2BTY9-SP01Jucani Speaker-01

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Statement

AttestationStatements (1/22/2026) TO:FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046,USA RE:AttestationStatementsPart2.911(d)(7)requestfor(2BTY9-SP01) (jucaniinc),theundersigned,herebyauthorize(jucaniinc)toactasourdesignated U.S.agentforserviceofprocess,(jucaniinc)acceptsto maintainanagentfornolessthanoneyearafterthegranteehasterminatedall marketingandimportationortheconclusionofanyCommission-relatedproceeding involvingtheequipment. (jucaniinc)acceptstheresponsibilitytoactasdesignatedU.S.agentfor serviceofprocess. ApplicantInformation： Companyname:jucaniinc FRN:0037816311 ContactName:BILLJIANG Address:SuiteA2,7498ColchesterCourt,SanDiego,CA,US,92154 TelephoneNo:4709397499 Email:[email protected] Signature [BILLJIANG] U.S.AgentInformation: CompanyName:jucaniinc FRN:0037816311 Address:SuiteA2,7498ColchesterCourt,SanDiego,CA,US,92154FRN:0033767856 ContactName:BILLJIANG TelephoneNo:4709397499 Email:[email protected] Signature[BILLJIANG]

(jucaniinc) (1/19/26) EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(i)requestfor( 2BTY9-SP01 ) [jucaniinc](“theapplicant”)certifiesthattheequipmentforwhichauthorizationis soughtisnot“covered”equipmentprohibitedfromreceivinganequipment authorizationpursuanttosection2.903oftheFCCrules. Wealsocertifythat,asofthedateofthefilingoftheapplication,theequipmentdoes notutilizecyber-securityoranti-virussoftwarefromKasperskyLab,Inc,oranyofits successorsandassignees,whichisalsoonthe“coveredlist”. Sincerely, (Applicantsignature) (Applicantprintedname) BILLJIANG (jucaniinc) (1/19/26) EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(ii)requestfor(2BTY9-SP01) [jucaniinc](“theapplicant”)certifiesthat,asofthedateofthefilingoftheapplication, theapplicantisnotidentifiedontheCoveredListasanentityproducing“covered” equipment. Sincerely, (Applicantsignature) (Applicantprintedname) BILLJIANG

APPLICANTCOMPANYLETTERHEAD We（jucaniinc）ProducemodelSP01,andseries models:SP-Flow-5W-Max-1,thedifferenceisOnlythemodelnameis different，therestisthesame. Company：jucaniinc Date：2026-1-30 Signature:

jucaniinc (1/22/26) EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:CONFIDENTIALITYREQUESTFOR(JucaniSpeaker-01/2BTY9-SP01) ToWhomItMayConcern: Thisletterservesasanofficialrequestforconfidentialityundersections0.457and0.459 ofCFR47.Wehaverequestedthatthe(Blockdiagram,circuitdiagram,operational description,PCBLayout)requiredtobesubmittedwiththisapplication bepermanentlywithheldfrompublicreview. SPECIFYREASONFORREQUEST(i.e.theabovedocumentsarecompany proprietaryinformationthatcouldnevergetintothepossessionofyour competition). Pleasecontactmeifthereisanyinformationyoumayneed. Sincerely,

jucaniinc (1/22/26) EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:LETTEROFAGENTAUTHORIZATION ToWhomItMayConcern: We,theundersigned,herebyauthorize( ShenzhenHaiyunStandardTechnicalCO.,Ltd.)toacton ourbehalfinallmattersrelatingtoapplicationforequipmentauthorization, includingthesigningofalldocumentsrelatingtothesematters. Wealsoherebycertifythatnopartytotheapplicationauthorizedhereunderissubjecttothe denialofbenefits,includingFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuseAct of1988,21U.S.C.853(a). Thisagreementexpiresoneyearfromthecurrentdate. Sincerely,

FCC ID: 2BTY9-SP01 Page 1 / 3 EUT EXTERNAL PHOTO EUT Photo EUT Photo FCC ID: 2BTY9-SP01 Page 2 / 3 EUT Photo EUT Photo FCC ID: 2BTY9-SP01 Page 3 / 3 EUT Photo EUT Photo

项目名称：SP-Flow-5W-Max-1 版本号：1.0 设计时间：20260112 设计师 表面 LOGO/CMF说明 工艺：粘胶、丝印 制作工序： 颜色：黑色 工艺要求： 图形工整、无变形 颜色均匀、边缘清晰 附着力强、不能轻易刮掉 如有其他特殊要求，请写明 比例：1:1 单位:mm

FCC ID: 2BTY9-SP01 Page 1 / 3 EUT INTERNAL PHOTOS EUT Photo EUT Photo FCC ID: 2BTY9-SP01 Page 2 / 3 EUT Photo EUT Photo FCC ID: 2BTY9-SP01 Page 3 / 3 EUT Photo EUT Photo BT& 2.4G WIFII antenna

HY- FCC 2.1093 Ver.1.1 Page 1 of 5 Report No.: RF251229035-01-002 FCC RF EXPOSURE REPORT FCC ID: 2BTY9-SP01 Tes t Report No...........: RF251229035-01-002 Product(s) Name.........: Jucani Speaker-01 Model(s)....................: SP01, SP-Flow-5W-Max-1 Trade Mark................: Applica nt...................: jucani inc Address.....................: Suite A2, 7498 Colchester Court San Diego, California 92154 Receipt Date..............: 2025.12.31 Test Date...................: 2026.01.07 ~ 2026.01.19 Issued Date................: 2026.01.20 Standards..................: CFR47 FCC Part 1: Section 1.1310; CFR47 FCC Part 2: Section 2.1093; FCC KDB Publication 447498 D04; FCC KDB Publication 865664 D02 v01r02 Testing Laboratory......: Shenzhen Haiyun Standard Technical Co., Ltd. Prepared By: Checked By: Approved By: Jason Huang Black Ding Tim Zhang HY-FCC 2.1093 Ver.1.1 Page 2 of 5 Report No.: RF251229035-01-002 History of this test report Original Report Issue Date: 2026.01.20 ● No additional attachment ○ Additional attachments were issued following record Attachment No. Issue Date Description HY-FCC 2.1093 Ver.1.1 Page 3 of 5 Report No.: RF251229035-01-002 1. MPE CALCULATION METHOD Limit Calculation Method ERP/EIRP = P T +G T −L C ERP/EIRP is the equivalent (or effective) radiated power [in same units as P T , typically dBW, dBm, or power spectral density (psd)], relative to either a dipole antenna (ERP) or an isotropic antenna (EIRP). P T is the transmitter output power, in dBW, dBm, or psd (power over a specified reference bandwidth). G T is the gain of the transmitting antenna, in dBd (ERP) or dBi (EIRP). L C is the signal attenuation in the connecting cable between the transmitter and the antenna, in dB. Table for Filed Antenna For BDR+EDR Antenna gain Antenna Type -0.58dBi PCB antenna HY-FCC 2.1093 Ver.1.1 Page 4 of 5 Report No.: RF251229035-01-002 2. TEST RESULTS Worst case as below Mode Output power to antenna (dBm) Ant gain (dBi) EIRP (dBm) ERP (dBm) ERP(mw) Distance (cm) Pth (mW) BDR+EDR 1.76 -0.58 1.18 -0.97 0.8 0.5 2.79 Note: 1. ERP = EIRP −2.15 dB 2. 0.8mW<2.79mw  Conclusion The SAR evaluation is not required HY-FCC 2.1093 Ver.1.1 Page 5 of 5 Report No.: RF251229035-01-002 Statement 1. The report is invalid without the official seal or special seal of Shenzhen Haiyun Standard Technical Co., Ltd. (hereinafter referred to as the unit). 2. The report is invalid without the signature of the approver. 3. The report is invalid if altered arbitrarily. 4. The report shall not be partially copied without the written approval of the unit. 5. The reported test results are only valid for the tested samples. 6. If there is any objection to the test report, it shall be submitted to the test unit within 15 days from the date of receiving the report, and the overdue shall not be accepted. Shenzhen Haiyun Standard Technical Co., Ltd. Address: Room 110, 111, 112, 113, 115, 116, Block B, Jinyuan Business Building, No. 302, Xixiang Avenue, Labor Community, Xixiang Street, Baoan District, Shenzhen, China （END OF REPORT）

HY-FCC part 15C-BT Ver.1.1 Page 1 of 91 Report No.: RF251229035-01-001 RF TEST REPORT FCC ID: 2BTY9-SP01 Test Report No...........: RF251229035-01-001 Product(s) Name.........: Jucani Speaker-01 Model(s)....................: SP01, SP-Flow-5W-Max-1 Trade Mark................: Applica nt...................: jucani inc Address.....................: Suite A2, 7498 Colchester Court San Diego, California 92154 Receipt Date..............: 2025.12.31 Test Date...................: 2026.01.07 ~ 2026.01.19 Issued Date................: 2026.01.20 Standards..................: 47 CFR FCC Part 15, Subpart C(Section 15.247) ANSI C63.10:2020 Testing Laboratory......: Shenzhen Haiyun Standard Technical Co., Ltd. Prepared By: Checked By: Approved By: Jason Huang Black Ding Tim Zhang HY-FCC part 15C-BT Ver.1.1 Page 2 of 91 Report No.: RF251229035-01-001 Table of Contents 1 . SUMMARY OF TEST RESULTS 6 1.1 TEST FACILITY 7 1.2 MEASUREMENT UNCERTAINTY 7 1.3 TEST ENVIRONMENT CONDITIONS 7 2 . GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF EUT 8 2.2 DESCRIPTION OF TEST MODES 9 2.3 PARAMETERS OF TEST SOFTWARE 10 2.4 SUPPORT UNITS 10 3 . AC POWER LINE CONDUCTED EMISSIONS 11 3.1 LIMIT 11 3.2 TEST PROCEDURE 11 3.3 DEVIATION FROM TEST STANDARD 11 3.4 TEST SETUP 12 3.5 EUT OPERATING CONDITIONS 12 3.6 TEST RESULTS 12 4 . RADIATED EMISSIONS 13 4.1 LIMIT 13 4.2 TEST PROCEDURE 14 4.3 DEVIATION FROM TEST STANDARD 15 4.4 TEST SETUP 15 4.5 EUT OPERATING CONDITIONS 16 4.6 TEST RESULTS - 9 KHZ TO 30 MHZ 16 4.7 TEST RESULTS - 30 MHZ TO 1000 MHZ 16 4.8 TEST RESULTS - ABOVE 1000 MHZ 16 5 . NUMBER OF HOPPING FREQUENCY 17 5.1 LIMIT 17 5.2 TEST PROCEDURE 17 5.3 DEVIATION FROM STANDARD 17 5.4 TEST SETUP 17 5.5 EUT OPERATION CONDITIONS 17 5.6 TEST RESULTS 17 6 . AVERAGE TIME OF OCCUPANCY 18 6.1 LIMIT 18 HY-FCC part 15C-BT Ver.1.1 Page 3 of 91 Report No.: RF251229035-01-001 6.2 TEST PROCEDURE 18 6.3 DEVIATION FROM STANDARD 18 6.4 TEST SETUP 18 6.5 EUT OPERATION CONDITIONS 18 6.6 TEST RESULTS 18 7 . HOPPING CHANNEL SEPARATION 19 7.1 LIMIT 19 7.2 TEST PROCEDURE 19 7.3 DEVIATION FROM STANDARD 19 7.4 TEST SETUP 19 7.5 EUT OPERATION CONDITIONS 19 7.6 TEST RESULTS 19 8 . BANDWIDTH 20 8.1 LIMIT 20 8.2 TEST PROCEDURE 20 8.3 DEVIATION FROM STANDARD 20 8.4 TEST SETUP 20 8.5 EUT OPERATION CONDITIONS 20 8.6 TEST RESULTS 20 9 . MAXIMUM OUTPUT POWER 21 9.1 LIMIT 21 9.2 TEST PROCEDURE 21 9.3 DEVIATION FROM STANDARD 21 9.4 TEST SETUP 21 9.5 EUT OPERATION CONDITIONS 21 9.6 TEST RESULTS 21 10 . CONDUCTED SPURIOUS EMISSION 22 10.1 LIMIT 22 10.2 TEST PROCEDURE 22 10.3 DEVIATION FROM STANDARD 22 10.4 TEST SETUP 22 10.5 EUT OPERATION CONDITIONS 22 10.6 TEST RESULTS 22 11 . MEASUREMENT INSTRUMENTS LIST 23 12 . ANTENNA REQUIREMENT 24 APPENDIX A - AC POWER LINE CONDUCTED EMISSIONS 25 APPENDIX B - RADIATED EMISSION - 9 KHZ TO 30 MHZ 28 HY-FCC part 15C-BT Ver.1.1 Page 4 of 91 Report No.: RF251229035-01-001 APPENDIX C - RADIATED EMISSION - 30 MHZ TO 1000 MHZ 29 APPENDIX D - RADIATED EMISSION - ABOVE 1000 MHZ 32 APPENDIX E - NUMBER OF HOPPING FREQUENCY 33 APPENDIX F - AVERAGE TIME OF OCCUPANCY 36 APPENDIX G - HOPPING CHANNEL SEPARATION 47 APPENDIX H - BANDWIDTH 50 APPENDIX I - MAXIMUM OUTPUT POWER 61 APPENDIX J - CONDUCTED SPURIOUS EMISSION 67 APPENDIX K - DECLARATION FOR BLUETOOTH DEVICE 88 HY-FCC part 15C-BT Ver.1.1 Page 5 of 91 Report No.: RF251229035-01-001 HISTORY OF THIS TEST REPORT Original Report Issue Date: 2026.01.20 ● No additional attachment ○ Additional attachments were issued following record Attachment No. Issue Date Description HY-FCC part 15C-BT Ver.1.1 Page 6 of 91 Report No.: RF251229035-01-001 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standard(s): FCC CFR Title 47, Part 15, Subpart C Standard(s) Section Test Item Test Result Judgment Remark 15.207 AC Power Line Conducted Emissions APPENDIX A PASS ------ 15.247(d) 15.205(a) 15.209(a) Radiated Emission APPENDIX B APPENDIX C APPENDIX D PASS ------ 15.247 (a)(1)(iii) Number of Hopping Frequency APPENDIX E PASS ------ 15.247 (a)(1)(iii) Average Time of Occupancy APPENDIX F PASS ------ 15.247(a)(1) Hopping Channel Separation APPENDIX G PASS ------ 15.247(a)(1) Bandwidth APPENDIX H PASS ------ 15.247(a)(1) Maximum Output Power APPENDIX I PASS ------ 15.247(d) Conducted Spurious Emission APPENDIX J PASS ------ 15.203 Antenna Requirement ------ PASS Note(2) Note: (1) “N/A” denotes test is not applicable in this test report (2) The device what use a permanently attached antenna were considered sufficient to comply with the provisions of 15.203. HY-FCC part 15C-BT Ver.1.1 Page 7 of 91 Report No.: RF251229035-01-001 1.1 TEST FACILITY Company: Shenzhen Haiyun Standard Technical Co., Ltd. Address: No. 110-113, 115, 116, Block B, Jinyuan Business Building, Bao'an District, Shenzhen, China CNAS Registration Number: CNAS L18252 CAB identifier: CN0145 A2LA Certificate Number: 6823.01 1.2 MEASUREMENT UNCERTAINTY ISO/IEC 17025 requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2)) Uncertainty Parameter Uncertainty Occupied Channel Bandwidth ±102kHz RF power conducted ±0.243dB Power Spectral Density ±0.743dB Conducted Spurious Emission ±1.328dB Time ±0.19％ Conducted emission(9kHz~30MHz) AC main ±2.68dB Radiated emission(9kHz~30MHz) ±3.50dB Radiated emission (30MHz~1GHz) ±4.20dB Radiated emission (1GHz~18GHz) ±5.10dB Radiated emission (18GHz~40GHz) ±5.26dB Note: Unless specifically mentioned, the uncertainty of measurement has not been taken into account to declare the compliance or non-compliance to the specification. 1.3 TEST ENVIRONMENT CONDITIONS Test Item Temperature Humidity Test Voltage Tested By AC Power Line Conducted Emissions 22.9°C 48% AC 120V/60Hz Keith Huang Radiated Emissions-9 kHz to 30 MHz 22.7°C 43% AC 120V/60Hz Lemon He Radiated Emissions-30 MHz to 1000 MHz 22.7°C 43% AC 120V/60Hz Lemon…

Text truncated - open the document above for the full version.

AC6965EDatasheet AC6965EDatasheet ZhuhaiJieliTechnologyCo.,LTD Version：V1.0 Date：2020.06.01 Copyright©ZhuhaiJieliTechnologyCo.,LTD.Allrightsreserved. AC6965EDatasheet 2 Confidential TheinformationcontainedhereinistheexclusivepropertyofJIELIandshallnotbedistributed,reproduced,ordisclosedinwholeorinpartwithout priorwrittenpermissionofJIELI. AC6965EFeatures CPU 32-bitDSPsupportshardwareFloatPoint Unit(FPU) Upto160MHzprogrammableprocessor 64Vectoredinterrupts 4Levelsinterruptpriority DSPAudioProcessing SBC,AACAudiodecodessupportedforBT audio mSBCvoicecodecssupportedforBTphone SupportsMP2,MP3,WMA,APE,FLAC, AAC,MP4,M4A,WAV,AIF,AIFCaudio decoding PacketLossConcealment(PLC)forvoice processing Acousticechocancellation/suppression (AEC,AES) Single/DualMICEnvironmentalNoise Cancellation(ENC) Multi-bandDRClimiter 10-bandEQconfigurationforvoiceEffects AudioCodec Onechannels16-bitDAC,SNR>=95dB Onechannels16-bitADC,SNR>=90dB Samplingratesof 8KHz/11.025KHz/16KHz/22.05KHz/24KHz/ 32KHz/44.1KHz/48KHzaresupported OneanalogMICamplifier,build-inMICbias generator SupportstwoPDMdigitalMICinputs TwochannelsMonoanalogMUX Supportscap-less,single-ended,and differentialmodeattheDACpath Supports16ohmand32ohmSpeakerloading Bluetooth CompliantwithBluetooth V5.1+BR+EDR+BLEspecification Meetclass1class2andclass3transmitting powerrequirement SupportGFSKandπ/4DQPSKallpacket types Provides+6dbmtransmittingpower receiverwith-90dBmsensitivity FastAGCforenhanceddynamicrange Supports a2dp\avctp\avdtp\avrcp\hfp\spp\smp\att\gap\g att\rfcomm\sdp\l2capprofile Peripherals OnefullspeedUSB2.0OTGcontroller Sixmulti-function32-bittimers,support captureandPWMmode Threefull-duplexbasicUART,UART0and UART1supportsDMAmode OnehardwareIICinterfacesupportshostand devicemode 10-bitADCforanalogsampling Externalwakeup/interruptonallGPIOs PMU LowvoltageLDOforinternaldigitaland analogcircuitsupply 3uAcurrentconsumptioninthesoft-offmode Built-inLDOforthecore,I/O,Bluetoothand flash VBATis2.2Vto5.5V VDDIOis2.2Vto3.6V Packages QSOP24 Temperature Operatingtemperature:-20°Cto+70°C Storagetemperature:-65°Cto+150°C Applications Bluetoothspeaker AC6965EDatasheet 3 Confidential TheinformationcontainedhereinistheexclusivepropertyofJIELIandshallnotbedistributed,reproduced,ordisclosedinwholeorinpartwithout priorwrittenpermissionofJIELI. 1、PinDefinition 1.1PinAssignment Figure1-1AC6965EPackageDiagram AC6965EDatasheet 4 Confidential TheinformationcontainedhereinistheexclusivepropertyofJIELIandshallnotbedistributed,reproduced,ordisclosedinwholeorinpartwithout priorwrittenpermissionofJIELI. 1.2PinDescription Table1-1AC6965EPinDescription PIN NO. Name I/O Type Drive (mA) FunctionOtherFunction 1PC5I/O24/8GPIO SD0CLKA：SD0Clock(A); SPI1DOB：SPI1DataOut(B); IIC_SDA_B：IICSDA(B); ADC12：ADCInputChannel12; TMR1：Timer1ClockInput; UART2RXD：Uart2DataIn(D); 2PC4I/O24/8GPIO SD0CMDA：SD0Command(A); SPI0_DAT3AB(3)：SPI0Data3(AB)； SPI1CLKB：SPI1Clock(B); IIC_SCL_B：IICSCL(B); ADC11：ADCInputChannel11; PWM1：Timer1PWMOutput； UART2TXD：Uart2DataOut(D)； 3 USBDMI/O4 USBNegative Data (pulldown) SPI2DOB：SPI2DataOut(B); IIC_SDA_A：IICSDA(A); ADC14：ADCInputChannel14; UART1RXD：Uart1DataIn(D); PC3I/O24/8GPIO SD0DAT0A ： SD0Data0(A); SPI0_DAT2B(2) ： SPI0Data2(B) ； SPI1DIB ： SPI1DataIn(B); CAP2 ： Timer2Capture; UART0TXD ： Uart0DataOut(D) ； UART0RXD ： Uart0DataIn(D); 4USBDPI/O4 USBPositive Data (pulldown) SPI2CLKB：SPI2Clock(B); IIC_SCL_A：IICSCL(A); ADC13：ADCInputChannel13; UART1TXD：Uart1DataOutput(D)； 5PA4I/O24/8 SD0CMDC：SD0Command(C) AMUX0R：AnalogChannel0Right; PLNK_DAT1：PLNKData1； UART1_RTS：Uart1Requesttosend； ADC3：ADCInputChannel3; TMR4：Timer4ClockInput; UART2RXA：Uart2DataIn(A); 6PA3I/O24/8SD0DATC：SD0Data(C); AC6965EDatasheet 5 Confidential TheinformationcontainedhereinistheexclusivepropertyofJIELIandshallnotbedistributed,reproduced,ordisclosedinwholeorinpartwithout priorwrittenpermissionofJIELI. AMUX0L：AnalogChannel0Left; PLNK_SCLK：PLNKSerialClock； UART1_CTS：Uart1Cleartosend； ADC2：ADCInputChannel3; PWM5：Timer5PWMOutput； UART2TXA：Uart1DataOutput(D)； 7PA2I/O24/8GPIO SD0CLKC：SD0Clock(C); MIC_BIAS：MicrophoneBiasOutput CAP3：Timer3Capture; 8 PA1I/O24/8GPIO ADC1 ： ADCInputChannel1; PWM4 ： Timer4PWMOutput ； UART1RXC ： Uart0DataIn(C); MICI/MIC ： MICInputChannel; 9PA0I/O/ SDPG ： SDPowerSupply ADC0 ： ADCInputChannel0; CLKOUT0 UART1TXC ： Uart1DataOutput(C) ； 10DACVSSP/DACGround 11VCOM/ 12DACLO/DACLeftChannel 13PB7I/O24/8GPIO SD0CLKF ： SD0Clock(F) AMUX1R ： AnalogChannel1Right; SPI2DOA ： SPI2DataOut(A); IIC_SDA_C ： IICDAT(C); ADC9 ： ADCInputChannel9; PWM5 ： Timer5PWMOutput ； UART1RXA ： Uart1DataIn(A); 14PB6I/O24/8GPIO SD0CMDF：SD0Command(F); AMUX1L：AnalogChannel1Left; SPI2CLKA：SPI2DataOut(A); IIC_SCL_C：IICSCL(C); ADC8：ADCInputChannel8; TMR3：Timer3ClockInput; UART1TXA：Uart1DataOut(A); 15PB4I/O24/8GPIO SD0DAT0F：SD0Data0(F); SPI0_DAT2A(2)：SPI0Data2Out_A(2); ADC7：ADCInputChannel7; CLKOUT1 UART2TXC：Uart2DataOut(C); UART2RXC：Uart2DataIn(C); 16 LDO_INP/BatteryChargerIn PB5I/O8GPIOSPI2DIA：SPI2DataInput(A)； AC6965EDatasheet 6 Confidential TheinformationcontainedhereinistheexclusivepropertyofJIELIandshallnotbedistributed,reproduced,ordisclosedinwholeorinpartwithout priorwrittenpermissionofJIELI. (HighVoltage Resistance) PWM3：Timer3PWMOutput； CAP1：Timer1Capture; UART0TXC：Uart0DataOut(C)； UART0RXC：Uart0DataIn(C); 17VBATP/BatteryPowerSupply 18VDDIOP/IOPower3.3v 19PB1I/O24/8 GPIO (pullup) LongPressReset； ADC5：ADCInputChannel5; TMR2：Timer2ClockInput; UART0RXB：Uart0DataIn(B); 20VSSIOP/Ground 21FMIPI/FMAntenna 22BT_RF//BTAntenna 23BT_SOCII/BTOSCIn 24BT_SOCOO/BTOSCOut AC6965EDatasheet 7 Confidential TheinformationcontainedhereinistheexclusivepropertyofJIELIandshallnotbedistributed,reproduced,ordisclosedinwholeorinpartwithout priorwrittenpermissionofJIELI. 2、ElectricalCharacteristics 2.1AbsoluteMaximumRatings Table2-1 SymbolParameterMinMaxUnit TambAmbientTemperature-20+70°C TstgStoragetemperature-65+150°C VBATSupplyVoltage2.25.5V V 3.3IO 3.3VIOInputVoltage-0.3VDDIO+0.3V LDO_INChargeInputVoltage-0.35.5V 2.2PMUCharacteristics Table2-2 S…

Text truncated - open the document above for the full version.

FCC ID: 2BTY9-SP01 Page 1 / 2 APPENDIX 1 PHOTOS OF TEST SETUP Radiated Spurious Emission, Below 1GHz Radiated Spurious Emission, Above 1GHz FCC ID: 2BTY9-SP01 Page 2 / 2 Conducted Emission