2BH5P-QIS213-in-1 Wireless Charging Station

FCC warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Avertissement FCC : Tout changement ou modification non expressément approuvé par la partie responsable de la conformité peut annuler le droit de l'utilisateur à utiliser cet appareil. Remarque : Cet appareil est conforme à la partie 15 du règlement FCC. Son utilisation est soumise aux deux conditions suivantes : (1) Cet appareil ne doit pas produire d'interférences nuisibles ; (2) Cet appareil doit accepter toute interférence reçue, y compris celles susceptibles d'entraîner un fonctionnement indésirable. Ces limites sont conçues pour offrir une protection raisonnable contre les interférences nuisibles dans une installation domestique. Cet équipement génère, utilise et peut émettre de l'énergie radiofréquence. S'il n'est pas installé et utilisé conformément aux instructions, il peut provoquer des interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie qu'aucune interférence ne se produira dans une installation donnée. Si cet équipement crée des interférences nuisibles à la réception radio ou télévisée (vérifiable en éteignant puis en rallumant l'appareil), l'utilisateur est invité à corriger ces interférences par l'une ou plusieurs des mesures suivantes : -Réorienter ou déplacer l'antenne de réception. -Augmenter la distance entre l'équipement et le récepteur. -Brancher l'appareil sur une prise appartenant à un circuit électrique différent de celui du récepteur. -Consulter le revendeur ou un technicien radio/télévision qualifié pour obtenir de l'assistance. Cet équipement respecte les limites d'exposition aux rayonnements FCC définies pour un environnement non contrôlé. L'appareil doit être installé et utilisé en respectant une distance minimale de 20 cm entre l'émetteur et le corps humain.

Label, Label location Label location

Page 1 of 2 FCC ID: 2BH5P-QIS21 Test Photo Page 2 of 2

Antenna Specifications 1. Manufacture: SHENGZHEN XIANGRUIDA SCI.CO., LTD. Adress: A605, Building 5, Longxi Yayuan, No. 1, Lingnan Road, Longxi Community, Longgang Street, Longgang District, Shenzhen 2. Material Specifications: XYDG2502 3. Floor plan unit: MM 4. Product parameters Line diameter: 0.08*24P Number of turns: 13TS

Antenna Specifications 1. Manufacture: SHENGZHEN XIANGRUIDA SCI.CO., LTD. Adress: A605, Building 5, Longxi Yayuan, No. 1, Lingnan Road, Longxi Community, Longgang Street, Longgang District, Shenzhen 2. Material Specifications: 43.5*0.6 double slot hot air 0.08*24*2P wire length 5MM 3. Floor plan unit: MM A B C D E F 43.5±0.5 38±1 2 Max 20±0.5 15±2 3±1 4. Product parameters Line diameter: 0.08*24*2P Number of turns: 12TS

Antenna Specifications 1. Manufacture: SHENGZHEN XIANGRUIDA SCI.CO., LTD. Adress: A605, Building 5, Longxi Yayuan, No. 1, Lingnan Road, Longxi Community, Longgang Street, Longgang District, Shenzhen 2. Material Specifications: 43.5*0.6 double slot wire wrap, 0.07*100 wire length, 180MM 3. Floor plan unit: MM A B C D1 D2 E F H 40.0±0.5 20.5±0.5 1.0±0.5 23.7±0.5 21.5±2 3±1 43.0±1 1.7±0.5 4. Product parameters Line diameter: 0.08*105P Number of turns: 10TS

ShenzhenBKCTestingCo.,Ltd.ReportNo.:BKC26063552FE-1 TestReportTel:4000-875-3820755-84829082Web:Http://www.bkc-lab.comPage1of21 TESTREPORT Applicant:ShenzhenFragewayTechnologyCO.,LTD Address: Room303,Building2,No.13TianyuanRoad,DongfangCommunity, SonggangStreet,Bao'anDistrict,Shenzhen Manufacturer: ShenzhenFragewayTechnologyCO.,LTD Address: Room303,Building2,No.13TianyuanRoad,DongfangCommunity, SonggangStreet,Bao'anDistrict,Shenzhen ProductName:3-in-1WirelessChargingStation ModelNumber:MI-QIS21,QIS21-035-7458-8 Trademark: , FCCID:2BH5P-QIS21 TestDate: Jun.10,2026–Jun.24,2026 DateofReport: Aug.11,2026 TestResult: ThisdevicedescribedabovehasbeentestedbyBKC,andthetest resultsshowthattheequipmentundertest(EUT)isincompliance withtheStandardrequirements.Anditisapplicableonlytothetested sampleidentifiedinthereport. TestProcedureUsed: Standards:FCCCFRTitle47Part15SubpartC ANSIC63.10-2020+Cor.1-2023+C63.10a-2024+Erratato C63.10a-2024 Preparedby(TestEngineer): CareyZheng Reviewer(Supervisor): CaseyWang Approved(Manager): LeviXiao ShenzhenBKCTestingCo.,Ltd.ReportNo.:BKC26063552FE-1 TestReportTel:4000-875-3820755-84829082Web:Http://www.bkc-lab.comPage2of21 TABLEOFCONTENT 1.GeneralInformation......................................................................................4 1.1.DescriptionofDevice(EUT).......................................................................................................................4 1.2.ChannelList..................................................................................................................................................4 1.3.Summaryoftestresult................................................................................................................................4 1.4.SpecialAccessoriesandAuxiliaryEquipment........................................................................................4 1.5.Testmode......................................................................................................................................................5 1.6.BlockDiagram...............................................................................................................................................5 1.7.TestConditions.............................................................................................................................................5 1.8.MeasurementUncertainty(95%confidencelevels,k=2)......................................................................6 1.9.TestFacility....................................................................................................................................................6 1.10.TestEquipment...........................................................................................................................................6 2.Conductedemissionatthemainsterminalstest......................................8 2.1.Limit................................................................................................................................................................8 2.2.TestSetup......................................................................................................................................................8 2.3.TestProcedure..............................................................................................................................................8 2.4.TestResult.....................................................................................................................................................9 4.RadiatedSpuriousEmissions...................................................................11 4.1.Limit..............................................................................................................................................................11 4.2.TestSetup....................................................................................................................................................12 4.3.TestProcedure............................................................................................................................................14 4.4.TestResult...................................................................................................................................................15 5.-20dBBandwidthMeasurement...............................................................19 5.1.Limit..............................................................................................................................................................19 5.2.TestSetup....................................................................................................................................................19 5.3.TestProcedure............................................................................................................................................19 5.4.TestResult...................................................................................................................................................19 6.AntennaRequirement.................................................................................21 ShenzhenBKCTestingCo.,Ltd.ReportNo.:BKC26063552FE-1 TestReportTel:4000-875-3820755-84829082Web:Http://www.bkc-lab.comPage3of21 RevisionHistoryofThisTestReport ReportNumberDescriptionIssuedDate BKC26063552FE-1InitialIssue2026-08-11 ShenzhenBKCTestingCo.,Ltd.ReportNo.:BKC26063552FE-1 TestReportTel:4000-875-3820755-84829082Web:Http://www.bkc-lab.comPage4of21 1.GeneralInformation 1.1.DescriptionofDevice(EUT) EUTName: 3-in-1WirelessChargingStation ModelNo.:MI-QIS21,QIS21-035-7458-8 ModelDifference:Allmodelsareidenticaltoeachotherexceptformodelnameandcolor.Alltests areperformedonmodelMI-QIS21 Powersupply:Input:5V/3A,9V/3A Output:Output#1(iPhone):5W/7.5W/10W/15W Output#2(Airpods):5W Output#3(AppleWatch):2.5W Operationfrequency:110.5-205KHzforiPhoneandAirpods 320-330kHzforAppleWatch Max.RFoutputpower:: 48.23dBuV/m Modulation:…

Text truncated - open the document above for the full version.

Shenzhen BKC Testing Co., Ltd. Report No.: BKC26063552FE-2 FCC ID: 2BH5P-QIS21 Product Name: 3-in-1 Wireless Charging Station Product Model No.: MI-QIS21, QIS21-035-7458-8 Model Difference: All models are identical to each other except for model name and color. All tests are performed on model MI-QIS21 Transmitting mode Keep the EUT in continuously wireless charging mode Power supply: Input:5V/3A, 9V/3A Output: Output #1 (iPhone): 5W / 7.5W / 10W / 15W Output #2 (Airpods): 5W Output #3 (Apple Watch): 2.5W Operation frequency : 110.5-205KHz for iPhone and Airpods 320-330kHz for Apple Watch Antenna Type: Coil Antenna Test Modes: Mode 1 EUT Wireless charging(iPhone:5W+Airpods:5W+Apple Watch:2.5W) Mode 2 EUT Wireless charging(iPhone:5W+Airpods:5W) Mode 3 EUT Wireless charging(iPhone:5W+ Apple Watch:2.5W) Mode 4 EUT Wireless charging(Airpods:5W+Apple Watch:2.5W) Mode 5 EUT Wireless charging(iPhone:15W) Mode 6 EUT Wireless charging(iPhone:10W) Mode 7 EUT Wireless charging(iPhone:7.5W) Mode 8 EUT Wireless charging(iPhone:5W) Mode 9 EUT Wireless charging(Airpods:5W) Mode 10 EUT Wireless charging(Apple Watch:2.5W) Note: All test modes were pre-tested, but we only recorded the worst case (Mode 1) in this report. Auxiliary Equipment: Description Manufacturer Model No. S/N Remark Adapter APPLE A2244 F1625O31EBDPMG9DK / Phone APPLE iPhone 13 / / AirPods APPLE AirPods 2 / iWatch APPLE iWatch 5 / Shenzhen BKC Testing Co., Ltd. Report No.: BKC26063552FE-2 RF Exposure Evaluation 1 Measuring Standard KDB 680106 D01 Wireless Power Transfer v04 2 Requirements According to the item 5 of KDB 680106 D01 v04: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) 3 Test Setup Shenzhen BKC Testing Co., Ltd. Report No.: BKC26063552FE-2 4 Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The measurement probe was placed at test distance (15 cm from all sides and 20 cm from the top) which is between the edge of the charger and the geometric center of probe. 3) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E) were completed. 4) The EUT was measured according to the dictates of KDB 680106 D01 v04. Remark: The EUT’s test position A, B, C, D and E is valid for the E and H field measurements. 5 Test Instruments list Test Equipment Manufacturer Model No. SN. Cal.Date Cal.Due date Exposure Level Tester HIOKI HIOKI-3470-01 071016320 Dec. 31 2025 Dec. 30 2026 100 cm2 Magnetic Field Sensor HIOKI 100cm 2 sensor 0376-B1 Dec. 31 2025 Dec. 30 2026 6 Test Result E-Filed Strength at 15 cm from the edges surrounding the EUT (V/m) Test Mode Test Position A Test Position B Test Position C Test Position D Limits (V/m) Mode 1 2.62 2.54 2.57 2.61 614 E-Filed Strength at 20 cm from the top of the EUT (V/m) Test Mode Test Position E Limits (V/m) Mode 1 2.70 614 H-Filed Strength at 20 cm from the edges surrounding the EUT (A/m) Test Mode Test Position A Test Position B Test Position C Test Position D Limits (A/m) Mode 1 0.16 0.19 0.11 0.13 1.63 H-Filed Strength at 20 cm from the top of the EUT (A/m) Test Mode Test Position E Limits (A/m) Mode 1 0.15 1.63 Note: The EUT of 1%, 50%, 99% have test, the worst case (Mode 1: 1%) recorded in this report.

Page 1 of 6 FCC ID: 2BH5P-QIS21 Internal Photos Coil antenna for Airpods Page 2 of 6 Page 3 of 6 Page 4 of 6 Coil antenna for iPhone Page 5 of 6 Coil antenna for iPhone Page 6 of 6

ShenzhenFragewayTechnologyCO.,LTD ReferenceNo.2026UL0251 2.911(d)(7)USAAgentv1.3 Section2.911(d)(7)USAAgentforServiceofProcess Companyname:ShenzhenFragewayTechnologyCO.,LTD FCCID:2BH5P-QIS21 ContactName:EvanXu Address:Room303,Building2,No.13TianyuanRoad,DongfangCommunity, SonggangStreet,Bao’anDistrict,Shenzhen TelephoneNo:+8613510650464 Email:[email protected] 2.911(d)(7)USADesignatedAgentforServiceofProcess We,[ShenzhenFragewayTechnologyCO.,LTD](“theapplicant”)designate[TTS MARKETINC.] NOTE1 forthepurposeofacceptingserviceofprocessonbehalfofthe applicant. Applicantconsent:WeAcknowledgeourconsenttoacceptserviceofprocessinthe UnitedStatesformattersrelatedtotheapplicableequipment,andatthephysicalU.S. addressandemailaddressofthedesignatedagentandacknowledgeour acceptanceofourobligationtomaintainanagentforserviceofprocessintheUnited Statesfornolessthanoneyearaftereitherthegranteehaspermanentlyterminated allmarketingandimportationoftheapplicableequipmentwithintheU.S.,orthe conclusionofanyCommission-relatedadministrativeorjudicialproceedinginvolving theequipment,whicheverislater. Agentobligation:WeAcknowledgeourobligationtoacceptserviceofprocessinthe UnitedStatesformattersrelatedtotheapplicableequipmentatourphysicalU.S. addressandemailaddressfornolessthanoneyearaftereitherthegranteehas permanentlyterminatedallmarketingandimportationoftheapplicableequipment withintheU.S.,ortheconclusionofanyCommission-relatedadministrativeorjudicial proceedinginvolvingtheequipment,whicheverislater. USAAgent Companyname:TTSMARKETINC. Address:1178BroadwaySte324,NewYork, NY10001,USA FRN:0036806057 ContactName:MaverickLim TelephoneNo:：001-(646)305-2908 Email:[email protected] Applicant Companyname:ShenzhenFrageway TechnologyCO.,LTD Address:Room303,Building2,No.13 TianyuanRoad,DongfangCommunity, SonggangStreet,Bao’anDistrict, Shenzhen FCCRegistrationNumber(FRN): 0035778489 ShenzhenFragewayTechnologyCO.,LTD ReferenceNo.2026UL0251 2.911(d)(7)USAAgentv1.3 FCCGranteeCode:2BH5P ContactName:EvanXu TelephoneNo:+8613510650464 Email:[email protected] Signature: Title:Manager Signature: Title:Generalmanager Date:2026.08.18Date:2026.08.18 NOTE1:AnapplicantlocatedintheUnitedStatesmaydesignateitselfastheagentforservice ofprocess. Reference;FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

Page 1 of 4 FCC ID: 2BH5P-QIS21 External Photos Page 2 of 4 Page 3 of 4 Page 4 of 4

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Shenzhen Frageway Technology CO.,LTD Address: Room 303,Building 2,No. 13 Tianyuan Road, Dongfang Community, Songgang Street, Bao'an District, Shenzhen Product Name: 3-in-1 Wireless Charging Station Model Number: MI-QIS21, QIS21-035-7458-8 FCC Identifier: 2BH5P-QIS21 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Evan Xu Date: 2026.08.11 Title: General manager Signature of applicant:

C5266091_X10_Ed.2 1/1 < Shenzhen Frageway Technology CO.,LTD > Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2026.08.11 Subject: Request for Confidentiality FCC ID: 2BH5P-QIS21 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name:Evan Xu Title: General manager

TCB CALL página 1 File FCC ID: 2BH5P-QIS21 Please upload an exhibit that explains how does the TCB verify the new agent information: 1- Is the address of the agent a valid physical US mailing address (not a US post office box, not a virtual mailbox, not P.O. Boxes, not a vacant lot, not a public building, etc.) ○ We have checked if the address exists in a real and potential building (Google maps) + official US register, after this verification and the evidence below we can guarantee the following: not a US post office box not a virtual mailbox not P.O. Boxes not a vacant lot not a public building(note) ► We checked the FCC FRN Search based on the information provided by the grantee. On the official register from : https://apps.dos.ny.gov/publicInquiry/EntityDisplay Google: TCB CALL página 2 State of New York department of State: TCB CALL página 3 TCB CALL página 4 ► CONCLUSION by TCB: The ASOP defined and provided by grantee is VALID and confirmed. Therefore the exhibit "FU0944- J#UL0251,AMERICAN REPRESENTATIVE FCC LETTER OF ATTESTATION ID 2BH5P-QIS21(2026.08.17)" included in the file is ok. 2- Is the agent physically located at that valid US address such that the agent can be legally served at that address? Yes , check above 3- Has the listed agent clearly agreed in writing to serve as the agent for the grantee at that address? Yes, it is included in the exhibit "FU0944-J#UL0251,AMERICAN REPRESENTATIVE FCC LETTER OF ATTESTATION ID 2BH5P-QIS21(2026.08.17)"

Shenzhen Frageway Technology CO.,LTD Product Similarity Declaration Product name: 3-in-1 Wireless Charging Station Model name: MI-QIS21, QIS21-035-7458-8 FCC ID: 2BH5P-QIS21 We (Shenzhen Frageway Technology CO.,LTD) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), The only difference are the model name and color. Signature: Name: Evan Xu Title: General manager Place, date China, 2026.08.11

Shenzhen Frageway Technology CO.,LTD Code 00018768 Ed. 1 Device 3-in-1 Wireless Charging Station Company name Shenzhen Frageway Technology CO.,LTD Grantee code 2BH5P FCC ID 2BH5P-QIS21 FRN 0035778489 Contact name Evan Xu Address Room 303,Building 2,No. 13 Tianyuan Road, Dongfang Community, Songgang Street, Bao'an District, Shenzhen Telephone number +86-13510650464 E-mail [email protected] Chipset/module information R5550, R9813, RHX5352, R4608 Operating System (if applicable) N/A Storage Capacity (hard drive or other permanent memory storage, if applicable) N/A 2 Item 1. The device is able to install software/program installation? ☐ Yes, go to Item 2. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky cybersecurity or anti-virus software. Item 2. Technical Requirements for Kaspersky Cybersecurity Software: # General Requirements (For all Devices) Yes / No or N/A Comments 1 Internet connection for activation and updates (For all Operating Systems) N/A # General Requirements (For Windows Devices) Yes / No or N/A Comments 1 Storage: 1500 MB free space on the hard drive N/A 2 Operating System: Microsoft Windows 8, 8.1, 10 & 11 Home / Pro / Enterprise Microsoft Windows 7 Starter / Home Basic & Premium / Professional / Ultimate SP1 or higher N/A 3 Processor: 1 GHz or higher (x86 or x64) N/A 4 Memory (RAM)1 GB (32-bit) or 2 GB (64-bit) N/A 5 Screen Resolution: Minimum resolution of 1024 x 768 N/A # General Requirements (For macOS devices) Yes / No or N/A Comments 1 Operating System macOS® 13 – 14 N/A 2 Memory (RAM)4 GB N/A 3 Storage: 3455 MB free space on the hard drive N/A 3 # General Requirements (For Android Devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: Android™ 10 – 14 N/A 3 Screen Resolution: Minimum resolution of 320 x 480 N/A # General Requirements (for iOS devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: iOS® 17 N/A # General Requirements (For Linux system) Yes / No or N/A Comments 1 Hard drive: 1 GB of free space N/A 2 CPU: Intel Pentium 1 GHz or higher N/A 3 RAM: 1 GB N/A 4 Minimum software requirements: AlmaLinux OS 8 or later; AlterOS 7.5 or later; Astra Linux Common Edition 2.12 or later; CentOS 6.7 or later; Debian GNU/Linux 10.0 or later; EulerOS 2.0 or later; Oracle Linux 7.3 or later ; Red Hat Enterprise Linux 6.7 or later ; Rocky Linux 8.5 or later ; N/A 4 SUSE Linux Enterprise Server 12.5 or later; Ubuntu 12.04 or later ; Uncom OS Home / Business / Education / Enterprise 2.2 or later; ALT Linux Workstaton / Workstation K / Server / Education 8 or later; ROSA Linux Workstation / Server 12 or later ; RED OS 7.3 and later ; After reviewed the technical requirements, is the device capable of supporting the installation of Kaspersky software? installation of Kaspersky software Item 3. ☐Yes, go to Item 3. ☒No. In this case, the rest of the items do not apply. The device cannot support Connectivity Capabilities: # Physical Interface Purpose Justification 1 1 # Wireless Interface Purpose Justification 1 1 – additional third-party proof is provided to demonstrate compliance with requirements as of 2.911(d)5(i),(ii) – “Proof of Compliance with Covered List Software Requirements” of this After the review of this items, the device: ☒Cannot support installation of any cybersecurity or anti-virus software on the covered list .☐Potentially can operate with any cybersecurity or anti-virus software on the covered list document applies 1 The justification field is used to justify why the software cannot be received through that interface. Check the annex for more indications. 5 Signature: Name: Evan Xu Date: 2026.08.11

Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1 TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name:Shenzhen Frageway Technology CO.,LTD Grantee code: 2BH5P FCC ID: 2BH5P-QIS21 FRN: 0035778489 Contact Name: Evan Xu Address: Room 303,Building 2,No. 13 Tianyuan Road, Dongfang Community, Songgang Street, Bao'an District, Shenzhen Telephone No: 86-13510650464 Fax No:/ Email: [email protected] i. [Shenzhen Frageway Technology CO.,LTD] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Shenzhen Frageway Technology CO.,LTD] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Shenzhen Frageway Technology CO.,LTD] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment . Date: 2026/08/11 Applicant’s Name: Evan Xu Title: General manager Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist