A8QMPL-101Marco Polo Locator

1 Locator Model ETP-LOC-01 Tag Model ETP-TAG-01 Operating Instructions 2 Copyright © 2011 Eureka Technology Partners, LLC AL L RIGHTS RESERVED Protected under the following US and Foreign Patent s: US 6,788,199 US 7,148,801 CA 2438172 AU 2002255750 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not c ause harmful interference, and (2) this device must accept any interference receiv ed, including interference that may cause undesired operation. Changes or modificat ions not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule s. These limits are designed to provide reasonable protection against harmful inter ference in a residential installation. This equipment generates, uses and ca n radiate radio frequency energy and, if not installed and used in accordance with t he instructions, may cause harmful interference to radio communications. However, ther e is no guarantee that interference will not occur in a particular install ation. If this equipment does cause harmful interference t o radio or television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct the interference by on e or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment an d receiver. -- Connect the equipment into an outlet on a circui t different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV te chnician for help. This device complies with Industry Canada license-e xempt RSS standard(s). Operation is subject to the following two condition s: (1) this device may not cause interference, and (2) this device must accept any i nterference, including interference that may cause undesired operation of the device. Cet appareil s’accorde avec Industrie Canada licenc e-exempte RSS standard. (1) cet appareil ne peut pas causer l’intervention, et (2) cet appareil doit accepter de l’intervention, y compris l’intervention qui peut c auser l’opération non désirée de This Class 【 B 】 digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Marco Polo Operating Instructions 1 Disclaimers The Marco Polo system (the Product) is intended to be used as a supplement to the normal precautions a pet owner would take to en sure the safety of their pets. This Product is not a substitute for proper fencing , use of leashes, tie-outs or any other measures typically used to restrain pets and keep them out of harm’s way. If you are a new pet owner you should seek the advice of a trained professional regarding the proper enclosure and env ironment for your pet. Eureka Technology Partners, LLC makes no warranties regarding loss of property or personal injury, even if the loss was d ue to a malfunction of the Product. This Product is not intended for use on people or f or any purpose where injury or loss of life may result from the use or misuse o f the Product. Marco Polo Operating Instructions 2 User Controls and Displays Locator: Power Button – Turns the Locator on and off. Pet Buttons – One button for each of up to 3 pets. Pressing button changes the mode for that pet’s tag from Idle to Track to Monitor. Up Button – Moves the selection cursor up one position. Select Button – Selects the item currently flashing. Down Button - Moves the selection cursor down one position. Tag: Power Button – Hold down to turn power On/Off. LED on steady means the tag is turning off . 1, 2 or 3 flashes indicates battery level and that the tag is turning on. Status LED – Indicates On and Off status and battery charging status. Down Select Power Button Status LED Up Pet Buttons 1 2 3 Power Button Marco Polo Operating Instructions 3 System Setup Battery Charging The Marco Polo pet monitoring and tracking system c onsists of two parts: a handheld “Locator” unit and up to three “Tag” units that can be attached to your pet’s collar. Prior to first use, the internal lithium-ion rechargeable batteries must be charged with the included battery charger adapter. Also, if the battery is ever removed from the locator , the charger must be connected at least momentarily to reset it. Figure 3 shows the l ocation of the charging jacks. Battery Status Tag Low Battery Indicator Alarm Settings Boundary Settings Tag Mode Indicators Mode Box Setup Selections Status Messages Directional Arrows Distance Pe rcentage Signal Strength Bars Search Indicator Figure 2 Locator Display Elements Marco Polo Operating Instructions 4 When charging the tag’s battery, the tag’s status L ED will flash until the charge cycle is complete and then the LED will go o ff. The tag will not function while charging is in progress. When charg ing the locator, the locator’s battery status indicator will show the ch arge level increasing during the charge cycle and then the indicator will show f ull when the charging is complete. The locator can be used in any mode while connected to the charger. Tag Attachment To attach the tag to your pet’s collar, place the h ooked end of the collar clip against the top edge of the collar and press down f irmly until the collar is all the way inside the clip as shown in Figure 4. Charging Jacks Figure 3 Location of Charging Jacks Marco Polo Operating Instructions 5 When attaching the tag to a collar, always select t he side of the collar’s buckle that is way from the D-ring for holding license and ID tags. The best arrangement is to have the D-ring on the left, buck le in the center and the Marco Polo tag on the right (turn the collar over i f necessary to get this arrangement.) If the collar is an adjustable type t hen the side away from the D- ring may hav…

Text truncated - open the document above for the full version.

I @ I Eureka Technology Partners, LLC Authoritv to Act as Agent Request for Confidentialitv Date: Dccember 14.20 ll Sub.iect: Confidentiality Request for: A8QMPL-l 0l Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP- 100. Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit I Short'ferrn ffi Pennanent Block Diagrams External Photos ! Short Terrn f Slrort Term l-l Permanent*' Internal Photos ! Short Term I Permanent Operation Description/Theory of Operation f] Shofi Term fl Pennanent Pafis List & Placenrent/BOM [] Short Term f] Permanent Tune-Up Procedure f Short'l'errrr I Permanent Schematics ! Short 1'errn Test SetuP Plrotos I Short Term ! Permanent* LJser's Manual *Notc: Er-rreka'l'echnology Partners, LLC has spent substantial eflbrf in developing this product and it is one of the tlrst ol'its kind in indr-rstry. Having the subject infonnation easily available to "competition" u'oulcl negate the advantage they have achieved by developing this product. Not protecting the details of the desi-un will resr-rlt in financial hardship. Permanent Confidentiality: 'l'he applicant reqLlests the exhibits listed above as pennanently contidential be permarrently withheld fi'orn pLrblic review due to materials that contain trade secrets and proprietary intbrrnation not custornarill, released to tlre public. Short-Term Confi dentiality: 'fhe applicant reqLrests the exhibits selected above as short term confidential be withheld frorn public viery ibr a periocl of (specify number of )r- days from the date of the Crant of EqLriprnent Ar-rthorization and prior to marketing. This is to avoid premature release of scnsitive information prior to marketing or release of the product to the public. Applicant is also aq,are that they are responsible to notify ACB in the event information regarding the product or the prodLrct is rnade available to the pLrblic. ACB will then release the documents listed above for pLrblic disclosure pursuant to FCC Public Notice DA 04-1705. I - The asterisked items (*) require further justification before permanent confidentiality will be allowed. l-hese also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Furlher justification should be added to the note above. One such example for a potted device would be: "The EUT is FULLY potted using a non-removable epoxy based ntaterial. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting." .-P|easeret-ertob|tp'l'-itqhq{n','s'qLr.]dqqun.]'9 t'orrlldcntialiS,pdl for complete details. Eureka TechnologY Partners, LLG 5519 Paseo Gilberto, Yorba Linda, CA, 92886, Tel.714 693-8803 @ I NOTE for Industry Canada Applications: The applicant r-rnderstands that until such time that IC distinguishes between Shofi Terrn and Permanent Confidentiality, either type of rnarked exhibit above will sirnply be marked Confidential rvhen subrnitted to IC. Sincerely', Ily : .t r.r ur .'- .14) t"' - -"..- t1r" -. --. Timothy Crabtree (Prini name) Eureka Technology Partners, LLC 55'19 Paseo Gilberto, Yorba Linda, CA, 92886, Tel.714 693-8803

1 Photographs - EUT Constructional Details Test Model No.: ETP-LOC-01

Marco Polo Locator Model: ETP-LOC-01 Eureka Technology Partners, LLC FCC ID: A8QMPL-101 IC: 10078A-MPL101 Made in China 30.5 mm 10.5 mm Marco FCC ID Label Dimensions and Materials PN: ETP-LOCID-01 Rev NC 12-28-2011 Self Adhesive Mylar Flim Label 3 mil Facestock 1.8 mil Adhesive 3M 350 or equivalent Black Printing on Sliver Background

1 Photographs - EUT Constructional Details Test Model No.: ETP-LOC-01

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Nanshan District, Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Page: 1 of 1 FCC ID: A8QMPL-101 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1.1 RF Exposure Compliance Requirement 1.1.1 Standard requirement 15.247(b)(4) requirement: (4) The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section. if transmitting antennas of directional gain greater than 6 dBi are used. the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1). (b)(2). and (b)(3) of this section. as appropriate. by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 1.1.2 EUT RF Exposure The Max Conducted Peak Output Power is 18.84dBm(76.56mW) in lowest channel; The best case gain of the antenna is 2.0dBi. 2.0dB logarithmic terms convert to numeric result is nearly 1.585 According to the formula. calculate the EIRP test result: EIRP= P x G = 76.56mW x 1.585 = 121.348mW ① Hand SAR requirement: S= = 1054mW ② ; Body SAR requirement: S= = 316.228mW ③; ① < ②. ① < ③. So the SAR report is not required.

SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM111200545901 Page: 1 of 41 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover Page FCC REPORT Application No: SZEM1112005459RF Applicant: Eureka Technology Partners, LLC Product Name: Marco Polo Locator Operation Frequency: 902.700586MHz-906.600586MHz FCC ID: A8QMPL-101 Standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247: 2010 Date of Receipt: 2011-12-26 Date of Test: 2012-02-23 to 2012-02-28 Date of Issue: 2012-03-02 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM111200545901 Page: 2 of 41 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents Page 1 COVER PAGE.........................................................................................................................................................1 2 CONTENTS.............................................................................................................................................................. 2 3 TEST SUMMARY.................................................................................................................................................... 3 4 GENERAL INFORMATION................................................................................................................................... 4 4.1 CLIENT INFORMATION.......................................................................................................................................... 4 4.2 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................................... 4 4.3 E.U.T OPERATION MODE...................................................................................................................................... 6 4.4 DESCRIPTION OF SUPPORT UNITS......................................................................................................................... 6 4.5 TEST FACILITY..................................................................................................................................................... 7 4.6 TEST LOCATION................................................................................................................................................... 7 4.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER........................................................................................ 7 4.8 TEST …

Text truncated - open the document above for the full version.

1 Photographs-test setup photo (Test Model No.: ETP-LOC-01) Radiated Emission Conducted Emission