2BTVL-SAFEWAVEWireless Charger

Product Name : Wireless Charger Model Name: JDS9301S Modulation Type: ASK Power Rating: DC 5V From USB This product realizes short distance and small power radio transmission through magnetic induction, suitable for charging and powering GPS, MP3, fire fighting, waterproof light and small power digital products. FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

(Safewave Technology Corporation) (2026.01.20) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID:2BTVL-SAFEWAVE) [Safewave Technology Corporation] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber-security or anti-virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely, (Applicant signature) (Applicant printed name) Jared Gabbard (Safewave Technology Corporation) (2026.01.20) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID:2BTVL-SAFEWAVE) [Safewave Technology Corporation] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Jared Gabbard

U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Safewave Technology Corporation FRN: 0037782398 Contact Name: Jared Gabbard Address: 2 W Pike St. Unit 3 Covington, KY 41011, USA Telephone No: 513-304-1186 Email: [email protected] This letter is to confirm that we (Safewave Technology Corporation) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: 2026/ 01/14 Signed by (Printed Name/Title): Jared Gabbard / Manager The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Safewave Technology Corporation Grantee Code:2BTVL FCC ID: 2BTVL-SAFEWAVE FRN: 0037782398 Email:[email protected] Contact Name: Jared Gabbard Address: 2 W Pike St. Unit 3 Covington, KY 41011, USA Telephone No: 513-304-1186 Applicant Signature: Date: 2026/ 01/14 Signed by (Printed Name/Title): Jared Gabbard / Manager Jared Gabbard (Jan 20, 2026 10:26:53 EST) Jared Gabbard Jared Gabbard (Jan 20, 2026 10:26:53 EST) Jared Gabbard Jared Gabbard (Jan 20, 2026 10:26:53 EST) Jared Gabbard FCC ID：2BTVL-SAFEWAVE (002) Final Audit Report2026-01-20 Created:2026-01-19 By:COURTNEY PHILLIPS ([email protected]) Status:Signed Transaction ID:CBJCHBCAABAA9_y6i1QjJvoSmNimlL-L7p7pHTI0r3G7 History Document created by COURTNEY PHILLIPS ([email protected]) 2026-01-19 - 12:51:43 PM GMT Document emailed to Jared Gabbard ([email protected]) for signature 2026-01-19 - 12:51:49 PM GMT Email viewed by Jared Gabbard ([email protected]) 2026-01-20 - 3:26:15 PM GMT Document e-signed by Jared Gabbard ([email protected]) Signature Date: 2026-01-20 - 3:26:53 PM GMT - Time Source: server Agreement completed. 2026-01-20 - 3:26:53 PM GMT

Safewave Technology Corporation 2026.01.20 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR E UT NAME: Wireless Charger Trademark: N/A MODEL : JDS9301S FCC ID : 2BTVL-SAFEWAVE To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the -Block Diagram -Schematics -Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Jared Gabbard /Manager Contact information / address: 2 W Pike St. Unit 3 Covington, KY 41011, USA

Safewave Technology Corporation 2026.01.20 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Jared Gabbard /Manager Contact information / address: 2 W Pike St. Unit 3 Covington, KY 41011, USA

FCC ID: 2BTVL-SAFEWAVE External Photos FCC ID: 2BTVL-SAFEWAVE FCC ID: 2BTVL-SAFEWAVE FCC ID: 2BTVL-SAFEWAVE

FCC ID:2BTVL-SAFEWAVE Label location

FCC ID: 2BTVL-SAFEWAVE Internal Photos FCC ID: 2BTVL-SAFEWAVE

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. MPE Test Report Report No.: STS2512457H01 Issued for Safewave Technology Corporation 2 W Pike St. Unit 3 Covington, KY 41011, USA Product Name: Wireless Charger Brand Name: N/A Model Name: JDS9301S Series Model(s): N/A FCC ID: 2BTVL-SAFEWAVE Test Standard: FCC CFR 47 part 1, 1.1310 Page 2 of 14 Report No.: STS2512457H01 TEST RESULT CERTIFICATION Applicant’s Name ................... : Safewave Technology Corporation Address ................................. : 2 W Pike St. Unit 3 Covington, KY 41011, USA Manufacturer's Name ............. : Safewave Technology Corporation Address ................................. : 2 W Pike St. Unit 3 Covington, KY 41011, USA Product Description Product Name ........................ : Wireless Charger Brand Name ........................... : N/A Model Name ........................ : JDS9301S Series Model(s) ...................... : N/A Standards .............................. : FCC CFR 47 part 1, 1.1310 Test Procedure ..................... : KDB 680106 D01 Wireless Power Transfer v04 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ............................ : Date of receipt of test item ..... : 19 Dec. 2025 Date of performance of tests .. : 19 Dec. 2025 to 14 Jan. 2026 Date of Issue .......................... : 14 Jan. 2026 Test Result ............................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 14 Report No.: STS2512457H01 Table of Contents Page 1. SUMMARY OF TEST RESULTS 5 1.1 TEST FACTORY 5 1.2 MEASUREMENT UNCERTAINTY 5 1.3 GENERAL DESCRIPTION OF THE EUT 6 1.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 7 1.6 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 7 2. COIL SPECIFICATIONS 7 2.1 COIL SIZE 8 2.2 LOCATION(S) – COIL TO THE OUTER SURFACE OF THE ENCLOSURE(S) 8 3. MAXIMUM PERMISSIBLE EXPOSURE 9 3.1MEASURING STANDARD 9 3.2 REQUIREMENTS 9 3.3TEST PROCEDURE 11 3.4 TEST SETUP 11 3.5 TEST RESULTS 12 3.6 MAXIMUM PERMISSIBLE EXPOSURE 13 Page 4 of 14 Report No.: STS2512457H01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 14 Jan. 2026 STS2512457H01 ALL Initial Issue Page 5 of 14 Report No.: STS2512457H01 1. SUMMARY OF TEST RESULTS 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainly 1 H-filed ±0.83dB 2 E-filed ±0.91dB Page 6 of 14 Report No.: STS2512457H01 1.3 GENERAL DESCRIPTION OF THE EUT Product Name Wireless Charger Brand N/A Model Number JDS9301S Series Model(s) N/A Model Difference N/A Equipemnt Category Non-ISM frequency Antenna Type loop coil antenna Operating frequency 550-600kHz Modulation Type ASK Power Rating DC 5V From USB Adapter N/A Battery N/A Wireless charging power 2.5W Hardware version number N/A Software version number N/A Connecting I/O Port(s) Please refer to the Note 1. Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User Manual. 2. Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector NOTE 1 N/A N/A Coil N/A Antenna The EUT antenna is Coil Antenna. No antenna other than that furnished by the responsible party shall be used with the device. Page 7 of 14 Report No.: STS2512457H01 1.4 DESCRIPTION OF THE TEST MODES Equipment under test was operated during the measurement under the following conditions: Test Mode Description Mode 1 AC Adapter + EUT + Load(2.5W, 550-600KHz) (Battery Status: < 1%) Record Mode 2 AC Adapter + EUT + Load(2.5W, 550-600KHz) (Battery Status: < 50%) Record Mode 3 AC Adapter + EUT + Load(2.5W, 550-600KHz) (Battery Status: < 99%) Record Note: All test modes were pre-tested, but we only recorded the worst case in this report. 1.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until Electric and Magnetic field Probe - Analyzer NARDA EHP-200A 180ZX10220 2025.02.22 2026.02.21 1.6 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS Item Equipment Mfr/Brand Model/Type No. Note E-1 Adapter ZTC NB-A515A Auxiliary E-2 Load N/A N/A Auxiliary Note: (1) For detachable type I/O cable should be specified the length in cm in『Length』column. (2) “YES” is means “with core”; “NO” is means “without core”. 2. COIL SPECIFICATIONS ltem Parameter Input inductance: L1: 3.8uH-4.4uH Material of enclosure(s): Silk wrapped wire Number of turns: Transmitter 1: 10turns Page 8 of 14 Report No.: STS2512457H01 2.1 COIL SIZE Unit: mm A B 23.1±0.5 16.2±0.5 2.2 LOCATION(S) – COIL TO THE OUTER SURFACE OF THE ENCLOSURE(S) Unit: mm Front A Rear B Left C Right D Top E Bottom F 4.9 4.9 4.9 4.9 1.5 5.8 Front Left Rear Right Top Bottom Page 9 of 14 Report No.: STS2512457H01 3. MAXIMUM PERMISSIBLE EXPOSURE 3.1MEASURING STANDARD According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of …

Text truncated - open the document above for the full version.

Manufacturer：Shenzhen Jing Ding Sheng Electronics Co., Ltd ANT Gain：0dbi Antenna Type: Coil antenna unit：mm A B 23.1±0.5 16.2±0.5

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.: STS2512457W01 Issued for Safewave Technology Corporation 2 W Pike St. Unit 3 Covington, KY 41011, USA Product Name: Wireless Charger Brand Name: N/A Model Name: JDS9301S Series Model(s): N/A FCC ID: 2BTVL-SAFEWAVE Test Standards: FCC Part 15 Subpart C Page 2 of 23 Report No.: STS2512457W01 TEST REPORT Applicant’s Name ................... : Safewave Technology Corporation Address ................................. : 2 W Pike St. Unit 3 Covington, KY 41011, USA Manufacturer's Name ............. : Safewave Technology Corporation Address ................................. : 2 W Pike St. Unit 3 Covington, KY 41011, USA Product Description Product Name ........................ : Wireless Charger Brand ..................................... : N/A Model Number ....................... : JDS9301S Series Model(s)...................... : N/A Test Standards ..................... : FCC Part 15 Subpart C Test Procedure ...................... : ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ...............................: Date of receipt of test item ..........: 19 Dec. 2025 Date (s) of performance of tests .: 19 Dec. 2025 to 14 Jan. 2026 Date of Issue ............................. : 14 Jan. 2026 Test Result ..................................: Pass Testing Engineer : (Aaron Bu) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 23 Report No.: STS2512457W01 Table of Contents Page 1. SUMMARY OF TEST RESULTS 5 1.1 TEST FACTORY 5 1.2 MEASUREMENT UNCERTAINTY 5 2. GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF THE EUT 6 2.2 DESCRIPTION OF THE TEST MODES 7 2.3 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 8 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 9 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 10 3. CONDUCTED EMISSION TEST RESULT (SECTION 15.207) 11 3.1 POWER LINE CONDUCTED EMISSION LIMITS 11 3.2 TEST PROCEDURE 12 3.3 TEST SETUP 12 3.4 EUT OPERATING CONDITIONS 12 3.5 TEST RESULTS 13 4. RADIATED& FIELD EMISSION TEST RESULT (SECTIOU 15.209) 15 4.1 LIMIT 15 4.2 TEST PROCEDURE 15 4.3 TEST SETUP 16 4.4 TEST RESULTS 17 4.4.1 SPURIOUS RADIATED EMISSION BELOW 30 MHZ 17 5. 20 DB BANDWIDTH TEST 21 5.1 LIMIT 21 5.2 TEST SETUP 21 5.3 TEST RESULTS 21 6. ANTENNA REQUIREMENTS 22 6.1 LIMIT 22 6.2 TEST RESULTS 22 APPENDIX-PHOTOS OF TEST SETUP 23 Page 4 of 23 Report No.: STS2512457W01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 14 Jan. 2026 STS2512457W01 ALL Initial Issue Page 5 of 23 Report No.: STS2512457W01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.209(a) Radiated emission, Spurious Emission PASS 2.1049 20 dB Bandwidth PASS 15.203 Antenna Requirement PASS 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.755dB 2 Unwanted Emissions, conducted ±2.874dB 3 All emissions, radiated 9K-30MHz ±3.80dB 4 All emissions, radiated 30M-1GHz ±4.18dB 5 All emissions, radiated 1G-6GHz ±4.90dB 6 All emissions, radiated>6G ±5.24dB 7 Conducted Emission (9KHz-150KHz) ±2.19dB 8 Conducted Emission (150KHz-30MHz) ±2.53dB 9 Occupied Channel Bandwidth ±3.5% 10 Power Spectral Density, conducted ±1.245dB 11 Duty Cycle ±3.2% Page 6 of 23 Report No.: STS2512457W01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name Wireless Charger Brand N/A Model Number JDS9301S Series Model(s) N/A Model Difference N/A Equipemnt Category Non-ISM frequency Antenna Type loop coil antenna Operating frequency 550-600kHz Modulation Type ASK Power Rating DC 5V From USB Adapter N/A Battery N/A Wireless charging power 2.5W Hardware version number N/A Software version number N/A Connecting I/O Port(s) Please refer to the Note 1. Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User Manual. 2. Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector NOTE 1 N/A N/A Coil N/A Antenna Page 7 of 23 Report No.: STS2512457W01 2.2 DESCRIPTION OF THE TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 TX Mode(550-600KHz) For Conducted Emission Final Test Mode Description Mode 1 TX Mode(550-600KHz) For Radiated Emission Final Test Mode Description Mode 1 TX Mode(550-600KHz) Page 8 of 23 Report No.: STS2512457W01 2.3 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED During testing channel & power controlling software provided by the customer was used to control the oper…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID:2BTVL-SAFEWAVE Conducted emissions 30MHz-1GHz Page 2 of 2 FCC ID:2BTVL-SAFEWAVE Spurious emissions