2BSUV-08-00024-01Wireless charging pad for firearm

Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 02-13-2026 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID or Grantee Code: 2BSUV-08-00024-01 Lodestar Technology Inc (“the applicant”) certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information: FRN: 0037298353 Name: Ginger Chandler Address: 481 West 45 th Street, Suite 100, Chattanooga, TN 38410, USA Contact Person: Ginger Chandler Tel.: (860) 214-5280 Email: [email protected] Sincerely, Virginia Chandler CTO and Cofounder

Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 10/18/2025 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BSUV-08-00024-01 Lodestar Technology Inc (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Lodestar Technology Inc (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 98 6446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, Virginia Chandler Rev 1/26/2023 , Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 10/18/2025 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BSUV-08-00024-01 Lodestar Technology Inc (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely Virginia Chandler

Date: (19/02/2026) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Dear Sir or Madam, We, Lodestar Technology Inc (“the applicant”), hereby authorize Hoosamuddin Bandukwala of H.B. Compliance Solutions, 5005 S. Ash Avenue, Suite A-10, Tempe AZ-85282 and Jesse Snyder of 28Gorilla to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. Yours sincerely, Name: Virginia Chandler Title: Co-Founder and CTO

Date 1/28/2026 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request FCC ID: 2BSUV-08-00024-01 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, Lodestar Technology Inc. hereby requests permanent confidential treatment of information accompanying this application as outlined below: Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation Lodestar Technology Inc hereby requests short-term confidential treatment of information accompanying this application as outlined below for a period of period of 60 days: Internal Photos External Photos User Manual Test Set-up Photographs The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Name: Title: Virginia Chandler CTO and Co-founder

Certificates and reports shall not be reproduced except in full, without the written permission of H.B Compliance Solutions, LLC. RF Exposure Evaluation Report For the Lodestar Technology, Inc. LNK Charging Pad 13 October 2025 Prepared for: Lodestar Technology, Inc. 481 W 45th St Chattanooga, TN 37410 Prepared By: H.B. Compliance Solutions 5005 S. Ash Avenue, Suite # A-10 Tempe, Arizona 85282 Reviewed By: Hoosamuddin Bandukwala Cert # ATL-0062-E HBCS RF Exposure Report # EMC_25042_2 Page 2 of 10 1. Equipment Overview Product Name: LNK Charging Pad Model(s) Tested: N/A FCC ID: 2BSUV-08-00024-01 Supply Voltage Input: Primary Power: 120 VAC Frequency Range: 0.191 kHz No. of Channels: 1 Type(s) of Modulation: Sinewave Range of Operation Power: 0.009 mW (Radiated) Emission Designator: N/A Channel Spacing(s) None Test Item: Pre-Production Type of Equipment: Fixed Measurement Distance declared by manufacturer 20 cm Antenna Requirement (§15.203): Type of Antenna: Integral Loop Gain of Antenna: 0dBi Environmental Test Conditions: Temperature: 15-35⁰C Humidity: 30-60% Barometric Pressure: 860-1060 mbar Modification to the EUT: None Evaluated By: Staff at H.B Compliance Solutions Test Date(s): October 06-07, 2025 HBCS RF Exposure Report # EMC_25042_2 Page 3 of 10 2. Applicable Standard According to §1.1307 the criteria listed in table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of §2.1093 of this chapter. RF exposure is calculated according to KDB680106 D01v04: Wireless Power Transfer. 3. Test Limits Evaluated against exposure limits: General Use _X_ or Controlled Use ___ Maximum Permissible Exposure (MPE) f = frequency in MHz* = Plane-wave equivalent power density RF exposure compliance will need to be determined with respect to 1.1307(c) and (d) of the FCC rules. The emissions should be within the limits at 300kHz in the above table. (Use 300kHz limits for 150kHz) HBCS RF Exposure Report # EMC_25042_2 Page 4 of 10 4. RF Exposure Requirements This device and the test results is in compliance with item 5.2 of FCC KDB 680106 D01v04 below and can be excluded from submitting an RF exposure evaluation 1. Power transfer frequency is less than 1MHz 2. Output power from each primary coil is less than or equal to 15 watts 3. Client device is placed directly in contact with the transmitter 4. Mobile exposure conditions only (portable exposure conditions are not covered by the exclusion) 5. The aggregate H-field strengths at 20cm surrounding the device from all simultaneous coils are demonstrated to be less than 50% of the MPE Limit. 6. The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. HBCS RF Exposure Report # EMC_25042_2 Page 5 of 10 5. Test Limits Evaluated against exposure limits: General Use _X_ or Controlled Use ___ Maximum Permissible Exposure (MPE) f = frequency in MHz* = Plane-wave equivalent power density RF exposure compliance will need to be determined with respect to 1.1307(c) and (d) of the FCC rules. The emissions should be within the limits at 300kHz in the above table. (Use 300kHz limits for 150kHz) HBCS RF Exposure Report # EMC_25042_2 Page 6 of 10 6. Measurement Procedure Test Setup 1. The RF exposure test was performed in a Shield Room 2. For RF exposure purposes, the E and H field strengths were measured separately with E and H field probes. 3. EUT was placed on a turntable and the measurement probe was placed at the manufacturer’s specified distance d from the center of the probe to the edge of the device. 4. The measurement probe used to search for the highest strength 5. The highest emission level was recorded and compared with the limit for each point (A, B, C, D & E) 6. The EUT were measured according to the KDB 680106d01v04. HBCS RF Exposure Report # EMC_25042_2 Page 7 of 10 7. Test Results Frequency Range (MHz) Probe Position A (A/m) Probe Position B (A/m) Probe Position C (A/m) Probe Position D (A/m) Probe Position E (A/m) FCC Limits (A/m) Mode 0.191 0.012 0.030 0.015 0.006 0.059 1.63 Idle 0.191 0.017 0.032 0.016 0.007 0.052 1.63 Resistive Load H-Field Strength from the edges surrounding the EUT Frequency Range (MHz) Probe Position A (V/m) Probe Position B (V/m) Probe Position C (V/m) Probe Position D (V/m) Probe Position E (V/m) FCC Limits (V/m) Mode 0.191 0.988 1.178 1.42 1.272 1.784 614 Idle 0.191 0.992 1.288 1.361 1.242 2.007 614 Resistive Load E-Field Strength from the edges surrounding the EUT Note: The worst-case data were reported. The field strength limit refers to Part 1.1310 and the test results of exposure is compliant. 50% of the MPE limit (E-Field: 307 V/m; H-field: 0.815A/m) Device meets the RF Exposure limits based on the above measurement. HBCS RF Exposure Report # EMC_25042_2 Page 8 of 10 Simultaneous Transmission Evaluation Limit The sum of the ratios of the peak or spatially averaged results to the applicable frequency dependent MPE limits must be <1 at all locations where users and bystanders can by exposed. Calculation Mode WPT Power Density/Limit Bluetooth Power Density/Limit WiFi Power Density /Limit Cellular Power Density/ Limit ∑(Power Density/Limit) of WiFi+191kHz +Cellular Transmitter ∑(Power Density/Limit) of Bluetooth+191kHz +Cellular Transmitter WiFi 0.0732 0.1342 Bluetooth 0.0489 0.1099 Cellular 0.06 191kHz 0.001 The 191kHz, WiFi , Bluetooth and cellular transmitter, the aggregated (power density/limit) is smaller than 1, and the MPE of 3 collocated transmitters is compliant. Note: FCC ID for the pre-certified Wifi, Bluetooth, and Cellular modules are: WIFI - 2ADHKWIXCS02 BLE - 2ADHKWBZ451 Cellular - 2AAGMGM025A BT antenna and Wi-Fi 2.4G Antenna can’t transmit simultaneously. HBCS RF Exposur…

Text truncated - open the document above for the full version.

Certificates and reports shall not be reproduced except in full, without the written permission of H.B Compliance Solutions, LLC. Intentional Radiator Test Report For the Lodestar Technology, Inc. LNK Charging Pad Tested under The FCC Rules contained in Title 47 of the CFR, Part 15.209 13 October 2025 Prepared for: Lodestar Technology, Inc. 481 W 45th St Chattanooga, TN 38410 Prepared By: H.B. Compliance Solutions 5005 S. Ash Avenue, Suite # A-10 Tempe, Arizona 85282 Reviewed By: Hoosamuddin Bandukwala Cert # ATL-0062-E Engineering Statement: The measurements shown in this report were made in accordance with the procedure indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurement made, the equipment tested is capable of operation in accordance with the requirements of Part 15 of the FCC Rules under normal use and maintenance. All results contained herein relate only to the sample tested. HBCS Report # EMC_25042_2 Rev1 Page 2 of 24 Report Status Sheet Revision # Report Date Reason for Revision Ø October 13, 2025 Initial Issue 1 February 5, 2026 Corrected FCC ID for BLE HBCS Report # EMC_25042_2 Rev1 Page 3 of 24 Table of Contents EXECUTIVE SUMMARY ............................................................................................ 4 1. Testing Summary ....................................................................................... 4 EQUIPMENT CONFIGURATION ................................................................................ 5 1. Overview ................................................................................................... 5 2. Test Facility ............................................................................................... 6 3. Description of Test Sample ........................................................................ 7 4. Equipment Configuration .......................................................................... 7 5. Support Equipment ................................................................................... 7 6. Ports and Cabling Information ................................................................... 7 7. Method of Monitoring EUT Operation ...................................................... 8 8. Mode of Operation .................................................................................... 8 9. Modifications ............................................................................................ 8 10. Disposition of EUT ..................................................................................... 8 Criteria for Intentional Radiators ............................................................................ 9 1. Radiated Emissions .................................................................................... 9 Emissions Tests Calculations ...................................................................... 10 2. Conducted Emissions ............................................................................... 14 2. Occupied Bandwidth ............................................................................... 18 5. Radiated Spurious Emissions ................................................................... 20 Test Equipment ..................................................................................................... 23 6. Measurement Uncertainty ............................................................................ 24 HBCS Report # EMC_25042_2 Rev1 Page 4 of 24 EXECUTIVE SUMMARY 1. Testing Summary These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15.209. All tests were conducted using measurement procedure from ANSI C63.4-2014, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9kHz to 40GHz and ANSI C63.10-2020 Procedures for Compliance Testing of Unlicensed Wireless Devices as appropriate. Test Name Test Method/Standard Result Comments Unintentional Radiated Emissions 15.109 Pass A/C Power Line Conducted Emissions 15.207(a) Pass Occupied Bandwidth 15.215 Pass Radiated Fundamental Emissions 15.209(a) Pass Radiated Spurious Emissions 15.209(a), 15.205, 15.35(C), KDB 996369 Pass HBCS Report # EMC_25042_2 Rev1 Page 5 of 24 EQUIPMENT CONFIGURATION 1. Overview H.B Compliance Solutions was contracted by Lodestar Technology, Inc. to perform testing on the LNK Charging Pad under quotation number Q25091001. This document describes the test setups, test methods, required test equipment, and the test limit criteria used to perform compliance testing of the Lodestar Technology, Inc. LNK Charging Pad. The tests were based on FCC Part 15 Rules. The tests described in this document were formal tests as described with the objective of the testing was to evaluate compliance of the Equipment Under Test (EUT) to the requirements of the aforementioned specifications. Lodestar Technology, Inc. is to retain a copy of this document and it should be kept on file for at least five years after the manufacturing of the EUT has been permanently discontinued. The results obtained relate only to the item(s) tested. Product Name: LNK Charging Pad Model(s) Tested: N/A FCC ID: 2BSUV-08-00024-01 Supply Voltage Input: Primary Power: 120VAC Frequency Range: 190-200 kHz No. of Channels: 1 Type(s) of Modulation: Sinewave Range of Operation Power: - Emission Designator: N/A Channel Spacing(s) None Test Item: Pre-Production Type of Equipment: Fixed Antenna Requirement (§15.203): Type of Antenna: Integral Loop Gain of Antenna: 0dBi Environmental Test Conditions: Temperature: 15-35⁰C Humidity: 30-60% Barometric Pressure: 860-1060 mbar Modification to the EUT: None Evaluated By: Staff at H.B Compliance Sol…

Text truncated - open the document above for the full version.

SECTION 1 | GENERAL DESCRIPTION Page 1 of 8 Lodestar Charger Antenna Exhibits 28-02-00003-01 Pub. 10 February 2026 [Lodestar] – CHARGER ANTENNA EXHIBITS 1 GENERAL DESCRIPTION This document presents the antenna exhibits for the antennas integrated on the charger main board for the Lodestar LNK9 project. It provides the relevant performance characteristics as implemented in the charger hardware. These exhibits are intended to document and substantiate the antenna implementation for review, validation, and compliance purposes within the scope of the LNK9 project. 2 EXHIBITS 2.1 BLUETOOTH MODULE Figure 1: Antenna Radiation Pattern when Phi = 0 deg. SECTION 2 | EXHIBITS Page 2 of 8 Lodestar Charger Antenna Exhibits 28-02-00003-01 Pub. 10 February 2026 Figure 2: Antenna Radiation Pattern when Phi = 90 deg. SECTION 2 | EXHIBITS Page 3 of 8 Lodestar Charger Antenna Exhibits 28-02-00003-01 Pub. 10 February 2026 Figure 3: Antenna Radiation Pattern when Theta = 0 deg. SECTION 2 | EXHIBITS Page 4 of 8 Lodestar Charger Antenna Exhibits 28-02-00003-01 Pub. 10 February 2026 2.2 CELLULAR MODULE Figure 4: Radiation Patterns for ANT-LPC-FPC-ccc Antenna (1) SECTION 2 | EXHIBITS Page 5 of 8 Lodestar Charger Antenna Exhibits 28-02-00003-01 Pub. 10 February 2026 Figure 5: Radiation Patterns for ANT-LPC-FPC-ccc Antenna (2) SECTION 2 | EXHIBITS Page 6 of 8 Lodestar Charger Antenna Exhibits 28-02-00003-01 Pub. 10 February 2026 Figure 6: Radiation Patterns for ANT-LPC-FPC-ccc Antenna (3) SECTION 2 | EXHIBITS Page 7 of 8 Lodestar Charger Antenna Exhibits 28-02-00003-01 Pub. 10 February 2026 2.3 WIFI MODULE Figure 7: RNBD350 Antenna Radiation Pattern when Phi = 0 deg. Figure 8: RNBD350 Antenna Radiation Pattern when Phi = 90 deg. SECTION 2 | EXHIBITS Page 8 of 8 Lodestar Charger Antenna Exhibits 28-02-00003-01 Pub. 10 February 2026 Figure 9: RNBD350 Antenna Radiation Pattern when Theta = 0 deg. Figure 10: RNBD350 Antenna Radiation 3D Pattern