ACJ96NKX-HGC2002.4 GHz Wireless LAN Card

Model No. KX-HGC200 PLEASE READ BEFORE USE AND SAVE. Contents: Part Names . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Installation . . . . . . . . . . . . . . . 4 FCC and Other Information . . . . . . . . . . 6 OPERATING INSTRUCTIONS Panasonic World Wide Web address: http://www.panasonic.com for customers in the USA or Puerto Rico – 2 – Thank you for purchasing your new Panasonic wireless card. Attach your purchase receipt here. For your future reference Serial No. Date of purchase (found on the bottom of the unit) Name and address of dealer – 3 – Part Names ∫Part Names KX-HGC200 LINK ANT. READY Indicator – 4 – Hardware Installation To use the wireless network, inserting of the KX-HGC200 to the KX-HGW200 and to the computer(s) is needed. The KX-HGC200 can be inserted to the PCMCIA Type IIcard slot of a computer. 1 Insert the KX-HGC200 to the KX-HGW200. a:Make sure the power of the KX-HGW200 is off by checking the POWER indicator of the KX-HGW200. b:Open the cover on the front side of the KX-HGW200. c: Insert the KX-HGC200 to the card slot of the KX-HGW200 with the arrow mark on the KX-HGC200 pointing to the slot. d:Close the cover of the KX-HGW200. To remove the KX-HGC200 from the KX-HGW200, press the lever on the KX-HGW200 along with the card slot. Note: ≥Be sure to insert the KX-HGC200 fully. ≥Insert on the proper direction. When you feel resistance while inserting, turn the KX-HGC200 over and reinsert it. HomePNA WIRELESS ETHERNET INTERNET POWER KX-HGW200 KX-HGC200 LINK ANT. READY Arrow mark KX-HGW200 KX-HGC200 Card slot – 5 – 2 Insert the KX-HGC200 to the computer. a:Insert the KX-HGC200 to the PCMCIA Type IIslot of the computer with the arrow mark on the KX-HGC200 pointing to the slot. To remove the KX-HGC200 from the computer, press the lever on the computer along with the card slot. Note: ≥Be sure to insert the KX-HGC200 fully. ≥Insert on the proper direction. When you feel resistance when inserting, turn the KX-HGC200 over and reinsert it. KX-HGC200 LINK ANT. READY FCC and Other Information – 6 – This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. ≥Environment—do not place the unit in a room where the temperature is less than 5oC (41oF) or greater than 40oC (104oF). Allow 10 cm (4q) clearance around the unit for proper ventilation. Avoid excessive smoke, dust, mechanical vibration, shock, or direct sunlight. ≥Medical—consult the manufacturer of any personal medical devices, such as pacemakers, to determine if they are adequately shielded from external RF (radio frequency) energy. (The unit operates in the frequency range of 2401MHz to 2483MHz and the power output level is 0.1 watt.) Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF (radio frequency) energy. ≥Routine care—wipe the unit with a soft cloth. Do not use benzine, thinner, or any abrasive powder. Responsible Party:Matsushita Electric Corporation of America One Panasonic Way, Secaucus, NJ 07094 Tel No: 1-800-272-7033 For product service ≥Panasonic Servicenters are listed in the servicenter directory. ≥Call 1-800-211-PANA(7262) for the location of an authorized servicenter. ≥Panasonic’s e-mail address for customer inquiries: [email protected] for customers in the USA or Puerto Rico ONLY When you ship the product ≥Carefully pack your unit, preferably in the original carton. ≥Attach a letter, detailing the symptom, to the outside of the carton. Symptom ≥Send the unit to an authorized servicenter, prepaid and adequately insured. ≥Do not send your unit to the Panasonic Consumer Electronics Company listed on the next page or to executive or regional sales offices. These locations do not repair consumer products. – 7 – ≥This unit is designed for use in the United States of America. Sale or use of this product in other countries may violate local laws. ≥Ce appareil est conçu pour être utilisé aux États-Unis d’Amérique. La vente ou l’emploi de cet appareil dans certains autres pays peut constituer une infraction à la législation locale. ≥Esta unidad fue elaborada para uso en los Estados Unidos de América. La venta o el empleo de este producto en ciertos países puede constituir violación de la legislación local. Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America One Panasonic Way, Secaucus, New Jersey 07094 Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, In…

Text truncated - open the document above for the full version.

HGC200 PCMCIA CARD Block Diagram Kyushu Matsushita Electric Co.,Ltd. Panasonic VCO1 VCO2 Baseband Processor HFA3861B Tx I Tx Q Rx I Rx Q I/Q MOD/DEMOD PA RF2126 BPF HFA3783IN 748MHz UP/DOWN converter HFA3683AIN TX/RX SWITCH DA RF2324 XM2400LB -PM0601 LNA ENFVH1K2S81 SAW F NJG1506 BPF WhiteCap Controllor EPIC-M SDRAM Flash ROM 44MHz SYSTEM Clock BPF ENFVH172S80 B3677 LFSG20N27C2450B LFSG20N27C2450B BPF LFSG20N27C2 450B B69812-N2457- D501 MS136 EXT SW NJG1506 DIVERSITY SWITCH 2Mbit16Mbit Power Management +5V XC6366A185MR XC62FP4502MR XC62FP3302MR XC6366A335MR +1.8V(for EPIC-M core) +3.3V(for general) +3.3V(for synthesizer) +4.5V(for power) PCMCIA Interface ANTENNAS 1 2 34 5 6 7 8 9 10 11 12 13 14 151617 18 19 20 21 2223

EXHIBIT A FCC ID : ACJ96NKX-HGC200 GENERAL INFROMATION: Date Signaling Rate : 11Mbit/s Media Access Protocol : The protocol is a connection-oriented network protocol that Utilizes a dynamic time division multiple access (TDMA) Mechanism and DSSS , CSMA/CA(Collision Avoidance) For RF. Base-Band Modulation : Complementary Code Keying (CCK) 8bits/symbol (before spreading) Spread Spectrum : Direct Sequence with 11 chips/symbol interval. Pseudo random Barker code sequence: Chipping Rate: 11 Mchips/s Carrier Frequency : Selectable from factory pre-programmed set according to 2412 ~ 2462MHz (2412,2417,2422,2427,2432,2437,2442,2447,2452,2457 and 2462 MHz) RF Power Density : < 8 dBm/3kHz Antenna (indoors) : Omni-Dirrectional: - Polarization diversity. Spurious Emissions etc : Satisfies the USA Federal Comm. Commission (FCC) Rules Part 15.247

EXHIBIT C FCC ID: ACJ96NKX-HGC200 FCC ID: ACJ96NKX-HGC200 FCC ID: ACJ96NKX-HGC200 FCC ID: ACJ96NKX-HGC200 FCC ID: ACJ96NKX-HGC200

© 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card

FCC ID: ACJ96NKX-HGC200 EXHIBIT B FCC ID: ACJ96NKX-HGC200 MARKINGS

© 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card

EXHIBIT E FCC ID: ACJ96NKX-HGC200 DESCRIPTION OF ELECTRICAL CIRCUITRY TRANSMITTER: A) Baseband Processor.(5) During transmission, the data to be transmitted should be placed on the TX data line going into the Baseband processor. This data will be modulated CCK and then spread using a programmable PN code. B) Two signals will be generated (I & Q). The I & Q signals are sent to the Modulator/Demodulator(6) where they will be first filtered and then modulated with the IF frequency (374MHz). The IF oscillator(7) generates 748MHz which is divided by two inside the Modulator/Demodulator(6),so the final IF signal is 374MHz. C) Next, the two signals are combined into a single signal and sent over to the Up/Down converter(11). The Up/Down converter will shift this signal to the RF channel programmed in the synthesizer, in the 2.4GHz ISM band. D) In the final stage this signal is amplified to produce a typical power, measured in the middle of the ISM Band at the antenna RECEIVER: A) In the receive mode, the radio signal is received by one of the two external antennas(22,23). The antenna selected is option-ally determined by an Antenna Diversity algorithm in the Baseband Processor(5) which compares the quality of the received signal in each antenna during the Preamble and selects the better signal. This substantially improves the multipath performance of the assembly. Alternately, the antenna selection may be directly controlled by the software. B) The signal is amplified by the LNA(14), and then sent to the Up/Down converter(11). The Up/Down converter(11) down-converts this signal from the 2.4GHz range to the IF frequency, 374 MHz.. C) The Modulator/Demodulator(6) converts the signal to baseband and splits the signal into the In-Phase (I) and Quadrature (Q) components, before it is sent to the Baseband Processor. D) Finally, the Baseband Processor despreads and demodulates the data from CCK form, and places it on the RX data line. E) The RF and IF Local Oscillator signals are generated using the synthesizer and the voltage controlled oscillators. The synthesizer should be programmed with the desired RF channel frequency less the IF frequency. The Baseband processor and the synthesizer are driven from a common 44MHz oscillator(8) to control the timing of these chips.

© 2000 PCTEST Engineering Lab., Inc. PCTEST Engineering Laboratory, Inc. 66606660--B Dobbin Road B Dobbin Road •• Columbia, MD 21045 Columbia, MD 21045 •• U.S.A. U.S.A. TEL (410) 290TEL (410) 290--6652 6652 •• FAX (410) 290 FAX (410) 290--66546654 http://www.pctestlab.comhttp://www.pctestlab.com CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Matsushita Electric Industrial Co., Ltd. Dates of Tests: September 20, 2000 1006 Oaza Kadoma Test Report S/N: SAR.200918473.ACJ Kadoma, Osaka 571 JAPAN Test Site: PCTEST Lab, Columbia, MD Attention: K. Nawata (KMEICL) Rich Mullen (PSCD, MECA) FCC ID ACJ96NKX-HGC200 APPLICANT Matsushita Electric Industrial Co., Ltd. EUT Type: Wireless LAN Network Adapter Card (PCMCIA) Method/System: Direct Sequence System (DSS) Tx/Rx Frequency: 2412-2462 MHz Max. RF Output Power: 0.126W EIRP (20.99 dBm) Trade Name/Model(s): PANASONIC KX-HGC200 FCC Classification: Spread Spectrum Transceiver (DSS) Application Type: Certification FCC Rule Part(s): 2.1093; ET Docket 96.326 Max. SAR Measurement: 0.2495 mW/g Body SAR This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in ANSI/IEEE Std. C95.3-1992. (See Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. NVLAP accreditation does not constitute any product endorsement by NVLAP or any agency of the United States Government. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). 200918473.ACJ SAR Measurement Report FCC Part 15.247 Certification © 2000 PCTEST Lab i Table of Contents 1.1 SCOPE 1 2.1 INTRODUCTION / SAR DEFINITION 2 3.1 SAR MEASUREMENT SET-UP 3 4.1 ISOTROPIC E-FIELD PROBE SYSTEM 4 5.1 E-FIELD PROBE SYSTEM 5-6 6.1 PHANTOM & EQUIVALENT TISSUES 7 7.1 SYSTEM SPECIFICATIONS 8 8.1 MEASUREMENT PROCESS 9 9.1 TEST POSITION OF THE EUT 10 10.1 ANSI/IEEE C95.1 RF EXPOSURE LIMITS 11 11.1 MEASUREMENT UNCERTAINTIES 12 12.1 TEST DATA SUMMARY 13 13.1 SAR TEST EQUIPMENT LIST 14 14.1 CONCLUSION / REFERENCES 15 APPENDIX A – SAR TEST PLOTS 16 APPENDIX B – SAR TEST SETUP PHOTOGRAPHS 17 Test Report S/N: SAR.200918473.ACJ SAR Measurement Report Test Dates: September 20, 2000 FCC Part 15.247 Certification PANASONIC Spread Spectrum Wireless LAN Network Adapter Card (PCMCIA) © 2000 PCTEST Lab FCC ID: ACJ96NKX-HGC200 (Tx 2412-2462MHz) 1 Figure 1. SAR Test Set-up SAR MEASUREMENT REPORT 1.1 Scope Environmental evaluation measurements of specific absorption rate 1 (SAR) distributions in simulated human head and body tissues exposed to radiofrequency (RF) radiation from wireless portable devices for compliance with the rules and regulations of the U.S. Federal Communications Commission (FCC). 2 Applicant: Matsushita Electric Industrial Co., Ltd. Address: 1006 Oaza Kadoma Kadoma, Osaka 571 JAPAN Attention: K. Nawata (KMECL) Rich Mullen (PSCD, MECA) • EUT Type: Wireless LAN Network Adapter Card (PCMCIA) • FCC Rule Part(s): § 2.1093, Docket 96-326 • Trade Name: PANASONIC • FCC IDENTIFIER: ACJ96NKX-HGC200 • Model(s): KX-HGC200 • Tx/Rx Frequency: 2412 - 2462 MHz • Application Type: Certification • FCC Classification: Spread Spectrum Transceiver (DSS) • Max. RF Output Power: 0.126W EIRP (20.99 dBm) • Method/System: Direct Sequence System (DSS) • Dates of Tests: September 20, 2000 • Place of Tests: PCTEST Engineering Lab. Columbia, MD, U.S.A. • Report Serial No.: SAR.200918473.ACJ 1 Specific Absorption Rate (SAR) is a measure of the rate of energy absorption due to exposure to an RF transmitting source (wireless portable device). 2 IEEE/ANSI Std. C95.1-1992 limits are used to determine compliance with FCC ET-Docket 93-62. Test Report S/N: SAR.200918473.ACJ SAR Measurement Report Test Dates: September 20, 2000 FCC Part 15.247 Certification PANASONIC Spread Spectrum Wireless LAN Network Adapter Card (PCMCIA) © 2000 PCTEST Lab FCC ID: ACJ96NKX-HGC200 (Tx 2412-2462MHz) 2 2.1 INTRODUCTION The FCC has adopted the guidelines for evaluating the environmental effects of radiofrequency radiation in ET Docket 93-62 on Aug. 6, 1996 to protect the public and workers from the potential hazards of RF emissions due to FCC-regulated portable devices.[1] The safety limits used for the environmental evaluation measurements are based on the criteria published by the American National Standards Institute (ANSI) for localized specific absorption rate (SAR) in IEEE/ANSI C95.1-1992 Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. (c) 1992 by the Institute of Electrical and Electronics Engineers, Inc., New York, New York 10017.[2] The measurement procedure described in IEEE/ANSI C95.3-1992 Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields - RF and Microwave[3] is used for guidance in measuring SAR due to the RF radiation exposure from the Equipment Under Test (EUT). These criteria for SAR evaluation are similar to those recommended by the National Council on Radiation Protection and Measurements (NCRP) in Biological Effects and Exposure Criteria for Radiofrequency Electromagnetic Fields,” NCRP Report No. 86 (c) NCRP, 1986, Bethesda, MD 20814.[4] SAR is a measure of the rate of energy absorption due to exposure to an RF transmitting source. SAR values have been related to threshold levels for potential biological hazards. 2.2 SAR Definition Specific Absorption Rate (SAR) is defined as the time derivative (rate) of the incremental energy (dU) absorbed by (dissip…

Text truncated - open the document above for the full version.

© 2000 PCTEST Engineering Lab., Inc. PCTEST Engineering Laboratory, Inc. 66606660--B Dobbin Road B Dobbin Road •• Columbia, MD 21045 Columbia, MD 21045 •• U.S.A. U.S.A. TEL (410) 290TEL (410) 290--6652 6652 •• FAX (410) 290 FAX (410) 290--66546654 http://www.pctestlab.comhttp://www.pctestlab.com CERTIFICATE OF COMPLIANCE Matsushita Electric Industrial Co., Ltd. Dates of Tests: September 18-20, 2000 1006 Oaza Kadoma Test Report S/N: 15.200918468.ACJ Kadoma, Osaka 571 JAPAN Test Site: PCTEST Lab, Columbia MD Attention: K. Nawata (Kyushu MEICL) Rich Mullen (MECA-PSCD) FCC ID ACJ96NKX-HGC200 APPLICANT Matsushita Electric Industrial Co., Ltd. FCC Rule Part(s): § 15.247; ANSI C-63.4 (1992) Classification: Spread Spectrum Transceiver (DSS) Method/System: Direct Sequence System Equipment Type: Wireless LAN PCMCIA Card Max Output Power: 0.126 Watts Frequency Range: 2412 – 2462 MHz Trade/Model No(s).: Panasonic KX-HGC200 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C-63-4. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. 200918468.ACJ FCC Part 15.247 Certification © 2000 PCTEST Engineering Laboratory, Inc. FCC Part 15.247 TABLE OF CONTENTS SCOPE 1 INTRODUCTION (SITE DESCRIPTION) 2 PRODUCT INFORMATION 3 DESCRIPTION OF TESTS A. CONDUCTED EMISSIONS 4 B. RADIATED EMISSIONS 5 C. RESTRICTED BANDS 6 D. ANTENNA REQUIREMENT 7 E. DIRECT SEQUENCE BANDWIDTH 8 F. MAXIMUM PEAK POWER OUTPUT 9 G. POWER DENSITY 10 RADIATED MEASUREMENTS (FUNDAMENTAL & HARMONICS) 11-13 FREQUENCY MEASUREMENTS (SPURIOUS) 14 PROCESSING GAIN 15 LIST OF TEST EQUIPMENT 16 CONCLUSION 17 APPENDIX A - LABELLING REQUIREMENTS 18-19 APPENDIX B - PLOTS OF EMISSIONS 20 APPENDIX C - PHOTOGRAPHS OF TEST SET-UP 21 APPENDIX D - EUT PHOTOGRAPHS 22 APPENDIX E - USER’S MANUAL 23 Test Report S/N: 15.200918468.ACJ FCC Part 15.247 Dates of Tests: Sept. 18-20, 2000 Certification © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 Spread Spectrum Wireless LAN Network Adapter Card 1 MEASUREMENT REPORT Scope - Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission. §2983(a) General Information Applicant Name: Matsushita Electric Industrial Co., Ltd. Address: 1006 Oaza Kadoma Kadoma, Osaka 571 JAPAN Attention: K. Nawata (Kyushu MEICL) Rich Mullen (MECA-PSCD) • FCC ID: ACJ96NKX-HGC200 • Class: Spread Spectrum Transceiver (DSS) • Type: Wireless LAN Network Adapter Card (PCMCIA) • Freq. Range: 2412 – 2462 MHz • Method/System: Direct Sequence System (DSS) • Model No(s): KX-HGC200 • Max. RF Output Power: 0.126 W • Power Supply: 5VDC 850mA from Note Book PC • Rule Part(s): § 15.247 • Dates of Tests: September 18-20, 2000 • Place of Tests: PCTEST Lab, Columbia, MD U.S.A. • Test Report S/N: 15.200918468.ACJ Test Report S/N: 15.200918468.ACJ FCC Part 15.247 Dates of Tests: Sept. 18-20, 2000 Certification © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 Spread Spectrum Wireless LAN Network Adapter Card 2 INTRODUCTION The measurement procedure described in American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40GHz (ANSI C63.4-1992) and FCC Public Notice dated July 12, 1995 entitled “Guidance on Measurement for Direct Sequence Spread Spectrum Systems” were used in the measurement of Panasonic Spread Spectrum wireless LAN network adapter card. These measurement tests were conducted at PCTEST Engineering Laboratory, Inc. facility in New Concept Business Park, Guilford Industrial Park, Columbia, Maryland. The site address is 6660-B Dobbin Road, Columbia, MD 21045. The test site is one of the highest points in the Columbia area with an elevation of 390 feet above mean sea level. The site coordinates are 39° 11'15" N latitude and 76° 49'38" W longitude. The facility is 1.5 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. There are no FM or TV transmitters within 15 miles of the site. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4 on October 19, 1992. PCTEST Location The map at right shows the location of the PCTEST Lab, its proximity to the FCC Lab, the Columbia vicinity area, the Baltimore- Washington International (BWI) airport, and the city of Baltimore, and the Washington, D.C. area. (see Figure1). Figure 1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area. Test Report S/N: 15.200918468.ACJ FCC Part 15.247 Dates of Tests: Sept. 18-20, 2000 Certification © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 Spread Spectrum Wireless LAN Network Adapter Card 3 PRODUCT INFORMATION Equipment Description: The Equipment under test (EUT) is the Panasonic KX-HGC200 wireless LAN network adapter PCMCIA Card using spread spectrum direct sequence and time division duplex techniques. Frequency Range: 2412 – 2462 MHz Channels: 3 Channel Separation: 25.0 MHz Spread Spectrum Method: Direct Sequence (DBPSK modulation) Max RF Output Power: 0.126 Watts Antenna: Omni-directional Power Consumption: 5VDC 850mA from Note Book PC CH Rx/Tx Freq. (MHz) 01 2412 06 2437 11 2462 Test Report S/N: 15.200918468.ACJ FCC Part 15.247 Dates o…

Text truncated - open the document above for the full version.

© 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 1004310 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 1004310 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card © 2000 PCTEST Lab Panasonic FCC ID: ACJ96NKX-HGC200 NVLAP Lab Code: 100431-0 Spread Spectrum Wireless LAN Network Adapter Card