A8J-ENS500LONG RANGE WIRELESS 11N OUTDOOR AP/CB

WIRELESS 11N LONG RANGE OUTDOOR AP / CBENS500EXT User GuideV1.0 T ABLE OF C ONTENTS I T ABLE OF C ONTENTS Product Overview Package Contents 1-1 Product Overview 1-2 Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 Software Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1- 3 Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4 Hardware Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4 Software Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4 Environment & Mechanical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4 Wireless Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5 Product Layout 1-6 T ABLE OF C ONTENTS II Installation System Requirements 2-1 Installing the Device 2-2 Pre-Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 Installing the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 Web Configuration Logging In 3-1 Best Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2 Basic Network Settings System Status 4-1 Using Save/Reload 4-1 Viewing System Information 4-2 Viewing Wireless Client List 4-4 Viewing System Log 4-5 Viewing Connection Status 4-6 Viewing DHCP Client Table 4-7 Viewing WDS Link List 4-8 T ABLE OF C ONTENTS III System Setup 4-9 Configuring Operation Mode 4-9 Configuring IP Settings 4-10 Configuring Spanning Tree Settings 4-11 Router Setup 4-12 Configuring WAN Settings 4-12 Static IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 2 Dynamic IP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13Point-to-Point Protocol over Ethernet (PPPoE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Point-to-Point Tunnelling Protocol (PPTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Configuring LAN Settings 4-17 Configuring VPN Pass-Through 4-18 Configuring Port Forwarding 4-19 Configuring Demilitarized Zone 4-21 Configuring Wireless LAN 4-22 Configuring Wireless Settings 4-22 Access Point Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Client Bridge Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24 WDS Bridge Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25 Client Router Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 T ABLE OF C ONTENTS IV Configuring Wireless Security 4-28 Wired Equivalent Privacy (WEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28 Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK). . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Mixed . . . . . . . . . . . . . . . . . . . . . . . 4-31 Wi-Fi Protected Access (WPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32 Wi-Fi Protected Access 2 (WPA2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33 Wi-Fi Protected Access (WPA) Mixed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 Configuring Wireless MAC Filter 4-35 Configuring WDS Link Settings 4-36 Configuring Wireless Advanced Settings 4-37 Management Setup 4-39 Configuring Administrator Account 4-39 Configuring Management VLAN 4-40 Configuring SNMP 4-41 Configuring Backup/Restore Settings 4-43 Configuring Firmware Upgrade 4-44 Configuring System Time 4-45 Configuring Wi-Fi Schedule 4-46 Add a Schedule Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-46 Schedule Services Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47 T ABLE OF C ONTENTS V Configuring Command Line Interface 4-48 Configuring Logging 4-49 Configuring Diagnostics 4-50 Viewing Device Discovery 4-51 Configure Denial of Service Protection 4-52 Logging Out 4-53 Appendix A Federal Communication Commission Interference Statement A-1 Appendix B Industry Canada Statement B-1 Appendix C WorldWide Technical Support C-1 C ONVENTIONS VI ConventionsThe following conventi ons are used to give the user additional information about specific procedur es or content. It is important to pay attention to these conventions as they provide informa- tion to prevent dam age to equipment or personal injury. General ConventionsThe following general conventions are used in this document. N/A: Indicates that a component or a procedure is not applica- ble to this model. Prerequisite: Indicates a requirement that must be addressed before proceeding with the current function or procedure. CAUTION! CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES . CAU - TIONS APPEAR IN CAPITAL LETTERS TO EMPHASIZE THAT THE MESSAGE CONTAINS VITAL HEALTH AND SAFETY INFORMATION . WARNING! Warning information appears before the text it references to emphasize that the content may prevent damage to the device or equipment. Important: Indicates informat…

Text truncated - open the document above for the full version.

B ASIC N ETWORK S ETTINGS D YNAMIC IP 4-13 Secondary DNS Enter the secondar y DNS server address. Discard Ping on WAN Check to Enable to recognize pi ngs on the ENS500EXT WAN interface or Disable to blo ck pings on the ENS500EXT WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid. Blocking pings pr ovides some extra se curity from hackers. Click Accept to save the settings or Cancel to discard changes. Dynamic IPDynamic IP addressing a ssigns a different IP address each time a device connects to an ISP service provider. The service is most commonly used by ISP cable providers.Account Name Enter the account name provided by your ISP.Domain Name Enter the dom ain name provided by your ISP.MTU The maximum trans mission unit (MTU) specifies the largest packe t size permitted for an internet transmission. T he factory default MTU size for static IP is 1500. The MTU size can be set between 512 and 1500.Get Automatically From ISP Click the radio but ton to obtain the DNS automati cally from the DHCP server. Use These DNS Servers Click the radio button to set up the Primary DNS and Secondary DNS servers manually. Discard Ping on WAN Check to Enable to recognize pi ngs on the ENS500EXT WAN interface or Disable to blo ck pings on the ENS500EXT WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid. Blocking pings pr ovides some extra se curity from hackers. Click Accept to save the settings or Cancel to discard changes. B ASIC N ETWORK S ETTINGS P OINT - TO -P OINT P ROTOCOL OVER E THERNET (PPP O E) 4-14 Point-to-Point Protocol over Ethernet (PPPoE)Point-to-Point Protocol over Ethernet (PPPoE) is used mainly by ISPs that provide DSL modems to connect to the Internet.MTU Enter the maximum tran smission unit (MTU). The MTU specifies the largest packet size permitted for an internet transmission (PPPoE default: 1492). The MTU size can be set between 512 and 1492.Login Enter the username assigned by an ISP. Password Enter the password assigned by an ISP.Service Name Enter the service name of an ISP (optional).Connect on Demand Select the radio button to specify the maximum idle time. Internet connection will disconnect when it reach the maximum idle time, but it wil l automatically connect when user tries to acce ss the network. Keep Alive Select whether to keep the Internet connection always on, or enter a redial period on ce the internet lose connection. Get Automatically From ISP Click the radio but ton to obtain the DNS automati cally from the DHCP server. Use These DNS Servers Click the radio button to set up the Primary DNS and Secondary DNS servers manually. Discard Ping on WAN Check to Enable to recognize pi ngs on the ENS500EXT WAN interface or Disable to blo ck pings on the ENS500EXT WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid. Blocking pings pr ovides some extra se curity from hackers. Click Accept to save the settings or Cancel to discard changes. B ASIC N ETWORK S ETTINGS P OINT - TO -P OINT T UNNELLING P ROTOCOL (PPTP) 4-15 Point-to-Point Tunnelling Protocol (PPTP)The point-to-point tunnellin g protocol (PPTP) is used in association with virtual priv ate networks (VPNs). There a two part s to a PPTP connection: the WAN interface settings and the PPTP settings. MTU Enter the maximum tran smission unit (MTU). The MTU specifies the largest packet size permitted for an internet transmission (PPPoE default: 1492). The MTU size can be set between 512 and 1492.IP Address Enter the router’s WAN IP address. Subnet Mask Enter the router’s WAN subnet IP address.Default Gateway Enter the router’s WAN gateway IP address.PPTP Server Enter the IP ad dress of the PPTP server.Username Enter the usernam e provided by your ISP.Password Enter the password provided by your ISP. Connect on Demand If you want the ENS500EXT to e nd the Internet con nection after it has been inactive for a period of time, select this option and enter the number of minutes you want that peri od of inactivity to last. Keep Alive If you want the ENS500EXT to periodically check your Internet connection, select this option. Then specify how often you want the ENS500EXT to check the Internet co nnection. If the co nnection is down, the ENS500EXT automatically re-establishes your connectionGet Automatically From ISP Obtains the DNS automa tically from DHCP server. B ASIC N ETWORK S ETTINGS P OINT - TO -P OINT T UNNELLING P ROTOCOL (PPTP) 4-16 Use These DNS Servers Click the radio button to set up the Primary DNS and Secondary DNS servers manually. Discard Ping on WAN Check to Enable to recognize pi ngs on the ENS500EXT WAN interface or Disable to blo ck pings on the ENS500EXT WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid. Blocking pings pr ovides some extra se curity from hackers. Click Accept to save the settings or Cancel to discard changes. B ASIC N ETWORK S ETTINGS C ONFIGURING LAN S ETTINGS 4-17 4.3.2 Configuring LAN SettingsIP Address Enter the LAN IP address. IP Subnet Mask Enter the LA N IP subnet mask. Use Router As DHCP Server Check this opt ion to enable the ENS500EXT internal DHCP server.Starting IP Address Specify the starting IP address range for the pool of allocated for private IP addre sses. The starting IP address must be on the same subnet as the ending IP address; that is the first thr ee octets specified here must be the same as the first three octets in End IP Address.Ending IP Address Specify the ending IP address range for the pool of allocated for private IP addresses. The ending IP address must be on the same subn et as the starting IP address; that is the first three octets specified here must be the same as the first three octets in Start IP Address.WINS Server IP Enter the IP address of the WINS server. Click Accept to confirm the changes or…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 7 Page 8 Page 9 Page 10

Label location

Page 4 Page 5 Page 6

FCC ID: A8J-ENS500 Report No.: RF130107C03 Operational Description This device is a LONG RANGE WIRELESS 11N OUTDOOR AP/CB, which operates in 5GHz band; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 6Mbps data rate with OFDM technique will be applied. The transmitter of the EUT is powered by the 24Vdc from POE. The EUT is used Dipole antenna with RSMA connector. The other instruction, please have a look at the users manual.

Report No.: SA130107C03 1 of 5 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA130107C03 MODEL NO.: ENS500, ENS500EXT FCC ID: A8J-ENS500 RECEIVED: Jan. 07, 2013 TESTED: Jan. 08 ~ Jan. 12, 2013 ISSUED: Jan. 16, 2013 APPLICANT: EnGenius Technologies ADDRESS: 1580 Scenic Avenue, Costa Mesa, CA92626 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. Report No.: SA130107C03 2 of 5 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................ 4 2. RF EXPOSURE .............................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................ 5 2.2 MPE CALCULATION FORMULA ................................................................................... 5 2.3 CLASSIFICATION .......................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ................................. 5 Report No.: SA130107C03 3 of 5 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130107C03 Original release Jan. 16, 2013 Report No.: SA130107C03 5 of 5 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 22cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 Calculation result of maximum conducted power FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 5745-5825 29.80 8.01 22 0.993 1 NOTE: Directional gain = 5dBi + 10log(2) = 8.01dBi

Report No.: RF130107C03 1 of 49 Report Format Version 5.1.0 FCC TEST REPORT (15.247) REPORT NO.: RF130107C03 MODEL NO.: ENS500 (Please refer to item 3.1 for more details) FCC ID: A8J-ENS500 RECEIVED: Jan. 07, 2013 TESTED: Jan. 08 ~ Jan. 12, 2013 ISSUED: Jan. 16, 2013 APPLICANT: EnGenius Technologies ADDRESS: 1580 Scenic Avenue, Costa Mesa, CA92626 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130107C03 2 of 49 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ......................................................................................... 4 1. CERTIFICATION ...................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 6 3. GENERAL INFORMATION ...................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................ 7 3.2 DESCRIPTION OF TEST MODES .......................................................................... 9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 10 3.3 DESCRIPTION OF SUPPORT UNITS .................................................................. 12 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 12 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 13 4. TEST TYPES AND RESULTS ............................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ............. 14 4.1.2 TEST INSTRUMENTS ........................................................................................... 15 4.1.3 TEST PROCEDURES ........................................................................................... 16 4.1.4 DEVIATION FROM TEST STANDARD.................................................................. 16 4.1.5 TEST SETUP ......................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS .......................................................................... 17 4.1.7 TEST RESULTS .................................................................................................... 18 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................ 27 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 27 4.2.2 TEST INSTRUMENTS ........................................................................................... 27 4.2.3 TEST PROCEDURES ........................................................................................... 28 4.2.4 DEVIATION FROM TEST STANDARD.................................................................. 28 4.2.5 TEST SETUP ......................................................................................................... 28 4.2.6 EUT OPERATING CONDITIONS .......................................................................... 28 4.2.7 TEST RESULTS .................................................................................................... 29 4.3 6DB BANDWIDTH MEASUREMENT .................................................................... 31 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT ................................................. 31 4.3.2 TEST SETUP ......................................................................................................... 31 4.3.3 TEST INSTRUMENTS ........................................................................................... 31 4.3.4 TEST PROCEDURE .............................................................................................. 31 4.3.5 DEVIATION FROM TEST STANDARD.................................................................. 31 4.3.6 EUT OPERATING CONDITIONS .......................................................................... 31 4.3.7 TEST RESULTS .................................................................................................... 32…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST