2BUNJ-P8-10000Power bank

FCC Warming: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Local Representative Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(7), of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC IDModel name 2BUNJ-P8-10000P8-10000 We hereby acknowledge as follows: i.both signees confirm that the point of contact accepts responsibility to act as a US- American Representative on behalf of the applicant ii.the point of contact provides the physical U.S. address and email as listed below iii.both parties maintain the requirements of this agreement for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. iv.An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. US-American Point of ContactApplicant/Approval Holder Signature Date: 2026-08-17 Signature Date: 2026-08-17 Company Name:GLOCERTS TECHNOLOGY INCShenzhen Xianyang Innovation Technology Co.,Ltd FRN:00363397370038615746 Contact Name:Huiying FanDianming Shen Address:19784 SUNKISSED RIDGE DR, RIVERSIDE, CA 92507 Room302, Building 8, Yunliintelligent park, No. 7, ChangfaLonggang District, Shenzhen, China Phone:(626) 588-803918165740680 Email:[email protected]@126.com

Page 1 of 3 FCC ID: 2BUNJ-P8-10000 External photos Page 2 of 3 FCC ID: 2BUNJ-P8-10000 Page 3 of 3 FCC ID: 2BUNJ-P8-10000

Label FCC ID: 2BUNJ-P8-10000

Page 1 of 4 FCC ID: 2A2NS-GY-Q741 Internal photos Page 2 of 4 FCC ID: 2A2NS-GY-Q741 Page 3 of 4 FCC ID: 2A2NS-GY-Q741 Watch ANT Page 4 of 4 FCC ID: 2A2NS-GY-Q741 Phone ANT

Page 1 of 20 Report No.: AiTDG-260723002W2 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Dongguan Yaxu (AiT) Technology Limited. If there is a need to alter or revise this document, the right belongs to Dongguan Yaxu (AiT) Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. TEST REPORT Product Name:Power bank Brand Name:RORRY Model:P8-10000 Series Model:N/A FCC ID:2BUNJ-P8-10000 Applicant:Shenzhen Xianyang Innovation Technology Co.,Ltd Address:Room302, Building 8, Yunliintelligent park, No. 7, ChangfaLonggang District, Shenzhen, China Manufacturer:Shenzhen Xianyang Innovation Technology Co.,Ltd Address:Room302, Building 8, Yunliintelligent park, No. 7, ChangfaLonggang District, Shenzhen, China Standard(s): FCC CFR 47 PART 1, § 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Date of Receipt:Jul 23, 2026 Date of Test:Jul 23, 2026~ Jul 29, 2026 Issued Date:Aug 17, 2026 Issued By: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China Tel.: +86-769-8202 0499 Fax.: +86-769-8202 0495 Reviewed by: Approved by: Emiya Lin Simba Huang Page 2 of 20 Report No.: AiTDG-260723002W2 Report Revise Record Report VersionIssued DateNotes M0Aug 17, 2026Initial Release Page 3 of 20 Report No.: AiTDG-260723002W2 Contents 1GENERAL INFORMATION ........................................................................................................................................4 1.1ENVIRONMENTAL CONDITIONS........................................................................................................................................4 1.2GENERAL DESCRIPTION OF EUT ......................................................................................................................................4 1.3TEST FACILITY..............................................................................................................................................................5 1.4MEASUREMENT UNCERTAINTY........................................................................................................................................5 2.1DESCRIPTION OF THE TEST MODE.....................................................................................................................................6 2.2SPECIAL ACCESSORIES...................................................................................................................................................6 2.3TEST INSTRUMENTS LIST................................................................................................................................................7 2.3.1Calibration Information ......................................................................................................................................7 2.3.2MAGPy probe information ..................................................................................................................................7 3TEST CONDITIONS AND RESULTS.............................................................................................................................8 3.1APPLICABLE STANDARD.................................................................................................................................................8 3.2LIMIT.........................................................................................................................................................................8 3.3TEST SETUP.................................................................................................................................................................8 3.4MEASUREMENT PROCEDURE..........................................................................................................................................9 3.5TEST RESULT OF E AND H FIELD STRENGTH......................................................................................................................10 3.5.1Duty Cycle .........................................................................................................................................................10 3.5.2For mobile exposure condition:.........................................................................................................................11 3.5.3For portable exposure condition: ......................................................................................................................13 3.6EQUIPMENT APPROVAL CONSIDERATIONS.......................................................................................................................17 3.7CONCLUSION.............................................................................................................................................................17 4TEST SETUP PHOTOGRAPHS OF EUT ......................................................................................................................18 Page 4 of 20 Report No.: AiTDG-260723002W2 1 GENERAL INFORMATION 1.1 Environmental conditions During the measurement the environmental conditions were within the listed ranges: Normal Temperature:25°C Relative Humidity:55 % Air Pressure:101 kPa 1.2 General Description of EUT Product Name:POWER BANK Model/Type reference:P8-10000 Serial Model:N/A Power Supply: Battery Capacity: 10000mAh, 3.85V/38.5Wh Rated Capacity: 6000mAh(5V 3A) USB-C1/USB-C2 Cable Input:5V 3A, 9V2A, 12V1.5A (18W Max) USB-C1/USB-C2 Cable Output:5V 3A,9V2.22A,12V 1.67A, 10V 2.25A …

Text truncated - open the document above for the full version.

Page 1 of 28 Report No.: AiTDG-260723002W1 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Dongguan Yaxu (AiT) Technology Limited. If there is a need to alter or revise this document, the right belongs to Dongguan Yaxu (AiT) Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. TEST REPORT Product Name:Power bank Brand Name:RORRY Model:P8-10000 Series Model:N/A FCC ID:2BUNJ-P8-10000 Applicant:Shenzhen Xianyang Innovation Technology Co.,Ltd Address:Room302, Building 8, Yunliintelligent park, No. 7, ChangfaLonggang District, Shenzhen, China Manufacturer:Shenzhen Xianyang Innovation Technology Co.,Ltd Address:Room302, Building 8, Yunliintelligent park, No. 7, ChangfaLonggang District, Shenzhen, China Standard(s):FCC CFR Title 47 Part 15 Subpart C Date of Receipt:Jul 23, 2026 Date of Test:Jul 23, 2026~ Jul 29, 2026 Issued Date:Aug 17, 2026 Issued By: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China Tel.: +86-769-8202 0499 Fax.: +86-769-8202 0495 Reviewed by: Approved by: Emiya Lin Simba Huang Page 2 of 28 Report No.: AiTDG-260723002W1 Report Revise Record Report VersionIssued DateNotes M0Aug 17, 2026Initial Release Page 3 of 28 Report No.: AiTDG-260723002W1 Contents 1TEST SUMMARY......................................................................................................................................................4 1.1TEST STANDARDS.........................................................................................................................................................4 1.2TEST SUMMARY...........................................................................................................................................................4 1.3TEST FACILITY..............................................................................................................................................................5 1.4MEASUREMENT UNCERTAINTY........................................................................................................................................5 2GENERAL INFORMATION........................................................................................................................................6 2.1ENVIRONMENTAL CONDITIONS........................................................................................................................................6 2.2GENERAL DESCRIPTION OF EUT......................................................................................................................................6 2.3DESCRIPTION OF THE TEST MODE.....................................................................................................................................7 2.4SPECIAL ACCESSORIES...................................................................................................................................................7 2.5EQUIPMENT LIST FOR THE TEST.......................................................................................................................................8 3TEST CONDITIONS AND RESULTS.............................................................................................................................9 3.1CONDUCTED EMISSIONS TEST.........................................................................................................................................9 3.2RADIATED EMISSIONS.................................................................................................................................................12 3.320DB BANDWIDTH....................................................................................................................................................18 3.4ANTENNA REQUIREMENT.............................................................................................................................................20 4TEST SETUP PHOTOGRAPHS OF EUT......................................................................................................................21 5PHOTOS OF THE EUT.............................................................................................................................................22 Page 4 of 28 Report No.: AiTDG-260723002W1 1TEST SUMMARY 1.1Test Standards The tests were performed according to following standards: FCC Rules Part 15.207,15.209, 15.215(c) ANSI C63.10: 2020: American National Standard for Testing Unlicensed Wireless Devices 1.2Test Summary Test ItemSection in CFR 47Test Result Electric Field Radiated EmissionsFCC Part 15 C (Section15.209)PASS 20dB Bandwidth/99% BandwidthFCC Part 15 C (Section15.215(c))PASS AC Power Line Conducted EmissionFCC Part 15 C (Section15.207)PASS Antenna RequirementFCC Part 15 C (Section15.203PASS Page 5 of 28 Report No.: AiTDG-260723002W1 1.3Test Facility Test Laboratory: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China The test facility is recognized, certified or accredited by the following organizations: CNAS-Registration No: L6177 Dongguan Yaxu (AiT) technology Limited is accredited to ISO/IEC 17025:2017 general Requirements for the competence of testing and calibration laboratories (CNAS-CL01 Accreditation Criteria for the competence of testing and calibration laboratories) on April 18, 2022 FCC-Registration No.: 703111 Designation Number: CN1313 Dongguan Yaxu (AiT) Technology Limited has been reg…

Text truncated - open the document above for the full version.

深圳市宸兴电子技术有限公司 产 品 承 认 书 PRODUCT SPECIFICATION FOR APPROVAL 客 户 名 称： CUSTOMER 富登 产 品 名 称： PRODUCT NAME 超薄发射线圈 物 料 编 码： PART No. 4020000000048 产 品 规 格： PRODUCT SPEC 感量规格：6.3uH-6.8uH 线材规格：0.08*56*10Ts（20.5mm） 磁片规格：43.5*5.3*0.5mm双槽 出线长度：40mm双槽出线压合 8mm高温胶带/普通双面胶 日期： DATE 2026 年 07 月 18 日 版 本 型 号： VERSION REV 1.0 供应商确认 Supplier Approve 制定/PREPARED BY审核/CHECKED BY核准/APPROVED BY 李小云周小菊 附上的是产品规格书，有任何疑问，请及时反馈给我们，谢谢! 薛磊 第 1 页 公司名称：深圳市宸兴电子技术有限公司 Shenzhen Chenxing Electronic Technology Co., Ltd. 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 5th Floor, Building 1, Xinkecheng Technology Industrial Park, No. 51 Dabao Road, Xin'an Subdistrict, Bao'an District, Shenzhen 深圳市宸兴电子技术有限公司 版本变更履历 Version Change History 版本记录 Revision 变更前 Before change 变更后 After change 变更日期 Date 批准 Approval by REV 1.02026.07.18薛 磊 第 2 页 公司名称：深圳市宸兴电子技术有限公司 Shenzhen Chenxing Electronic Technology Co., Ltd. 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 5th Floor, Building 1, Xinkecheng Technology Industrial Park, No. 51 Dabao Road, Xin'an Subdistrict, Bao'an District, Shenzhen 深圳市宸兴电子技术有限公司 产 品 规 格 SPECIFICATION 一、磁片尺寸-43.5*5.3*0.5mm 双槽 二、线圈尺寸规格 Dimension specification 线圈外径 B39±1.5mm 线圈内径 C20.5±0.5mm 出线长度 E40mm 锡头长度2-4mm 胶带宽度3mm 周边厚度 D小于 1.45mm 折线处厚度小于 1.7mm *A 43.2±0.4mm *B 5.3±0.3mm 磁片厚度 0.5±0.05mm E 7±0.3mm 第 3 页 公司名称：深圳市宸兴电子技术有限公司 Shenzhen Chenxing Electronic Technology Co., Ltd. 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 5th Floor, Building 1, Xinkecheng Technology Industrial Park, No. 51 Dabao Road, Xin'an Subdistrict, Bao'an District, Shenzhen Operation Frequency100-500KHz Antenna TypeLoop coil antenna Antenna gain:0dBi We statement that All measurements were performed radiated and therefore additional antenna gain documentation is not required. 深圳市宸兴电子技术有限公司 三、原理图Schematiccharacter 四、绕线参数Coilspecification 端子 TERMINAL 线径 WIRE 圈数 Turns 绕线方向 WindingDirection SF漆包线 0.08*56 股10TsCCW 五、电气特性Electroniccharacter 温度TEMPERATURE:25±10 °C,湿度RELATIVEHUMIDITY:65±20% 项目 ITEM 标准 SPECIFICATION 测试条件 TEST FREQUENCY 测试仪器 TEST EQUIPMENTS L 6.3uH-6.8uH 100KHz/1.0VVICTOR4092D Q 大于 48 100KHz/1.0VVICTOR4092D 六、环境特性Environmentcharacter 项目 ITEM 标准 SPECIFICATION 工作温度和湿度 OperatingTemperatureand Humidity -30°C-80°C/30%-90% 存储温度和湿度 StorageTemperatureand Humidity -40°C-90°C/30%-90% 第 4 页 公司名称：深圳市宸兴电子技术有限公司 Shenzhen Chenxing Electronic Technology Co., Ltd. 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 5th Floor, Building 1, Xinkecheng Technology Industrial Park, No. 51 Dabao Road, Xin'an Subdistrict, Bao'an District, Shenzhen 深圳市宸兴电子技术有限公司 第 5 页 七、产品图片 公司名称：深圳市宸兴电子技术有限公司 Shenzhen Chenxing Electronic Technology Co., Ltd. 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 5th Floor, Building 1, Xinkecheng Technology Industrial Park, No. 51 Dabao Road, Xin'an Subdistrict, Bao'an District, Shenzhen

SPECIFICATION SHEET Guangdong Changrong Intelligent Technology Co., Ltd. G25-2.3-4.0UH-3200GS-20MM December 18th, 2025 CUSTOMER: Customer Part No.: Our Model No.: Sample Date: Supplier: Dongguan Yuyao Electronic Technology Co., Ltd. Drawn ByReviewed ByApproved By Liu NianjiaoCao HanqingCao Qiancheng Dongguan Yuyao Electronic Technology Co., Ltd. Tel: ____________________ 13717089408 Fax: ____________________ Address: 3rd Floor Warehouse, Building 21, Xintaiyang Industrial City, Lincun, Tangxia Town, Dongguan Customer Name Customer Part No. Our Model No.Version Date ChangrongG25-2.3-4.0UH-3200GS-20MM A02025.12.18 1. Plan View Drawing (Unit: MM) I L F G J H K A C 磁铁 1 2 1 2 A B C D E F H I J 7.5±0.1 2.0±0.1 2.0±1 14±0.2 20.5±0.5 24.7±0.2 23.0±0.2 21±0.2 7.6±0.1 K B D E L M G 13.5±0.2 2.3±0.15 20±1 2.15±0.1中柱高度 M 2. Product Parameters 3. Technical Requirements PinWire DiameterTurnsRemarks 1-20.08 × 48P9THot-air stranded wire Secure the lead start and end to prevent loosening or wire breakage. Cut excessively long leads per customer requirement and tin them; the tinning depth shall be uniformly 2 ± 1 MM. Apply an appropriate amount of white glue on the magnetic sheet and attach the coil; the product surface must be kept clean and tidy throughout the process. The hard magnetic sheet used shall have a round hole and be free of damage. Additional process (per customer requirement): Install a 7.5 × 2.0 MM magnet into the center round hole of the finished product, apply a 14 MM diameter round double-sided adhesive tape on the back of the finished product, then package. 1. 2. 3. 4. 5. Operation Frequency300-500KHz Antenna TypeLoop coil antenna Antenna gain:0dBi We statement that All measurements were performed radiated and therefore additional antenna gain documentation is not required. 4. Electrical Parameters 1. Inductance & Q Value: PIN 1 - 2 = 4.0 uH ± 0.3 UH Q Value ≥ 25 The above inductance and Q value are measured with a Quan Hua 1062A instrument at 100 KHZ / 1.0 Vrms as the standard, or an equivalent instrument. 5. Bill of Materials No.NameMaterial / SpecSupplierRemarks 1 Hot-air stranded wire 0.08 × 48P Weihan or equivalent 2Magnetic sheetG25 hard substrate Tiantong or equivalent 3Tin High-temperature eco- friendly Qiandao or equivalent 4White glueBY882 Baoyue or equivalent 5Magnet7.5 × 2.0 × 3200 ± 100 GS 6Back adhesive513-14MMRound

Page 1 of 1 FCC ID: 2BUNJ-P8-10000