2BEMH-MPL1PMINI PC

9 The MPL1 is covered for a period of 2 years from the date the product was sold to an end-user for the first time, confirmed by the proof of purchase issued by the first retailer. During the warranty period, Proline or a Proline authorised service center will repair defects in materials and workmanship that result in product failure during normal usage free of charge and in a commercially reasonable time by either repairing or replacing your product at its option.If Proline replaces the product, the replace ment product will be subject to your rights set forth in this warranty for the remaining warranty period of the original product and the replacement product may be a refurbished product. The warranty is not valid if the product has been disassembled, modified or repaired without Proline's authorisation. Damage caused by neglect, either intentional or accidental, is not covered by warranty. Examples not covered by warranty include but are not limited to use outside operating specifications, a cracked or broken screen, cracked or damaged housing or cover, damaged or missing buttons, damaged ports or connectors, damage due to power surge or use of an incorrect power supply and water damage [as evidenced by inspection of the intemal liquid contact indicator). For warranty support or repair, please contact Customer Care line on 855-216-7257 email at [email protected] Website:www.nimopc.com tĂƌƌĂŶƚLJŝŶĨŽƌŵĂƟŽŶ NIMO Support MINI PC USER MANUAL FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: ЬReorient or relocate the receiving antenna. ЬIncrease the separation between the equipment and receiver. ЬConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

YEAHER INC. 51 Steel Dr, Unit A,New Castle Delaware United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-5-13 To whom it may concern: We, YEAHER INC., hereby certify that the equipment for which authorization is sought (FCC ID: 2BEMH-MPL1P) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature Jingjun LIU Manager YEAHER INC. 62_[model] CoveredEqu_2.911(d)(5 )(i) and (ii) - U, V03

YEAHER INC. 51 Steel Dr, Unit A,New Castle Delaware United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-5-13 U.S. Agent Designation YEAHER INC. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BEMH-MPL1P): Name and company of U.S. agent: YEAHER INC. Physical U.S. address of agent: 51 Steel Dr, Unit A,New Castle Delaware United States FRN of U.S. agent: 0034764837 Email address of U.S. agent: [email protected] YEAHER INC. acknowledges their obligation to accept service of process on behalf of YEAHER INC.. YEAHER INC. with the FRN [0034764837] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Jingjun LIU Manager YEAHER INC. Signature Jingjun LIU Manager YEAHER INC. 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

YEAHER INC. Add: 51 Steel Dr, Unit A,New Castle Delaware United States Date: 2024-5-13 FCC ID: 2BEMH-MPL1P Dear Sir/Madam, We, YEAHER INC. Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: MINI PC Model no.: MPL1P, MPL1W Sincerely, Name/Title： Jingjun LIU/Manager Company: YEAHER INC. Address: 51 Steel Dr, Unit A,New Castle Delaware United States Phone: (135) 382-1814 Fax: N/A E-Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-5-13> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2BEMH-MPL1P MPL1P For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Jingjun LIU/Manager Company: YEAHER INC. Address: 51 Steel Dr, Unit A,New Castle Delaware United States Phone: (135) 382-1814 Fax: N/A E-Mail: [email protected]

YEAHER INC. 51 Steel Dr, Unit A,New Castle Delaware United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-5-13 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BEMH-MPL1P including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Jingjun LIU/Manager Company: YEAHER INC. Address: 51 Steel Dr, Unit A,New Castle Delaware United States Phone: (135) 382-1814 Fax: N/A E-Mail: [email protected]

YEAHER INC. 51 Steel Dr, Unit A,New Castle Delaware United States UNII Device Declaration Letter To whom it may concern: We have declared below featured for FCC equipment authorization, Device FCC ID: 2BEMH-MPL1P (1) DFS Device: Master Client with Radar detection capability N/A Client without radar detection capability, (2) Active / Passive Scanning , adhoc mode access point capability Frequency Band (MHz) Active Scanning (the device can transmit a probe (beacon)) passive scanning (where the device is can listen only with no probes) Ad Hoc Mode capability Access point capability 5180-5240 Yes No Yes No Yes No Yes No 5190-5230 Yes No Yes No Yes No Yes No 5210-5210 Yes No Yes No Yes No Yes No 5745-5825 Yes No Yes No Yes No Yes No 5755-5795 Yes No Yes No Yes No Yes No 5775-5775 Yes No Yes No Yes No Yes No (3) Country code selection ability Yes No If yes, pls explain how it was implemented: (4) Meet 15.202 requirement Yes No pls check below : A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. (5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply Does not apply (If apply, pls help to provide explanation on it was implement, and how software was controlled) Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, (Signed) Name/Title： Jingjun LIU/Manager Company: YEAHER INC. Address: 51 Steel Dr, Unit A,New Castle Delaware United States Phone: (135) 382-1814 Fax: N/A E-Mail: [email protected]

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 1 of 4 Product Name: MINI PC Model No.: MPL1P EUT Constructional Details External Photo Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 2 of 4 Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 3 of 4 Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 4 of 4 ------End------

DNB20 铭牌 1、材质：消银龙（50#）不干胶；表面覆可打印哑膜；尺寸：50x30mm 来料为卷装 Label 50 mm 30mm Company：YEAHER INC. Address：New Castle，Delaware Web： www.nimopc.com Origin：Made in China Product Name：Nimo Mini PC Product Model：MPL1W Input: 12V 3A SN: SN:XXXXXXXXXX FCC ID: 2BEMH-MPL1P

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 1 of 5 Product Name: MINI PC Model No.: MPL1P EUT Constructional Details Internal Photo Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 2 of 5 Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 3 of 5 Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 4 of 5 Report No.: HTT202404147 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 5 of 5 ------End------

RF Exposure evaluation FCC ID: 2BEMH-MPL1P Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Mobile Device 1. Reference According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. KDB447498 D01: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 2. Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 1842/f 61.4 / / 1.63 4.89/f 0.163 / / (100) * (900/f 2 )* 1.0 f/300 5 6 6 6 6 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 824/f 27.5 / / 1.63 2.19/f 0.073 / / (100) * (180/f 2 )* 0.2 f/1500 1.0 30 30 30 30 30 F=frequency in MHz *=Plane-wave equivalent power density 3. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. Antenna Information MPL1P can only use antennas certificated as follows provided by manufacturer; Antenna No. Model No. of antenna: Type of antenna: Gain of the antenna (Max.) Frequency range: BT / FPC Antenna 3.11dBi for 2400-2500MHz; 2.4GWIFI / FPC Antenna 3.11dBi for 2400-2500MHz for ANT 1 1.42dBi for 2400-2500MHz for ANT 2 5GWIFI / FPC Antenna 0.32dBi for 5000-6000MHz for ANT 1 1.47dBi for 5000-6000MHz for ANT 2 5. Manufacturing Tolerance Mode Max. Peak Conducted Output Power (dBm) Max. tune-up BT -6.24 -6.0±1 BLE -0.55 0.0±1 Mode Max. Peak Conducted Output Power (dBm) Max. tune-up Antenna0 Antenna1 Antenna0 Antenna1 2.4GWIFI 20.28 21.03 20±1 21±1 Mode Max. Average Conducted Output Power (dBm) Max. tune-up Antenna0 Antenna1 Antenna0 Antenna1 5.2GWIFI 13.96 13.95 14±1 14±1 5.8GWIFI 13.22 13.35 14±1 14±1 6. Standalone MPE Result As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the gain of the used antenna is refer to section 4, the RF power density can be obtained. Modulation Type Output power Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm 2 ) MPE Limits (mW/cm 2 ) dBm mW BT -5.0 0.3162 3.11 2.0464 0.0001 1.0000 BLE 1.0 1.2589 3.11 2.0464 0.0005 1.0000 2.4GWIFI ANT1 21.0 125.8925 3.11 2.0464 0.0513 1.0000 5.2GWIFI ANT1 15.0 31.6228 0.32 1.0765 0.0068 1.0000 5.8GWIFI ANT1 15.0 31.6228 0.32 1.0765 0.0068 1.0000 Modulation Type Output power Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm 2 ) MPE Limits (mW/cm 2 ) dBm mW 2.4GWIFI ANT2 22.0 158.4893 1.42 1.3868 0.0437 1.0000 5.2GWIFI ANT2 15.0 31.6228 1.47 1.4028 0.0088 1.0000 5.8GWIFI ANT2 15.0 31.6228 1.47 1.4028 0.0088 1.0000 Remark: 1. Output power (Peak) including turn-up tolerance; 2. MPE evaluate distance is 20cm from user manual provide by manufacturer. 7. simultaneous MPE Result 2.4GWIFI ANT1 MPE (Ratio) 2.4GWIFI ANT2 MPE (Ratio) simultaneous MPE (Ratio) MPE Limits (Ratio) 0.0513 0.0437 0.095 1.0000 8. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device. ----------------THE END OF REPORT---------------

规 格 承 认 书 SPECIFICATION FOR APPROVAL 日期 2024.04.01DATE: 版本 AREV.: 客 户 上海六联智能科技有限公司 CUSTOMER: 客 户 料 号 CUSTOMER P/N: 内置 2.4G&5G WiFi FPC天线，0.81黑色普通线L=130mm with RF CONN(4代) for DNB20主端口 品 名 PART NAME: 供 方 料 号 6241F00021 SUPPLIER P/N: 送样日期Date: 送样数量Q’TY:Pcs 客户确认CUSTOMER APPROVED BY 核准 Approvaled by 审核 Checked by 确认 Confirmed by 供方确认SUPPLIER SIGNATURE 核准 Approvaled by 审核 Checked by 拟制 Prepared by AndyCindy ZX-QT-RD-0011-A1 Add:上海市徐汇区桂箐路69号30栋603室 Tel:021-54266190 Fax:021-54266191 Contents ItemDescriptionPage 1. ..................Cover.................. 1 2. ..................Content.................. 2 3. ..................Drawing.................. 3 4. ..................Antenna Test Report.................. 4~9 FILE: 6 5 4 3 2 NO DRAWING CHECKED APPROVED SHEET: 1/1 UNIT REV mm X1 DESCRIPTION CUSTOMER: PART NO: Z&X P/NO: PART NAME: 1 A B C DE 5 6 Q'TY REMARK 2 3 4 1 F REV DATE DESCRIPTION G CUSTOMER'S SINGATURE X1 New Issue 03/29-2024 .XX ±0.2 ±0.3 ±0.5 ±1.0 ±2.0 .X X. XX. XXX. 内置 2.4G&5G WiFi for DNB20主端口 Signal Plus Technology Co.,Ltd. 上海增信电子有限公司 1 2 Antenna FPC board,Black solder resist ink 1 1 1.ELECTRICAL PROPERTIES： 1.1 Frequency Range.......2.4~2.5&5.15~5.85GHz 1.2 Impendance..............50 Ohm Nominal 1.3 VSWR.......................≤[email protected]~5.85GHz(单天线检验) 2.These Products are in conformity with ROHS2.0 3.Strict size is marked with "*",and () for reference. Cable 0.81 Coaxial cable;Color:Black 6241F00021 502-1-0605-X1 3 1 Connector IPEX-4 compatible;Gold-Plated 0605-X1-NDB20-MAIN 天线标记 *14.0 ±0.2 *30.2±0.2 *130±5 Ø0.81 焊接时 端子朝向依图 允许转动±60° 1 2 3 此处焊接 0.24±0.05 Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com AntennaTestReport Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com 1.RFFixtureExperiment 1.1TestSetup 1.1.1VNATestSetup VSWRandReturnLossmeasurements(S11)wereperformedusingan KeySightE5071CNetworkAnalyzer.Theisolationbetweenantennasisalso tested.Thetestingwasperformedwithapparatusinfreespace. 1.1.2AnechoicChamberTestSetup Thegainoftheantennawasmeasuredintheanechoicchamber. Thechamberprovideslessthan–30dBreflectivityfrom400MHzthrough 6GHz.Thechambersizeis:7m*4m*3m.Themeasurementresultsare calibratedusingaleakywavehornstandard.Wecanmeasuretheantenna gainandefficiencyaccurately. +X +Z +Y Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com 2.AntennaSolution Mainantenna AUXantenna . Y X Z--out Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com Data Preview Main antenna Freq.(MHz)24002450250051505350555057505850 VSWR2.872.241.701.771.391.661.351.18 Gain(dBi) 1.84 3.112.950.32-1.32-0.52-0.91-1.79 Eff. %29.031.534.133.431.532.033.632.2 SWR and radiation patterns Main antenna S11 Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com Radiationpatterns: Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com 4.Activedata ModeChannelTRPTIS 5G11a/54m 3613.42-66.01 6413.64-65.21 16512.32-68.65 ModechannelTRPTIS 2.4G11g/54m 112.32-65.14 612.2-65.96 1112.03-66.31

规 格 承 认 书 SPECIFICATION FOR APPROVAL 日期 2024.04.01DATE: 版本 B REV.: 客 户 上海六联智能科技有限公司 CUSTOMER: 客 户 料 号 CUSTOMER P/N: 内置 2.4G&5G WiFi FPC天线，0.81灰色普通线L=170mm with RF CONN(4代) for DNB20副端口 品 名 PART NAME: 供 方 料 号 6241F00022 SUPPLIER P/N: 送样日期Date: 送样数量Q’TY:Pcs 客户确认CUSTOMER APPROVED BY 核准 Approvaled by 审核 Checked by 确认 Confirmed by 供方确认SUPPLIER SIGNATURE 核准 Approvaled by 审核 Checked by 拟制 Prepared by AndyCindy ZX-QT-RD-0011-A1 Add:上海市徐汇区桂箐路69号30栋603室 Tel:021-54266190 Fax:021-54266191 Contents ItemDescriptionPage 1. ..................Cover.................. 1 2. ..................Content.................. 2 3. ..................Drawing.................. 3 4. ..................Antenna Test Report.................. 4~9 此处焊接 0606-X1-NDB20-AUX *14.0 ±0.2 *30.2±0.2 0.24±0.05 FILE: 6 5 4 3 2 NO DRAWING CHECKED APPROVED SHEET: 1/1 UNIT REV mm X3 DESCRIPTION CUSTOMER: PART NO: Z&X P/NO: PART NAME: 1 A B C DE 5 6 Q'TY REMARK 2 3 4 1 F REV DATE DESCRIPTION G CUSTOMER'S SINGATURE X1 New Issue 03/29-2024 .XX ±0.2 ±0.3 ±0.5 ±1.0 ±2.0 .X X. XX. XXX. 内置 2.4G&5G WiFi for DNB20副端口 Signal Plus Technology Co.,Ltd. 上海增信电子有限公司 1 2 Antenna FPC board,Black solder resist ink 1 1 1.ELECTRICAL PROPERTIES： 1.1 Frequency Range.......2.4~2.5&5.15~5.85GHz 1.2 Impendance..............50 Ohm Nominal 1.3 VSWR.......................≤[email protected]~5.85GHz(单天线检验) 2.These Products are in conformity with ROHS2.0 3.Strict size is marked with "*",and () for reference. Cable 0.81 Coaxial cable;Color:Gray(灰色) 6241F00022 502-1-0606-X1 3 1 Connector IPEX-4 compatible;Gold-Plated *170±5 Ø0.81 焊接时 端子朝向依图 允许转动±90° 2 3 X2 修改线材颜色 04/01-2024 X3 修改线材颜色 04/01-2024 Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com AntennaTestReport Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com 1.RFFixtureExperiment 1.1TestSetup 1.1.1VNATestSetup VSWRandReturnLossmeasurements(S11)wereperformedusingan KeySightE5071CNetworkAnalyzer.Theisolationbetweenantennasisalso tested.Thetestingwasperformedwithapparatusinfreespace. 1.1.2AnechoicChamberTestSetup Thegainoftheantennawasmeasuredintheanechoicchamber. Thechamberprovideslessthan–30dBreflectivityfrom400MHzthrough 6GHz.Thechambersizeis:7m*4m*3m.Themeasurementresultsare calibratedusingaleakywavehornstandard.Wecanmeasuretheantenna gainandefficiencyaccurately. +X +Z +Y Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com 2.AntennaSolution Mainantenna AUXantenna . Y X Z--out Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com DataPreview AUXantenna Freq.(MHz)24002450250051505350555057505850 VSWR1.311.291.651.421.151.421.411.79 Gain(dBi) -0.38 0.931.421.470.870.62-0.64-1.00 Eff.%31.230.532.238.636.536.432.929.4 AUXantenna S11 Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com Radiationpatterns: Tel:021-54266190Fax:021-54266191Web:www.zxsignal.com 4.Activedata ModeChannelTRPTIS 5G11a/54m 3613.42-66.01 6413.64-65.21 16512.32-68.65 ModechannelTRPTIS 2.4G11g/54m 112.32-65.14 612.2-65.96 1112.03-66.31

Shenzhen HTT Technology Co., Ltd. Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China FCC PART 15 SUBPART C TEST REPORT FCC PART 15 SUBPART E 15.407 Report Reference No. ..................... : FCC ID. ............................................ : HTT202404147F02 2BEMH-MPL1P Compiled by ( position+printed name+signature) .. : File administrators Supervised by ( position+printed name+signature) .. : Project Engineer Approved by ( position+printed name+signature) .. : RF Manager Date of issue ..................................... : Apr. 19, 2024 Testing Laboratory Name .............. : Shenzhen HTT Technology Co.,Ltd. Address ............................................ : 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao’an District, Shenzhen, Guangdong, China Applicant’s name ............................ : YEAHER INC. Address ............................................ : 51 Steel Dr, Unit A, New Castle, DE 19720 United States Test specification ...........................: Standard ........................................... : FCC Part 15 Subpart E 15.407 Shenzhen HTT Technology Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen HTT Technology Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen HTT Technology Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: MINI PC Trade Mark ....................................... : N/A Manufacturer .................................... : Nimo Direct Inc. Model/Type reference....................... : MPL1P Listed Models .................................. : MPL1W Modulation ....................................... : OFDM Frequency .......................................... From 5180MHz-5240MHz, 5745MHz-5825MHz Ratings ............................................. : DC 12.0V From External Circuit Result................................................ : PASS Report No.: HTT202404147F02 Page 2 of 56 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China T E S T R E P O R T Equipment under Test : MINI PC Model /Type : MPL1P Serial Models : MPL1W Applicant : YEAHER INC. Model Declaration : PCB board, structure and internal of these model(s) are the same, So no additional models were tested. Address : 51 Steel Dr, Unit A, New Castle, DE 19720 United States Manufacturer : Nimo Direct Inc. Address : 51 Steel Dr, Unit A, New Castle, DE 19720 United States Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: HTT202404147F02 Page 3 of 56 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Contents 1 T E S T S T A N D A R D S ................................................................. 4 2 S U M M A R Y ............................................................................ 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Equipment Under Test 5 2.4 Short description of the Equipment under Test (EUT) 5 2.5 EUT operation mode 6 2.6 Block Diagram of Test Setup 6 2.7 Related Submittal(s) / Grant (s) 6 2.8 Modifications 6 3 T E S T E N V I R O N M E N T .............................................................. 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Environmental conditions 7 3.4 Test Description 8 3.5 Statement of the measurement uncertainty 8 3.6 Equipments Used during the Test 9 4 T E S T C O N D I T I O N S A N D R E S U L T S ........................................... 10 4.1 AC Power Conducted Emission 10 4.2 Radiated Emissions 13 4.3 Maximum Conducted Average Output Power 20 4.4 Power Spectral Density 24 4.5 Emission Bandwidth (26dB Bandwidth) 38 4.6 Minimum Emission Bandwidth (6dB Bandwidth) 46 4.7 Frequency Stability 54 5 T E S T S E T U P P H O T O S O F T H E E U T ......................................... 56 6 P H O T O S O F T H E E U T ........................................................... 56 Report No.: HTT202404147F02 Page 4 of 56 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules Part 15 Subpart E—Unlicensed National Information Infrastructure Devices ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices KDB789033 D02: General UNII Test Procedures New Rules v01r02 Report No.: HTT202404147F02 Page 5 of 56 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China 2 S U M M A R Y 2.1 General Remarks Date of receipt of test sample : Apr. 11, 2024 Testing commenced on : A…

Text truncated - open the document above for the full version.