2BQNA-U8-390Cutting plotter (Film cutting machine)

WiFi 2.4G&5G 7-inch Touchscreen 0.1mm 500mm/s 1500g <50w DC24V 2.75A Stepper Motor 5°C~35°C 35%-70% U8-310U8-390 Model Number Max Material Size Max Cutting Screen Size Connection Display Cutting Accuracy Max Cutting Speed Max Cutting Pressure Power Rating Input Voltage Drive System Operating Temperature Operating Humidity Machine Dimensions Net Weight Main Unit *1 Automatic tool holder*1 Cutting blade*1 Adapter*1 Power Cord*1 ①Connect the power cord to the adapter, plug one end of the power cord into a power socket, plug one end of the adapter cable into the power interface of the film cutting machine and lock it, then install the cutter head into the tool holder slot next to the driver, ensuring it is fixed. ②After connection, press the [Power Button] to start the device. Product ListUser Instructions Machine Settings Precautions Product parameters Appearance and Functions U8 Film cutting machine Instruction Manual ①Carriage ②Electric blade Holder ③blade Holder Clip: to fix the electric blade holder ④Touch Screen ⑤Power Button: to start the machine ⑥Pressure Roller: Holds film in position during cutting ⑦Film Feed Sensor: Auto-detects film insertion ⑧Power Input Port: For power adapter connection Network Port USB-A Port (Power Supply Only) USB-C Port (Power Supply Only) USB Port: Insert this connector into the vehicle-mounted cutter interface during installation Blade Needle Slider: when replacing the blade needle, gently push the slider to extend the blade needle and take out the blade needle to be replaced Tool holder base: Rotate the tool holder clamping bolt to lock the tool Blade tip: Adjust the exposed length according to the thickness of the material Upper and lower fixtures Left and right fixtures Power interface Clamp/Release Button 9 10 11 12 13 14 15 16 17 18 19 12 13 14 15 1.Power Connection and Startup 1.Language Settings 2.WiFi Settings On the homepage, select the mobile phone brand/model/film type you need to cut, and click 【Scan Code to Cut】 Note: After replacing the blade needle or blade holder, please perform blade needle calibration; otherwise, abnormal cutting may occur. For specific operations, refer to - Machine Settings - 【blade Depth Calibration】. 4.Starting Cutting After the film cutting machine finishes cutting, the protective film will be ejected. 5.Cutting Completed 6.Starting Film Application 2. Install the Cutter Blade Holder ①Prepare the electric blade holder and loosen the blade holder clip counterclockwise； ②Place the electric blade holder vertically into the blade holder clip and insert it into the tool interface of the carriage； ③Tighten the blade holder clip clockwise to complete the blade holder installation. ①Before starting film application, connect the film cutting machine and the film application fixture with a Type-C power cord, and long press the 【Clamp/Release】 button on the film application fixture to keep the clamp in the released state； ②Place the mobile phone horizontally on the film application fixture with the screen facing up, and tap the 【Clamp/Release】button on the film application fixture to fix the mobile phone; Note: The mobile phone camera should face the "Top" direction of the clamp; ③Clean the mobile phone screen with alcohol and a lint-free cloth; ④ Separate the cut film sheet from the base plate, and use a squeegee to fix the 4 cut positioning holes on the film sheet to the 4 positioning posts of the film application fixture; ⑤Use a squeegee to make the film sheet closely adhere to the mobile phone screen, and peel off the waste material. 7.Film Application Completed Tap the 【Clamp/Release】 button on the film application fixture to take out the mobile phone, and the film application is completed. 3.Placing Materials ①Prepare a protective film to be cut, and confirm that the protective film is flat, the film layer is complete, and there is no bending, folding or delamination; ②Place the film sheet in the indicated area； ③The machine will automatically sense and take in the film paper； ④If you need to replace with other film paper, press the power button once to eject the film paper. Top Bo ttom On the homepage, click the【 Settings Button】to enter the settings interface, then click [Language Settings] to switch. On the homepage, click【 Settings Button】, enter the settings interface, click 【WiFi Settings】to connect to WiFi and enter the password, then wait for the machine to successfully connect to the WiFi network. Click【 Settings Button】on the homepage, enter the settings interface, select【Parameter Settings】, and adjust according to actual usage. ①On the homepage, click【 Settings Button】, enter the settings interface, select【Parameter Settings】, scroll down to find the【Knife Depth Calibration】option, and click【Calibrate】. ②Please follow the "Placing Materials" steps in the "User Instructions" to place a protective film to be cut. ③According to the text instructions on the touch screen, click【Start Cutting Calibration】, and the machine will automatically cut 40 line segments with different knife depth levels on the film sheet. ④After the cutting is completed, find the last line segment with visible cutting marks on the film sheet, select the corresponding line segment number and click 【Calibrate】to complete the knife depth calibration. 4.Knife Depth Calibration 5.Self-service Value-added Times 16 17 18 19 300mm 200mm 410mm 295mm 410*220*202mm 6.8kg 510*220*202mm 8.5kg T op Bo t t om T op Bo t t om ⑥ ⑤ 6.APP Upgrade/Data Update ①On the homepage, click【 Settings Button】, enter the settings interface, click【System Information】, then click【Version Update】, enter the update password: 1313, and wait for the APP to update successfully. For the placement position of the film sheet, refer to the dotted line guide. The cutting tool is sharp; do not put your hands into the cutting area to avoid cuts. Note: The small positioning hole at the top is fixed on the small positioning post at the "Top" end, and the large positioning hole at the t…

Text truncated - open the document above for the full version.

3/20 Fed Auth 7435 Colu USA AT T FCC Skyc auth equi Sky c the a nam equi Sky c auth prov equi cybe Cov Sig n Prin Titl e Com Date Co 0/2026 eral Comm u horization a 5 Oakland M umbia, MD 2 A TN.: Review C ID: 2BQNA cut Technol horization is ipment auth Note: If any of t h include cut Technol application, med entity or ipment. cut Technol horization is vided by Ka ipment with ersecurity o vered Equipm ned: ted name: J e: CEO mpany Name e: 3/20/2026 overed Eq unications C nd Evaluatio Mills Road 21046 wing Engin A-U8-390 logy Co., Lt sought is n horization pu the equipm he entities id an explanat logy Co., Lt the applic a r any of its s logy Co., Lt sought do e aspersky La integrated r anti-virus ment Guida Jianglin Li e: Skycut T 6 Skycut quipment Commission on Division neer d. (“the app not “covered ursuant to s ent for whic dentified on tion on why d. (“the app ant is not ide subsidiaries d. (“the app es not includ ab, Inc. or an Kaspersky software pu ance section echnology C Technology t Certifica n plicant”) cert d” equipmen section 2.90 ch the applic n the current y the equipm plicant”) cert entified on t s or affiliates plicant”) cert de cybersec ny of its suc y Lab, Inc. (o ursuant to D n B(2a). Co., Ltd. y Co., Ltd. ation Attes tifies that th nt prohibited 3 of the FC cant seeks a t Covered L ment is not “ tifies that, a he Covere d s) as an ent tifies that th curity or ant ccessors an or any of its DA-24-886 a station Le e equipmen d from receiv C rules. authorizatio List, the app covered” eq s of the dat d List (as a s ity producin e equipmen ti-virus softw d assignees successors and KDB 98 etter nt for which ving an on is produc plicant shoul quipment. e of the fili n specifically ng “covered” nt for which ware produc s, including s and assign 6446 D01 ced by ld ng of ” h ced or nees)

Marc Fede Auth 7345 Colu On o Bloc Distr agen subm certif defin labe For i beha for c Build Distr <Sig n Name Title： Applic ch 20, 2026 eral Commu horization & 5 Oakland M umbia, Mary our behalf, ck B, Jun Xi rict, Shenzh nt in the p mitted docu fication is so ned in the F l identical to instances w alf, I acknow certification, ding A, No. 2 rict, Shenzhe nature>： e：Jianglin CEO cant Compa 6 unications C Evaluation D Mills Road land 21046 I appoint S ang Da Bui hen, China. preparation uments prop ought. I also Federal Com o that submit where our au wledge that still resides 235, Qingsh en, China Li any：Skycu ommission Division Author i Shenzhen T lding, Zhong (Name of A of this app perly descr o certify that mmunications tted for appr uthorized ag all responsi with S k y c hui Road, Wu ut Technolog ity to Act as Timeway Te gshan Park Agent comp plication for ribe the de t each unit m s Commissi roval with th ent signs th ibility for com cut Techn ulian Comm gy Co., Ltd. s Agent esting Labor Road West pany name r equipment evice or sy manufacture ion’s regulat his applicatio he applicatio mplying with ology Co munity, Longg . ratories/ Zon t, Tong Le V and addres t certificatio stem for w ed, imported tions will ha on. on for certific h the terms ., Ltd. / F gang Street ne C, 1st F Village, Nan ss) to act a on. I certify which equip d or markete ave affixed t cation on ou and conditio Floors 101-6 , Longgang Floor, nshan s our y that pment ed, as to it a ur ons 01,

March 20, 2026 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BQNA-U8-390 Product Name: Cutting plotter (Film cutting machine) Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>： Name：Jianglin Li Title： CEO Applicant Company：Skycut Technology Co., Ltd.

Skycut Technology Co., Ltd. Statement We Skycut Technology Co., Ltd. Hereby Declare that The product Cutting plotter (Film cutting machine), models no. U8-390, U8-310, H2, H2-310, H2-390, U5, U6, U7, U8, U9, U10, U11, U12, U13 are all identical in interior structure, electrical circuits and components, and just the model names are different for the marketing requirement. Your assistance on this matter is highly appreciated. Yours sincerely, Signature: Company Name: Skycut Technology Co., Ltd.

FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390

Cutting plotter(Film cutting machine) Model：U8-390 Input：24VDC 2.7A FCC ID: 2BQNA-U8-390 Skycut Technology Co., Ltd. Made in China This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Label Location

FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 FCC ID: 2BQNA-U8-390 Antenna

Maximum Permissible Exposure FCC ID: 2BQNA-U8-390 Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2m normally can be maintained between the user and the device. (a) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times ︱E︱ 2 , ︱H︱ 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100000 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times ︱E︱ 2 , ︱H︱ 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100000 1.0 30 Note: f=frequency in MHz; *Plane-wave equivalent power density MPE Calculation Method E (V/m) = (30*P*G) 0.5 /d Power Density: Pd (W/m 2 ) = E 2 /377 E = Electric Field (V/m) P = Peak RF output Power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = (30*P*G) / (377*d 2 ) From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Calculated Result and Limit Mode-BLE Antenna Gain: -0.10dBi Assembly Antenna Gain: 0.977 Assembly Antenna Gain (Numeric) Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 0.977 -0.42 0.908 0.00018 1 Compiles Mode-WIFI 2.4G Band Antenna Gain: 2.57dBi Assembly Antenna Gain: 1.81 Assembly Antenna Gain (Numeric) Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 1.81 12.57 18.07 0.00651 1 Compiles Mode-BT Antenna Gain: -0.10dBi Assembly Antenna Gain: 0.977 Assembly Antenna Gain (Numeric) Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 0.977 -1.29 0.743 0.00014 1 Compiles Mode-WIFI 5G Band 1 Antenna Gain: 2.87dBi Assembly Antenna Gain: 1.94 Assembly Antenna Gain (Numeric) Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 1.94 12.81 19.10 0.00737 1 Compiles Mode-WIFI 5G Band 2 Antenna Gain: 2.87dBi Assembly Antenna Gain: 1.94 Assembly Antenna Gain (Numeric) Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 1.94 11.6 14.45 0.00558 1 Compiles Mode-WIFI 5G Band 4 Antenna Gain: 2.87dBi Assembly Antenna Gain: 1.94 Assembly Antenna Gain (Numeric) Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 1.94 12.43 17.49 0.00675 1 Compiles

Report No.: TW2601014-02E Applicant: Skycut Technology Co., Ltd. Product: Cutting plotter (Film cutting machine) Model No.: U8-390, U8-310, H2, H2-310, H2-390, U5, U6, U7, U8, U9, U10, U11, U12, U13 Trademark: N/A Test Standards: FCC Part 15.247 Test Result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10, FCC Part 15.247 for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: March 13, 2026 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No.: TW2601014-02E Page 2 of 44 Date: 2026-03-13 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. ISED —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of ISED for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 CAB identifier: CN0033 FCC Designation Number: CN1251 Report No.: TW2601014-02E Page 3 of 44 Date: 2026-03-13 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT ........................................................................................... 4 1.4 Submitted Sample.............................................................................................. 4 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty............................................................................................... 5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification.............................................................................................7 5.0 Power Line Conducted Emission Test...................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating Condition....................................................................................9 5.5 Conducted Emission Limit................................................................................... 9 5.6 Test Result...................................................................................................... 9 6.0 Radiated Emission test...................................................................................... 12 6.1 Test Method and Test Procedure...................................................................…

Text truncated - open the document above for the full version.

Report No.: TW2601014-03E Applicant: Skycut Technology Co., Ltd. Product: Cutting plotter (Film cutting machine) Model No.: U8-390, U8-310, H2, H2-310, H2-390, U5, U6, U7, U8, U9, U10, U11, U12, U13 Trademark: N/A Test Standards: FCC Part 15.247 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10, FCC Part 15.247 for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: March 13, 2026 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No.: TW2601014-03E Page 2 of 87 Date: 2026-03-13 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. ISED —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of ISED for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 CAB identifier: CN0033 FCC Designation Number: CN1251 Report No.: TW2601014-03E Page 3 of 87 Date: 2026-03-13 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details............................................................................................... 4 1.3 Description of EUT ........................................................................................... 4 1.4 Submitted Sample.............................................................................................. 5 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty............................................................................................... 5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 8 3.1 Summary of Test Results..................................................................................... 8 3.2 Test Standards.................................................................................................. 8 4.0 EUT Modification.............................................................................................8 5.0 Power Line Conducted Emission Test...................................................................... 9 5.1 Schematics of the Test........................................................................................ 9 5.2 Test Method and Test Procedure............................................................................ 9 5.3 Configuration of the EUT.................................................................................... 9 5.4 EUT Operating Condition....................................................................................10 5.5 Conducted Emission Limit................................................................................... 10 5.6 Test Result..................................................................................................... 10 6.0 Radiated Emission test...................................................................................... 13 6.1 Test Method and Test Procedure................................................................…

Text truncated - open the document above for the full version.

DX-BT18AntennaSpecification ContactUs ShenzhenDX-SMARTTechnologyCo.,Ltd. Email：[email protected] Tel：0755-29978125 Web：www.szdx-smart.com Add：Room601,BlockA1,HuafengZhigu,HangkongRoad,BaoanDistrict,Shenzhen DX-BT18AntennaSpecification ShenzhenDX-SMARTTechnologyCo.,Ltd.www.szdx-smart.com -1- 1.AntennaSizeDiagram 2.AntennaEfficiencyAndGain DX-BT18AntennaSpecification ShenzhenDX-SMARTTechnologyCo.,Ltd.www.szdx-smart.com -2-

深圳市亿圣邦科技有限公司第 1 页 深圳市亿圣邦科技有限公司 样品承认书 SPECIFICATIONFORAPPROVAL 公司名称（客户填写）：深圳亿东科技股份有限公司 物料代码（客户填写）： 规格型号（客户填写）：EMR327S 承认日期（客户填写）： 供应商名称（SLK填写）：深圳市亿圣邦科技有限公司 供应商型号（SLK填写）：WIFI:SLK-YD-2416A-L-50I-B-1.13 承认签章 供应商承认深圳亿东科技股份有限公司 工程师审核批准工程师审核批准 范新竹黄震林美财 盖章签署盖章签署 日期2025-07-05日期 批示：□接受□有条件接受 备注（客户填写）： 供应商名称:深圳市亿圣邦科技有限公司 供应商地址:深圳市宝安区西乡街道南昌社区前湾硬科技产业园C栋101 电话：18666299104传真：0769-82553116 深圳市亿圣邦科技有限公司第 2 页 WIFI 1.ExplanationofProductnumber: ProductCode: (1)Customer: 亿冬 (2)AntennaName:WIFI天线（WIFIAntenna） (3)Connector:1.13 黑色线，总长 50mm ， 1 代端子 2.Features *Stableandreliableinperformances *Compactsize *RoHScompliance 3.Applications *IEEE802.11(b/g/n/a) *Hand-helddeviceswhenWIFI(802.11b/g/n/a)functionsareneeded 4.Description Holybond’sFPCantennaseriesarespeciallydesignedforWIFI (802.11b/g/n/a)applications.BasedonHolybond’sproprietarydesignand processes,thisFPCantennahasexcellentstabilityandsensitivityto consistentlyprovidehighsignalreceptionefficiency. 深圳市亿圣邦科技有限公司第 3 页 5.ElectricalSpecifications 5-1 CharacteristicsSpecificationsUnit OutlineDimensions24.77x16.3x0.32mm CenterFrequency 2.4-2.5+5.15-5.85GHz Bandwidth(under-10dBreturnloss) 130minMHz VSWR 3max 5-2． VSWRS11 深圳市亿圣邦科技有限公司第 4 页 5-3.WIFI+BTAntennaGain/Efficiency/RadiationPatternof3D 深圳市亿圣邦科技有限公司第 5 页 6.AntennaDimensions(unit:mm) 深圳市亿圣邦科技有限公司第 6 页 7.AntennaPicture

FCC ID: 2BQNA-U8-390 Conducted Emission Test Setup: FCC ID: 2BQNA-U8-390 Radiated Emission Test Setup: FCC ID: 2BQNA-U8-390 RF test Setup: