2BOJ7-GANIC4CUBE

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. ICWarning -English:Thisdevicecontainslicence-exempttransmitter(s)/receiver(s)that complywithInnovation,ScienceandEconomicDevelopmentCanada’slicence- exemptRSS(s).Operationissubjecttothefollowingtwoconditions: 1.Thisdevicemaynotcauseinterference. 2.Thisdevicemustacceptanyinterference,includinginterferencethatmay causeundesiredoperationofthedevice. -French:Cetappareilcontientdesémetteurs/récepteursexemptés delicencequisontconformesauxRSSexemptésdelicenced’ innovation,sciencesetdéveloppementéconomiqueCanada.Le fonctionnementestsoumisauxdeuxconditionssuivantes: 1.Cetappareilnepeutpascauserd’interférences. 2.Cetappareildoitacceptertouteinterférence,ycomprisles interférencesquipeuventcauserunfonctionnementindésirabledel’ appareil. RadiationExposureStatement ThedevicehasbeenevaluatedtomeetgeneralRFexposurerequirement. Thedevicecanbeusedinportableexposureconditionwithoutrestriction. L'appareilaétéévaluépourrépondreauxexigencesgénéralesd' expositionauxradiofréquences.L'appareilpeutêtreutiliséenconditiond' expositionportablesansrestriction.

GANCUBEINC. Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,ShundeDistrict,Foshan, Guangdong,China AttestationStatements NotCoveredEntityApplicant&NotCoveredEquipment To:FederalCommunicationsCommissionDate:Nov.29,25 7435OaklandMillsRoad, Columbia,MD21046,USA Ref:InformationRequiredbySection2.911(d)(5)(i)&(ii) FCCID:2BOJ7-GANIC4 GANCUBEINC.(“theapplicant”)certifiesthat,asofthedateofthefilingoftheapplication,theapplicant isnotidentifiedontheCoveredList,establishedpursuantto§1.50002ofreferencechapter,asan entityproducing“covered”communicationequipment.Theequipmentforwhichauthorizationissought isnot“covered”telecommunicationsequipmentandvideosurveillanceequipmentproducedbyentities identifiedontheCommission’sCoveredListthatprohibitedfromreceivinganequipmentauthorization pursuanttosection§2.903oftheFCCrules. Sincerelyyours, ApplicantSignature PrintedName:EdwardLiang Title:Manager Address:Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,ShundeDistrict,Foshan, Guangdong,China Tel.:13527866242 Email:[email protected]

GANCUBEINC. Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,ShundeDistrict,Foshan, Guangdong,China 1|Page AttestationStatements To:FederalCommunicationsCommissionDate:Nov.29,25 7435OaklandMillsRoad, Columbia,MD21046,USA Subject:AttestationofCompliancewithFCCCoveredListSoftwareRequirements FCCID:2BOJ7-GANIC4 ProductName:CUBE Thisletterservesasanattestationthattheequipmentidentifiedabove☐is/☒isnot(selectone)"covered" softwareasdefinedundertheFederalCommunicationsCommission(FCC)CoveredListrequirements,as outlinedinFCC22-84andKDB986446. Specifically,theundersignedcertifiesthattheequipmentforwhichauthorizationissought: 1.Doesnotcontaincybersecurityoranti-virussoftwareproducedorprovidedbyKasperskyLab, Inc.oranyofitssuccessors,assignees,parents,subsidiaries,affiliates,oranyentitythathasrebranded orrelabeledsoftwareproducedbytheaforementionedentities. 2.Doesnothavethecapabilitytostore,run,ordeliveranysoftwareidentifiedontheFCCCoveredList, includingbutnotlimitedtocybersecurityandanti-virussoftware. Tosupportthisattestation,theappendixevaluationdocumentationhasbeenpreparedandisincludedinthe certificationfiling. Thisattestationisbasedonathoroughevaluationofthedevice'sdesign,functionality,andsoftware environment.Theundersignedaffirmsthattheinformationprovidedisaccurateandcompletetothebestof theirknowledge. Sincerelyyours, ApplicantSignature PrintedName:EdwardLiang Title:Manager Tel.:13527866242 Email:[email protected] GANCUBEINC. Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,ShundeDistrict,Foshan, Guangdong,China 2|Page EvaluationregardingtotheCoveredListSoftware: Compliance Methodology EvaluationProcessResults Deviceis Inherent compliance ☒ TheChipset(s)usedislimitedtorun theCybersecurityoranti-virus software. Compliance ☐ TheMemoryusedislimitedtorunthe Cybersecurityoranti-virussoftware. ☐ Thereisstoragecapacitylimitationfor storeorinstalltheCybersecurityor anti-virussoftware. ☐ Operatingsystemusedislimitedto run,installordelivertheCybersecurity oranti-virussoftware. Deviceisnot Inherent compliance ☐ EvaluationBasedonSoftware BillofMaterials(SBoM) ☐ EvaluationBasedonScanfor Softwareonthedevice ☐ EvaluationBasedonFilesystemscan ☐ EvaluationBasedonRunning softwarecheck

Local Representative Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(7), of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2BOJ7-GANIC4 GAN i carry 4, GAN 3X3 We hereby acknowledge as follows: i. both signees confirm that the point of contact accepts responsibility to act as a US- American Representative on behalf of the applicant ii. the point of contact provides the physical U.S. address and email as listed below iii. both parties maintain the requirements of this agreement for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. iv. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. US-American Point of Contact Applicant/Approval Holder Signature Date: 2025-11-24 Signature Date: 2025-11-24 Company Name: LOBOS IOWA INC GANCUBE INC FRN: 0036413961 0036869022 Contact Name: Harley Li Edward Liang Address: 4623 Bittercreek Dr Colorado Springs CO 80922 US Room 101-901, Building 2, CIMC Smart Park, No. 3 Chanxing Road, Shunde District, Foshan, Guangdong, China Phone: +1 8188180538 +86- 13527866242 Email: [email protected] [email protected]

GANCUBEINC. Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,ShundeDistrict,Foshan, Guangdong,China Date:Nov.29,25 FCCID:2BOJ7-GANIC4 ProductName:CUBE Model.:GANicarry4,GAN3X3 DearSir/Madam, We,GANCUBEINC.Herebydeclaresthefollowing: Allthemodelsareelectricalidenticalincludingthesamesoftwareparameterandhardware design(i.e.,circuitdesign,PCBLayout,RFmodule/circuit,antennatype(s)andantenna location,componentsonPCB,etc.,),onlyModelNameisdifference.: Sincerely, Name/Title:EdwardLiang/Manager Company:GANCUBEINC. Phone:13527866242 E-Mail:[email protected]

GANCUBEINC. Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,ShundeDistrict,Foshan, Guangdong,China Date:Dec.16,25 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Subject:ConfidentialityRequestfor:FCCID:2BOJ7-GANIC4 PursuanttoSections0.457and0.459oftheCommission’sRules,weherebyrequestpermanent confidentialtreatmentoftheexhibitsaccompanyingthiscertificationapplicationasoutlinedbelow: BlockDiagram  Schematics OperationalDescription  (Etc.) Theaboveexhibitscontaintradesecretsand/orproprietaryinformationthatarenotpubliclyavailableand materialsthattheApplicanthasspentconsiderableeffortsindeveloping.Publicdisclosureofthesemay beharmfultotheApplicantandgiveanunfairadvantagetocompetitorsonthemarket. Sincerelyyours, ApplicantSignature PrintedName:EdwardLiang Title:Manager Tel.:13527866242 Email:[email protected]

GANCUBEINC. Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,ShundeDistrict,Foshan, Guangdong,China Date:Nov.29,25 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Subject:AgentAuthorizationforFCCID:2BOJ7-GANIC4 I,theundersigned,herebyauthorizeDongguanYaxu(AiT)TechnologyLimitedtoactonourbehalfinall mattersrelatingtothisapplicationforequipmentcertification. AnyactcarriedoutbyDongguanYaxu(AiT)TechnologyLimitedshallhavethesameeffectasourown andIacknowledgethatallresponsibilityforcomplyingwiththetermsandconditionsofcertification,as specifiedbyDERYCOMCERTIFICATIONSERVICES,INC.,stillresideswithGANCUBEINC.. WecertifythatwearenotsubjecttoadenialoffederalbenefitsthatincludesFCCbenefitspursuantto Section5301oftheAnti-DrugAbuseActof1988,21U.S.C.§862,andthatnopartytotheapplication,as definedin47CFR§1.2002(b),issubjecttoadenialoffederalbenefitsthatincludesFCCbenefits pursuanttothatsection. Sincerelyyours, ApplicantSignature PrintedName:EdwardLiang Title:Manager Tel.:13527866242 Email:[email protected]

Page1 of 4FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. ExternalPhoto s Photo1 Photo2 Page2 of 4FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. Photo3 Photo4 Page3 of 4FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. Photo5 Photo6 Page4 of 4FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. Photo7 ------End------

Label PMN:CUBE HVIN:GANicarry4 FCCID:2BOJ7-GANIC4 IC:32086-GANIC4 Size:L10*W10mm Note:Thelabelissilk-screenonthesample

Page1 of 6FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. InternalPhoto s Photo1 Photo2 Page2 of 6FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. Photo3 Photo4 Page3 of 6FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. Photo5 Photo6 Page4 of 6FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. Photo7 Photo8 Page5 of 6FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. Photo9 Photo10 Antenna Page6 of 6FCC ID: 2BOJ7-GANIC4 DongguanYaxu (AiT) TechnologyLimited No.22,Jinqianling3rd Street,Jitigang, Huangjiang,Dongguan,Guangdong,China. Photo11 Photo12 ------End------

Page1of8ReportNo.:AiTDG-251107006W3 Note:Thisdevicehasbeentestedandfoundtocomplywiththestandard(s)listed,thistestreportmerelycorrespondstothe testsample.Itisnotpermittedtocopyextractsofthesetestresultwithoutthewrittenpermissionofthetestlaboratory.This reportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofDongguanYaxu(AiT)TechnologyLimited.Ifthere isaneedtoalterorrevisethisdocument,therightbelongstoDongguanYaxu(AiT)TechnologyLimited,anditshouldgivea priorwrittennoticeoftherevisiondocument.Thistestreportmustnotbeusedbytheclienttoclaimproductendorsement. DongguanYaxu(AiT)TechnologyLimited No.22,Jinqianling3rdStreet,Jitigang,Huangjiang,Dongguan,Guangdong,China. RFExposureevaluation ProductName: CUBE BrandName: GANCUBE Model: GANicarry4 SeriesModel: GAN3X3 FCCID: 2BOJ7-GANIC4 Applicant: GANCUBEINC. Address: Room101-901,Building2,CIMCSmartPark,No.3Chanxing Road,ShundeDistrict,Foshan,Guangdong,China Manufacturer: GANCUBEINC. Address: Room101-901,Building2,CIMCSmartPark,No.3Chanxing Road,ShundeDistrict,Foshan,Guangdong,China Standard(s): 47CFR§1.1310,47CFR§2.1093 KDB447498D01GeneralRFExposureGuidancev06 DateofReceipt: Nov.07,2025 DateofTest: Nov.07,2025~Nov.25,2025 IssuedDate: Nov.26,2025 IssuedBy: DongguanYaxu(AiT)TechnologyLimited No.22,Jinqianling3rdStreet,Jitigang,Huangjiang,Dongguan,Guangdong,China Tel.:+86-769-82020499Fax.:+86-769-82020495 Reviewedby:Approvedby: EmiyaLinSimbaHuang Page 2 of 8 ReportNo.:AiTDG-251107006W3 ReportReviseRecord ReportVersionIssuedDateNotes V1.0Nov.26,2025InitialRelease Page 3 of 8 ReportNo.:AiTDG-251107006W3 Contents 1GENERALINFORMATION.............................................................................................................................................4 1.1ENVIRONMENTALCONDITIONS........................................................................................................................................4 1.2GENERALDESCRIPTIONOFEUT......................................................................................................................................4 1.3TESTFACILITY...............................................................................................................................................................5 1.4MEASUREMENTUNCERTAINTY........................................................................................................................................6 2METHODOFMEASUREMENT......................................................................................................................................7 2.1APPLICABLESTANDARD.................................................................................................................................................7 2.2EVALUATIONMETHODANDLIMIT...................................................................................................................................7 2.3MANUFACTURINGTOLERANCE........................................................................................................................................8 2.4EVALUATIONRESULT......................................................................................................................................................8 2.5CONCLUSION................................................................................................................................................................8 Page 4 of 8 ReportNo.:AiTDG-251107006W3 1GENERALINFORMATION 1.1Environmentalconditions Duringthemeasurementtheenvironmentalconditionswerewithinthelistedranges: NormalTemperature:25°C RelativeHumidity:55% AirPressure:101kPa 1.2GeneralDescriptionofEUT ProductName:CUBE Model/Type reference: GANicarry4 SerialModel:GAN3X3 PowerSupply: Battery:DC3.0V LR43DC1.5V,100mAh*2 Hardwareversion.:V4 Softwareversion.:V1.0 Testsample(s)ID:AiTDG-251107006-1 BT: Modulation:GFSK Operationfrequency:2402MHz-2480MHz Channelnumber:40Channels Channelseparation:2MHz Antennatype:ChipAntenna Antennagain:2.28dBi Remark:TheaboveDUT'sinformationwasdeclaredbymanufacturer.Formoredetailedfeatures description,pleaserefertothemanufacturer’sspecificationsortheUser'sManual. Page 5 of 8 ReportNo.:AiTDG-251107006W3 1.3TestFacility TestLaboratory: DongguanYaxu(AiT)TechnologyLimited No.22,Jinqianling3rdStreet,Jitigang,Huangjiang,Dongguan,Guangdong,China Thetestfacilityisrecognized,certifiedoraccreditedbythefollowingorganizations: CNAS-RegistrationNo:L6177 DongguanYaxu(AiT)technologyLimitedisaccreditedtoISO/IEC17025:2017generalRequirements forthecompetenceoftestingandcalibrationlaboratories(CNAS-CL01AccreditationCriteriaforthe competenceoftestingandcalibrationlaboratories)onApril18,2022 FCC-RegistrationNo.:703111DesignationNumber:CN1313 DongguanYaxu(AiT)TechnologyLimitedhasbeenregisteredandfullydescribedinareportfiledwith the(FCC)FederalCommunicationsCommission.TheacceptanceletterfromtheFCCismaintainedin ourfiles. IC—RegistrationNo.:6819ACABidentifier:CN0122 The3mSemi-anechoicchamberofDongguanYaxu(AiT)TechnologyLimitedhasbeenregisteredby CertificationandEngineeringBureauofIndustryCanadaforradioequipmenttestingwithRegistration No.:6819A A2LA-LabCert.No.:6317.01 DongguanYaxu(AiT)TechnologyLimitedhasbeenaccreditedbyA2LAfortechnicalcompetencein thefieldofelectricaltesting,andprovedtobeincompliancewithISO/IEC17025:2017General RequirementsfortheCompetenceofTestingandCalibrationLaboratoriesandanyadditionalprogram requirementsintheidentifiedfieldoftesting. Page 6 of 8 ReportNo.:AiTDG-251107006W3 1.4Measurementuncertainty Thedataandresultsreferencedinthisdocumentaretrueandaccurate.Thereaderiscautionedthat theremaybeerrorswithinthecalibrationlimitsoftheequipmentandfacilities.Themeasurement uncertaintywascalculatedforallmeasurementslistedinthistestreportaccordingtoCISPR16- 4“Specificationforradiodisturbanceandimmunitymeasuringapparatusandmethods–Part4: UncertaintyinEMCMeasurements”andisdocumentedintheDongguanYaxu(AiT)Technology Limited’squalitysystemaccordingtoDINENISO/IEC17025.Furthermore,componentandproce…

Text truncated - open the document above for the full version.

Page1of33ReportNo.:AiTDG-251107006W2 DongguanYaxu(AiT)TechnologyLimited No.22,Jinqianling3rdStreet,Jitigang, Huangjiang,Dongguan,Guangdong,China. TESTREPORT ClientInformation: Applicant:GANCUBEINC. Applicantadd.: Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,Shunde District,Foshan,Guangdong,China Manufacturer:GANCUBEINC. Manufactureradd.: Room101-901,Building2,CIMCSmartPark,No.3ChanxingRoad,Shunde District,Foshan,Guangdong,China ProductInformation: ProductName:CUBE ModelNo:GANicarry4,GAN3X3 BrandName:GANCUBE FCCID:2BOJ7-GANIC4 Applicablestandards: FCCCFRTitle47Part15SubpartCSection15.247 PreparedBy: DongguanYaxu(AiT)TechnologyLimited No.22,Jinqianling3rdStreet,Jitigang,Huangjiang,Dongguan, Guangdong,China Tel.:+86-769-82020499Fax.:+86-769-82020495 DateofReceipt:Nov.07,2025DateofTest:Nov.07,2025~Nov.25,2025 DateofIssue:Nov.26,2025TestResult:Pass ThisdevicedescribedabovehasbeentestedbyDongguanYaxu(AiT)TechnologyLimitedandthe testresultsshowthattheequipmentundertest(EUT)isincompliancewiththeFCCrequirements. Anditisapplicableonlytothetestedsampleidentifiedinthereport. Note:Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofDongguan Yaxu(AiT)TechnologyLimited,thisdocumentmaybealteredorrevisedbyDongguanYaxu(AiT) TechnologyLimited,personalonly,andshallbenotedintherevisionofthedocument.Thistest reportmustnotbeusedbytheclienttoclaimproductendorsement. Reviewedby:Approvedby: EmiyaLinSimbaHuang Page2of33ReportNo.:AiTDG-251107006W2 DongguanYaxu(AiT)TechnologyLimited No.22,Jinqianling3rdStreet,Jitigang, Huangjiang,Dongguan,Guangdong,China. 1Contents Page COVERPAGE 1CONTENTS...........................................................................................................................................................................2 2TESTSUMMARY.................................................................................................................................................................4 2.1StatementoftheMeasurementUncertainty.....................................................................................4 2.2MeasurementUncertainty.................................................................................................................4 3TESTFACILITY...................................................................................................................................................................5 3.1Deviationfromstandard....................................................................................................................5 3.2Abnormalitiesfromstandardconditions...........................................................................................5 3.3TestLocation.....................................................................................................................................5 4GENERALINFORMATION................................................................................................................................................6 4.1Testfrequencies................................................................................................................................7 4.2EUTPeripheralList...........................................................................................................................7 4.3TestPeripheralList............................................................................................................................7 4.4TESTMETHODOLOGY....................................................................................................................8 4.4.1EUTConfiguration.......................................................................................................................8 4.4.2EUTExercise...............................................................................................................................8 4.4.3GeneralTestProcedures.............................................................................................................8 4.5DescriptionofTestModes.................................................................................................................9 5EQUIPMENTUSEDDURINGTEST...............................................................................................................................10 6TESTRESULTSANDMEASUREMENTDATA..........................................................................................................12 6.1Antennarequirement.......................................................................................................................12 6.2OnTimeandDutyCycle.................................................................................................................13 6.3MaximumConductedOutputPowerMeasurement.......................................................................14 6.46dBSpectrumBandwidthMeasurement.......................................................................................15 6.5PowerSpectralDensity...................................................................................................................16 6.6ConductedSpuriousEmissionsandBandEdgesTest..................................................................17 6.7Restrict-bandBand-edgeMeasurements.......................................................................................18 6.8RadiatedEmissionsMeasurement.................................................................................................21 6.9ConductedEmissions.....................................................................................................................32 7TESTSETUPPHOTOGRAPHSOFEUT......................................................................................................................33 8EXTERNALPHOTOGRAPHSOFEUT.........................................................................................................................33 9INTERNALPHOTOGRAPHSOFEUT................................................................................…

Text truncated - open the document above for the full version.

SPECIFICATION FOR APPROVAL CUSTOMER ： CUSTOMER’S P/N ： PART NUMBER ： WAN1608H245H08 DESCRIPTION ： Chip Antenna 1608 MH-Ant 2.45G Type H08 VERSION ： V1.4 ISSUE DATE ： 2025/09/30 CUSTOMER APPROVED R&D CENTER APPROVAL CHECKED DRAWN Ray Tennyson Snow OneWave Electronic Co., Ltd. 1F, No. 151, Li Gong Street, Beitou District, Taipei City 11261, Taiwan TEL:+886 2 2898-2220 FAX:+886 2 2898-5055 ONEWAVE TECHNOLOGY CO., LTD. 2/13 1608 Chip antenna For Bluetooth / WLAN Applications Dimension (mm) L 1.70 ± 0.20 W 0.93 ± 0.20 T 0.75 ± 0.20 P/N: WAN1608H245H08 ONEWAVE TECHNOLOGY CO., LTD. 3/13 Part Number Information WAN 1608 H 245 H 08 A B C D E F A Product Series Antenna B Dimension L x W 1.6X0.8mm (+-0.2mm) C Material High K material D Working Frequency 2.4 ~ 2.5GHz E Feeding mode Monopole & Single Feeding F Antenna type Type = 08 1. Electrical Specification Remark : Bandwidth & Peak Gain was measured under evaluation board of next page Specification Part Number WAN1608H245H08 Central Frequency 2450 MHz Bandwidth 120 (Min.) MHz Return Loss -10(Max) dB Peak Gain 2.28 dBi Impedance 50 Ohm Operating Temperature -40～+110 °C Maximum Power 4 W Resistance to Soldering Heats 10 ( @ 260°C) sec. Polarization Linear Azimuth Beamwidth Omni-directional Termination Cu / Sn (Leadless) ONEWAVE TECHNOLOGY CO., LTD. 4/13 2. Recommended PCB Pattern 1. Evaluation Board Dimension Unit : mm 2. Evaluation Board Dimension 3. Evaluation Board Dimension ONEWAVE TECHNOLOGY CO., LTD. 5/13 Suggested Matching Circuit Important information: It is recommended to use highly accurate inductors ±0.1~0.3nH and capacitance ±0.1pF for matching components. 1. Layout Dimensions in Clearance area(Size=5.5*4mm) 50 ohm transmission Line Matching Circuit 2. Layout Dimensions in Clearance area(Size=5.5*4mm) 50 ohm transmission Line Matching Circuit 1～10nH None 0Ω 1.5pF ONEWAVE TECHNOLOGY CO., LTD. 6/13 3. Layout Dimensions in Clearance area(Size=5*3mm) 50 ohm transmission Line Matching Circuit FootPrint (Unit : mm) ONEWAVE TECHNOLOGY CO., LTD. 7/13 3. Measurement Results Return Loss ONEWAVE TECHNOLOGY CO., LTD. 8/13 3D Radiation Pattern 2D Radiation Pattern @2400MHz @2450MHz @2500MHz Z Y X ONEWAVE TECHNOLOGY CO., LTD. 9/13 Efficiency Peak Gain Directivity 2400MHz 50.65 % 1.80 dBi 3.95 dBi 2450MHz 53.27 % 2.28 dBi 4.42 dBi 2500MHz 50.32 % 1.77 dBi 4.15 dBi Chamber Coordinate System ONEWAVE TECHNOLOGY CO., LTD. 10/13 4.Reliability and Test Condictions ITEM REQUIREMENTS TEST CONDITION Solderability 1. Wetting shall exceed 90% coverage 2. No visible mechanical damage Pre-heating temperature:150°C/60sec. Solder temperature:230±5°C Duration:4±1sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Solder heat Resistance 1. No visible mechanical damage 2. Central Freq. change :within ± 6% 10±0.5 sec. 60sec .. TEMP (°C) 150°C 260°C Pre-heating temperature:150°C/60sec. Solder temperature:260±5°C Duration:10±0.5sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Component Adhesion (Push test) 1. No visible mechanical damage The device should be reflow soldered(230±5°C for 10sec.) to a tinned copper substrate A dynometer force gauge should be applied the side of the component. The device must with-ST-F 0.5 Kg without failure of the termination attached to component. Component Adhesion (Pull test) 1. No visible mechanical damage Insert 10cm wire into the remaining open eye bend ,the ends of even wire lengths upward and wind together. Terminal shall not be remarkably damaged. Thermal shock 1. No visible mechanical damage 2. Central Freq. change :within ±6% Phase Temperature(°C) Time(min) 1 +110±5°C 30±3 2 Room Temperature Within 3sec 3 -40±2°C 30±3 4 Room Temperature Within 3sec +110°C=>30±3min -40°C=>30±3min Test cycle:10 cycles The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance to High Temperature 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature: +110±5°C Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance to Low Temperature 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature:-40±5°C Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Humidity 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature: 40±2°C Humidity: 90% to 95% RH Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. 4±1 sec. 60sec TEMP (°C) 150°C 230°C ONEWAVE TECHNOLOGY CO., LTD. 11/13 5.Soldering and Mounting Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. The terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Recommended temperature profiles for re-flow soldering in Figure 1. Products attachment with a soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. ‧Preheat circuit and products to 150°C ‧Never contact the ceramic with the iron tip ‧Use a 20 watt soldering iron with tip diameter of 1.0mm ‧280°C tip temperature (max) ‧1.0mm tip diameter (max) ‧Limit soldering time to 3 sec. SOLDERING COOLING NATURAL PRE-HEATING TEMPERATURE(°C) 60~120 s 10s max. 30~60s 250~260 230 180 150 TIME(sec.) Reflow Soldering SOLDERING COOLING NATURAL PRE-HEATING TEMPERATURE(°C) within 3s Gradualcooling 150 TIME(sec.) Iron Soldering Over 60s 350 300 ONEWAVE TECHNOLOGY CO., LTD. 12/13 6.Packaging Information ◆ Tape Specification: W Ao Bo Ko P F E D D1 Po P2 t 8.0 ±0.30 1.10± 0.05 1.90 ±0.10 1.10± 0.10 4.00 ±0.05 3.50 ±0.05 1.7…

Text truncated - open the document above for the full version.

DongguanYaxu(AiT)TechnologyLimited ReportNo.: AiTDG-251107006W2 FCC ID : 2BOJ7-GANIC4 Page 1 of 24 AppendixB RF Test Data for BT (BLE)(ConductedMeasurement) ProductName:CUBE TradeMark:GANCUBE Test Model:GAN i carry 4 EnvironmentalConditions Temperature: 24.6  C R…

Text truncated - open the document above for the full version.