ACJ-HXWA30MWireless LAN Module

User’s manual Product: Wireless LAN Module Model: DWM-W092 FCC ID: ACJ-HXWA30M IC: 216A-HXWA30M For OEM integration only – device ca nnot be sold to general public. Therefore we will not supply the User’s manual, the installation manual is the offi cial for OEM. (Note) OEM integrators and end-users must be provided with specific information required to satisfy RF exposure compliance for the fin al host device. OEM integrators are instructed to ensure that the end us er has no manual instructions to remove or install the device. The antenna of this device must not be co-located or used in conjunction wi th any other antenna or transmitter. OEM integrators must be pro vided with antenna installation instructions. Only those antennas tested with the device or similar antennas with equal or lesser gain may be used with this transmitter. We will ask OEM to includ e the following Notices requ ired by FCC/ IC on th e product and in the User’s manual. ■ Requirement of Labeling (For FCC) Please describe the following item on the host device of the this module: Contains Transmitter Module FCC ID: ACJ-HXWA30M or Contains FCC ID: ACJ-HXWA30M This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (For IC) Please describe the following item on the host device of the this module: Contains Transmitter Module IC: 216A-HXWA30M or Contains IC: 216A-HXWA30M ■ Requirement of User’s Manual Statement (For FCC) User’s manual shall contain following sentence FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to oper ate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. When installing in Mobile device This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keep ing the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). When installing in Portable device This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR). * Portable device: Distance between the person's body and the antenna is 20cm or less. * Mobile device: Distance between the person's body and the antenna is more than 20cm. (For IC) Indicate the following information. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause unde sired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicabl es aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit acce pter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. * It can be also indicated on the equipment in place of the manual When installing in Mobile device This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permiss ive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte l es règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui es t considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets , pieds et chevilles). When installing in Portable device This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of spe cific absorption ratio (SAR). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte l es règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui es t considérée conforme sans évaluation du débit d’absorption spécifique (DAS).

Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division Letter of Agency October 24, 2012 AVG-12-U047 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan Re: Certification Application for WLAN Module, Model DWM-W092 FCC ID: ACJ-HXWA30M To Whom It May Concern: Please be advised Panasonic Corporation of North America hereby authorizes Yoshinobu Asai of Application Section, WiSE Japan, UL Verification Service, UL Japan, Inc to act on our behalf, as our agent. This shall include all matters related to FCC approval and any other lawful activity necessary to obtain such certification. Any acts carried out by them or UL Japan, Inc. relating to this application shall have the same effects as our own. This authorization shall expire one year from the date of this letter. If you have any questions regarding this authorization, please don’t hesitate to contact the undersigned. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. This application for equipment authorization has not been submitted to another TCB for certification. Product Name: WLAN Module, Model WM-W092 1 FCC ID: ACJ-HXWA30M FCC Rule Part: FCC Part 15, Subpart C, Section 15.247 Frequency Range: 2412 ~ 2462 MHz Equipment Class: Digital Transmission System / DTS Modular Type: Single Modular Approval Applicant & Grantee: Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 FRN Number: 0003762242 Thank you for your attention to this matter. Sincerely, Richard Mullen Richard Mullen Group Manager Product Safety & Compliance Division Cc: Isao Miyawaki, Team Leader / Technical Regulation Team Engineering Management Group Imaging Business Group, AVC Networks Company Panasonic Corporation 1 WLAN Module Model WM-W092 will be installed within host Panasonic Digital Camcorder, which will be separately authorized under Declaration of Conformity in accordance with FCC Part 15B Rules.

Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division Request for Single Modular Transmitter Approval October 24, 2012 AVG-12-U047 Re: Certification Application for WLAN Module, Model DWM-W092 FCC ID: ACJ-HXWA30M To Whom It May Concern: The WLAN Module, Model DMW-W092 is designed by Panasonic Corporation. This modular transmitter complies with the modular transmitters basic requirements in FCC Part 15 Subpart C Section 15.212 as indicated below and is intended to be installed within host Panasonic Digital Camcorder. Modular Transmitter Basic Requirements (1) Have its own RF shielding: This modular transmitter has its own RF shielding. Refer to the provided external photograph. (2) Have buffered modulation/data inputs: Data input to this modular transmitter is controlled as not generating excessive data speed and abnormal modulation. (3) Have its own power supply regulation: This modular transmitter has own power supply regulator. Please refer to the block diagram. (4) Comply with the antenna and transmission system requirements of § 15.203, 15.204(b) and 15.204(c): Antenna is permanently attached to the modular transmitter because it is print pattern antenna. This modular transmitter will always be used in the configuration in which it was authorized. (5) Tested in a stand-alone configuration: The modular transmitter has been performed the testing as a stand alone and then confirmed the compliance: Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in FCC § 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module. The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available: This modular transmitter complies with AC line conducted requirements. AC/DC power lines and data input/output lines does not contain ferrites, and the lengths of these lines are typical of actual use. All peripherals used during the testing are unmodified and commercially available. Please refer to the test report. Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division October 24, 2012 AVG-12-U047 (6) Equipped with either a permanently affixed label or must be capable of electronically displaying its FCC ID: FCC ID is shown on the label and permanently affixed to this modular transmitter. Please refer to the label drawing: If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module: If the FCC ID is not visible, FCC ID will also be displayed on the host device. Please refer to the installation manual. WLAN Module Model WM-W092 will be installed within host Panasonic Digital Camcorder. Panasonic Dual Camera Contains FCC ID: ACJ-HWA30M Contains IC: 216A-HXWA30M (7) Comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements: The necessary explanation to be complied with this requirement is contained in the manual. Please refer to the installation manual. (8) Comply with any applicable RF exposure requirements in its final configuration: The modular transmitter complies with FCC radiation exposure requirement. Refer to the RF Exposure/SAR Statement. Thank you for your attention to this matter. Sincerely, Richard Mullen Richard Mullen Group Manager Product Safety & Compliance Division

Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division Request for Confidentiality October 24, 2012 AVG-12-U047 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan Re: Certification Application for WLAN Module, Model DWM-W092 FCC ID: ACJ-HXWA30M To Whom It May Concern: Please be advised that the following information is to be held confidential on behalf of Panasonic Corporation of North America in accordance with provisions of Sections 0.457 and 0.459 of the Commission’s Rules; and Section 552(b)(4) of the Freedom of Information Act. This transmitter is not user adjustable and does not have user tune-up procedure. The below exhibits contain proprietary, confidential and/or trade secret materials, which would not be routinely made available for public inspection. • Schematic Diagram • Block Diagram • Parts List • Theory of Operation Thank you for your attention to this matter. Sincerely, Richard Mullen Richard Mullen Group Manager Product Safety & Compliance Division

Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division Request for Short-Term Confidentiality October 24, 2012 AVG-12-U047 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan Re: Certification Application for WLAN Module, Model DWM-W092 FCC ID: ACJ-HXWA30M To Whom It May Concern: Please be advised that the following information is to be held in confidence for 180 days 2 from the date of the Grant of Equipment Authorization and behalf of, Panasonic Corporation of North America, referring the FCC rules 0.457 and 0.459. The below exhibits contain pre-market information, which could give our competitors unfair advantage should this information be released before this product is actually introduced into the common marketplace. • External Photographs • Internal Photographs • Test Setup Photographs • User Manual Thank you for your attention to this matter. Sincerely, Richard Mullen Richard Mullen Group Manager Product Safety & Compliance Division 2 FCC Public Notice DA 04-1705 allows initial request for forty-five day short-term confidentiality and after that extensions may be requested.

Label Location Top Bottom

ＤＷＭ－Ｗ０９２ 内観写真 DWM-W092 Interior View

UL Japan, Inc. Head Office EMC Lab 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan T:: +81.596.24.8116 / F:: +81.596.24.8124 / W:: ul.com/jp October 11, 2012 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID: ACJ-HXWA30M To whom it may concern, We, UL Japan, Inc, hereby declare that Wireless LAN Module, model: DWM-W092 (FCC ID: ACJ-HXWA30M) of Panasonic Corporation of North America is exempt from RF exposure SAR evaluation as its output power meets the exclusion limits stated in FCC Part 2 §2.1093 and FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. Thank you for your attention to this matter. Sincerely, Masanori Nishiyama Manager of Head Office EMC Lab. WiSE Japan UL Verification Service UL Japan, Inc.

Test report No. : 33AE0098-HO-01-A Page : 2 of 55 Issued date : October 11, 2012 FCC ID : ACJ-HXWA30M UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ......................................................................................................... 3 SECTION 2: Equipment under test (E.U.T.) ........................................................................................... 3 SECTION 3: Test specification, procedures & results ............................................................................ 4 SECTION 4: Operation of E.U.T. during testing .................................................................................... 7 SECTION 5: Conducted Emission ............................................................................................................ 9 SECTION 6: Radiated Spurious Emission ............................................................................................ 10 SECTION 7: Antenna Terminal Conducted Tests ................................................................................ 11 APPENDIX 1: Data of EMI test .............................................................................................................. 12 Conducted Emission ......................................................................................................................... 12 6dB Bandwidth ................................................................................................................................. 13 Maximum Peak Output Power .......................................................................................................... 16 Average Output Power ...................................................................................................................... 19 Radiated Spurious Emission ............................................................................................................. 20 Conducted Spurious Emission .......................................................................................................... 27 Conducted Emission Band Edge compliance ................................................................................... 45 Power Density ................................................................................................................................... 46 99%Occupied Bandwidth ................................................................................................................. 50 APPENDIX 2: Test instruments ............................................................................................................. 52 APPENDIX 3: Photographs of test setup ............................................................................................... 53 Conducted Emission ......................................................................................................................... 53 Radiated Spurious Emission ............................................................................................................. 54 Worst Case Position (Horizontal: X-axis/ Vertical:Y-axis) .............................................................. 55 Test report No. : 33AE0098-HO-01-A Page : 3 of 55 Issued date : October 11, 2012 FCC ID : ACJ-HXWA30M UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 SECTION 1: Customer information Company Name : Panasonic Corporation of North America Address : One Panasonic Way 4B-8 Secaucus, NJ 07094 U.S.A Telephone Number : +1-201-348-7758 Facsimile Number : +1-201-392-4564 Contact Person : Richard Mullen SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Wireless LAN Module Model No. : DWM-W092 Serial No. : Refer to Section 4, Clause 4.2 Rating : DC 3.3V Receipt Date of Sample : September 17, 2012 Country of Mass-production : Philippines Condition of EUT : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No Modification by the test lab 2.2 Product Description General Specification Clock frequency(ies) in the system : 26MHz Radio Specification of WLAN (IEEE802.11b/g/n) Radio Type : Transceiver Frequency of Operation : 2412-2462MHz Modulation : DSSS and OFDM Power Supply (radio part input) : DC3.3V (Digital part), DC1.6V (RF Core), DC1.2V (Digital part) Antenna type : 2.4GHz Pattern Antenna Antenna Gain : 0.41dBi Test report No. : 33AE0098-HO-01-A Page : 4 of 55 Issued date : October 11, 2012 FCC ID : ACJ-HXWA30M UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 SECTION 3: Test specification, procedures & results 3.1 Test Specification Test Specification : FCC Part 15 Subpart C: 2012, final revised on August 13, 2012 and effective September 12, 2012 Title : FCC 47CFR Part15 Radio Frequency Device Subpart C Intentional Radiators Section 15.207 Conducted limits Section 15.247 Operation within the bands 902-928MHz, 2400-2483.5MHz, and 5725-5850MHz 3.2 Procedures and results Item Test Procedure Specification Worst margin Results Remarks Conducted Emission FCC: ANSI C63.4:2003 7. AC powerline Conducted Emission measurements FCC: Section 15.207 QP 29.6dB, 0.15000MHz, L AV 31.7dB, 0.15000MHz, N Complied - IC: RSS-Gen 7.2.4 IC: RSS-Gen 7.2.4 6dB Bandwidth FCC: "Guidance on Measurement of Digital Transmission Systems Operating under Section15.247" FCC: Section 15.247(a)(2) See data. Complied Conducted IC: RSS-Gen 4.6.2 IC: RSS-210 A8.2(a) Maximum Peak Output Power FCC: "Guidance on Measurement of Digital Transmission Systems Operating under Section15.247" FCC: Section 15.247(b)(3) Complied Conducted IC: RSS-Gen 4.8 IC: RSS-210 A8.4(4) Power Density FCC: "Guidance on Measurement of Digital Transmi…

Text truncated - open the document above for the full version.

Test report No. : 33AE0098-HO-01-A Page : 53 of 55 Issued date : October 11, 2012 FCC ID : ACJ-HXWA30M UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 APPENDIX 3: Photographs of test setup Conducted Emission Photo 1 Photo 2 Test report No. : 33AE0098-HO-01-A Page : 54 of 55 Issued date : October 11, 2012 FCC ID : ACJ-HXWA30M UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 Radiated Spurious Emission Photo 1 Photo 2 Test report No. : 33AE0098-HO-01-A Page : 55 of 55 Issued date : October 11, 2012 FCC ID : ACJ-HXWA30M UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 Worst Case Position (Horizontal: X-axis/ Vertical:Y-axis) X-axis Y-axis Z-axis End of Report