A8QMPT-101Marco Polo Tag

1 Locator Model ETP-LOC-01 Tag Model ETP-TAG-01 Operating Instructions 2 Copyright © 2011 Eureka Technology Partners, LLC AL L RIGHTS RESERVED Protected under the following US and Foreign Patent s: US 6,788,199 US 7,148,801 CA 2438172 AU 2002255750 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not c ause harmful interference, and (2) this device must accept any interference receiv ed, including interference that may cause undesired operation. Changes or modificat ions not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule s. These limits are designed to provide reasonable protection against harmful inter ference in a residential installation. This equipment generates, uses and ca n radiate radio frequency energy and, if not installed and used in accordance with t he instructions, may cause harmful interference to radio communications. However, ther e is no guarantee that interference will not occur in a particular install ation. If this equipment does cause harmful interference t o radio or television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct the interference by on e or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment an d receiver. -- Connect the equipment into an outlet on a circui t different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV te chnician for help. This device complies with Industry Canada license-e xempt RSS standard(s). Operation is subject to the following two condition s: (1) this device may not cause interference, and (2) this device must accept any i nterference, including interference that may cause undesired operation of the device. Cet appareil s’accorde avec Industrie Canada licenc e-exempte RSS standard. (1) cet appareil ne peut pas causer l’intervention, et (2) cet appareil doit accepter de l’intervention, y compris l’intervention qui peut c auser l’opération non désirée de This Class 【 B 】 digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Marco Polo Operating Instructions 1 Disclaimers The Marco Polo system (the Product) is intended to be used as a supplement to the normal precautions a pet owner would take to en sure the safety of their pets. This Product is not a substitute for proper fencing , use of leashes, tie-outs or any other measures typically used to restrain pets and keep them out of harm’s way. If you are a new pet owner you should seek the advice of a trained professional regarding the proper enclosure and env ironment for your pet. Eureka Technology Partners, LLC makes no warranties regarding loss of property or personal injury, even if the loss was d ue to a malfunction of the Product. This Product is not intended for use on people or f or any purpose where injury or loss of life may result from the use or misuse o f the Product. Marco Polo Operating Instructions 2 User Controls and Displays Locator: Power Button – Turns the Locator on and off. Pet Buttons – One button for each of up to 3 pets. Pressing button changes the mode for that pet’s tag from Idle to Track to Monitor. Up Button – Moves the selection cursor up one position. Select Button – Selects the item currently flashing. Down Button - Moves the selection cursor down one position. Tag: Power Button – Hold down to turn power On/Off. LED on steady means the tag is turning off . 1, 2 or 3 flashes indicates battery level and that the tag is turning on. Status LED – Indicates On and Off status and battery charging status. Down Select Power Button Status LED Up Pet Buttons 1 2 3 Power Button Marco Polo Operating Instructions 3 System Setup Battery Charging The Marco Polo pet monitoring and tracking system c onsists of two parts: a handheld “Locator” unit and up to three “Tag” units that can be attached to your pet’s collar. Prior to first use, the internal lithium-ion rechargeable batteries must be charged with the included battery charger adapter. Also, if the battery is ever removed from the locator , the charger must be connected at least momentarily to reset it. Figure 3 shows the l ocation of the charging jacks. Battery Status Tag Low Battery Indicator Alarm Settings Boundary Settings Tag Mode Indicators Mode Box Setup Selections Status Messages Directional Arrows Distance Pe rcentage Signal Strength Bars Search Indicator Figure 2 Locator Display Elements Marco Polo Operating Instructions 4 When charging the tag’s battery, the tag’s status L ED will flash until the charge cycle is complete and then the LED will go o ff. The tag will not function while charging is in progress. When charg ing the locator, the locator’s battery status indicator will show the ch arge level increasing during the charge cycle and then the indicator will show f ull when the charging is complete. The locator can be used in any mode while connected to the charger. Tag Attachment To attach the tag to your pet’s collar, place the h ooked end of the collar clip against the top edge of the collar and press down f irmly until the collar is all the way inside the clip as shown in Figure 4. Charging Jacks Figure 3 Location of Charging Jacks Marco Polo Operating Instructions 5 When attaching the tag to a collar, always select t he side of the collar’s buckle that is way from the D-ring for holding license and ID tags. The best arrangement is to have the D-ring on the left, buck le in the center and the Marco Polo tag on the right (turn the collar over i f necessary to get this arrangement.) If the collar is an adjustable type t hen the side away from the D- ring may hav…

Text truncated - open the document above for the full version.

@ I Authority to Act as Agent Request for Confidentialitv Date: Decernber 14.20 I I SLrb.ject: Confidentiality Reqr-rest for: A8QMPT-l 0 I Pursuant to FCC 47 CRF 0.457(d) and 0.459 and lC RSP-100. Section 10, the applicant requests that a part of the sr"rbject FCC application be lreld conf'idential. Type of Confidentiality Requested f Short Terrn I Perrnanent ! Shorr Terrn [] Short Terrn [] Permanent*r ! Short Terrn I Perrnanent ! Short Term f Perrnanent ! Slrort Term I Pennanent I Short Terrn I Permanent L_l Shofi l erm n Shoft Tenn I Permanent* Exhibit Block Diagrams E,xternal Photos Internal Plrotos Operation Description/Theory of Operatiort Parts List & PlacemenVBOM Tune-Up Procedure Schematics Test Setup Photos User's Manual *Note: [-Lrreka-fechnology Parlners. LLC has spent substantial efTort in developingthis prodr-rct and it is one ol'the tirst ol'its kind in industry. Having the subject infonnation easily available to "cotnpetition" u'ould ncgate the advantage they have achieved by developing this product. Not protecting the details ol'thc design will result in flnancial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be pennanently withheld fiom public review due to materials that contain trade secrets and proprietary information not custonrarily released to the pLrblic. Short-Term Confidentiality: The applicant requests the exhibits selected above as short tenn confidential be withheld fiom ptrblic vie* ibl a periodof (specify nlrmber o lr- days fiom the date of the Grant of EqLriprnent Ar-rthorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also auare tlrat they are responsible to notify ACB in the event information regarding the prodrrct or the procluct is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC PLrblic Notice DA 04-1705. r - The asrerisked iterns (*) require further-justification befbre permanent confidentiality will be allowed. 'l'hese also currently require review by the FCC under their Permit-But-Ask policy befbre the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such erample for a potted device would be: "The EUT is FULLY potted using a non-removable epoxy based ntaterial. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting." .-Pleasereferto|tttp,iiil.-qb!:e]:t.s.Ql.l-]]'dqcHn]9lll.$,.llliIt:-!'!!.q, tloirlltlcntiaiilr.pd{' for complete details. Eureka Technology Partners, LLC 5519 Paseo Gilberto Yorba Linda, CA.92886, fel714 693-8803 I @ I Eureka Technology Partners, LLC NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Perrnanent Confidentiality, either type of marked exhibit above will sinply be marked Confidential when subnritted to IC. Sincerell'. Br: .' , ._ u,". ,.--y'-/r+. :' . .? ( -- tl-1 , 1S igndftrre/Tit le') Timothy Crabtree (Print name) .-..l...;''-'l...i)l,li1.,..1i;1;1!iiitltlf()liti!".i Eureka Technology Partners, LLC 5519 Paseo Gilberto, Yorba Linda, CA, 92886, Tel.714 693-8803

1 Photographs - EUT Constructional Details Test model No.: ETP-TAG-01

Marco Polo Tag Model: ETP-TAG-01 FCC ID: A8QMPT-101 Made in Eureka Technology Partners, LLC IC: 10078A-MPT101 Li-ion China 26.6 mm 8.0 mm Marco Polo Tag Label Dimensions and Materials PN: ETP-TAGID-01 Rev A 12-28-11 Self Adhesive Mylar Flim Label 3 mil Facestock 1.8 mil Adhesive 3M 350 or equivalent Black Printing on Sliver Background

1 Photographs - EUT Constructional Details Test model No.: ETP-TAG-01

SGS-CSTC Standards Technical Services Co., Ltd . No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM111200546002 Page: 1 of 3 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 RF Exposure Evaluation declaration Application No.: SZEM1112005460RF Applicant: Eureka Technology Partners, LLC Address of Applicant: 5519 Paseo Gilberto Manufacturer: Mecca Holding (HK) Co., LTD Address of Manufacturer: Rm406, 4/F, Kinox Centre, 9 Hung To Road Kwun Tonq, KLN, HK Factory Mecca Manufacturing Co., Ltd. Address of Factory: Kong Yang Industrial Centre, Zhang Mu Tou Town, Dong Guan City, Guang Dong, China FCC ID: A8QMPT-101 Fundamental Carrier Frequency : 902.700586MHz -906.600586MHz Equipment Under Test (EUT): Name: Marco Polo Tag Model No.: ETP-TAG-01 Date of Receipt: 2011-12-26 Date of Test: 2012-02-23 to 2012-02-28 Date of Issue: 2012-03-01 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM111200546002 Page: 2 of 3 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 RF Exposure Evaluation 2.1 Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 300 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4* Pi * R 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM111200546002 Page: 3 of 3 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liabi…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM111200546001 Page: 1 of 41 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover Page FCC REPORT Application No: SZEM1112005460RF Applicant: Eureka Technology Partners, LLC Product Name: Marco Polo Tag Operation Frequency: 902.700586MHz -906.600586MHz FCC ID: A8QMPT-101 Standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247: 2010 Date of Receipt: 2011-12-26 Date of Test: 2012-02-23 to 2012-02-28 Date of Issue: 2012-03-01 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM111200546001 Page: 2 of 41 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents Page 1 COVER PAGE.........................................................................................................................................................1 2 CONTENTS.............................................................................................................................................................. 2 3 TEST SUMMARY.................................................................................................................................................... 3 4 GENERAL INFORMATION................................................................................................................................... 4 4.1 CLIENT INFORMATION.......................................................................................................................................... 4 4.2 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................................... 4 4.3 E.U.T OPERATION MODE...................................................................................................................................... 6 4.4 DESCRIPTION OF SUPPORT UNITS......................................................................................................................... 6 4.5 TEST FACILITY..................................................................................................................................................... 7 4.6 TEST LOCATION................................................................................................................................................... 7 4.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER........................................................................................ 7 4.8 TEST INS…

Text truncated - open the document above for the full version.

1 Photographs-test setup photo (Test model No.: ETP-TAG-01) Conducted Emission Radiated Emission