A3LBTM730BBT audio module

Modular installation manual WARNING i. We recommend to keep 20cm distance when installing this module. ii. This module should not be installed and operating simultaneously with other radio without additional evaluation or FCC filing. iii. The host system should have proper label showing that it "Contains FCC ID : A3LBTM730B" Version 1.0 Samsung Electronics page 1 of 6 User Manual for BTM730B (for AIO PC) 1. Introduction BTM730B BT Module containing Bluetooth 3.0 / Mac compatible Bluetooth Module/ Baseband optimized Radio with UART interface. 2. Hardware Configuration 2.1 Main Chipset Information Item IC Vendor Part Number Bluetooth 3.0 MAC/Baseband/Radio CSR BC05MM 2.2 Block Diagram Block Diagram of BT Module is as Figure.1. Figure.1 BTM730B Block Diagram Version 1.0 Samsung Electronics page 2 of 6 3. Operational Description BTM730B BT Module is RF communication controller which is equipped with AIO PC for the users who use wireless devices. A number of channels are 79 which are based on IEEE 802.15.1/1a and frequency range is 2402MHz ~ 2480MHz. Each channel has a bandwidth of 1 MHz. - Transmitter Baseband processor uses FFHS (Frequency Hopping Spread Spectrum) scheme to avoid interference from other signals by hopping to a new frequency after transmitting or receiving a packet. BTM740B BT Module provides 1Mbps, 2Mbps (EDR), 3Mbps (EDR) data rate and 2FSK/DQPSK/8DPSK modulation. Tx signal is modulated as Tx IQ by DAC (Digital-Analog Convertor) inside of baseband IC then it is transmitted through internal PA (Power Amplifier). - Receiver Transceiver IC is insulated by Low Noise Amplifier (LNA) to avoid undesirable noise interferences. RF signal is converted and demodulated as RX IQ by through intermediate frequency and RF filter then it is input to the processing unit. - Power Class BTM730B BT Module operate as BT Power Class 1 of IEEE 802.15.1/1a Standard. - Interface BTM730B BT Module supports standard UART interface and UART setting values are as Table.1. Table.1 UART Setting Version 1.0 Samsung Electronics page 3 of 6 - RF Specifications RF specifications are as Table.2. Parameter Min Typ. Max Unit RF Characteristics RF Frequency Range 2.402 - 2.480 GHz Output power 0 6.5 20 dBm TX Spurious Emission 30.0MHz to 1.0GHz 1.0GHz to 12.5GHz 1.8GHz to 1.9GHz 5.15GHz to 5.3GHz - - -30 dBm TX Frequency Tolerance -75 - 75 KHz Carrier Frequency Drift -20 - 20 KHz TX Output Spectrum 20dB bandwidth - - 1 MHz Modulation Characteristics Delta F1 140 - 175 KHz Delta F2 115 - - KHz Delta F2 / F1 0.8 - 3 - Receiver sensitivity BER at -70dBm - - 0.1 % Maximum Input Level BER at -20dBm - - 0.1 % RX Spurious Emission 30.0MHz to 1.0GHz 1.0GHz to 12.5GHz 1.8GHz to 1.9GHz 5.15GHz to 5.3GHz - - -54 dBm Table.2 RF Specifications Version 1.0 Samsung Electronics page 4 of 6 4. Pin Description Pin descriptions are as Table.3. Table.3 Pin Description Version 1.0 Samsung Electronics page 5 of 6 5. Detail Specifications - Frequency : 2402~2480 MHz - Number of Channel : 79ch - Oscillation : VCO - Operating Voltage : TYP. DC 3.3 V (Operating Range : 3.1V~3.6V) - Current Consumption : Max.100mA - Dimension : 22 mm X 26 mm X 2.5 mm - Weight : 2.5g - Operating Temperature : -10°C ~ +50°C - Communication : Semi-Duplex Operation - Modulation : 2FSK, pi/4 DQPSK, 8DPSK - Label Location of Module: - Host system labeling instruction : We add following statement at label of each host. "The product was mounted with a Bluetooth module (FCC ID: A3LBTM730B) which was certificated by FCC Part 15 Subpart C 15.247." * T his wireless device may cause propagation interferences so can’t available for life-saving services. This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 ㎝ must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. This device complies with part 15 of th e F CC Rules. Operation is s ubject to the f ollowing two c onditions: (1) This devi ce may not cause harmful interference, and (2) This devi ce must accept an y i nterference received, including interference that may cau se undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for c ompliance could void user’s authority to operate the e quipment. Version 1.0 Samsung Electronics page 6 of 6 * Please use only allowed PIFA antenna below. * Use other antenna may subject to additional testing and filing to FCC.

SCS-F26 Modular Approval Letter Page 1 of 2 Rev 8.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Modular Approval Declaration Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (Obsolete) 1.0 1.0 Dec-04-2006 Added IC Modular Letter (Obsolete) 1.0 2.0 Feb 16 2009 Add LMA and MA option (Obsolete) 2.0 3.0 April 14 2010 Revised per RSS Gen issue 3.0 (Obsolete) 3.0 4.0 Jan 12 2011 Removed Foot(2) (obsolete) 4.0 5.0 July 19 2011 Adding New note per KDB996369 D01 V01R03 (obsolete) 5.0 6.0 August 29 2011 Updated company template & Added text box (obsolete) 6.0 7.0 Jan-31-2012 Updated modular requirement (current) 7.0 8.0 Sept 05 2014 SCS-F26 Modular Approval Letter Page 2 of 2 Rev 8.0 Samsung Electronics Co., Ltd. 19 Chapin Rd., Building D, Pine Brook, New Jersey, United States, 07058 Tel. +1-973-808-6362 / Fax. +1-973-808-6361 (Date) 11/17/2014 (Wireless Full Module) FCC ID : A3LBTM730B , is seeking FCC Authorization as a Single Modular transmitter / Single Limited Modular Approval (Please check one). The EUT meets the requirements for Single Modular approval / Single Limited Modular Approval (please check one) as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below: Questions are: * Please provide a detailed explanation if the answer is “No.” Item Modular requirement Yes No 1 The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly; √ 2 The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; √ 3 The module must contain power supply regulation on the module; √ 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); √ 5 The module must demonstrate compliance in a stand-alone configuration; √ 6 The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); √ 7 The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; √ 8 The module must comply with RF exposure requirements √ Note: (1) LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured. (2) Please provide Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device. (3) For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, technical description of how such control is implemented to ensure prevention of third party modification must be provided (see KDB 594280). Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. John SC LEE / Manager Samsung Electronics Co., Ltd.

Samsung Electronics Co., Ltd. 19 Chapin Rd., Building D, Pine Brook, New Jersey, United States, 07058 Tel. +1-973-808-6362 / Fax. +1-973-808-6361 Date: November 17, 2014 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, Samsung Electronics Co., Ltd., hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project : - Product: BT audio module - Model name: BTM730B - FCC ID: A3LBTM730B We affirm that between SIEMIC and Samsung Electronics Co., Ltd., any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This authorization is valid until further written notice from the applicant. Sincerely Yours, ______________________________________ John SC LEE /Manager /Samsung Electronics Co., Ltd.

Samsung Electronics Co., Ltd. 19 Chapin Rd., Building D, Pine Brook, New Jersey, United States, 07058 Tel. +1-973-808-6362 / Fax. +1-973-808-6361 FCC Confidentiality Request Letter Date: November 17, 2014 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia MD 21046 Subject: Permanent Confidentiality Request for FCC ID: A3LBTM730B We hereby request confidential treatment of information accompanying this application as outlined below: • Block diagram • Schematics • Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely Yours, ______________________________________ John SC LEE /Manager /Samsung Electronics Co., Ltd.

http://www.emc2000.co.kr EMC compliance Ltd. Page: 1 of 1 65, Sinwon-ro, Yeongtong-gu, Suwon- si, Gyeonggi-do, 443-390, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. External photos of EUT

제품 Label : WSBTM730B00 ( BC5MM ) 2014. 11. 13 SEC Code 채번 완 료 제품 () 채번 완 19mm Samsung Electronics Co., Ltd. V.1 MSIP-CRM-SEC-XXXXXXXFCC ID: A3LBTM730BCMIIT ID: 201XXXXXXX mm CMIIT ID: 201XXXXXXX 19mm Made in Korea 15m V0102 Model:BTM730B4709-002340WSBTM730B00BAAKD7301 15mm

http://www.emc2000.co.kr EMC compliance Ltd. Page: 1 of 1 65, Sinwon-ro, Yeongtong-gu, Suwon- si, Gyeonggi-do, 443-390, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. Internal photos of EUT

http://www.emc2000.co.kr EMC compliance Ltd. Page: 1 of 1 480-5, Sin-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. * RF Exposure 1. Regulation According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this Chapter. Limits for Maximum Permissive Exposure: RF exposure is calculated. Frequency Range Electric Field Strength [V/m] Magnetic Field Strength [A/m] Power Density [㎽/㎠] Av er ag ing Time [minute] Limits for General Population / Uncontrolled Exposure 0.3 ~ 1.34 614 1.63 *(100) 30 1.34 ~ 30 824 /f 2.19/f *(180/f 2 ) 30 30 ~ 300 27.5 0.073 0.2 30 300 ~ 1500 / / f/1500 30 1500 ~ 15000 / / 1.0 30 f=frequency in ㎒, *= plane-wave equivalent power density MPE (Maximum Permissive Exposure) Prediction Predication of MPE limit at a given distance: Equation from page 18 of OET Bulletin 65, Edition 97-01  SPGRRPGS4 4 2  S=power density [㎽/㎠] P=Power input to antenna [㎽] G=Power gain of the antenna in the direction of interest relative to an isotropic radiator R= distance to the center of radiation of the antenna [㎝] EUT: Maximum peak output power = 6.68 [㎽](= 8.25 ㏈m) Antenna gain= 4.70 (= 6.72 [㏈i]) 100 ㎽, at 20 cm from an antenna 6 [㏈i] S = PG/4πR² = 100 × 3.98 / (4 × π × 400) = 0.079 18 [㎽/㎠] < 1.0 [㎽/㎠] 6.68 ㎽, at 20 cm from an antenna 6.72 [㏈i] S = PG/4πR²= 0.006 25 [㎽/㎠] < 1.0 [㎽/㎠] 6.68 ㎽, at 2.5 cm from an antenna 6.72 [㏈i] S = PG/4πR²= 0.399 86 [㎽/㎠] < 1.0 [㎽/㎠] 2. RF Exposure Compliance Issue The information should be included in the user’s manual: This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 ㎝ must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements.

http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0191 EMC compliance Ltd. Page: 2 of 48 480-5, Sin-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. [ Contents ] 1. Client information .................................................................................................. 3 2. Laboratory information ........................................................................................... 4 3. Description of E.U.T. ............................................................................................... 5 3.1 Basic description .............................................................................................. 5 3.2 General description ............................................................................................ 5 3.3 Test frequency ................................................................................................. 6 3.4 Test Voltage .................................................................................................... 6 4. Summary of test results ............................................................................................ 7 4.1 Standards & results ............................................................................................ 7 4.2 Uncertainty..................................................................................................... 7 5. Test results .......................................................................................................... 8 5.1 Antenna Requirement ......................................................................................... 8 5.2 Maximum Peak Output Power ................................................................................ 9 5.3 Carrier Frequency Separation ............................................................................... 14 5.4 20 dB Channel Bandwidth .................................................................................. 19 5.5 Number of Hopping Channels .............................................................................. 27 5.6 Time of Occupancy(Dwell Time) ........................................................................... 31 5.7 Spurious Emission, Band edge and Restricted bands ...................................................... 36 5.8 Con ducted Emission ......................................................................................... 47 6. Test equipment used for test .................................................................................... 48 http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0191 EMC compliance Ltd. Page: 3 of 48 480-5, Sin-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. 1. Client information Applicant: Samsung Electronics Co., Ltd. Address: 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 443-742 Telephone number: +82-31-277-6255 Facsimile number: +82-31-277-5231 Contact person: Rho Sang Soo / [email protected] Manufacturer: Samsung Electronics Co., Ltd. Address: 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 443-742 http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0191 EMC compliance Ltd. Page: 4 of 48 480-5, Sin-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. 2. Laboratory information Address EMC compliance Ltd. 480-5, Sin-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea Telephone Number: 82-31-336-9919 Facsimile Number: 82-505-299-8311 Certificate KOLAS No.: 231 FCC Site Designation No.: 687132 FCC Site Registration No.: KR0040 VCCI Site Registration No.: R-3327, G-198, C-3706, T-1849 IC Site Registration No.:8035A-2 SITE MAP EMC Compliance Ltd. Suwon city http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0191 EMC compliance Ltd. Page: 5 of 48 480-5, Sin-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. 3. Description of E.U.T. 3.1 Basic description Applicant: Samsung Electronics Co., Ltd. Address of Applicant 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 443-742 Manufacturer Samsung Electronics Co., Ltd. Address of Manufacturer 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 443-742 Type of equipment BT audio module Basic Model BTM730B Serial number N/A 3.2 General description Frequency Range 2 402 ㎒ ~ 2 480 ㎒ Type of Modulation GFSK, 8DPSK Number of Channels 79 channels Type of Antenna PIFA Antenna Antenna Gain 6.72 ㏈i Transmit Power 8.25 ㏈m Power supply DC 3.3 V* * Declared by the applicant. http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0191 EMC compliance Ltd. Page: 6 of 48 480-5, Sin-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. 3.3 Test frequency Frequency Low frequency 2 402 ㎒ Middle frequency 2 441 ㎒ High frequency 2 480 ㎒ 3.4 Test Voltage mode Voltage Norminal voltage DC 3.3 V ※ 15.247 Requirements for Bluetooth transmitter  This Bluetooth module has been tested by a Bluetooth Qualification Lab, and we confirm the following: 1) This system is hopping pseudo-randomly. 2) Each frequency is used equally on the average by each transmitter. 3) The receiver input bandwidths that match the hopping channel bandwidths of their corresponding transmitters 4) The receiver shifts frequencies in synchronization with the transmitted signals.  15.247(g): The system, consisting of both the transmitter and the receiver, must be designed to comply with all of the regulations…

Text truncated - open the document above for the full version.

http://www.emc2000.co.kr EMC compliance Ltd. Page: 1 of 3 65, Sinwon-ro, Yeongtong-gu, Suwon- si, Gyeonggi-do, 443-390, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. Te s t setup photos * 9 ㎑ ~ 30 ㎒ * 30 ㎒ ~ 1 ㎓ http://www.emc2000.co.kr EMC compliance Ltd. Page: 2 of 3 65, Sinwon-ro, Yeongtong-gu, Suwon- si, Gyeonggi-do, 443-390, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. * 1 ㎓ Over http://www.emc2000.co.kr EMC compliance Ltd. Page: 3 of 3 65, Sinwon-ro, Yeongtong-gu, Suwon- si, Gyeonggi-do, 443-390, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced except in full, Without the written approval. * Conduction