A7K-SLW10AwoX StriimLIGHTTM WiFi

1 Important Important safety instructions •Read these instructions. •Keep these instructions. •Heed all warnings. •Follow all instructions. •Do not use this apparatus near water. •Clean only with dry cloth. •Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. •Do not install near any heat sources such as radiators, heat registers, stoves, or produce heat. • Only use attachments/accessories by the manufacturer. •Unplug this apparatus during lightning storm or when unused for long periods of time. •Refer all servicing personnel. Servicing is required when the apparatus has been damaged in any way, such as power -supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. •Battery usage CAUTION - To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit: • Install all batteries correctly, + and - as marked on the unit. • Do not mix batteries (old and new or carbon and alkaline, etc.). • than that of the lamps for which they are a replacement, attention should be drawn to the fact that the increased weight may reduce the mechanical stability of certain • Not for totally enclosed luminaires. • Not for emergency lighting. luminaires and lamp holders and may impair contact making and lamp retention. DO NOT INGEST BATTERY,CHEMICAL BURN HAZARD. • Remove batteries when the unit is not used for a long time. • The batteries shall not be exposed to the like. • WARNING • The product/remote control may contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal bur ns can occur within two hours of ingestion. • If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention. • When you change the batteries, al ways keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery. • Caution: Danger of explosion if battery is incorrectly replace. Replace with only the same or equivalent type. • If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer. • Do not ingest battery, chemical bur n hazard. •Apparatus shall not be exposed to dripping or splashing. •Do not place any sources of danger on the apparatus objects, lighted candles). •This apparatus may contain lead and mercury. Dispose according to local, State or Federal laws. For disposal or recycling inf or mation, please contact your local authorities. •Do not place this apparatus on the fur niture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling apparatus can cause serious injury or even death. The 'exclamation point' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. WARNING: electric shock, this apparatus should not be with liquids, such as vases, should not be placed on this apparatus. Care f or your product Care of the envir onment Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Never dispose of your product with other household waste. Please infor m yourself about the local rules on the separate collection of electrical and electronic products and batteries. The correct disposal of these products helps prevent potentially negative consequences on the environment and human health. The batteries supplied do not contain the heavy metals mercury and cadmium. Never theless, in many areas batteries may not be disposed of with your household waste. Please ensure you dispose of batteries according to local regulations. • Added weight of the device may cause instability of a free-standing portable luminaire. • This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. Make sure to leave a space of 7.8 inches (20cm) or more around this apparatus. • • • This 'bolt of lightning' indicates uninsulated material within your unit may cause an electrical shock. For the safety of ever yone in your household, please do not remove product co ver ing. •Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. • Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This symbol indicates that the unit has a double insulation system. Class II equipment symbol FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determi…

Text truncated - open the document above for the full version.

RV-0000000 Project No.: 1403C103 Page 1 of 1 0 Neutron Engineering Inc. ATTACHMENT PHOTOGRAPHS OF EUT RV-0000000 Project No.: 1403C103 Page 2 of 1 0 Neutron Engineering Inc. RV-0000000 Project No.: 1403C103 Page 3 of 1 0 Neutron Engineering Inc.

2012-02-21 Xiayuanying EASTECH ELECTRONIC CO.LTD 以上所述物料必須符合東威環保要求。 Johnson Hsu Rata.Tang Zhi Long BJ wei SL-W10 AwoX Wing.Lu 以上只做絲印參考, 不做結構尺寸,孔位參考! Top-cover Top-cover Film BPV100097-0002 ABAAL1110-GU03 1:12:1 2.5mm Silkscreen Color:pantone coolgray 5c Material:plastic, Surface:Paint,亞白(見色板),要求不能導電 FRONT BACK 31.4mm 34.1mm BPV100097-0003与BPV100097-0001的丝印内容和颜色相同.只是价格不同. E364369 10994A E364369 10994A E364369 10994A E364369 10994A

RV-0000000 Project No.: 1403C103 Page 4 of 1 0 Neutron Engineering Inc. RV-0000000 Project No.: 1403C103 Page 5 of 1 0 Neutron Engineering Inc. RV-0000000 Project No.: 1403C103 Page 6 of 1 0 Neutron Engineering Inc. RV-0000000 Project No.: 1403C103 Page 7 of 1 0 Neutron Engineering Inc. RV-0000000 Project No.: 1403C103 Page 8 of 1 0 Neutron Engineering Inc. RV-0000000 Project No.: 1403C103 Page 9 of 1 0 Neutron Engineering Inc. RV-0000000 Project No.: 1403C103 Page 10 of 1 0 Neutron Engineering Inc.

Neutron Engineering Inc. FCC RF EXPOSURE REPORT FCC ID: A7K-SLW10 Project No. : 1403C103 Equipment : AwoX StriimLIGHT TM WiFi Model : SL-W10 Applicant : AWOX Address : 93 place Pierre Duhem, 34000 Montpellier, France According: : FCC Guidelines for Human Exposure IEEE C95.1 Neutron Engineering Inc. No.3, Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. MPE CALCULATION METHOD: Calculation Method of RF Safety Distance: where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Table for Filed Antenna Ant. Manufacturer Model NameAntenna TypeConnector Gain (dBi) 1 MAG.LAYERS PIFA Internal N/A 3.79 Neutron Engineering Inc. TEST RESULTS EUT： AwoX StriimLIGHT TM WiFi Model Name ： SL-W10 Temperature： 25 °C Relative Humidity： 55 % Test Voltage ： DC 3.7V Test Mode ： TX B MODE /CH01, CH06, CH11 Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result 3.79 2.3933 6.27 4.2364 0.002018141 Complies 3.79 2.3933 8.94 7.8343 0.003732081 Complies 3.79 2.3933 9.14 8.2035 0.003907961 Complies EUT： AwoX StriimLIGHT TM WiFi Model Name ： SL-W10 Temperature： 25 °C Relative Humidity： 55 % Test Voltage ： DC 3.7V Test Mode ： TX G MODE /CH01, CH06, CH11 Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result 3.79 2.3933 10.07 10.1625 0.004841171 Complies 3.79 2.3933 12.84 19.2309 0.009161161 Complies 3.79 2.3933 12.96 19.7697 0.009417821 Complies The calculated distance is 20 cm

Neutron Engineering Inc. Report No.: NEI-FICP-2-1403C103 Page 1 of 90 FCC&IC Radio Test Report FCC ID: AK7-SLW10 IC: 10994A-SLW10 This report concerns (check one): Original Grant Class II Change Project No. : 1403C103 Equipment : AwoX StriimLIGHT TM WiFi Model Name : SL-W10 Applicant : AWOX SA Address : 93 place Pierre Duhem, 34000 Montpellier, France. Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Apr. 01, 2014 Date of Test: Apr. 01, 2014~ May. 06, 2014 Issued Date: May. 07, 2014 Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) Neutron Engineering Inc. No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, China. TEL: 0769-8318-3000 FAX: 0769-8319-6000 Neutron Engineering Inc. Report No.: NEI-FICP-2-1403C103 Page 2 of 90 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C, or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutron shall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FICP-2-1403C103 Page 3 of 90 Table of Contents Page 1 . CERTIFICATION 6 2 . SUMMARY OF TEST RESULTS 7 2.1 TEST FACILITY 8 2.2 MEASUREMENT UNCERTAINTY 8 3 . GENERAL INFORMATION 9 3.1 GENERAL DESCRIPTION OF EUT 9 3.2 DESCRIPTION OF TEST MODES 11 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 12 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 3.5 DESCRIPTION OF SUPPORT UNITS 14 4 . EMC EMISSION TEST 15 4.1 CONDUCTED EMISSION MEASUREMENT 15 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 15 4.1.2 TEST PROCEDURE 15 4.1.3 DEVIATION FROM TEST STANDARD 15 4.1.4 TEST SETUP 16 4.1.5 EUT OPERATING CONDITIONS 16 4.1.6 EUT TEST CONDITIONS 16 4.1.7 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 17 4.2.1 RADIATED EMISSION LIMITS 17 4.2.2 TEST PROCEDURE 18 4.2.3 DEVIATION FROM TEST STANDARD 18 4.2.4 TEST SETUP 18 4.2.5 EUT OPERATING CONDITIONS 19 4.2.6 EUT TEST CONDITIONS 19 4.2.7 TEST RESULTS (9KHZ TO 30MHZ) 20 4.2.8 TEST RESULTS (BETWEEN 30MHZ TO 1000 MHZ) 20 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 20 5 . BANDWIDTH TEST 21 5.1 APPLIED PROCEDURES 21 5.1.1 TEST PROCEDURE 21 5.1.2 DEVIATION FROM STANDARD 21 5.1.3 TEST SETUP 21 5.1.4 EUT OPERATION CONDITIONS 21 5.1.5 EUT TEST CONDITIONS 21 5.1.6 TEST RESULTS 21 Neutron Engineering Inc. Report No.: NEI-FICP-2-1403C103 Page 4 of 90 Table of Contents Page 6 . MAXIMUM OUTPUT POWER TEST 22 6.1 APPLIED PROCEDURES / LIMIT 22 6.1.1 TEST PROCEDURE 22 6.1.2 DEVIATION FROM STANDARD 22 6.1.3 TEST SETUP 22 6.1.4 EUT OPERATION CONDITIONS 22 6.1.5 EUT TEST CONDITIONS 22 6.1.6 TEST RESULTS 22 7 . ANTENNA CONDUCTED SPURIOUS EMISSION 23 7.1 APPLIED PROCEDURES / LIMIT 23 7.1.1 TEST PROCEDURE 23 7.1.2 DEVIATION FROM STANDARD 23 7.1.3 TEST SETUP 23 7.1.4 EUT OPERATION CONDITIONS 23 7.1.5 EUT TEST CONDITIONS 23 7.1.6 TEST RESULTS 23 8 . POWER SPECTRAL DENSITY TEST 24 8.1 APPLIED PROCEDURES / LIMIT 24 8.1.1 TEST PROCEDURE 24 8.1.2 DEVIATION FROM STANDARD 24 8.1.3 TEST SETUP 24 8.1.4 EUT OPERATION CONDITIONS 24 8.1.5 EUT TEST CONDITIONS 24 8.1.6 TEST RESULTS 24 9 . MEASUREMENT INSTRUMENTS LIST 25 10 . EUT TEST PHOTO 27 ATTACHMENT A - CONDUCTED EMISSION 31 ATTACHMENT B - RADIATED EMISSION (9KHZ TO 30MHZ) 34 ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) 36 ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) 43 ATTACHMENT E - BANDWIDTH 68 ATTACHMENT F - MAXIMUM OUTPUT POWER 73 ATTACHMENT G - ANTENNA CONDUCTED SPURIOUS EMISSION 75 ATTACHMENT H - POWER SPECTRAL DENSITY 86 Neutron Engineering Inc. Report No.: NEI-FICP-2-1403C103 Page 5 of 90 REPORT ISSUED HISTORY Issued No. Description Issued Date NEI-FICP-2-1403C103 Original Issue. May. 07, 2014 Neutron Engineering Inc. Report No.: NEI-FICP-2-1403C103 Page 6 of 90 1. CERTIFICATION Equipment : AwoX StriimLIGHT TM WiFi Brand Name : AwoX Model Name : SL-W10 Applicant : AWOX SA. Manufacturer : AWOX SA. Address : 93 place Pierre Duhem, 34000 Montpellier, France. Factory : Eastwin Electronics Technology (Hui Yang) Co.,Ltd Address : Dong Feng District Xinxu, Hui Yang, Hui Zhou, Guangdong, P. R. China Date of Test : Apr. 01, 2014~ May. 06, 2014 Test Item : ENGINEERING SAMPLE Standard(s) : FCC Part15, Subpart C(15.247) / ANSI C63.4-2009 Canada RSS-210:2010 RSS-GEN Issue 3, Dec 2010 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FICP-2-1403C103) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of TAF according to the ISO-17025 quality assessment standard and technical standard(s). Neutr…

Text truncated - open the document above for the full version.