A7K-SLMB3AwoX StriimLIGHT TM mini

3 W 3.2 1 Important Important safety instructions •Read these instructions. •Keep these instructions. •Heed all warnings. •Follow all instructions. •Do not use this apparatus near water. •Clean only with dry cloth. •Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. •Do not install near any heat sources such as radiators, heat registers, stoves, or produce heat. • Only use attachments/accessories by the manufacturer. •Unplug this apparatus during lightning storm or when unused for long periods of time. •Refer all servicing personnel. Servicing is required when the apparatus has been damaged in any way, such as power -supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. •Battery usage CAUTION - To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit: • Install all batteries correctly, + and - as marked on the unit. • Do not mix batteries (old and new or carbon and alkaline, etc.). • than that of the lamps for which they are a replacement, attention should be drawn to the fact that the increased weight may reduce the mechanical stability of certain • Not for totally enclosed luminaires. • Not for emergency lighting. luminaires and lamp holders and may impair contact making and lamp retention. DO NOT INGEST BATTERY,CHEMICAL BURN HAZARD. • Remove batteries when the unit is not used for a long time. • The batteries shall not be exposed to the like. • WARNING • The product/remote control may contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal bur ns can occur within two hours of ingestion. • If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention. • When you change the batteries, al ways keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery. • Caution: Danger of explosion if battery is incorrectly replace. Replace with only the same or equivalent type. • If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer. • Do not ingest battery, chemical bur n hazard. •Apparatus shall not be exposed to dripping or splashing. •Do not place any sources of danger on the apparatus objects, lighted candles). •This apparatus may contain lead and mercury. Dispose according to local, State or Federal laws. For disposal or recycling inf or mation, please contact your local authorities. •Do not place this apparatus on the fur niture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling apparatus can cause serious injury or even death. The 'exclamation point' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. WARNING: electric shock, this apparatus should not be with liquids, such as vases, should not be placed on this apparatus. Care f or your product Care of the envir onment Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Never dispose of your product with other household waste. Please infor m yourself about the local rules on the separate collection of electrical and electronic products and batteries. The correct disposal of these products helps prevent potentially negative consequences on the environment and human health. The batteries supplied do not contain the heavy metals mercury and cadmium. Never theless, in many areas batteries may not be disposed of with your household waste. Please ensure you dispose of batteries according to local regulations. • Added weight of the device may cause instability of a free-standing portable luminaire. • This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. Make sure to leave a space of 7.8 inches (20cm) or more around this apparatus. • • • This 'bolt of lightning' indicates uninsulated material within your unit may cause an electrical shock. For the safety of ever yone in your household, please do not remove product co ver ing. •Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. • Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This symbol indicates that the unit has a double insulation system. Class II equipment symbol FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Project No.: 1402C037 Page 2 of 9 Neutron Engineering Inc. Project No.: 1402C037 Page 3 of 9

SLMB3 5mm E364369 35±1mm 1 37±1mm 2 ELECTRIC SHOCK RISK-ONLY FOR DRY LOCATIONS DO NOT USE WITH DIMMERS NOT FOR TOTALLY ENCLOSED LUMINAIRES 10994A RISK OF ELECTRIC SHOCK DO NOT OPEN SLMB3 安规只作样板 SLMB3 E364369 ELECTRIC SHOCK RISK-ONLY FOR DRY LOCATIONS DO NOT USE WITH DIMMERS NOT FOR TOTALLY ENCLOSED LUMINAIRES 10994A RISK OF ELECTRIC SHOCK DO NOT OPEN SLMB3

Neutron Engineering Inc. Project No.: 1402C037 Page 4 of 9 Neutron Engineering Inc. Project No.: 1402C037 Page 5 of 9 Neutron Engineering Inc. Project No.: 1402C037 Page 6 of 9 Neutron Engineering Inc. Project No.: 1402C037 Page 7 of 9 Neutron Engineering Inc. Project No.: 1402C037 Page 8 of 9 Neutron Engineering Inc. Project No.: 1402C037 Page 9 of 9

Neutron Engineering Inc. FCC RF EXPOSURE REPORT FCC ID: A7K-SLMB3 Project No. : 1402C037 Equipment : AwoX StriimLIGHT TM mini Model : SLm-B3 Applicant : AW O X Address : 93 place Pierre Duhem, 34000 Montpellier, France According: : FCC Guidelines for Human Exposure IEEE C95.1 Neutron Engineering Inc. No.3, Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. GENERAL CONCULUSION: Table for Filed Antenna: Ant Brand Model Name Antenna TypeConnector Gain (dBi) 1 N/A N/A Printed N/A 2.12 Maximum measured transmitter power: Output Power (dBm) Out Power (mW) Limit (mW) 3.99 2.5 10 According to FCC KDB447498 V05, Appendix A, SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm The maximum measured output power of this EUT is 2.02dBm (1.6mW), less than 10mW at 5mm distance. Conclusion: No SAR evaluation required since transmitter power is below FCC threshold

Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 1 of 93 FCC&IC Radio Test Report FCC ID: A7K-SLMB3 IC: 10994A-SLMB3 This report concerns (check one): Original Grant Class II Change Issued Date : Mar. 03, 2014 Project No. : 1402C037 Equipment : AwoX StriimLIGHT TM mini Model Name : SLm-B3 Applicant : Awox SA Address : 93 place Pierre Duhem, 34000 Montpellier, France. Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Feb. 19, 2014 Date of Test: Feb. 19, 2014~ Feb. 28, 2014 Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory: (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL: 0769-8318-3000 FAX: 0769-8319-6000 Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 2 of 93 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of CHINA, or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 3 of 93 Table of Contents Page REPORT ISSUED HISTORY 6 1 . CERTIFICATION 7 2 . SUMMARY OF TEST RESULTS 8 2.1 TEST FACILITY 9 2.2 MEASUREMENT UNCERTAINTY 9 3 . GENERAL INFORMATION 10 3.1 GENERAL DESCRIPTION OF EUT 10 3.2 DESCRIPTION OF TEST MODES 12 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 12 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 3.5 DESCRIPTION OF SUPPORT UNITS 13 4 . EMC EMISSION TEST 14 4.1 CONDUCTED EMISSION MEASUREMENT 14 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 14 4.1.2 TEST PROCEDURE 14 4.1.3 DEVIATION FROM TEST STANDARD 14 4.1.4 TEST SETUP 15 4.1.5 EUT OPERATING CONDITIONS 15 4.1.6 EUT TEST CONDITIONS 15 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 18 4.2.1 RADIATED EMISSION LIMITS 18 4.2.2 TEST PROCEDURE 19 4.2.3 DEVIATION FROM TEST STANDARD 19 4.2.4 TEST SETUP 20 4.2.5 EUT OPERATING CONDITIONS 21 4.2.6 EUT TEST CONDITIONS 21 4.2.7 TEST RESULTS (BELOW 30MHZ) 22 4.2.8 TEST RESULTS: 30MHZ - 1000MHZ 23 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 30 5 . NUMBER OF HOPPING CHANNEL 45 5.1 APPLIED PROCEDURES 45 5.1.1 TEST PROCEDURE 45 5.1.2 DEVIATION FROM STANDARD 45 5.1.3 TEST SETUP 45 5.1.4 EUT OPERATION CONDITIONS 45 5.1.5 EUT TEST CONDITIONS 45 Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 4 of 93 Table of Contents Page 5.1.6 TEST RESULTS 46 6 . AVERAGE TIME OF OCCUPANCY 47 6.1 APPLIED PROCEDURES / LIMIT 47 6.1.1 TEST PROCEDURE 47 6.1.2 DEVIATION FROM STANDARD 47 6.1.3 TEST SETUP 47 6.1.4 EUT OPERATION CONDITIONS 48 6.1.5 EUT TEST CONDITIONS 48 6.1.6 TEST RESULTS 49 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 61 7.1 APPLIED PROCEDURES / LIMIT 61 7.1.1 TEST PROCEDURE 61 7.1.2 DEVIATION FROM STANDARD 61 7.1.3 TEST SETUP 61 7.1.4 EUT TEST CONDITIONS 61 7.1.5 TEST RESULTS 62 8 . BANDWIDTH TEST 66 8.1 APPLIED PROCEDURES 66 8.1.1 TEST PROCEDURE 66 8.1.2 DEVIATION FROM STANDARD 66 8.1.3 TEST SETUP 66 8.1.4 EUT OPERATION CONDITIONS 66 8.1.5 EUT TEST CONDITIONS 66 8.1.6 TEST RESULTS 67 9 . PEAK OUTPUT POWER TEST 71 9.1 APPLIED PROCEDURES / LIMIT 71 9.1.1 TEST PROCEDURE 71 9.1.2 DEVIATION FROM STANDARD 71 9.1.3 TEST SETUP 71 9.1.4 EUT OPERATION CONDITIONS 71 9.1.5 EUT TEST CONDITIONS 71 9.1.6 TEST RESULTS 72 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 76 10.1 APPLIED PROCEDURES / LIMIT 76 10.1.1 TEST PROCEDURE 76 10.1.2 DEVIATION FROM STANDARD 76 10.1.3 TEST SETUP 77 10.1.4 EUT OPERATION CONDITIONS 77 10.1.5 EUT TEST CONDITIONS 77 10.1.6 TEST RESULTS 78 Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 5 of 93 Table of Contents Page 11 . MEASUREMENT INSTRUMENTS LIST AND SETTING 88 12 . EUT TEST PHOTO 90 Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 6 of 93 REPORT ISSUED HISTORY Issued No. Description Issued Date NEI-FICP-1-1402C037 Original Issue. Mar. 03, 2014 Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 7 of 93 1. CERTIFICATION Equipment : AwoX StriimLIGHT TM mini Brand Name : AwoX Model Name : SLm-B3 Applicant : Awox SA Manufacturer : Awox SA Address : 93 place Pierre Duhem, 34000 Montpellier, France. Factory : 1) Eastech Electronics ( Hui Yang ) Co. Ltd. 2) Eastwin Electronics Technology (Hui Yang) Co.,Ltd Address : 1) Dong Feng District Xinxu, Hui Yang, Hui Zhou,Guangdong,P.R.China 2) Dong Feng District Xinxu, Hui Yang, Hui Zhou,Guangdong,P.R.China Date of Test : Feb. 19, 2014~ Feb. 28, 2014 Test Item : ENGINEERING SAMPLE Standard(s) : FCC Part15, Subpart C : 2012 (15.247) / ANSI C63.4 : 2009 / FCC Public Notice DA 00-705, March 30, 2000. Canada RSS-210: 2010 RSS-GEN Issue 3, Dec 2010 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 90 of 93 12. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 91 of 93 Radiated Measurement Photos 9K~30MHz Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 92 of 93 Radiated Measurement Photos 30~1000MHz Neutron Engineering Inc. Report No.: NEI-FICP-1-1402C037 Page 93 of 93 Radiated Measurement Photos Above 1000MHz