ACJ96NKX-TGCA35DECT 6.0 Handset

Installation Manual Additional Digital Cordless Handset Model No. KX-TGCA35 KX-TGHA20 KX-TGEA20KX-TGHA20 Thank you for purchasing a Panasonic product. This unit is an additional handset compatible with the following series of Panasonic Digital Cordless Phone: - KX-TGC350/KX-TGC360 (The corresponding models are subject to change without notice.) You must register this handset with your base unit before it can be used. This installation manual describes only the steps needed to register and begin using the handset. Please read the base unit’s operating instructions for further details. Please read this installation manual before using the unit and save it for future reference. For assistance, visit our Web site: http://shop.panasonic.com/support for customers in the U.S.A. Printed in Malaysia PNQX7767ZA PT1115MG0 Accessory information Supplied accessories Accessory item/Order numberQuantity Charger/PNLC1073ZB 1 Rechargeable batteries/HHR-4DPA2 Handset cover * 1 /PNYNTGCA35BR 1 * Note: RPlease read the base unit’s operating instructions for additional/replacement accessories. Setting up Connections/Wall mounting Connect the AC adaptor to the power outlet. Drive the screws ( 1 ) (not supplied) into the wall, if necessary. 2 27.2 mm (1 1 /16 inch e s) 12 2 1 2 For assistance, please visit http://shop.panasonic.com/support Installation 1 The handset cover comes attached to the handset. Note: RThe A C adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) RMake sure that the wall and the fixing method are strong enough to support the weight of the unit. Battery installation/Battery charging Impor t ant: RUse the supplied rechargeable batteries. For replacement, we recommend using the Panasonic rechargeable batteries noted on page 2. RUSE ONLY rechargeable Ni-MH batteries AAA (R03) size ( 1 ). RDo NOT use Alkaline/Manganese/Ni-Cd batteries. RConfirm correct polarities ( , ). Charg e for about 7 hours. RConfirm “Charging” is displayed ( 2 ). RWhen t he batteries are fully charged, “Fully charged” is displayed. 1 2 Note: RIf the batteries are fully charged, but the operating time seems to be shorter, clean the battery ends ( , ) and the charge contacts with a dry cloth and c h a r g e again. Registering a handset to a base unit 1Base unit: Press and hold M N for about 5 seconds. R If all registered handsets start ringing, press M N again to stop, then repeat this step. For assistance, please visit http://shop.panasonic.com/support 3 Installation 2Handset: Pl ace the handset on the base unit or charger, then wait until a long beep sounds and is displayed. No t e: RIf an error tone sounds, or if is displayed, register the handset according to t h e base unit’s operating instructions. Display language 1MME N UN (right soft key) #110 2MbN: Select the desired setting. a MSAVEN a MOFFN For your safety To prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection RCompletely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. RRegularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire. RUnplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact us at http://shop.panasonic.com/support Installation RTo prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. RDo not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. 4 For assistance, please visit http://shop.panasonic.com/support Installation CAUTION Installation and location RTh e AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. Battery RWe recommend using the supplied batteries or additional/replacement batteries noted on page 2 for replacement battery information. USE ONLY rechargeable Ni-MH batteries AAA (R03) size. RDo not mix old and new batteries. RDo not open or mutilate the batteries. Released electrolyte from the batteries is corrosive and may cause burns or injury to the eyes or skin. The electrolyte is toxic and may be harmful if swallowed. RExercise care when handling the batteries. Do not allow conductive materials such as rings, bracelets, or keys to touch the batteries, otherwise a short circuit may cause the batteries and/or the conductive material to overheat and cause burns. RCharge the batteries provided with or identified for use with this product only, in accordance with the instructions and limitations specified in this manual. ROnly use a compatible base unit (or charger) to charge the batteries. Do not tamper with the base unit (or charger). Failure to follow these instructions may cause the batteries to swell or explode. Attention: A nickel metal hydride battery that is re cyclable powers the product you have purchased. Please call 1-800-8-BATTERY (1-800-822-8837) for information on how to recycle this battery. Important safety instructions When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool. 2. Do not use the telephone to report a gas leak in the vicinity of the leak. For assistance, please visit http://shop.panasonic.com/support 5 Instal…

Text truncated - open the document above for the full version.

Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] Richard Mullen, Group Manager Product Safety and Compliance Department Power of Attorney December 8, 2015 PCTP-16-F005A Federal Communication Commission Equipment Authorization Division / Application Processing Branch 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern; Panasonic Corporation of North America hereby authorizes Nemko AS to act on our behalf in all matters relating to the preparation of TCB Certification application for the below described product, which are in compliance with FCC Part 15D. Any and all acts carried out by Nemko AS on our behalf shall have the same effects as acts of our own for a period of one year from the date of this letter. Type Filing: Original Application for DECT Cordless Telephone Handset, Model KX-TGCA35 Product Classification: Part 15 Unlicensed PCS Portable Tx Held to Ear (PUE) FCC ID Handset Unit ACJ96NKX-TGCA35 FCC Rule Part: FCC Part 15, Subpart D Frequency Range: 1921.536 ~ 1928.448 MHz Responsible Panasonic Corporation of North America Applicant & Grantee: Two Riverfront Plaza, 9 th Floor, Newark, NJ 07102-5490 Responsible Manufacturer: Panasonic System Networks Co., Ltd. Sincerely yours, Richard Mullen Group Manager Panasonic Corporation of North America Product Safety and Compliance Division Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] Richard Mullen, Group Manager Product Safety and Compliance Department Request for Confidentiality December 8, 2015 PCTP-16-F005A Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern; Type Filing: Original Application for DECT Cordless Telephone Handset, Model KX-TGCA35 Product Classification: Part 15 Unlicensed PCS Portable Tx Held to Ear (PUE) FCC ID Handset Unit ACJ96NKX-TGCA35 FCC Rule Part: FCC Part 15, Subpart D In accordance with provisions of Sections 0.457(d) and 0.459 of the Commission’s Rules and Section 552(b)(4) of the Freedom of Information Act, we request permanent confidentiality for exhibits, which contain: (1) Antenna Construction; (2) Description of Electrical Circuitry; (3) Schematic Diagrams of Handset Unit and RF Unit; and (4) Block Diagram. The transmitter is not user adjustable and does not have a Tune-Up Procedure. These exhibits contain proprietary, confidential and trade secrets material, which would not be routinely made available for public inspection. In accordance with FCC Public DA 04-1705, we request forty-five day short-term confidentiality, starting from the from the issuance of equipment authorization date, for exhibits, which contain: (1) External Photographs of Handset Unit and RF Unit; (2) Internal Photographs of Handset Unit and RF Unit; (3) Test Setup Photographs; and (4) User Manual. These exhibits contain pre-market information, which could give our competitors unfair advantage should this information be released before this product is actually introduced into the common marketplace. Sincerely yours, Richard Mullen Group Manager Panasonic Corporation of North America Product Safety and Compliance Division

EXTERNAL PHOTOGRAPHS KX-TGCA35 Top View Bottom View

EXHIBIT B MARKINGS Portable Unit: FCC ID Label (Nameplate) The marking will be shown on the battery compartment of the portable unit.

INTERNAL PHOTOGRAPHS Internal View Internal View 2 Bottom View

SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35 Page 1 of 26 The Testcenter facility ‘Dosimetric Test Lab’ within IMST GmbH is accredited by the German National ‘Deutsche Akkreditierungsstelle GmbH (DAkkS)’ for testing according to the scope as listed in the accreditation certificate: D-PL-12139-01-00. SAR Test Report Dosimetric Assessment of the Portable Device KX-TGCA35 from Panasonic (FCC ID: ACJ96NKX-TGCA35) According to the FCC Requirements December 9, 2015 IMST GmbH Carl-Friedrich-Gauß-Str. 2 - 4 47475 Kamp-Lintfort Germany Customer Panasonic System Networks Co., Ltd. 1 - 62, 4 - chome Minoshima, Hakata-ku, Fukuoka 812-8531 Japan The test results only relate to the items tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35 Page 2 of 26 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR Executive Summary The KX-TGCA35 is a new cordless phone (Portable Device) from Panasonic operating in the 1920 MHz -- 1930 MHz frequency range. The device has an integrated antenna and works in US DECT standard. The objective of the measurements done by IMST was the dosimetric assessment of one device in a worst case setup in head configuration. Since there was a special test software available, SAR tests were conducted with a specific channel and maximum output power during the measurement. The examinations have been carried out with the dosimetric assessment system „DASY4“. The measurements were made according to the 47 CFR § 2.1093 [47CFR] for evaluating compliance of mobile and portable devices with FCC limits for human exposure (general population) to radiofrequency emissions. Additional information and guidelines given by the following FCC documents were used:  SAR Measurement Requirements for 100 MHz to 6 GHz [KDB 865664 D01 v01r04]  Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies [KDB 447498 D01 v06] All measurements have been performed in accordance to the recommendations given by the system manufacturer SPEAG AG, Switzerland. SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35 Page 3 of 26 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR Compliance Statement The Panasonic KX-TGCA35 cordless phone (FCC ID: ACJ96NKX-TGCA35) is in compliance with the following standards for uncontrolled exposure:  47 CFR § 2.1093 [47CFR],  ANSI / IEEE C95.1-1999 [IEEE C95.1-1999] The maximum results of SAR for the KX-TGCA35 are as follows: Worst Case SAR Results Band Frequency [MHz] CH Phantom Configuration Fig. No. Plot No. Highest Reported SAR 1g [W/kg] SAR 1g Limit [W/kg]. US DECT 1924.992 2 Left Head Cheek 13 1 0.017 1.6 PASS Prepared by: ...................................... Reviewed by: ........................................ Dessislava Patrishkova Alexander Rahn Test Engineer Quality Assurance SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35 Page 4 of 26 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR Table of Contents SUBJECT OF INVESTIGATION ........................................................................................................................ 5 1 FCC EXPOSURE CRITERIA ..................................................................................................................... 5 1.1 DISTINCTION BETWEEN EXPOSED POPULATION, DURATION OF EXPOSURE AND FREQUENCIES ................ 6 1.2 DISTINCTION BETWEEN MAXIMUM PERMISSIBLE EXPOSURE AND SAR LIMITS ......................................... 6 2 THE FCC MEASUREMENT PROCEDURE .............................................................................................. 7 2.1 GENERAL REQUIREMENTS ................................................................................................................... 7 2.2 DEVICE OPERATING NEXT TO A PERSON’S EAR ..................................................................................... 7 2.2.1 PHANTOM REQUIREMENTS ............................................................................................................... 7 2.2.2 TEST POSITIONS ............................................................................................................................. 7 2.2.3 TEST TO BE PERFORMED ................................................................................................................. 9 3 THE MEASUREMENT SYSTEM ............................................................................................................. 10 3.1 PHANTOMS ........................................................................................................................................ 11 3.2 E-FIELD-PROBES ............................................................................................................................... 12 3.3 MEASUREMENT PROCEDURE .............................................................................................................. 13 3.4 UNCERTAINTY ASSESSMENT .............................................................................................................. 14 4 OUTPUT POWER VALUES AND TUNE-UP INFORMATION ............................................................... 15 5 SAR RESULTS ........................................................................................................................................ 15 6 APPENDIX ............................................................................................................................................... 16 6.1 ADMINISTRATIVE DATA ....................................................................................................................... 16 6.2 DEVICE UNDER TEST AND TEST CONDITIONS ...................................................................................... 16 6.3 TISSUE RECIPES ................................................................................................................................ 16 6.4 MATERIAL PARAMETERS .................................…

Text truncated - open the document above for the full version.

SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_CalData Page 1 of 20 The Testcenter facility ‘Dosimetric Test Lab’ within IMST GmbH is accredited by the German National ‘Deutsche Akkreditierungsstelle GmbH (DAkkS)’ for testing according to the scope as listed in the accreditation certificate: D-PL-12139-01-00. Appendix for the SAR Test Report Dosimetric Assessment of the Portable Device KX-TGCA35 from Panasonic (FCC ID: ACJ96NKX-TGCA35) According to the FCC Requirements Calibration Data December 9, 2015 IMST GmbH Carl-Friedrich-Gauß-Str. 2 - 4 47475 Kamp-Lintfort Germany Customer Panasonic System Networks Co., Ltd. 1 - 62, 4 - chome Minoshima, Hakata-ku, Fukuoka 812-8531 Japan

SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Plots Page 1 of 5 The Testcenter facility ‘Dosimetric Test Lab’ within IMST GmbH is accredited by the German National ‘Deutsche Akkreditierungsstelle GmbH (DAkkS)’ for testing according to the scope as listed in the accreditation certificate: D-PL-12139-01-00. Appendix for the SAR Test Report Dosimetric Assessment of the Portable Device KX-TGCA35 from Panasonic (FCC ID: ACJ96NKX-TGCA35) According to the FCC Requirements SAR Distribution Plots December 9, 2015 IMST GmbH Carl-Friedrich-Gauß-Str. 2 - 4 47475 Kamp-Lintfort Germany Customer Panasonic System Networks Co., Ltd. 1 - 62, 4 - chome Minoshima, Hakata-ku, Fukuoka 812-8531 Japan The test results only relate to the items tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Plots Page 2 of 5 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR SAR Distribution Plots for Head Configuration Test Laboratory: IMST GmbH, DASY Yellow (II); File Name: TGCA35_yplm_1.da4 DUT: Panasonic; Type: KX-TGCA35; Serial: SA35BS1128 Program Name: DECT Communication System: DECT Handset; Frequency: 1924.99 MHz;Duty Cycle: 1:24 Medium parameters used: f = 1925 MHz; σ = 1.41 mho/m; ε r = 40.8; ρ = 1000 kg/m 3 Phantom section: Left Section DASY4 Configuration: - Probe: ET3DV6R - SN1669; ConvF(4.97, 4.97, 4.97); Calibrated: 2/19/2015 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 2/19/2015 - Phantom: SAM 1340; Type: QD 000 P40 CB; Serial: TP-1340 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Cheek Left/Area Scan (7x14x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.015 mW/g Cheek Left/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.64 V/m; Power Drift = -0.114 dB Peak SAR (extrapolated) = 0.025 W/kg SAR(1 g) = 0.014 mW/g; SAR(10 g) = 0.00904 mW/g Fig. 1: SAR distribution for DECT US, channel 2, cheek position, left side of head (December 8, 2015) SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Plots Page 3 of 5 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR Test Laboratory: IMST GmbH, DASY Yellow (II); File Name: TGCA35_yplm_2.da4 DUT: Panasonic; Type: KX-TGCA35; Serial: SA35BS1128 Program Name: DECT Communication System: DECT Handset; Frequency: 1924.99 MHz;Duty Cycle: 1:24 Medium parameters used: f = 1925 MHz; σ = 1.41 mho/m; ε r = 40.8; ρ = 1000 kg/m 3 Phantom section: Left Section DASY4 Configuration: - Probe: ET3DV6R - SN1669; ConvF(4.97, 4.97, 4.97); Calibrated: 2/19/2015 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 2/19/2015 - Phantom: SAM 1340; Type: QD 000 P40 CB; Serial: TP-1340 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Tilted Left/Area Scan (7x14x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.009 mW/g Tilted Left/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.62 V/m; Power Drift = -0.020 dB Peak SAR (extrapolated) = 0.013 W/kg SAR(1 g) = 0.00846 mW/g; SAR(10 g) = 0.0051 mW/g Fig. 2: SAR distribution for DECT US, channel 2, tilted position, left side of head (December 8, 2015) SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Plots Page 4 of 5 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR Test Laboratory: IMST GmbH, DASY Yellow (II); File Name: TGCA35_yprm_1.da4 DUT: Panasonic; Type: KX-TGCA35; Serial: SA35BS1128 Program Name: Cheek Right Communication System: DECT Handset; Frequency: 1924.99 MHz;Duty Cycle: 1:24 Medium parameters used: f = 1925 MHz; σ = 1.41 mho/m; ε r = 40.8; ρ = 1000 kg/m 3 Phantom section: Right Section DASY4 Configuration: - Probe: ET3DV6R - SN1669; ConvF(4.97, 4.97, 4.97); Calibrated: 2/19/2015 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 2/19/2015 - Phantom: SAM 1340; Type: QD 000 P40 CB; Serial: TP-1340 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Cheek Right/Area Scan (7x14x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.014 mW/g Cheek Right/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 3.01 V/m; Power Drift = -0.113 dB Peak SAR (extrapolated) = 0.020 W/kg SAR(1 g) = 0.013 mW/g; SAR(10 g) = 0.00792 mW/g Fig. 3: SAR distribution for DECT US, channel 2, cheek position, right side of head (December 8, 2015) SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Plots Page 5 of 5 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR Test Laboratory: IMST GmbH, DASY Yellow (II); File Name: TGCA35_yprm_2.da4 DUT: Panasonic; Type: KX-TGCA35; Serial: SA35BS1128 Program Name: DECT Communication System: DECT Handset; Frequency: 1924.99 MHz;Duty Cycle: 1:24 Medium parameters used: f = 1925 MHz; σ = 1.41 mho/m; ε r = 40.8; ρ = 1000 kg/m 3 Phantom section: Right Section DASY4 Configuration: - Probe: ET3DV6R - SN1669; ConvF(4.97, 4.97, 4.97); Calibrated: 2/19/2015 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 2/19/2015 - Phantom: SAM 1340; Type: QD 000 P40 CB; Serial: TP-1340 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Tilt Right/Area Scan (7x14x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.010 mW/g Tilt Right/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.79 V/m; Power Drift = -0.054 dB Peak SAR (extrapolated) = 0.014 W/kg SAR(1 g) = 0.00905 mW/g; SAR(10 g) = 0.00545 mW/g Fig. 4: SAR distribution for DECT US, channel 2, tilted position, right side of head (December 8, 2015)

Report No. 299189-2 Template version: C Nemko Norway Nemko AS, Instituttveien 6, P.O. Box 96 Kjeller, 2007 Kjeller, Norway TEL +47 22 96 03 30 FAX +47 22 96 05 50 EMAIL [email protected] ENTERPRISE NUMBER NO974404532 nemko.com/no Test Report Product UPCS handset Name and address of the applicant Panasonic Corporation of North America Name and address of the manufacturer Panasonic System Networks Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku Fukuoka 812-8531, Japan Model KX-TGCA35 KX-TGCA38C Rating 2.5V DC (Secondary Batteries) Trademark Panasonic Serial number / Additional information DECT 6.0 Tested according to FCC Part 15, subpart D Isochronous UPCS Device, 1920 – 1930 MHz Industry Canada RSS 213, Issue 3 2 GHz License-Exempt Personal Communications Services (LE-PCS) Devices Order number 299189 Tested in period 2015.10.30 to 2015.11.26 Issue date 2015.12.03 Name and address of the testing laboratory Instituttveien 6 Kjeller, Norway FCC No: 994405 IC OATS: 2040D-1 TEL: +47 22 96 03 30 FAX: +47 22 96 05 50 Prepared by [Frode Sveinsen] Approved by [G.Suhanthakumar] This report shall not be reproduced except in full without the written approval of Nemko. Opinions and interpretations expressed within this report are not part of the current accreditation. This report was originally distributed electronically with digital signatures. For more information please contact Nemko. TEST REPORT FCC part 15D Report no.: 299189-2 FCC ID: ACJ96NKX-TGCA35 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 2 (48) CONTENTS 1 INFORMATION ................................................................................................................................. 3 1.1 Tested Item........................................................................................................................................ 3 1.2 Description of Tested Device ............................................................................................................. 3 1.3 Exposure Evaluation .......................................................................................................................... 3 1.4 Test Environment .............................................................................................................................. 4 1.5 Test Engineer(s) ................................................................................................................................ 4 1.6 Test Equipment ................................................................................................................................. 4 1.7 Other Comments ............................................................................................................................... 4 2 TEST REPORT SUMMARY .............................................................................................................. 5 2.1 General .............................................................................................................................................. 5 2.2 Test Summary ................................................................................................................................... 6 3 TEST RESULTS ................................................................................................................................ 7 3.1 Power Line Conducted Emissions ..................................................................................................... 7 3.2 Digital Modulation Techniques ........................................................................................................ 10 3.3 Labeling Requirements ................................................................................................................... 10 3.4 Channel Frequencies ...................................................................................................................... 10 3.5 Antenna Requirement...................................................................................................................... 11 3.6 Automatic Discontinuation of Transmission .................................................................................... 11 3.7 Peak Power Output ......................................................................................................................... 12 3.8 Emission Bandwidth B ..................................................................................................................... 15 3.9 Power Spectral Density ................................................................................................................... 18 3.10 In-Band Unwanted Emissions, Conducted ...................................................................................... 21 3.11 Out-of-band Emissions, Conducted................................................................................................. 23 3.12 Carrier Frequency Stability .............................................................................................................. 29 3.13 Frame Repetition Stability ............................................................................................................... 30 3.14 Frame Period and Jitter ................................................................................................................... 30 3.15 Monitoring Threshold, Least Interfered Channel ............................................................................. 32 3.16 Threshold Monitoring Bandwidth ..................................................................................................... 34 3.17 Reaction Time and Monitoring Interval ............................................................................................ 35 3.18 Time and Spectrum Window Access Procedure ............................................................................. 37 3.19 Acknowledgements and Transmission Duration ............................................................................. 38 3.20 Dual A…

Text truncated - open the document above for the full version.

TEST SET-UP PHOTOS Project no.: 297372 FCC ID: ACJ96NKX-TGCA35 Page 1 (1) PHOTOS OF TEST SET-UP – KX-TGCA35 Power line Conducted Emissions Test

SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Pics Page 1 of 4 The Testcenter facility ‘Dosimetric Test Lab’ within IMST GmbH is accredited by the German National ‘Deutsche Akkreditierungsstelle GmbH (DAkkS)’ for testing according to the scope as listed in the accreditation certificate: D-PL-12139-01-00. Appendix for the SAR Test Report Dosimetric Assessment of the Portable Device KX-TGCA35 from Panasonic (FCC ID: ACJ96NKX-TGCA35) According to the FCC Requirements Pictures December 9, 2015 IMST GmbH Carl-Friedrich-Gauß-Str. 2 - 4 47475 Kamp-Lintfort Germany Customer Panasonic System Networks Co., Ltd. 1 - 62, 4 - chome Minoshima, Hakata-ku, Fukuoka 812-8531 Japan The test results only relate to the items tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Pics Page 2 of 4 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR Subject of Investigation Fig. 1: Pictures of the device under test. SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Pics Page 3 of 4 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR 7.9 Pictures of the Device under Test Figure 11 - 12 show the device under test and the used accessory. Fig. 11: Pictures of the front side of device under test. Fig. 12: Pictures of the back side of device under test. SAR_Report_Nemko_60320_6150683_FCC_DECT_KX-TGCA35_Pics Page 4 of 4 SAR_Report_FCC_DECT_WiFI_Head_Body_1.0/10.12.2013/AR 7.10 Test Positions for the Device under Test Figure 13 - 16 show the test positions for the SAR measurements. Fig. 13: Cheek position, left side. Fig. 14: Tilted position, left side. Fig. 15: Cheek position, right side. Fig. 16: Tilted position, right side.