A3LML-NWA65L2.4 GHz WLAN Module

User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 1/21 User Manual ML-NWA65L(ML-NWA65L/XRX) 802.11b/g/n WLAN Module July, 2010 User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 2/21 Revision History Revision Date Descriptions 0.1 2010-07-30 Created User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 3/21 Table of Contents REVISION HISTORY .................................................................................................................. 2 1 GENERAL DESCRIPTION ..................................................................................................... 4 1.1 F UNCTIONAL DESCRIPTION .......................................................................................................... 4 1.2 F EATURES ............................................................................................................................... 4 1.3 A PPLICATIONS .......................................................................................................................... 4 1.4 D IMENSION AND PIN ASSIGNMENTS ............................................................................................... 5 2 OPERATING CONDITIONS .................................................................................................. 7 2.1 M AXIMUM POWER SUPPLY RATING ................................................................................................ 7 2.2 C ONNECTION TO HOST ............................................................................................................. 7 2.3 G ROUND CONNECTION ............................................................................................................... 7 2.4 S TORAGE CONDITION ................................................................................................................ 7 2.5 A BSOLUTE MAXIMUM RATINGS ..................................................................................................... 8 2.6 C URRENT CONSUMPTION ............................................................................................................ 8 3 RF SPECIFICATION ............................................................................................................ 9 3.1 S UPPORTABLE MODULATION SCHEME & DATA RATES ......................................................................... 9 3.2 C HANNEL & CENTER FREQUENCY ................................................................................................ 10 3.3 ANTENNA SPECIFICATIONS ...................................................................................................... 11 User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 4/21 1 General Description 1.1 Functional Description ML-NWA65L(ML-NWA65L/XRX) is the low power USB 2.0 module for 802.11b/g/n wireless LAN (WLAN) aimed at embedded applications. ML-NWA65L(ML-NWA65L/XRX) is the USB 2.0 module that adopts a single-chip wireless local area network (WLAN) medium-access controller (MAC) spread-spectrum baseband processor and 2.4 GHz RF radio. ML-NWA65L(ML-NWA65L/XRX) supports IEEE 802.11b, 802.11g and 802.11n standards. ML-NWA65L(ML-NWA65L/XRX) provides crucial power management functionality and requires only a single 3.3V or 5.0 V supply voltage. Figure 1-1 ML-NWA65L(ML-NWA65L/XRX) Picture 1.2 Features  Wi-Fi compliant  Security: WEP, WPA-PSK, WPA2-PSK, WMM, WMM-PS, TKIP, and AES hardware acceleration  Host interface: USB 2.0  Low power consumption  Single 3.3V or 5.0 V external supply voltage required 1.3 Applications  Network printer servers with WLAN connectivity  Set-top boxes that need WLAN connectivity User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 5/21 1.4 Dimension and Pin Assignments 1.4.1 Mechanical Dimension W X L X H = 45mm X 65mm X 5.1mm Figure 1-2 ML-NWA65L(ML-NWA65L/XRX) Top 45mm 65mm User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 6/21 1.4.2 HOST Interface USB Interface : Molex 53261-0671, 6pin, Right Angle, SMT * SIZE : 5.2 x 12.65 x 3.4 mm Figure 1-3 ML-NWA65L(ML-NWA65L/XRX) CON1 Connector PIN Assignment Table 1-1 CON1 PIN Description No. Pin Name Description 1 Shell Drain wire, to GND 2 VBUS RED, 5V from HOST 3 D- White, USB data Negative 4 D+ Green, USB data Positive 5 GND Black, signal ground 6 Shell Drain wire, to GND User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 7/21 2 Operating Conditions 2.1 Maximum Power Supply Rating The supply Voltage of ML-NWA65L(ML-NWA65L/XRX) is 5V , do follow the Maximum Rating in 3.1. 2.2 Connection to HOST ML-NWA65L(ML-NWA65L/XRX) will work properly only if connecting to USB2.0 Interface as defined at 1.5.2 . 2.3 Ground Connection ML-NWA65L(ML-NWA65L/XRX) does not need special ground, but uses the ground wire in HOST Interface. 2.4 Storage Condition It needs proper condition for protecting the rust. - Temperature : 0 ~ +50 °C - Humidity : lower level recommended , 25% ~ 65%RH - Max Storage Limit : Within 6 Month from Production User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 8/21 2.5 Absolute Maximum Ratings Symbol Parameter Conditions Min. Nom. Max. Unit DC supply DC supply voltage from HOST 3.3V applied +3.1 +3.3 +3.5 V 5V applied +4.85+5.0 +5.25 V DC for I/O USB2.0 Compliant - - - - ESD* Electro-static discharge voltage IEC1000-4~2 POINT: CON1, CON12 AIR 5K V Contact 1K V T S Storage temperature -20 - +85 °C T O Operating temperature 0 - +60 °C * Final specification will be fixed later. 2.6 Current Consumption Symbol Parameter Min. Nom. Max. Unit Current consumption * Transmit current value 11b 290 <500 mA 11g/n 230 <500 mA * It can be different to test condition. User Manual REV 0.1 Samsung Electronics Proprietary and Confidential 9/21 3 RF Specification All measurements are made under nominal power supply and room temperature 25 °C unless specified. RF specification of ML-NWA65L(ML-NWA65L/XRX) was defined according to 802.11b/g mandatory 3.1 …

Text truncated - open the document above for the full version.

Samsung Electronics Co Ltd 18600 Broadwick St. Rancho Dominguez, CA 90220 United States Date: July 14, 2010 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

Samsung Electronics Co Ltd 18600 Broadwick St. Rancho Dominguez, CA 90220 United States Date: July 14, 2010 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA LETTER OF AUTHORIZATION We, the undersigned, hereby authorize Harvey Sung of Digital EMC Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: A3LML-NWA65L including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of Digital EMC Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Samsung Electronics Co Ltd Sincerely, Peter Ra General Manager

Samsung Electronics Co Ltd 18600 Broadwick St. Rancho Dominguez, CA 90220 United States Date: July 14, 2010 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: A3LML-NWA65L To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Samsung Electronics Co Ltd hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give Samsung Electronics Co Ltd temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description File name PERMANENT 1 Block Diagram Block Diagram_A3LML-NWA65L.pdf 2 Operational Description Operational Description_A3LML-NWA65L.pdf 3 Schematics Schematic_A3LML-NWA65L.pdf 4 Part Lists Part List_A3LML-NWA65L.pdf SHORT-TERM 5 External Photos Ext Photo_A3LML-NWA65L.pdf 6 Internal Photos Int Photo_A3LML-NWA65L.pdf 7 Test-Setup Photos Test Photo_A3LML-NWA65L.pdf 8 Users Manual User Manual_A3LML-NWA65L.pdf Note: The pictures on the label location do not require any long term or short term confidentiality. The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Peter Ra General Manager

Samsung Electronics Co Ltd 18600 Broadwick St. Rancho Dominguez, CA 90220 United States Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA July 14, 2010 Modular Approval Attestation for Wireless Lan. Applicant: Samsung Electronics Co Ltd FCC ID: A3LML-NWA65L No. FCC requirements 1 Have its own RF shielding RF Block shielded by Metal Case 2 Have buffered modulation/data inputs (if such inputs are provided), Yes, the module has buffered data input. 3 The modular transmitter must have its own power supply regulation. We used self own power supply regulation. 4 Meet the antenna requirements of section 15.203 This module uses chip antenna. This module meets the antenna requirements of section 15.203 5 Be tested in a stand-alone configuration, i.e., the antenna, AC or DC power and data input/output lines must be connected to the module but, the module must not be inside another case during testing Yes, the EUT (module) was tested a stand alone configuration. 6 Be labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The proposed FCC ID label format is to be placed on the module. If FCC ID label is not visible when module is install into the system, “Contains FCC ID: A3LML-NWA65L” shall be placed on the outside of final product. 7 The modular transmitter is manufactured so that the user can not influence the operation of the transmitter that will operate outside of the scope of the regulations. It complies with specific rules or operating requirements. And instruction is included User manual. 8 Address compliance with the Commission`s RF exposure limits in Sections 1.1310 and 2.1093. In addition, spread spectrum transmitters operation under Section 15.247 are required to address RF exposure compliance in accordance with Section 15.247(b)(4) The output power of this device is much lower than the low threshold (60/f mW) of General Population which requires SAR. Sincerely, Peter Ra General Manager

1 Chris Harvey From: 이원정 [[email protected]] Sent: Tuesday, September 07, 2010 2:35 AM To: 'Chris Harvey'; [email protected]; [email protected] Cc: [email protected]; [email protected] Subject: RE: Samsung Electronics Co Ltd , FCC ID: A3LML-NWA65L, Assessment NO.: AN10T0759, Notice#1 Attachments: RSS-102 Annex C_ML-NWA65L.pdf; RSS-102 Annex A_ML-NWA65L.pdf; A3LML- NWA65L.zip RSS-102 Annex _ML-NWA65L.pdf RSS-102 Annex _ML-NWA65L.pdf A3LML-NWA65L.z ip (6 MB) Dear Chris, Thank you for your waiting. I send the revised documents of AN10T0759 project. And I reply to your e-mail. If you have any question and need information, please let me know. And I would be grateful if you could issue the certificate as soon as possible. I am so sorry that I always inquire to issue a certificate ASAP. Have a good day~! Best regards, Will 1. The RF Test report has not been submitted (test setup photos were submitted). It is likely that many of the questions below may be clarified by the submittal of the test report, but I will ask them anyway. Please submit the RF test report. => please check the attached file. 2. The Internal/External photos show a device with a black enclosure, into which the EUT module has been installed, the label location exhibit shows the label on the outside of the black enclosure, but the Operational Description and Manual show just the internal PCB as the device. Please clearly identify the EUT and ensure that the labeling is on the EUT and the EUT was tested in stand-alone configuration as required for modules. => the label is attached on the EUT as label location file. 3. Some documentation shows a 40MHz channel capability, but other documents only show a 20 MHz channel capability. Please confirm the capability of this device (and ensure it was tested for these capabilities). => This device only supports a HT20 of 802.11n. Not HT40. 4. Please confirm if the 2nd antenna is used only for receive diversity. The Block Diagram shows an Antenna Select and DPDT switch. Can either or both antennas transmit? Which antennas were tested? => Simultaneous transmission is not supported. But a transmitting antenna is selected by RX diversity.(They call "TX diversity".) All the test items were performed at Antenna 1 and Antenna 2. And the worst case data were reported in the revised test report. 5. The Users Manual indicates that this module shall be installed with 20 cm separation. Please provide an RF Exposure MPE calculation exhibit for this device showing compliance at the 20 cm minimum separation distance. 2 -----Original Message----- From: Chris Harvey [mailto:[email protected]] On Behalf Of Chris Harvey Sent: Thursday, August 19, 2010 9:13 PM To: [email protected]; [email protected]; '이원정' Cc: [email protected]; [email protected] Subject: RE: Samsung Electronics Co Ltd , FCC ID: A3LML-NWA65L, Assessment NO.: AN10T0759, Notice#1 Will, I just want to be sure you have received this e-mail request for the TCB application as well. I am also finding that the same questions need to be addressed for the Industry Canada application (AN10I3437) as well as the need for the following exhibits: Annex A of RSS-102 Annex C of RSS-102 (RF Exposure Technical Brief - MPE calculations) Please let me know if you have any questions. Best regards, Chris Harvey -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Tuesday, August 17, 2010 9:21 AM To: [email protected] Cc: [email protected]; [email protected] Subject: Samsung Electronics Co Ltd , FCC ID: A3LML-NWA65L, Assessment NO.: AN10T0759, Notice#1 Dear Harvey, You are listed as the Technical Contact for the above referenced TCB application. The following item(s) need(s) to be resolved before the review can be continued: 1. The RF Test report has not been submitted (test setup photos were submitted). It is likely that many of the questions below may be clarified by the submittal of the test report, but I will ask them anyway. Please submit the RF test report. 2. The Internal/External photos show a device with a black enclosure, into which the EUT module has been installed, the label location exhibit shows the label on the outside of the black enclosure, but the Operational Description and Manual show just the internal PCB as the device. Please clearly identify the EUT and ensure that the labeling is on the EUT and the EUT was tested in stand-alone configuration as required for modules. 3. Some documentation shows a 40MHz channel capability, but other documents only show a 20 MHz channel capability. Please confirm the capability of this device (and ensure it was tested for these capabilities). 4. Please confirm if the 2nd antenna is used only for receive diversity. The Block Diagram shows an Antenna Select and DPDT switch. Can either or both antennas transmit? Which antennas were tested? 5. The Users Manual indicates that this module shall be installed with 20 cm separation. Please provide an RF Exposure MPE calculation exhibit for this device showing compliance at the 20 cm minimum separation distance. There is a new feature on the CCS web site for uploading additional exhibits. Please upload the additional/replacement exhibits using this new feature. If there are any questions or problems please contact me directly. The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the 3 original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. Best regards, Chris Harvey [email protected]

FCCID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 1 FCCID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 2 FCCID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 3

FCC ID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase - The FCC label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. - The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the user's manual.

FCCID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 1 FCCID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 2 FCCID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 3 FCCID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. Antenna Information Note: For transmitting, only one antenna is selected following RX diversity. Ant 2 Ant 1 FCCID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 4

Specifications for Approval BUYER Samsung Electronics Co Ltd MODEL ML-NWA65L Frequency Eff. (%) Ave. Gain (dBi) Peak Gain (dBi) Directivity (dBi) 2400 MHz 64-1.932.063.99 2421 MHz 74-1.282.463.74 2442 MHz 76-1.192.463.65 2463 MHz 66-1.811.763.57 2484 MHz 81-0.942.533.47 2500 MHz 59-2.281.173.45 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 0 1000.000.000.00 Model Name : File NameMemo : Sample Version Airlink 3D Antenna Measurement Results -20.00 -15.00 -10.00 -5.00 0.00 5.00 10.00 123456789101112131415161718 dBi 3D Average Gain & Peak Gain Ave. Gain (dBi) Peak Gain (dBi)

CAM350 PRO V 7.0 : Tue May 11 14:57:35 2010 - (Untitled) : comp silk.gbr

-~ - - The MPE calculation for this exposure is shown below. The peak radiated output power (EIRP) is calculated as follows: ▪=+- =+ = - ▪S=- =X = - FCCID: A3LML-NWA65L MPE Calculations(WLAN: 802.11b) Frequency range :2412MHz2462MHz Maximum RF output power :15.15dBm Maximum antenna peak gain :2.46dBi The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the user. EIRPPGNote 15.15dBm2.46dBiP = Power input to the antenna(dBm) 17.61dBmG = Power gain of the antenna(dBi) Power density at the specific separation P G / ( 4 R 2 π ) Note 32.7341.762 / ( 4 X 20 2 X π )S = Maximum power dencity(mW/cm 2 ) 0.01147 mW/cm 2 P = Power input to the antenna(mW) The power desity at 20cm does not exceed the 1.0mW/cm 2 . G = Numeric power gain of the antenna R = Distance to the center of the radiation of the antenna(20cm) Conclusion : The exposure condition of this device is compliant with FCC rules. The maximum permissible exposure(MPE) of the general population/Uncontrolled for this device is 1.0 mW/cm 2 . TRF-RF-206(00)100216 -~ - - The MPE calculation for this exposure is shown below. The peak radiated output power (EIRP) is calculated as follows: ▪=+- =+ = - ▪S=- =X = - FCCID: A3LML-NWA65L MPE Calculations(WLAN: 802.11g) Frequency range :2412MHz2462MHz Maximum RF output power :13.92dBm Maximum antenna peak gain :2.46dBi The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the user. EIRPPGNote 13.92dBm2.46dBiP = Power input to the antenna(dBm) 16.38dBmG = Power gain of the antenna(dBi) Power density at the specific separation P G / ( 4 R 2 π ) Note 24.6601.762 / ( 4 X 20 2 X π )S = Maximum power dencity(mW/cm 2 ) 0.00864 mW/cm 2 P = Power input to the antenna(mW) The power desity at 20cm does not exceed the 1.0mW/cm 2 . G = Numeric power gain of the antenna R = Distance to the center of the radiation of the antenna(20cm) Conclusion : The exposure condition of this device is compliant with FCC rules. The maximum permissible exposure(MPE) of the general population/Uncontrolled for this device is 1.0 mW/cm 2 . TRF-RF-206(00)100216

1006-00229 DRTFCC1008-0154(1) Page 2 / 113 Copyright ○ C 2010, Digital EMC Co., Ltd. CONTENTS 1. Equipment information .............................................................. 3 1.1 Equipment description ............................................................. 3 1.2 Ancillary equipment ................................................................. 3 2. Information about test items ..................................................... 4 2.1 Test mode ................................................................................ 4 2.2 Auxiliary equipment ................................................................. 4 2.3 Tested frequency ..................................................................... 4 2.4 Tested environment ................................................................. 4 2.5 EMI Suppression Device(s)/Modifications ............................... 4 3. Test Report ................................................................................. 5 3.1 Summary of tests .................................................................... 5 3.2 Transmitter requirements ........................................................ 6 3.2.1 6 dB Bandwidth ................................................................... 6 3.2.2 Peak Output Power ........................................................... 13 3.2.3 Out of Band Emissions / Band Edge ................................. 32 3.2.4 Out of band Emission – Radiated ..................................... 69 3.2.5 Transmitter Power Spectral Density .................................. 85 3.2.6 AC Conducted Emissions .................................................. 92 3.2.7 Antenna Requirements ..................................................... 99 3.3 Receiver requirements ........................................................ 100 3.3.1 AC Conducted Emissions (Receiver Mode) .................... 100 3.3.2 Out of Band Emissions – Radiated (Receiver Mode) ...... 107 APPENDIX.................................................................................... 111 1006-00229 DRTFCC1008-0154(1) Page 3 / 113 Copyright ○ C 2010, Digital EMC Co., Ltd. 1. Equipment information 1.1 Equipment description FCC Equipment Class Digital Transmission System (DTS) Equipment type 2.4 GHz WLAN Module Equipment model name ML-NWA65L Equipment add model name 097N01880 Equipment serial no. Identical prototype Frequency band 2412 ~ 2462 MHz Modulation type CCK, OFDM Channel Access Protocol CSMA/CA Channel Spacing 5.0 MHz Power Supply DC 5.0 V Antenna type Internal Type: PCB Antenna (Max. peak gain: 2.46 dBi) Antenna Configuration TX / RX Diversity: 1TX, 2RX - TX Diversity: A transmitting antenna is selected by RX diversity. Simultaneous transmission is not supported. - This device only supports a HT20 mode of 802.11n. 1.2 Ancillary equipment Equipment Model No. Serial No. Manufacturer Note - - - - - - - - - - 1006-00229 DRTFCC1008-0154(1) Page 4 / 113 Copyright ○ C 2010, Digital EMC Co., Ltd. 2. Information about test items 2.1 Test mode This device was tested in fixed duty cycle mode at maximum power. 2.2 Auxiliary equipment Equipment Model No. Serial No. Manufacturer Note Notebook PSME4K-014001 19101993W TOCHIBA - - - - - - 2.3 Tested frequency TX Frequency (MHz) RX Frequency (MHz) Lowest Channel 2412 2412 Middle Channel 2437 2437 Highest Channel 2462 2462 2.4 Tested environment Temperature : 20 ~ 26 o C Relative humidity content : 33 ~ 47 % R.H. Details of power supply :DC 5.0 V 2.5 EMI Suppression Device(s)/Modifications EMI suppression device(s) added and/or modifications made during testing → None 1006-00229 DRTFCC1008-0154(1) Page 5 / 113 Copyright ○ C 2010, Digital EMC Co., Ltd. 3. Test Report 3.1 Summary of tests FCC Part Section(s) Parameter Limit (Using in 2400 ~ 2483.5MHz) Test Condition Status Note 1 I. Transmit mode (Tx) 15.247(a)(2) /RSS-210(A8.2(a)) 6 dB Bandwidth > 500 kHz Conducted C 15.247(b)(3) /RSS-210(A8.4) Transmitter Output Power < 1Watt C 15.247(c) /RSS-210(A8.5) Out of Band Emissions / Band Edge 20dBc in any 100kHz BW C 15.247(d) /RSS-210(A8.2(b)) Transmitter Power Spectral Density < 8dBm / 3kHz C 15.205 15.209 /RSS-210(A8.5) General Field Strength Limits (Restricted Bands and Radiated Emission Limits) <FCC 15.209 Limits Radiated C 15.207 AC Conducted Emissions EN 55022 AC Line Conducted C 15.203/ A8.4 Antenna Requirements FCC 15.203 - C II. Receive mode (Rx) 15.107 / 7.2.2 /RSS-210(7.2.2) AC Conducted Emissions EN 55022 Line Conducted C 15.109 / 7.2.3.2 /RSS-210(4.8) Receiver Spurious Emissions < FCC 15.109 limits Radiated C Note 1: C=Comply NC=Not Comply NT=Not Tested NA=Not Applicable The sample was tested according to the following specification: ANSI C-63.4-2003, RSS-210 1006-00229 DRTFCC1008-0154(1) Page 6 / 113 Copyright ○ C 2010, Digital EMC Co., Ltd. 3.2 Transmitter requirements 3.2.1 6 dB Bandwidth - Procedure: The bandwidth at 6 dB below the highest inband spectral density was measured with a spectrum analyzer connected to the antenna terminal at the highest, middle and the lowest available channels. After the trace being stable, Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 6dB down one side of the emission. Reset the marker-delta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 6 dB bandwidth of the emission. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest Frequencies Span = 50 MHz (Greater than EBW) RBW = 100 kHz Sweep = auto VBW = ≥ RBW Detector function = peak Trace = max hold - Measurement Data: Comply Test Mode Frequency Transmitting Antenna Test Results (MHz) 802.11b Lowest Ant 2 7.40 Middle Ant 2 7.60 Highest Ant 2 8.20 802.11g Lowest Ant 1 15.80 Middle Ant 1 15.80 Highest Ant 1 15.80 802.11n HT20 Lowest Ant 1 17.05 Middle Ant 1 15.8…

Text truncated - open the document above for the full version.

FCC ID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 1 FCC ID: A3LML-NWA65L Copyright Ⓒ 2010, Digital EMC Co., Ltd. View 2