2BEMH-MME1RMINI PC

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨⑩⑪ 1. HDMI Port 2. DC in Port 3. USB3.0 Port 4. HDMI Port 5. RJ-45 LAN Port 6. Audio Jack Port 7. Reset Hole 8. Power Button 9. USB3.0 Port 10. Full-function Type-C 11. Micro SD Card Port CAUTION Getting StartedEnter the Bios Setup FCC Conformity StatementWarranty Information Know Your Mini PCKnow Your Mini PC Package Contents NIMO Support MINI PC USER MANUAL Mini ComputerUser Manual AdapterVESA Your Mini PC is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important for you to read the following safety instructions. The MME1B and MME1R are covered for two years from the initial retail purchase date, as confirmed by the provided proof of purchase from the first retailer Nimo or a Nimo-authorized service center will repair. Repairs or replacements will be conducted in a commercially reasonable time, at the discretion of Nimo. If Nimo replaces the product, the replacement will be subject to the terms outlined in this warranty for the remaining duration of the original product's warranty period. The replacement product may be refurbished. The Warranty becomes invalid if the product has been disassembled, modified or repaired without Nimo’s authorization. Additionally, damage resulting from neglect, whether intentional or accidental, is not covered under warranty. Examples not covered by warranty include but are not limited to use outside operating specifications, a cracked or broken screen, damaged housing or cover, missing or damaged buttons, impaired ports or connectors, damage from power surge or incorrect power supply usage and water damage ( as Indicated by inspection of the internal liquid contact indicator). For warranty support or repair, please contact Customer Care: Phone Number:(302) 501-7208 Email: [email protected] Website: www.nimopc.com RTC Battery Warning CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. 1.Locate the VESA mount screw holes on the back of the Mini PC. They are located near the middle of the device. 2.Align the VESA mount bracket with the screw holes on the back of the Mini PC as the image instructions. Make sure the mount is level and centered. 3.Insert the screws (M3) through the holes on the mount and into the screw holes on the Mini PC. Use a screwdriver to tighten the screws but be careful not to over- tighten them. 4.Double-check that the Mini PC is securely attached to the VESA mount. 5.Attach the VESA mount to the back of your monitor. Align the VESA mount bracket with the screw holes on the back of your monitor. 6.Insert the screws (M4) through the holes on the mount and into the screw holes on the back of your monitor. Use a screwdriver to tighten the screws but be careful not to over-tighten them 7.Double-check that everything is securely in place and enjoy your newly mounted Mini PC and display. Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or heat sources. Set up the system on a stable surface. Openings on the chassis are for ventilation. Do not block or cover these openings. Make sure to leave plenty of space around the system for ventilation. Never insert objects of any kind into the ventilation openings. Use this product in environments with ambient temperatures between 0 and 35. If you use an extension cord, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. An error message appears on the screen during the system boot-up and requests you to run the BIOS Setup. You have installed a new system component that requires further BIOS settings or updates. Do not walk on the power cord or allow anything to rest on it. Do not spill water or any other liquids on your system. When the system is turned off, a small amount of electrical current still flows. or A small amount of electrical current continues to flow when the system is turned off. Always unplug the power cord from the power outlets before cleaning the system. If you encounter the following technical problems with the product, unplug the power cord and contact a qualified service technician or your retailer. The power cord or plug is damaged. Liquid has been spilled into the system. The system does not function properly even if you follow the operating instructions. The system was dropped or the chassis was damaged. The system performance changes. FCC Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference (2)This device must accept any interference received, including interference that may cause undesired operation. Care during use Setting up your system 1.Connect the DC power connector to your Mini PC’s power (DC) 2.Plug the AC power adapter into a 100V~240V power source. Connect the wall-plug adapter to your Mini PC: NOTE: The power adapter may vary in appearance, depending on the model and your region. Connect a display monitor to your Mini PC: Connect one end of an HDMI cable to an external display, and the other end of the cable to your Mini PC’S HDMI port. Connect a keyboard and mouse to your Mini PC: You can connect most of the USB keyboard and mouse to your Mini PC. You can also connect a USB dongle for a wireless keyboard and mouse set. Turn on your Mini PC Press the power button to turn on your Mini PC. Turning off your Mini PC If your Mini PC is unresponsive, press and hold the power button for at least four seconds until your Mini PC turns off. WARNING! Bios (Basic input and output system) stores system hardware settings that are needed for syste…

Text truncated - open the document above for the full version.

YEAHER INC. 51 Steel Dr, Unit A,New Castle Delaware United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-6-13 To whom it may concern: We, YEAHER INC., hereby certify that the equipment for which authorization is sought (FCC ID: 2BEMH-MME1R) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature Jingjun LIU Manager YEAHER INC. 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

YEAHER INC. 51 Steel Dr, Unit A,New Castle Delaware United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-6-13 U.S. Agent Designation YEAHER INC. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BEMH-MME1R): Name and company of U.S. agent: YEAHER INC. Physical U.S. address of agent: 51 Steel Dr, Unit A,New Castle Delaware United States FRN of U.S. agent: 0034764837 Email address of U.S. agent: [email protected] YEAHER INC. acknowledges their obligation to accept service of process on behalf of YEAHER INC.. YEAHER INC. with the FRN [0034764837] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Jingjun LIU Manager YEAHER INC. Signature Jingjun LIU Manager YEAHER INC. 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

YEAHER INC. Add: 51 Steel Dr, Unit A,New Castle Delaware United States Date: 2024-6-13 FCC ID: 2BEMH-MME1R Dear Sir/Madam, We, YEAHER INC. Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: MINI PC Model no.: MME1R, MME1B Sincerely, Name/Title： Jingjun LIU/Manager Company: YEAHER INC. Address: 51 Steel Dr, Unit A,New Castle Delaware United States Phone: (135) 382-1814 Fax: N/A E-Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-6-13> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2BEMH-MME1R MME1R For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Jingjun LIU/Manager Company: YEAHER INC. Address: 51 Steel Dr, Unit A,New Castle Delaware United States Phone: (135) 382-1814 Fax: N/A E-Mail: [email protected]

YEAHER INC. 51 Steel Dr, Unit A,New Castle Delaware United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-6-13 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BEMH-MME1R including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Jingjun LIU/Manager Company: YEAHER INC. Address: 51 Steel Dr, Unit A,New Castle Delaware United States Phone: (135) 382-1814 Fax: N/A E-Mail: [email protected]

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 1 of 4 Product Name: MINI PC Model No.: MME1R EUT Constructional Details External Photo Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 2 of 4 Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 3 of 4 Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 4 of 4 ------End------

DNB1 铭牌 1、材质：消银龙（50#）不干胶；表面覆可打印哑膜；尺寸：50x30mm 来料为卷装 Label 50 mm 30mm Company：Nimo Direct Inc. Address：New Castle，Delaware Web： www.nimopc.com Origin：Made in China Product Name：Nimo Mini PC Product Model：MME1R Input: 12V 3A FCC ID：2BEMH-MME1R SN: SN:XXXXXXXXXX

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 1 of 3 Product Name: MINI PC Model No.: MME1R EUT Constructional Details Internal Photo ANTENNA 1 ANTENNA 2 Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 2 of 3 Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 3 of 3 ------End------

RF Exposure evaluation FCC ID: 2BEMH-MME1R Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Mobile Device 1. Reference According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. KDB447498 D01: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 2. Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 1842/f 61.4 / / 1.63 4.89/f 0.163 / / (100) * (900/f 2 )* 1.0 f/300 5 6 6 6 6 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 824/f 27.5 / / 1.63 2.19/f 0.073 / / (100) * (180/f 2 )* 0.2 f/1500 1.0 30 30 30 30 30 F=frequency in MHz *=Plane-wave equivalent power density 3. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. Antenna Information MME1R can only use antennas certificated as follows provided by manufacturer; Antenna No. Model No. of antenna: Type of antenna: Gain of the antenna (Max.) Frequency range: BT / FPC Antenna 0.34dBi for 2400-2500MHz; 2.4GWIFI / FPC Antenna 0.34dBi for 2400-2500MHz for ANT 1 3.43dBi for 2400-2500MHz for ANT 2 5GWIFI / FPC Antenna 3.73dBi for 5000-6000MHz for ANT 1 3.61dBi for 5000-6000MHz for ANT 2 5. Manufacturing Tolerance Mode Max. Peak Conducted Output Power (dBm) Max. tune-up BT 1.05 1.0±1 BLE 5.1 5.0±1 Mode Max. Peak Conducted Output Power (dBm) Max. tune-up Antenna0 Antenna1 Antenna0 Antenna1 2.4GWIFI 22.48 19.66 22.0±1 20.0±1 Mode Max. Average Conducted Output Power (dBm) Max. tune-up Antenna0 Antenna1 Antenna0 Antenna1 5.2GWIFI 11.59 11.42 11±1 11±1 5.8GWIFI 11.03 11.76 11±1 11±1 6. Standalone MPE Result As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the gain of the used antenna is refer to section 4, the RF power density can be obtained. Modulation Type Output power Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm 2 ) MPE Limits (mW/cm 2 ) dBm mW BT 2.0 1.5849 0.34 1.0814 0.0003 1.0000 BLE 6.0 3.9811 0.34 1.0814 0.0009 1.0000 2.4GWIFI ANT1 23.0 199.5262 0.34 1.0814 0.0429 1.0000 5.2GWIFI ANT1 12.0 15.8489 3.73 2.3605 0.0074 1.0000 5.8GWIFI ANT1 12.0 15.8489 3.73 2.3605 0.0074 1.0000 Modulation Type Output power Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm 2 ) MPE Limits (mW/cm 2 ) dBm mW 2.4GWIFI ANT2 21.0 125.8925 3.43 2.2029 0.0552 1.0000 5.2GWIFI ANT2 12.0 15.8489 3.61 2.2961 0.0072 1.0000 5.8GWIFI ANT2 12.0 15.8489 3.61 2.2961 0.0072 1.0000 Remark: 1. Output power (Peak) including turn-up tolerance; 2. MPE evaluate distance is 20cm from user manual provide by manufacturer. 7. simultaneous MPE Result 2.4GWIFI ANT1 MPE (Ratio) 2.4GWIFI ANT2 MPE (Ratio) simultaneous MPE (Ratio) MPE Limits (Ratio) 0.0429 0.0552 0.0981 1.0000 8. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device. ----------------THE END OF REPORT---------------

规 格 承 认 书 SPECIFICATION FOR APPROVAL 日期 2024.05.29DATE: 版本 AREV.: 客 户 上海六联智能科技有限公司 CUSTOMER: 客 户 料 号 M.T.A.0000697 CUSTOMER P/N: 内置 2.4G&5G WiFi FPC天线，1.13白色普通线L=145mm with RF CONN(4代) for DNB1 主天线 品 名 PART NAME: 供 方 料 号 6241F00035 SUPPLIER P/N: 送样日期Date: 送样数量Q’TY:Pcs 客户确认CUSTOMER APPROVED BY 核准 Approvaled by 审核 Checked by 确认 Confirmed by 供方确认SUPPLIER SIGNATURE 核准 Approvaled by 审核 Checked by 拟制 Prepared by AndyCindy ZX-QT-RD-0011-A1 Add:上海市徐汇区桂箐路69号30栋603室 Tel:021-54266190 Fax:021-54266191 Contents ItemDescriptionPage 1. ..................Cover.................. 1 2. ..................Content.................. 2 3. ..................Drawing.................. 3 4. ..................... Antenna Test Report ............... 4~16 FILE: 6 5 4 3 2 NO DRAWING CHECKED APPROVED SHEET: 1/1 UNIT REV mm X3 DESCRIPTION CUSTOMER: PART NO: Z&X P/NO: PART NAME: 1 A B C DE 5 6 Q'TY REMARK 2 3 4 1 F REV DATE DESCRIPTION G CUSTOMER'S SIGNATURE X1 New Issue 05/07-2024 .XX ±0.2 ±0.3 ±0.5 ±1.0 ±2.0 .X X. XX. XXX. Signal Plus Technology Co.,Ltd. 上海增信电子有限公司 1 2 Antenna FPC board,Black solder resist ink 1 1 Cable 502-1-0624-X1 3 1 Connector IPEX-4 compatible;Gold-Plated X2 Update drawing 05/08-2024 2.4G&5G WiFi for DNB1 主端口 1.13 Coaxial cable;Color:White(白色) 6241F00035 X3 Update drawing 05/29-2024 M.T.A.0000697 焊接时 端子朝向依图（侧下方） 允许转动±75° *29.5±0.2 0624-X1-DNB1 11.9±0.2 *14.4±0.2 13.6±0.2 1 此处焊接 0.25±0.05 天线版本(白字) 背胶切断线 (20) 4.9±1 Ø3.5 *145±5(白色) 23 (1.2) 1.ELECTRICAL PROPERTIES： 1.1 Frequency Range.......2.4~2.5&5.15~5.85GHz 1.2 Impendance............50 Ohm Nominal 1.3 VSWR..................≤[email protected]~3.1GHz; ≤[email protected]~5.8GHz(only single antenna tested) 2.These Products are in conformity with ROHS2.0 3.Strict size is marked with "*",and () for reference. 2024.5.9 Antenna Test Report WIFI 2G & 5G ©V1 Signal Plus Technology Co., Ltd List of contents Test setup Antenna Solution S Parameter --- Return Loss、Isolation Efficiency and Peak Gain Radiation Patterns Summary Signal Plus Antennas 1.Test system description---S Parameter 1.1.Test Setup 1.1.1 VNA Test Setup S parameter measurements (S 11 ) were performed using an KeySight E5071C Network Analyzer and previously described tests fixtures. The isolation between antennas is also tested. The testing was performed with apparatus in free space. Signal Plus Antennas 1.1.2 Anechoic Chamber Test Setup The gain of the antenna was measured in the anechoic chamber(ETS-3D). The chamber provides less than –30 dB reflectivity from 400 MHz through 6 GHz. The chamber size is:7m*4m*3m.The measurement results are calibrated using a leaky wave horn standard. We can measure the antenna gain and efficiency accurately. +Z +Y +X Horn Antenna Signal Plus Antennas 1.Test system description--- Anechoic Chamber Test Setup X Z--in X Y 1.1.3 Instruments R&S CMW500 4G/WIFI （LTE/WIFI b/g/a） Agilent 8960 2G/3G （GSM/CDMA/WCDMA） KeySight E5071C (400MHz~6GHz) Signal Plus Antennas 1.Test system description--- Test Instruments 2. Antenna Solution 2.1 Antenna Location Pictures for passive Signal Plus Antennas 长线- Main Antenna 短线- AUX Antenna 3.Test Result--- Return Loss、 Efficiency、Gain S11(长线)： Signal Plus Antennas 3.Test Result--- Return Loss、 Efficiency、Gain Data ： Signal Plus Antennas Freq. (MHz) Gain (dBi) Efficiency (%) 2400.0 -0.86 30.0% 2450.0 -0.38 32.0% 2500.0 0.34 36.9% 5150.0 3.73 46.1% 5250.0 3.51 44.2% 5350.0 2.09 44.1% 5450.0 0.31 38.9% 5550.0 1.22 36.8% 5650.0 0.95 39.3% 5750.0 0.76 37.7% 5850.0 -0.11 31.4% 3.Test Result--- Return Loss、 Efficiency、Gain Radiation patterns： Signal Plus Antennas 3.Test Result--- Active data Signal Plus Antennas Mode Channel TRP TIS 2.4g 11g 54M 1 12.28 -69.26 6 12.46 -71.73 11 11.79 -71.11 5g 11a 54M 36 10.45 -71.36 100 13.75 -70.42 165 11.94 -69.39 4.Isolation Signal Plus Antennas 5.Summary 1.装天线时注意cable从主板的孔的下方穿过，如下图。 2.风扇cable需要固定下用来避开天线辐射区域。 Signal Plus Antennas 1.装天线时注意cable从 主板的孔的下方穿过 2.风扇cable需要固定下 用来避开天线辐射区域 5.Summary 3.天线位置图。 Signal Plus Antennas

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202405417F01 This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 45 TEST Report Applicant: YEAHER INC. Address of Applicant: 51 Steel Dr, Unit A, New Castle, DE 19720 United States Manufacturer : Nimo Direct Inc. Address of Manufacturer : 51 Steel Dr, Unit A, New Castle, DE 19720 United States Equipment Under Test (EUT) Product Name: MINI PC Model No.: MME1R Series model: MME1B Trade Mark: N/A FCC ID: 2BEMH-MME1R Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: May. 22, 2024 Date of Test: May. 22, 2024 ~ May. 28, 2024 Date of report issued: May. 28, 2024 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: HTT202405417F01 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Page 2 of 45 1. Version Version No. Date Description 00 May. 28, 2024 Original Tested/ Prepared By Date: May. 28, 2024 Project Engineer Check By: Date: May. 28, 2024 Reviewer Approved By : Date: May. 28, 2024 Authorized Signature Report No.: HTT202405417F01 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Page 3 of 45 2. Contents Page 1. VERSION ........................................................................................................................................................ 2 2. CONTENTS .................................................................................................................................................... 3 3. TEST SUMMARY ........................................................................................................................................... 4 4. GENERAL INFORMATION ............................................................................................................................ 5 4.1. GENERAL DESCRIPTION OF EUT ................................................................................................................ 5 4.2. TEST MODE ............................................................................................................................................... 7 4.3. DESCRIPTION OF SUPPORT UNITS .............................................................................................................. 7 4.4. DEVIATION FROM STANDARDS .................................................................................................................... 7 4.5. ABNORMALITIES FROM STANDARD CONDITIONS ........................................................................................... 7 4.6. TEST FACILITY ........................................................................................................................................... 7 4.7. TEST LOCATION ......................................................................................................................................... 7 4.8. ADDITIONAL INSTRUCTIONS ........................................................................................................................ 7 5. TEST INSTRUMENTS LIST ........................................................................................................................... 8 6. TEST RESULTS AND MEASUREMENT DATA ........................................................................................... 9 6.1. CONDUCTED EMISSIONS ............................................................................................................................ 9 6.2. CONDUCTED PEAK OUTPUT POWER ......................................................................................................... 12 6.3. 20DB EMISSION BANDWIDTH .................................................................................................................... 13 6.4. FREQUENCIES SEPARATION ..................................................................................................................... 17 6.5. HOPPING CHANNEL NUMBER .................................................................................................................... 19 6.6. DWELL TIME ............................................................................................................................................ 21 6.7. BAND EDGE ............................................................................................................................................. 26 6.7.1. Conducted Emission Method ......................................................................................................... 26 6.7.2. Radiated Emission Method ............................................................................................................ 30 6.8. SPURIOUS EMISSION ................................................................................................................................ 32 6.8.1. Conducted Emission Method ......................................................................................................... 32 6.8.2. Radiated Emission Method ............................................................................................................ 37 6.9. ANTENNA REQUIREMENT .......................................................................................................................... 44 7. TEST SETUP PHOTO ........................................................................................................................…

Text truncated - open the document above for the full version.

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 1 of 2 Product Name: MINI PC Model No.: MME1R Test Setup Photo Radiated Emission Report No.: HTT202405417 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 2 of 2 Conducted Emission ------End------