024*600 32GB 14 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure statement The device has been evaluatec to meel general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Shenzhen Peicheng Technology Co.,Ltd Covered Equipment Certification Attestation Letter 12/29/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BE3V-Q9 Shenzhen Peicheng Technology Co.,Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Shenzhen Peicheng Technology Co.,Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Shenzhen Peicheng Technology Co.,Ltd (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). <Signature>: Name: Shaobin Chen Title: Manager Company: Shenzhen Peicheng Technology Co.,Ltd Date: 12/29/2025

Shenzhen Peicheng Technology Co.,Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 12/29/2025 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2BE3V-Q9 FRN of applicant: 0034963744 Per section 2.911(d)(7) of the FCC rules, [Shenzhen Peicheng Technology Co.,Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Herland International Trading Inc FCC Registration Number (FRN): 0036324101 Physical U.S. Company Address: 1370 Valley Vista Dr Ste 200 Diamond Bar, CA 91765 Contact Person: Jianfeng Gao Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Shaobin Chen Title: Manager Company Name: Shenzhen Peicheng Technology Co.,Ltd Date: 12/29/2025 Agent Signed (if different from Applicant): Signed: Printed name: Jianfeng Gao Title: Manager Company Name: Herland International Trading Inc Date: 12/29/2025

Shenzhen Peicheng Technology Co.,Ltd 2025-12-25 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen DL Testing Technology Co., Ltd.（101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China）to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shenzhen Peicheng Technology Co.,Ltd（5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China） <Signature>: Name: Shaobin Chen Title: Manager Company: Shenzhen Peicheng Technology Co.,Ltd

Shenzhen Peicheng Technology Co.,Ltd 2025-12-25 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature>: Name: Shaobin Chen Title: Manager Company: Shenzhen Peicheng Technology Co.,Ltd

Shenzhen Peicheng Technology Co.,Ltd 2025-12-25 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BE3V-Q9 Product Name: Tablet PC Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>: Name: Shaobin Chen Title: Manager Company: Shenzhen Peicheng Technology Co.,Ltd

Shenzhen Peicheng Technology Co.,Ltd Product function Declaration Applicant: Shenzhen Peicheng Technology Co.,Ltd Address: 5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China Manufacturer: Shenzhen Peicheng Technology Co.,Ltd Address: 5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China Product Name: Tablet PC Trade Mark: N/A Model Number: Q9 We (Shenzhen Peicheng Technology Co.,Ltd) here by state that The product has (WIFI 5G) function at the beginning of design. However, due to the iteration of the product, this function is no longer required at present, so through the (Software mask) method, the function is forced off, and the product (FCC ID: 2BE3V-Q9) no longer has the (WIFI5G) function. Signature: <Signature>: Name: Shaobin Chen Title: Manager Company: Shenzhen Peicheng Technology Co.,Ltd

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(External Photos) Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

Size: 16*12mm Model.: Q9 FCC ID: 2BE3V-Q9 Label location

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(Internal Photos) ANT Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

FCC ID: 2BE3V-Q9 RF Exposure Evaluation According to KDB 447498 D01 V06 and part 2.1093，Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f (GHz) ] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f (GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Here, BT Peak Output Power (dBm) Max tune-up (mW) Frequency (MHz) Min. distance(mm) Calc. thresholds limit 4.28 2.7 2402 5 0.8 3.0 BLE Peak Output Power (dBm) Max tune-up (mW) Frequency (MHz) Min. distance(mm) Calc. thresholds limit 1.53 1.4 2402 5 0.4 3.0 WiFi Peak Output Power (dBm) Max tune-up (mW) Frequency (MHz) Min. distance(mm) Calc. thresholds limit 7.96 6.3 2452 5 2.0 3.0 For Simultaneous transmitting, 1): The sum of the ratios of the spatially averaged results to the applicable frequency dependent MPE limits =0.8/3 + 2.0/3 = 0.93< 1 Since the sum of the MPE ratios for all simultaneously transmitting antennas incorporated in the device is ≤ 1.0, the EUT is considered to satisfy MPE compliance for simultaneous transmission operations. So a SAR test is not required

Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109038R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 33 FCC Part 15C Test Report FCC ID: 2BE3V-Q9 Applicant: Shenzhen Peicheng Technology Co.,Ltd Address: 5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China Manufacturer: Shenzhen Peicheng Technology Co.,Ltd Address: 5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China Product Name: Tablet PC Trade Mark: N/A Model Number: Q9 Date of Receipt: Jan. 09, 2026 Test Date: Jan. 09, 2026 - Jan. 22, 2026 Date of Report: Jan. 22, 2026 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Report Number: DLE-260109038R Prepared (Test Engineer): Alisa Song Reviewer (Supervisor): Jack Bu Approved (Manager): Jade Yang This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109038R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 33 Table of Contents Page 1. . SUMMARY OF TEST RESULTS 4 1.1. MEASUREMENT UNCERTAINTY 4 2. . GENERAL INFORMATION 5 2.1. GENERAL DESCRIPTION OF EUT 5 2.2. DESCRIPTION OF TEST MODES 6 2.3. BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 6 2.4. DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 7 2.5. TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 7 2.6. EQUIPMENTS LIST FOR ALL TEST ITEMS 8 3. . EMC EMISSION TEST 9 3.1. CONDUCTED EMISSION MEASUREMENT 9 3.1.1. POWER LINE CONDUCTED EMISSION LIMITS 9 3.1.2. TEST PROCEDURE 9 3.1.3. DEVIATION FROM TEST STANDARD 9 3.1.4. TEST SETUP 10 3.1.5. EUT OPERATING CONDITIONS 10 3.1.6. TEST RESULTS 11 3.2. RADIATED EMISSION MEASUREMENT 13 3.2.1. RADIATED EMISSION LIMITS 13 3.2.2. TEST PROCEDURE 14 3.2.3. DEVIATION FROM TEST STANDARD 14 3.2.4. TEST SETUP 14 3.2.5. EUT OPERATING CONDITIONS 15 3.2.6. TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 16 3.2.7. TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 17 3.2.8. TEST RESULTS (1GHZ~25GHZ) 19 3.3 RADIATED BAND EMISSION MEASUREMENT 20 3.3.1 TEST REQUIREMENT: 20 3.3.2 TEST PROCEDURE 20 3.3.3 DEVIATION FROM TEST STANDARD 20 3.3.4 TEST SETUP 21 3.3.5 EUT OPERATING CONDITIONS 21 3.4 CONDUCTED BAND EDGE EMISSION&CONDUCTED SPURIOUS EMISSIONS MEASUREMENT 23 3.4.1 APPLICABLE STANDARD 23 3.4.2 TEST PROCEDURE 23 3.4.3 DEVIATION FROM STANDARD 23 3.4.4 TEST SETUP 23 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109038R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 33 Table of Contents Page 3.4.5 EUT OPERATION CONDITIONS 23 3.4.6 TEST RESULTS 23 4. . PEAK OUTPUT POWER 26 4.1. APPLIED PROCEDURES / LIMIT 26 4.1.1. TEST PROCEDURE 26 4.1.2. DEVIATION FROM STANDARD 26 4.1.3. TEST SETUP 26 4.1.4. EUT OPERATION CONDITIONS 26 4.1.5. TEST RESULTS 27 5. . POWER SPECTRAL DENSITY TEST 29 5.1. APPLIED PROCEDURES / LIMIT 29 5.1.1. TEST PROCEDURE 29 5.1.2. DEVIATION FROM STANDARD 29 5.1.3. TEST SETUP 29 5.1.4. EUT OPERATION CONDITIONS 29 5.1.5. TEST RESULTS 29 6. . 6DB BANDWIDTH TEST 31 6.1. APPLIED PROCEDURES / LIMIT 31 6.1.1. TEST PROCEDURE 31 6.1.2. DEVIATION FROM STANDARD 31 6.1.3. TEST SETUP 31 6.1.4. EUT OPERATION CONDITIONS 31 6.1.5. TEST RESULTS 31 7. . ANTENNA REQUIREMENT 33 7.1. STANDARD REQUIREMENT 33 7.2. EUT ANTENNA 33 8. . TEST SEUUP PHOTO 33 9. . EUT PHOTO 33 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109038R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 33 1.. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247(c) Radiated Spurious Emission PASS 15.205 Band Edge Emission PASS 15.247(b) Peak Output Power PASS 15.247(a)(2) 6dB Bandwidth PASS 15.247(e) Power Spectral Density PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Test lab: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China FCC Test Firm Registration Number: 854456 Designation Number: CN1307 IC Registered No.: 27485 CAB ID.: CN0118 1.1. MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±2.56dB 2 RF power,conducted ±0.42dB 3 Spurious emissions,conducted ±2.76dB 4 All emissions,radiated(<1G) ±3.65dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% 8 6dB Bandwidth ±0.2MHz 9 Power Spectral Density ±0.3dBm Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109038R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 33 2.. GENERAL INFORMATION 2.1. GENERAL DESCRIPTION OF EUT Product Name: Tablet PC Trade Mark: N/A Model Number: Q9 Test Model: Q9 Model Difference: N/A Operation Frequency: 2402~2480MHz Channel numbers: 40 Channels Channel separation: 1MHz Data Rate: 1Mbps Modulation technology: GFSK Antenna Type: Internal Antenna Antenna gain: 1.51 dBi Power supply: DC 5V DC 3.8V from battery Note: 1.For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2.The EUT’s all information pro…

Text truncated - open the document above for the full version.

深圳市千目通讯科技有限公司 ShenzhenQianmuCommunicationTechnologyCo.,Ltd. 联系人：王志强联系方式：13760153961电话：0755-21633653传真：0755-21633541 深圳市宝安区航城街道三围社区航空路华丰智谷-航城高科技产业园A座4层425、443号 天线承认书 适用型号 Q8PRO 客户 深圳市佩城科技有限公司 规格描述 产品内容规格客户物料编码 规 格 描 述 WiFi天线 FPC/黑色/字符QM-Q8PRO-GWB-V1.0 +线材1.13*55mm+导电布 Q9000G001 更改履历 序号日期版本更改内容简述 1 2026-01-30V1.0新项目 2 3 供应商样品确认 研发结构审核判定 PASS FAIL 客户样品确认 电子结构项目采购品质审核 拒收原因或其它注意事项： — 2 — 1、匹配电路-WIFI天线 原始匹配电路未做更改 2、有源测试数据 3、天线增益效率 — 3 — 4、天线方向图 5、天线实测 — 4 — 6、环境处理与天线摆放位置 — 5 — 7、工程图

Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 75 ANNEX 1 TEST DATA FCC ID: 2BE3V-Q9 Applicant: Shenzhen Peicheng Technology Co.,Ltd Address: 5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China Manufacturer: Shenzhen Peicheng Technology Co.,Ltd Address: 5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China Product Name: Tablet PC Trade Mark: N/A Model Number: Q9 Date of Receipt: Jan. 09, 2026 Test Date: Jan. 09, 2026 - Jan. 22, 2026 Date of Report: Jan. 22, 2026 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 75 1. Maximum Conducted Output Power Mode TX Type Frequency (MHz) Maximum Average Output Power (dBm) Total Output Power(dBm) Limit Verdict ANT1 Duty Cycle (dB) 802.11b SISO 2412 7.25 0.16 7.41 <=30 Pass 2437 6.55 0.17 6.72 <=30 Pass 2462 5.88 0.17 6.05 <=30 Pass 802.11g SISO 2412 7.28 0.13 7.41 <=30 Pass 2437 7.63 0.14 7.77 <=30 Pass 2462 7.14 0.13 7.27 <=30 Pass 802.11n (HT20) SISO 2412 7.23 0.14 7.37 <=30 Pass 2437 6.90 0.14 7.04 <=30 Pass 2462 6.09 0.14 6.23 <=30 Pass 802.11n (HT40) SISO 2422 7.55 0.28 7.83 <=30 Pass 2437 7.47 0.28 7.75 <=30 Pass 2452 7.15 0.28 7.43 <=30 Pass 802.11ax (HEW20) SISO 2412 6.32 0.14 6.46 <=30 Pass 2437 7.17 0.14 7.31 <=30 Pass 2462 7.08 0.14 7.22 <=30 Pass 802.11ax (HEW40) SISO 2422 7.12 0.28 7.40 <=30 Pass 2437 7.53 0.28 7.81 <=30 Pass 2452 7.68 0.28 7.96 <=30 Pass Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 75 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 75 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 75 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 6 of 75 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 7 of 75 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_LCH_2422MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 8 of 75 802.11n(HT40)_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_HCH_2452MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 9 of 75 802.11ax(HEW20)_LCH_2412MHz_SU_ / _Ant1 (SISO)_NTNV 802.11ax(HEW20)_MCH_2437MHz_SU_ / _Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 10 of 75 802.11ax(HEW20)_HCH_2462MHz_SU_ / _Ant1 (SISO)_NTNV 802.11ax(HEW40)_LCH_2422MHz_SU_ / _Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 11 of 75 802.11ax(HEW40)_MCH_2437MHz_SU_ / _Ant1 (SISO)_NTNV 802.11ax(HEW40)_HCH_2452MHz_SU_ / _Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 12 of 75 2. -6dB Bandwidth Mode TX Type Frequency (MHz) 6dB Bandwidth (MHz) Verdict Result Limit 802.11b SISO 2412 9.469 >=0.5 Pass 2437 9.658 >=0.5 Pass 2462 9.760 >=0.5 Pass 802.11g SISO 2412 16.449 >=0.5 Pass 2437 16.469 >=0.5 Pass 2462 16.406 >=0.5 Pass 802.11n (HT20) SISO 2412 17.507 >=0.5 Pass 2437 17.752 >=0.5 Pass 2462 17.585 >=0.5 Pass 802.11n (HT40) SISO 2422 35.542 >=0.5 Pass 2437 35.007 >=0.5 Pass 2452 34.757 >=0.5 Pass 802.11ax (HEW20) SISO 2412 17.607 >=0.5 Pass 2437 16.624 >=0.5 Pass 2462 17.491 >=0.5 Pass 802.11ax (HEW40) SISO 2422 35.529 >=0.5 Pass 2437 30.843 >=0.5 Pass 2452 36.181 >=0.5 Pass Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 13 of 75 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 14 of 75 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 15 of 75 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 16 of 75 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 17 of 75 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_LCH_2422MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 18 of 75 802.11n(HT40)_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_HCH_2452MHz_Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 19 of 75 802.11ax(HEW20)_LCH_2412MHz_SU_ / _Ant1 (SISO)_NTNV 802.11ax(HEW20)_MCH_2437MHz_SU_ / _Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 20 of 75 802.11ax(HEW20)_HCH_2462MHz_SU_ / _Ant1 (SISO)_NTNV 802.11ax(HEW40)_LCH_2422MHz_SU_ / _Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 21 of 75 802.11ax(HEW40)_MCH_2437MHz_SU_ / _Ant1 (SISO)_NTNV 802.11ax(HEW40)_HCH_2452MHz_SU_ / _Ant1 (SISO)_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 22 of 75 3. Occupied Channel Bandwidth Mode TX Type Frequency (MHz) 99% Occupied Bandwidth (MHz) Verdict Result Limit 802.11b SISO 2412 13.488 / Pas…

Text truncated - open the document above for the full version.

Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109040R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 39 FCC Part 15C Test Report FCC ID: 2BE3V-Q9 Applicant: Shenzhen Peicheng Technology Co.,Ltd Address: 5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China Manufacturer: Shenzhen Peicheng Technology Co.,Ltd Address: 5th Floor, Building 64, Baotian Industrial Zone, Chentian Community, Xixiang Street, Baoan District, Shenzhen City, China Product Name: Tablet PC Trade Mark: N/A Model Number: Q9 Date of Receipt: Jan. 09, 2026 Test Date: Jan. 09, 2026 - Jan. 22, 2026 Date of Report: Jan. 22, 2026 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Report Number: DLE-260109040R Prepared (Test Engineer): Alisa Song Reviewer (Supervisor): Jack Bu Approved (Manager): Jade Yang This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109040R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 39 Table of Contents Page 1. . SUMMARY OF TEST RESULTS 4 1.1. MEASUREMENT UNCERTAINTY 4 2. . GENERAL INFORMATION 5 2.1. GENERAL DESCRIPTION OF EUT 5 2.2. DESCRIPTION OF TEST MODES 6 2.3. BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 7 2.4. DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 7 2.5. TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 7 2.6. EQUIPMENTS LIST FOR ALL TEST ITEMS 8 3. . EMC EMISSION TEST 9 3.1. CONDUCTED EMISSION MEASUREMENT 9 3.1.1. POWER LINE CONDUCTED EMISSION LIMITS 9 3.1.2. TEST PROCEDURE 9 3.1.3. DEVIATION FROM TEST STANDARD 9 3.1.4. TEST SETUP 10 3.1.5. EUT OPERATING CONDITIONS 10 3.1.6. TEST RESULTS 11 3.2. RADIATED EMISSION MEASUREMENT 13 3.2.1. RADIATED EMISSION LIMITS 13 3.2.2. TEST PROCEDURE 14 3.2.3. DEVIATION FROM TEST STANDARD 14 3.2.4. TEST SETUP 14 3.2.5. EUT OPERATING CONDITIONS 15 3.2.6. TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 16 3.2.7. TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 17 3.2.8. TEST RESULTS (1GHZ~25GHZ) 19 3.3 RADIATED BAND EMISSION MEASUREMENT 25 3.3.1 TEST REQUIREMENT: 25 3.3.2 TEST PROCEDURE 25 3.3.3 DEVIATION FROM TEST STANDARD 25 3.3.4 TEST SETUP 26 3.3.5 EUT OPERATING CONDITIONS 26 3.4 CONDUCTED BAND EDGE EMISSION&CONDUCTED SPURIOUS EMISSIONS MEASUREMENT 33 3.4.1 APPLICABLE STANDARD 33 3.4.2 TEST PROCEDURE 33 3.4.3 DEVIATION FROM STANDARD 33 3.4.4 TEST SETUP 33 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109040R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 39 Table of Contents Page 3.4.5 EUT OPERATION CONDITIONS 33 3.4.6 TEST RESULTS 33 4. . AVERAGE OUTPUT POWER 34 4.1. APPLIED PROCEDURES / LIMIT 34 4.1.1. TEST PROCEDURE 34 4.1.2. DEVIATION FROM STANDARD 34 4.1.3. TEST SETUP 34 4.1.4. EUT OPERATION CONDITIONS 34 4.1.5. TEST RESULTS 35 5. . POWER SPECTRAL DENSITY TEST 36 5.1. APPLIED PROCEDURES / LIMIT 36 5.1.1. TEST PROCEDURE 36 5.1.2. DEVIATION FROM STANDARD 36 5.1.3. TEST SETUP 36 5.1.4. EUT OPERATION CONDITIONS 36 5.1.5. TEST RESULTS 36 6. . 6DB BANDWIDTH TEST 37 6.1. APPLIED PROCEDURES / LIMIT 37 6.1.1. TEST PROCEDURE 37 6.1.2. DEVIATION FROM STANDARD 37 6.1.3. TEST SETUP 37 6.1.4. EUT OPERATION CONDITIONS 37 6.1.5. TEST RESULTS 37 7. . DUTY CYCLE TEST SIGNAL 38 7.1. APPLIED PROCEDURES / LIMIT 38 7.1.1. TEST PROCEDURE 38 7.1.2. DEVIATION FROM STANDARD 38 7.1.3. TEST SETUP 38 7.1.4. EUT OPERATION CONDITIONS 38 7.1.5. TEST RESULTS 38 8. . ANTENNA REQUIREMENT 39 8.1. STANDARD REQUIREMENT 39 8.2. EUT ANTENNA 39 9. . TEST SEUUP PHOTO 39 10. . EUT PHOTO 39 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260109040R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 39 1.. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.205, 15.209, 15.247(d) Radiated Spurious Emission PASS 15.205, 15.209 Conducted Spurious Emissions PASS 15.247(d) Band Edge Emission PASS 15.247(b) Average Output Power PASS 15.247(a)(2) 6dB Bandwidth PASS 15.247(e) Power Spectral Density PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Test lab: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the lssuing DL Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the DL Testing, responsible for this Test Report. FCC Test Firm Registration Number: 854456 Designation Number: CN1307 IC Registered No.: 27485 CAB ID.: CN0118 1.1. MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±2.56dB 2 RF power,conducted ±0.42dB 3 Spurious emissions,conducted ±2.76dB 4 All emissions,radiated(<1G) ±3.65dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% 8 6dB Bandwidth ±0.2MHz 9 Power Spectral Density ±0.42dB 10 Duty Cycle ±0.39dB Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-2…

Text truncated - open the document above for the full version.

Shenzhen DL Testing Technology Co., Ltd. EUT TEST PHOTO Radiated Measurement Photos Shenzhen DL Testing Technology Co., Ltd. Conducted Measurement Photos ※※※※※ END OF REPORT ※※※※※