A3LSMT-I8130Base - UPCS with WiFi 802.11b/g

Quick Guide 1. Introduction This guide is an interim for approval test. It is not a final user’s guide. It covers installation guide and telephone operation only. 2. Installation 2.1 Before you begin Make sure your package includes the items listed here. ‚ 1 Base ‚ 1 Frame ‚ 1 Handset ‚ 1 AC power adaptor for Handset ‚ 2 AC power adaptors for Frame or Base ‚ 1 Battery for Frame ‚ 1 Battery for Handset ‚ 1 charging cradle for Handset ‚ 1 charging cradle for Frame ‚ 1 Telephone line for connecting between Base and telephone wall jack (RJ11) ‚ 1 Ethernet line for connecting between Base and DSL/Cable router (RJ45) 2.2 Layout for devices 2.2.1 Base layout - Rear view - Front view 2.2.2 Handset layout - Front view - Right view - Rear view 2.2.3 Frame layout - Front view - Left view - Right view - Rear view 2.2.4 Charging cradle for Handset - Rear view 2.2.5 Charging cradle for Frame - Rear view 2.3 Installing devices 2.3.1 Installing Base 1. Choose an area near an electrical outlet, a telephone wall jack (RJ11), and a DSL/Cable modem router (RJ45). 2. Plug one end of the telephone line cord into TEL LINE jack on the rear panel of the Base and other end into a modular jack. 3. Plug one end of the ethernet line cord into Internet jack on the rear panel of the Base and other end into a LAN port of your DSL/Cable modem router. 4. Plug the AC power adaptor into the electrical outlet and the DC connector into the power jack of the Base. (Base and Frame power adaptors are the same.) - Even if you don’t have a DSL/Cable modem router, you can make a call and answer. 2.3.2 Installing Handset 1. Separate battery door by pushing the door down. 2. Plug the battery pack cord into the jack. 3. Insert battery pack. 4. Close the door by pushing up. 5. Then the power is automatically on. 6. Plug AC power adaptor into the jack of charging cradle. (Connector of handset power adaptor is different from those of Base and Frame.) 7. Place the handset in the cradle. 2.3.3 Installing Frame 1. Plug the battery pack into the back of Frame. 2. Plug AC power adaptor into the jack of charging cradle. (Base and Frame power adaptors are the same.) 3. Place the frame in the cradle. 4. Hold green button for a while. 5. Then the power is on and system boots up. 6. If you don’t have a DSL/Cable modem router, the frame cannot obtain IP address. You can choose “Use phone features only” button in booting time. 3. Telephone Operation 3.1 Make a call 3.1.1 Make a call with Handset 3.1.1.1 Make a call with Handset (Overlap mode) 1. Press Green button. 2. Then you can hear dial tone. 3. Press digits to make a call. (E.g. 12135431234) 3.1.1.2 Make a call with Handset (Enbloc mode) 1. Press digits to make a call. (E.g. 12135431234) 2. Press Green button. 3. Then you can hear DTMF tones. 3.1.2 Make a call with Frame 3.1.2.1 Make a call with Frame (Overlap mode) 1. Press Green button 2. Then you can hear dial tone and see the following call screen. 3. Press digits to make a call. (E.g. 12135431234) 3.1.2.2 Make a call with Frame (Enbloc mode) 1. Press “Keypad” button in the following touch screen. 2. Then pop up the call screen. 3. Press digits to make a call. (E.g. 12135431234) 4. Press Green button. 5. Then you can hear DTMF tones. 3.2 Answer calls 3.2.1 Answer calls with Handset - When the phone rings, press Green button or “Answer” soft button. 3.2.2 Answer calls with Frame - When the phone rings, press Green button or “Answer” soft button. 3.3 Intercom 3.3.1 Make an intercom call with Handset 1. Press Intercom button on right side. 2. Then you can see device lists you can make an intercom call. 3. Scroll and click the device you want to connect. 3.3.2 Make an intercom call with Frame 1. Press Intercom button on right side or touch Intercom button in the call screen. 2. Then you can see device lists you can make an intercom call. 3. Touch the device you want to connect. Consumer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the back of this equipment is a label that contains, among other information, a product identifier in the format US:A3LW400BSMT-i8130. If requested, this number must be provided to the telephone company. An applicable certification jacks Universal Service Order Codes(USOC) for the equipment is provided RJ11, RJ45 in the packaging with each piece of approval terminal equipment. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:A3LW400BSMT-i8130. The digits represented by 00 are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in…

Text truncated - open the document above for the full version.

SAMSUNG ELECTRONICS CO., LTD. 416 Maetan3-Dong, Yeongtong-gu, Suwon city, Gyeonggi-Do, Korea 442-600 Date : January. 16. 2008 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Mr. sung-kyu Cho of Korea Testing Laboratory and hereafter referred to as KTL, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Mr. sung-kyu Cho of KTL on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Steve Kim General Manager REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

SAMSUNG ELECTRONICS CO., LTD. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: A3LSMT-I8130 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Circuit description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until March 31, 2008. External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards General Manager Steve Kim Date 16 of January , 2008

1 Chris Harvey From:  [[email protected]] Sent: Friday, February 29, 2008 7:42 AM To: [email protected] Cc: [email protected]; [email protected] Subject: RE: SAMSUNG ELECTRONICS CO., LTD., FCC ID: A3LSMT-I8130, Assessment NO.: AN08T7631, Notice#2 Attachments: A3LSMT-I8130,UPCS portion.zip; A3LSMT-I8130,WLAN portion.zip A3LSMT-I8130,UPC S portion.zip ... A3LSMT-I8130,WLA N portion.zip ... Dear Chris, I attached application documents separate UPCS and WiFi portion. These are my answers. 1. The text in the antenna specification exhibits is not legible. Please submit replacement antenna specification exhibits that can be read which should include peak gain information for each antenna. Ans)Please refer to the attached revised antenna specification exhibits. 2. The Antennas are stated as 0dBi on pages 17 and 27 in Block/Circuit desc exhibit, 2dBi on page 32 of same exhibit (and states that UPCS has only 1 antenna) but UPCS test report states the antenna is 3.5dBi gain and WLAN report states 2.48dB gain. The MPE exhibit states the UPCS antenna is 3.5dBi gain and WLAN antenna is 4.5dBi gain. Please correct all exhibits to be consistent. Ans)Please refer to the attached revised circuit description, and I will send revised MPE test report in a soon. 3. Please indicate if the WLAN can transmit at the same time as the UPCS transmission. The MPE calculation submitted does not address simultaneous transmission. Ans) WLAN can transmit at the same time as the UPCS transmission. I will send revised MPE test report in a soon. 4. The Schematic Diagram for this Base unit contains a location for the WLAN mini-PCI slot but does not contain the WLAN RF Schematic. Please provide the RF Schematic for the WLAN module. Ans)Please refer to the attached revised circuit diagram. I put the WLAN RF module circuit diagram. 5. The Quick Guide has FCC RF Exposure guidance but it is a little confusing regarding which guidance is for each of the 3 different devices (Base, Frame and Handset) of this system. Please clarify this RF Exposure guidance section to clearly indicate which guidance is for each portion of this system. Ans)Please refer to the attached revised Quick Guide. 6. The WLAN RF Test report documents the Peak Power output test stating on page 10 that a 30kHz RBW is used , with plots showing a 1MHz RBW, but the emission bandwidth is much greater than 1MHz. Please explain this measurement, including how this measurement complies with the FCC's DTS measurement guide http://fjallfoss.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?id=21124&sw itch=P 7. The Peak Power Spectral Density measurement has not been performed in accordance with the DTS measurement guide referenced above. The span is expected to be much smaller than shown and the sweep time would be much longer than shown. Please revise the test report to include PPSD measurements in accordance with the FCC's DTS measurement guide. 2 8. Please submit Radiated Spurious emissions data for the restricted band frequencies at the low and high band edges (2.39GHz and 2.4835GHz). Ans)Please refer to the attached revised WLAN test report. 9. The UPCS test report seems to have several errors: a. The emission bandwidth table has EBW measured values that do not seem to match the plots b. The middle channel plot seems to have a display line that is more than 26dB down from the peak, resulting in 26dB EBW stated value that is wider than the measurement indicates. c. It is not specified which values of the EBW was used to determine the Power Limits of the Peak transmit power section. Please ensure that you are using the measured EBW values and show all calculations used in the report (show EBW, and the calculation for power limit), including any reduction of power limits due to antenna gain. d. Please update the test report to show the calculation for all limits included in the test report. Ans)Please refer to the attached revised UPCS test report. Thankyou. Best Regards, sung-kyu Cho -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Friday, February 29, 2008 5:23 AM To: [email protected] Cc: [email protected] Subject: SAMSUNG ELECTRONICS CO., LTD., FCC ID: A3LSMT-I8130, Assessment NO.: AN08T7631, Notice#2 Dear Sung-kyu Cho, You are listed as the Technical Contact for the above referenced TCB application. The following item(s) need(s) to be resolved before the review can be continued: The UPCS and WLAN portions of this device must be submitted in separate composite device applications per Notice #1. 1. The text in the antenna specification exhibits is not legible. Please submit replacement antenna specification exhibits that can be read which should include peak gain information for each antenna. 2. The Antennas are stated as 0dBi on pages 17 and 27 in Block/Circuit desc exhibit, 2dBi on page 32 of same exhibit (and states that UPCS has only 1 antenna) but UPCS test report states the antenna is 3.5dBi gain and WLAN report states 2.48dB gain. The MPE exhibit states the UPCS antenna is 3.5dBi gain and WLAN antenna is 4.5dBi gain. Please correct all exhibits to be consistent. 3. Please indicate if the WLAN can transmit at the same time as the UPCS transmission. The MPE calculation submitted does not address simultaneous transmission. 4. The Schematic Diagram for this Base unit contains a location for the WLAN mini-PCI slot but does not contain the WLAN RF Schematic. Please provide the RF Schematic for the WLAN module. 5. The Quick Guide has FCC RF Exposure guidance but it is a little confusing regarding which guidance is for each of the 3 different devices (Base, Frame and Handset) of this system. Please clarify this RF Exposure guidance section to clearly indicate which guidance is for each portion of this system. 6. The WLAN RF Test report documents the Peak Power output test stating on page 10 that a 30kHz RBW is used , with plots showing a 1MHz RBW, but the emission bandwidth is much greater than 1MHz. Please explain th…

Text truncated - open the document above for the full version.

Photographs (Outside)

Photographs (In-side)

1 WINiZEN Co., Ltd. December 31, 2007 베이스스테이션 External Antenna Size : 120 X 11 mmWeight : 11.2 gCable : I–Pex 180 mm 2 WINiZEN Co., Ltd. Photo Antenna Air Antenna Air Smith Chart Return Loss V. S. W. R 3 WINiZEN Co., Ltd. Measurement Configuration Antenna Air Antenna Air Axis Definitions Azimuth Pattern Elevation Pattern 4 WINiZEN Co., Ltd. Photo Photo Photo Photo Photo Photo 5 WINiZEN Co., Ltd. Photo Set P1 Set P1 Smith Chart Return Loss V. S. W. R

Page 1 of 3 Pages 222-13, Guro3-Dong Guro-Gu Seoul 152-718, Korea. Tel. : +82-2-860-1463 http://www.ktl.re.kr Fax. : +82-2-860-1468 FP-204-03-01 RF EXPOSURE INFORMATION 1. MPE Limits The limit for Maximum Permissible Exposure (MPE), specified in FCC §1.1310, is lieted in Table 1 According to FCC §1.1310 : the criteria listed in the following table shall be used to evaluate the environmetal impact of human exposure to radio-frequency(RF) radiation as specified in §1.1307(b). Table 1. Limits for Maximum Frequency Range (MHz) Electric Field Strengh (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits For Occupational / Control Exposures (f= frequency) 30-300 61.4 0.163 1.0 6 300-1500 ... ... ... 6 1500-100,000 ... ... ... 6 (B) Limits For General Population / Uncontrolled Exposure (f=frequency) 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 2. EUT information Type of equipment : UPCS(DECT)/WLAN 802.11b/g Model Name : SMT-I8130 FCC ID : A3LSMT-I8130 Frequency Band : UPCS DECT (1921.536 MHz ~ 1928.448 MHz) WLAN 802.11b/g (2412 MHz~ 2462 MHz) UPCS and WLAN can transmit simultaneously. Procedure The procedure used to determine the RF power density was based upon a calculation for determining compliance with the MPE requirements. The power generated by each transmitter used in this was initially measured by a power and the powers were recorded . Through use of the Friis transmission fomula and knowledge of the maximum antenna gain to be used, the power density level is calculated at a distance of 20 cm. The antenna gains of each antenna to be used with the WLAN and UPCS transmitters were used to calculate the MPE in all relevant bands of operation. Page 2 of 3 Pages 1271-12, Sa-Dong Sangnoek-Gu Kyung ki-Do , Korea. Tel. : +82-31-5000-131 http://www.ktl.re.kr Fax. : +82-31-5000-159 FP-204-03-01 Friis Transmission Formula Friis transmission formula : S =(P out *G) / (4πr 2 ) , r = √PG/4πS Where, S= Power Density (mW/cm 2 ) π=3.1416 P out = out power to antenna(mW) r=distance between observation point and center of the radiator(cm) 3. Calculated MPE The highest RF powered measured in each band was used to determine the maximum theoretical antenna gain in that band. The power density limit for General Population/Uncontrolled Exposure at each frequency is determined based on the information in Table 1. Table 2. Calculated MPE Data for UPCS Frequency 1921.536 MHz Limit 1.0 mW/cm 2 Distance (cm), R 20 cm Power (dBm), P 19.03 dBm (79.98 mW) Tx Ant Gain(dBi), G 3.494 (2.236 numeric) Power Density (mW/cm 2 ) 0.035596194 Minimum Distance 3.78 cm Table 3. Calculated MPE Data for WLAN 802.11b Frequency 2412 MHz Limit 1 mW/cm 2 Distance (cm), R 20 cm Power (dBm), P 20.87 dBm ( 122.18 mW) Tx Ant Gain(dBi), G 4.493 (2.814 numeric) Power Density (mW/cm 2 ) 0.068434418 Minimum Distance 5.23 cm Table 4. Calculated MPE Data for WLAN 802.11g Frequency 2412 MHz Limit 1 mW/cm 2 Distance (cm), R 20 cm Power (dBm), P 17.12 dBm ( 51.52 mW) Tx Ant Gain(dBi), G 4.493 (2.814 numeric) Power Density (mW/cm 2 ) 0.028856942 Minimum Distance 3.40 m Page 3 of 3 Pages 1271-12, Sa-Dong Sangnoek-Gu Kyung ki-Do , Korea. Tel. : +82-31-5000-131 http://www.ktl.re.kr Fax. : +82-31-5000-159 FP-204-03-01 4. Summary of Results Table 5. Maximum Permissible Summary Table Frequency Band (MHz) Maximum Antenna Gain (dBi) MPE at 20 cm (mW/cm 2 ) MPE Limit 20 cm (mW/cm 2 ) Test Result 1921.536~ 1928.448 3.494 0.035596194 1 PASS 2412 ~ 2462 (802.11b) 4.493 0.068434418 1 PASS 2412 ~ 2462 (802.11g) 4.493 0.028856942 1 PASS 5. Conclusion Calculations show that Radio devices with described antennas complied with Maximum Permissible (MPE) limit for the General Population/Uncontrolled Exposure

Report No.: 08-2341-009-2 Page 1 of 42 Pages 1271-12, Sa-Dong Sangnok-Gu, Ansan-si Gyunggi-Do , Korea. Tel. : +82-31-5000-131 http://www.ktl.re.kr Fax. : +82-31-5000-159 FP-204-03-01 TEST REPORT 1. Applicant Name : SAMSUNG ELECTRONICS CO., LTD. Address : 2. Products Name : AT&T HomeManager Model/Type : SMT-i8130 Manufacturer : SAMSUNG ELECTRONICS CO., LTD. 3. Test Standard : 4. Test Method : ANSI C63.4-2003 5. Test Result : Positive 6. Date of Application : January 14, 2008 7. Date of Issue : February 19, 2008 Tested by Approved by ` Bum-Jong Kim Seok-Jin Kim Telecommunication Team Engineer Telecommunication Team Manager The test results contained apply only to the test sample(s) supplied by the applicant, and this test report shall not be reproduced in full or in part without approval of the KTL in advance. 416 Maetan3-Dong Yeongtong-gu, Suwon city, Gyeonggi-Do, Korea 442-600 CFR 47 Part 15, Subpart C Report No.: 08-2341-009-2 Page 2 of 42 Pages 1271-12, Sa-Dong Sangnok-Gu, Ansan-si Gyunggi-Do , Korea. Tel. : +82-31-5000-131 http://www.ktl.re.kr Fax. : +82-31-5000-159 FP-204-03-01 TABLE OF CONTENTS 1. GENERAL INFORMATIONS .........................................................................................3 1.1. Applicant (Client) ..............................................................................................................................................3 1.2. Equipment (EUT)...............................................................................................................................................3 1.3. Testing Laboratory............................................................................................................................................3 2. SUMMARY OF TEST RESULTS ...................................................................................4 3. TEST FACILITY .............................................................................................................5 3.1. Korea Testing Laboratory test location ..........................................................................................................5 4. MEASUREMENT & RESULTS ......................................................................................6 4.1. 6dB Bandwidth ..................................................................................................................................................6 4.1.1. Test Setup Layout ....................................................................................................................................6 4.1.2. Test Condition ..........................................................................................................................................6 4.1.3. Test result .................................................................................................................................................6 4.2. Maximum Peak Power ....................................................................................................................................10 4.2.1. Test Setup Layout ..................................................................................................................................10 4.2.2. Test Condition ........................................................................................................................................10 4.2.3. Test result ...............................................................................................................................................10 4.3. 100 KHz Bandwidth of Frequency Band Edges ...........................................................................................14 4.3.1. Test Setup Layout ..................................................................................................................................14 4.3.2. Test Condition ........................................................................................................................................14 4.3.3. Test result ...............................................................................................................................................14 4.4. Power Spectral Density ..................................................................................................................................19 4.4.1. Test Setup Layout ..................................................................................................................................19 4.4.2. Test Condition ........................................................................................................................................19 4.4.3. Test result ...............................................................................................................................................19 4.5. Radiated Emissions (FCC Part15.209).........................................................................................................23 4.5.1. Test Procedure .......................................................................................................................................23 4.5.2. Limits ......................................................................................................................................................24 4.5.3. Sample Calculation ................................................................................................................................25 4.5.4. Photograph for the test configuration.....................................................................................................25 4.5.5. Test Results............................................................................................................................................26 4.6. Conducted Emissions (FCC Part 15.207) .....................................................................................................33 4.6.1. Test Procedure .......................................................................................…

Text truncated - open the document above for the full version.

TEST Setup Photographs < Radiated emission Test > < Radiated emission Test > < RF conducted Test > < Conducted emission Test > <Conducted emission Test >