A4C-10013BGPS Device

QUICK START GUIDE Support randmcnally.com/support 1-877-446-4863 TND550QSG_033120_v001 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC SAR exposure limits set forth for an uncontrolled environment. SAR compliance for using the equipment in close proximity to the human body has been evaluated at 0mm. This equipment must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and consider removing the no-collocation statement. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipment should be installed and operated with a minimum distance of 0mm between the radiator and your body. Cet équipement devrait être installé et actionné avec une distance minimum de 0mm entre le radiateur et votre corps. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. 23TND ™ 550 Quick Start GuideTND ™ 550 Quick Start Guide Box Contents 1 TND ™ 550 Unit 2 Sucktion cup mount with adjustable bracket 3 Vehicle charger 4 Mini USB cable 5 Anti-glare screen protector Your TND ™ 550 Unit Caution: Important Safety Information Navigation • Use this device at your own risk. • Attend to this device only when it is safe to do so. • Traffic laws and regulations always have priority over any instructions from the navigation system. NOTE: If you do not understand the spoken instructions or are unsure of what to do, refer to the navigation map on your device. Installation • Make sure that the mount is securely mounted and properly adjusted before each trip. • Make sure that the mount does not impair the driver’s visibility. • Do not attach the mount within the airbag deployment zone. • Install the mount in a manner that minimizes risk in the event of an accident. • After installation, check all safety-related equipment to ensure that it operates without interference from the device, its cables, or any other accessories. • Connect the vehicle charger to a 12V outlet only. • The device can also be charged using a standard Micro USB charger. Device • Do not use sharp-edged objects on the device touch screen. • The device is not waterproof and is not protected against water damage. • Protect the device from extreme temperatures. Operating temperature for the device is between 32 degrees F and 120 degrees F. • Do not open the device casing. • Do not attempt to replace the battery. Contact Rand McNally Customer Support with questions about the battery. • Always follow local regulations when disposing of this device. NOTE: Make sure that there are no kinks in the cable and that it will not be damaged by any sharp objects. NOTE: Use only a moist cloth to clean the device. NOTE: Do not pull the cable to unplug the unit. Your TND ™ 550 3 1 4 5 2 45TND ™ 550 Quick Start GuideTND ™ 550 Quick Start Guide Your TND ™ 550 Install the Mount NOTE: Follow all local regulations governing the placement of the mount. 1. Select an area with a line of sight to the sky and GPS satellites. 2. Clean and dry the mounting area. 3. Remove the suction cup protective film. 4. Adjust the angle of the mount using the thumb screws. 5. Pull the suction cup lever up to release suction. 6. Plug the power cord into the device and the vehicle’s 12-volt power source. 7. Optional: To use your vehicle’s speakers, connect an AUX cable from the device’s AUX out to your vehicle’s AUX in port. 8. Slide the device onto the mount. 9. Place and hold the mount suction cup against the mounting surface. 10. Press the suction cup lever down until it snaps into place. 11. Adjust the device so that it can be easily seen and does not block the driver ‘s line of sight. Mini USB TND ™…

Text truncated - open the document above for the full version.

Declaration statement Letter 2021-01-26 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Declaration statement Letter To Whom It May Concern: We hereby declare that (FCC ID: A4C-10013B) fulfill the requirements of 47 CFR Part 15C Section 15.247(g) & 15.247(h). Compliance for section 15.247(g) According to Bluetooth Core Specification, the Bluetooth system transmits the packet with the pseudorandom hopping frequency with a continuous data and the short burst transmission from the Bluetooth system is also transmitted under the frequency hopping system with the pseudorandom hopping frequency system. Compliance for section 15.247(h) According to Bluetooth Core specification, the Bluetooth system incorporates with an adaptive system to detect other user within the spectrum band so that it individually and independently to avoid hopping on the occupied channels. According to the Bluetooth Core specification, the Bluetooth system is designed not have the ability to coordinated with other FHSS System in an effort to avoid the simultaneous occupancy of individual hopping frequencies by multiple transmitter. Please contact me if there is any information you may need. Sincerely, Name: Kristalyn Wilkerson Position: CFO Company Name: RM Acquisition LLC. Address: 8770 W. Bryn Mawr Avenue Tel / Fax 8473296590 / 8473296101 E-Mail: [email protected]

RM Acquisition LLC. Agent Authorization Letter 2021-01-26 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen Huaxia Testing Technology Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Name: Kristalyn Wilkerson Position: CFO Company Name: RM Acquisition LLC. Address: 8770 W. Bryn Mawr Avenue Tel / Fax 8473296590 / 8473296101 E-Mail: [email protected]

Application cover letter 2021,01,27 Dear MET Reviewer, This is a new Application from RM Acquisition LLC. EUT Name: GPS Device Model No.: TND550 FCC ID: A4C-10013B IC: 10199A-10013B Fuction: Bluetooth&WiFi&GPS Apply for certification:FCC ID& ISED Thank you for your cooperation! Yours sincerely, Signatory: Name: Kristalyn Wilkerson Position: CFO Company Name: RM Acquisition LLC. Address: 8770 W. Bryn Mawr Avenue Tel / Fax 8473296590 / 8473296101 E-Mail: [email protected]

RM Acquisition LLC. Long Term Confidentiality Request Letter 2021-01-26 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (FCC ID: A4C-10013B) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - e.g. Block diagram - e.g. SCH - e.g. Operational Description required to be submitted with this application be permanently withheld from public review. The above documents are company proprietary information that could never get into the possession of your competition. Please contact me if there is any information you may need. Sincerely, Name: Kristalyn Wilkerson Position: CFO Company Name: RM Acquisition LLC. Address: 8770 W. Bryn Mawr Avenue Tel / Fax 8473296590 / 8473296101 E-Mail: [email protected]

Test model No.: TND550

Test model No.: TND550

Shenzhen Huaxia Testing Technology Co., Ltd 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China Telephone: +86-755-26648640 Fax: +86-755-26648637 Website: www.cqa-cert.com R eport Template Version: V04 Report Template Revision Date: 2018-07-06 Test Report The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s) tested. Without written approval of CQA, this report can’t be reproduced except in full. Report No. : CQASZ20201201549E-01 Applicant: Address of Applicant: RM Acquisition LLC. 8770 W. Bryn Mawr Avenue Equipment Under Test (EUT): EUT Name: GPS Device Model No.: TND550 Brand Name: FCC ID: A4C-10013B Standards: 47 CFR Part 15, Subpart C Date of Receipt: 2020-12-28 Date of Test: 2020-12-28 to 2021-01-08 Date of Issue: 2021-01-08 Test Result : PASS* *In the configuration tested, the EUT complied with the standards specified above Tested By˖˖ (Tiny You ) Reviewed By: ( Ares Liu ) Approved By: (Sheek Luo) Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20201201549E-01 Page:2 of 99 1 Version Revision History Of Report Report No. Version Description Issue Date CQASZ20201201549E-01 Rev.01 Initial report 2021-01-08 Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20201201549E-01 Page:3 of 99 2 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 (2013) PASS AC Power Line Conducted Emission 47 CFR Part 15, Subpart C Section 15.207 ANSI C63.10 (2013) N/A Conducted Peak Output Power 47 CFR Part 15, Subpart C Section 15.247 (b)(1) ANSI C63.10 (2013) PASS 20dB Occupied Bandwidth 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013) PASS Carrier Frequencies Separation 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013) PASS Hopping Channel Number 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013) PASS Dwell Time 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013) PASS Pseudorandom Frequency Hopping Sequence 47 CFR Part 15, Subpart C Section 15.247(b)(4)&TCB Exclusion List (7 July 2002) ANSI C63.10 (2013) PASS Band-edge for RF Conducted Emissions 47 CFR Part 15, Subpart C Section 15.247(d) ANSI C63.10 (2013) PASS RF Conducted Spurious Emissions 47 CFR Part 15, Subpart C Section 15.247(d) ANSI C63.10 (2013) PASS Radiated Spurious emissions 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 (2013) PASS Restricted bands around fundamental frequency (Radiated Emission) 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 (2013) PASS N/A: This EUT is designed to use in vehicle only and received DC charging power from the vehicle power supply system, so Not Applicable. Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20201201549E-01 Page:4 of 99 3 Contents Page 1 VERSION .................................................................................................................................................................. 2 2 TEST SUMMARY .................................................................................................................................................... 3 3 CONTENTS .............................................................................................................................................................. 4 4 GENERAL INFORMATION ................................................................................................................................... 5 4.1 CLIENT INFORMATION .......................................................................................................................................... 5 4.2 GENERAL DESCRIPTION OF EUT .......................................................................................................................... 5 4.3 ADDITIONAL INSTRUCTIONS................................................................................................................................. 7 4.4 TEST ENVIRONMENT ............................................................................................................................................ 8 4.5 DESCRIPTION OF SUPPORT UNITS ......................................................................................................................... 8 4.6 STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................. 9 4.7 TEST LOCATION ................................................................................................................................................. 10 4.8 TEST FACILITY ................................................................................................................................................... 10 4.9 ABNORMALITIES FROM STANDARD CONDITIONS ............................................................................................... 10 4.10 OTHER INFORMATION REQUESTED BY THE CUSTOMER ...................................................................................... 10 4.11 EQUIPMENT LIST ................................................................................................................................................ 11 5 TEST RESULTS AND MEASUREMENT DATA .............................................................................................. 12 5.1 ANTENNA REQUIREMENT ................................................................................................................................... 12 5.2 CONDUCTED PEAK OUTPUT POWER ................................................................................................................... 13 5.3 20DB OCCUPY BANDWIDTH ............................................................................................................................... 20 5.4 CARRIER FREQUENCIES SEPARATION ....................................…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup 1.1 Radiated Emission 9KHz~30MHz: 30MHz~1GHz: Above 1GHz: