ACJ96NKX-TGEA60ADECT Handset

Installation Manual Additional Digital Cordless Handset Model No. KX-TGEA60 KX-TGEA61 Thank you for purchasing a Panasonic product. This unit is an additional handset compatible with the following series of Panasonic Digital Cordless Phone: – KX-TGE630/KX-TGE640 (KX-TGEA60/KX-TGEA61) – KX-TGE660/KX-TGE670 (KX-TGEA61) (The corresponding models are subject to change without notice.) You must register this handset with your base unit before it can be used. This installation manual describes only the steps needed to register and begin using the handset. Please read the base unit’s operating instructions for further details. Please read this installation manual before using the unit and save it for future reference. For assistance, visit our Web site: http://shop.panasonic.com/support for customers in the U.S.A. Printed in Malaysia PNQX8640XA PP1117HD2051 KX-TGEA60_(en-US)_0728_ver201.pdf 18/19/2021 9:43:37 AM Accessory information Supplied accessories Accessory item/Part numberQuantity Charger/PNLC1079ZB1 Rechargeable batteries/HHR-4DPA2 Handset cover/PNYNTGEA60BR * 1 1 Belt clip/PNKE2125Z11 *1 The handset cover comes attached to the handset. N ote: RPlease read the base unit’s operating instructions for additional/replacement accessories. – Optional headsets: KX-TCA93, KX-TCA430 RPlease read “Graphical symbols for use on equipment and their descriptions” of the base unit’s operating instructions. For your safety T o prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection RCompletely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. RRegularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire. RUnplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact us at http://shop.panasonic.com/support 2 For a ssistance, please visit http://shop.panasonic.com/support Installation KX-TGEA60_(en-US)_0728_ver201.pdf 28/19/2021 9:43:38 AM Installation RTo prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. RDo not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. CAUTION Installation and location RT he AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. Battery RW e recommend using the supplied batteries or additional/replacement batteries noted on page 2 for replacement battery information. USE ONLY rechargeable Ni-MH batteries AAA (R03) size. RDo not mix old and new batteries. RDo not open or mutilate the batteries. Released electrolyte from the batteries is corrosive and may cause burns or injury to the eyes or skin. The electrolyte is toxic and may be harmful if swallowed. RExercise care when handling the batteries. Do not allow conductive materials such as rings, bracelets, or keys to touch the batteries, otherwise a short circuit may cause the batteries and/or the conductive material to overheat and cause burns. RCharge the batteries provided with or identified for use with this product only, in accordance with the instructions and limitations specified in this manual. ROnly use a compatible base unit (or charger) to charge the batteries. Do not tamper with the base unit (or charger). Failure to follow these instructions may cause the batteries to swell or explode. Attention: A nickel metal hydride battery that is r ecyclable powers the product you have purchased. Please call 1-800-8-BATTERY (1-800-822-8837) for information on how to recycle this battery. For a ssistance, please visit http://shop.panasonic.com/support 3 Installation KX-TGEA60_(en-US)_0728_ver201.pdf 38/19/2021 9:43:38 AM Important safety instructions When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool. 2. Do not use the telephone to report a gas leak in the vicinity of the leak. 3. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. SAVE THESE INSTRUCTIONS Other information RO perating the product near electrical appliances may cause interference. Move away from the electrical appliances. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Routine care RW ipe the outer surface of the product with a soft moist cloth. RDo not use benzine, thinner, or any abrasive powder. Notice for product disposal, transfer, or return RT his product can store your private/confidential information. To protect your privacy/confidentiality, we recommend that you erase information such as phonebook or caller list entries from the memory before you dispose of, transfer, or return the product. Setting up Connections/Wall mounting Connect the AC adaptor to the power outlet. Drive the screws ( 1 ) (not supplied) into the wall, if necessary. 4 For a ssistance, please visit http://shop.panasonic.com/support Installation KX-TGEA60_(en-US)_0728_ver201.pdf 48/19/2021 9:43:38 AM 2 27.2 mm (1 1 /16 inches) 1 1 2 2 Note: RT he AC adaptor must remain connected at all times. (It is normal for the adaptor t…

Text truncated - open the document above for the full version.

Covered Equipment CFR 47 §2.911 (d)(5) Attestation March 6, 2023 PASA-22-F002 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: FCC ID: ACJ96NKX-TGEA60A To whom it may concern: Panasonic Corporation of North America certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Panasonic Corporation of North America certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Ben Botros Manager – Regulatory & Compliance Panasonic Corporation of North America

Panasonic Corporation of North America Two Riverfront Plaza, Newark, NJ 07102-5490 Tel: 201-348-7760 / [email protected] Ben Botros Manager – Regulatory Compliance Panasonic Corporation of North America Agent Designation Attestation CFR 47 §2.911 (d)(7) Federal Communications Commission Date: March 9, 2023 Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: FRN 0003762242 with FCC Grantee Code ACJ - Attestation Statements Part 2.911(d)(7) Panasonic Corporation of North America (“the applicant”) certifies that, Panasonic Corporation of North America is our designated U.S. agent for service of process for the above referenced FCC Grantee Code ACJ. Panasonic Corporation of North America accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Panasonic Corporation of North America accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for Grantee Code ACJ. Designated U.S. Agent Information: Name: Panasonic Corporation of North America Address: Two Riverfront Plaza, Newark, New Jersey, United States Contact Person: Ben Botros Tel.: 201-348-7760 Email: [email protected] This agreement applies to all products applied by Panasonic Corporation of North America for FCC Grantee Code ACJ and is valid within the product life. Sincerely, Ben Botros Manager – Regulatory & Compliance Panasonic Corporation of North America

Panasonic Corporation of North America Two Riverfront Plaza, Newark, NJ 07102-5490 Tel/Fax: 201-348-7760 / [email protected] Ben Botros, Manager – Regulatory & Compliance Panasonic Corporation of North America Agent Authorization Letter March 22, 2023 PCTP-22-F002 Nemko Scandinavia AS Instituttveien 6, Kjeller, Norway 2007 Re: Original Application for Panasonic Models: KX-TGEA60A under FCC ID ACJ96NKX-TGEA60A for FCC Parts 15B and 15D To whom it may concern: The undersigned hereby authorize Mr. Frode Sveinsen of Nemko Scandinavia AS, Norway to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Nemko Scandinavia AS on our behalf shall have the same effect as acts of our own including completion of form 731. The undersigned hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing Nemko Scandinavia AS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; Panasonic Corporation of North America Two Riverfront Plaza, Newark, NJ 07102-5490 Tel/Fax: 201-348-7760 / [email protected] Ben Botros, Manager – Regulatory & Compliance Panasonic Corporation of North America h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is for Single Certification for the above models under FCC ID: ACJ96NKX-TGEA60A and is valid for one-year period from the date of this letter. Thank you for your attention in this matter. Sincerely, Ben Botros Manager – Regulatory and Compliance Panasonic Corporation of North America

Panasonic Corporation of North America Two Riverfront Plaza, Newark, NJ 07102-5490 Tel/Fax: 201-348-7760 / [email protected] Ben Botros, Manager – Regulatory & Compliance Panasonic Corporation of North America Request for Permanent & Short-Term Confidentiality March 22, 2023 PCTP-22-F002 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada, K1V 1H2 Re: Original Application for Panasonic Models: KX-TGEA60A under FCC ID ACJ96NKX-TGEA60A for FCC Parts 15B and 15D To whom it may concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §0.457, §0.459), we are requesting the Commission to withhold the following attachments as permanent confidentiality documents from public disclosure: • Schematics • Bill of Materials/Parts List • Block Diagrams • Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In addition, pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules and the provisions in FCC Public DA 04-1705, please be advised that Panasonic Corporation of North America hereby requests the following filed sensitive information to be held under 45-day short-term confidentiality starting from the original issued Certification grant date:  Internal Photos  External Photos  User Manual  Test Set-up Photographs When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. Thank you for your attention in this matter. Sincerely, Ben Botros Manager – Regulatory and Compliance Panasonic Corporation of North America

EXTERNAL PHOTOGRAPHS KX-TGEA60 Top View Bottom View

EXHIBIT B MARKINGS Portable Unit: FCC ID Label (Nameplate) The marking will be shown on the battery compartment of the portable unit.

INTERNAL PHOTOGRAPHS KX-TGEA60 Internal View Internal View 2 Internal View 2

SAR_FCC_ISED_6230031_Appendix Page 22 of 53 Appendixes for Report SAR_FCC_ISED_6230031 DUT Information Manufacturer Panasonic Entertainment & Communication Co., Ltd. Brand Name KX-TGEA60 Model Under Test KX-TGEA60 FCC ID ACJ96NKX-TGEA60A Type / Category handset Intended Use < 20 cm to human body (portable device) > 20 cm to human body (mobile/fixed device) - next to the ear body-worn limb-worn hand-held front-of-f ac e body supported clothing-integrated Prepared by Testing Laboratory IMST GmbH, Test Center Carl-Friedrich-Gauß-Str. 2 – 4 47475 Kamp-Lintfort Germany Prepared for Applicant / Manufacturer Applicant Manufacturer Panasonic Corporation of North America Panasonic Corporation Two Riverfront Plaza, 9th Floor 1006, Oaza Kadoma, Kadoma-shi Newark, 07102-5490, NJ Osaka 571-8501 USA Japan Test Specification Applied Standard / Rule FCC CFR 47 § 2.1093; IEC/IEEE 62209-1528; Exposure Category general public / uncontrolled exposure occupational / controlled exposure Test Result PASS FAIL Report Information Data Stored 6230031 Issue Date January 16, 2023 Revision Date Revision Number* *A new revision replaces all previous revisions and thus, become invalid herewith. Appendixes Appendix A - Pictures Appendix B - SAR Distribution Plots Appendix C - System Verification Plots Appendix D – Certificates of Conformity Appendix E – Calibration Certificates for DAEs Appendix F – Calibration Certificates for E-Field Probes Appendix G – Calibration Certificates for Dipoles Appendix Issue Date: January 16, 2023 Revision Date: Revision No.: SAR_FCC_ISED_6230031_Appendix Page 27 of 53 Appendix B - SAR Distribution Plots Worst Case SAR Measurement Plots for Head and Body Worn Configuration Test Laboratory: IMST GmbH, DASY Yellow (II); File Name: KX-TGEA60_2Dy_DECT_CH2_lm_1.da4 DUT: Panasonic; Type: KX-TGEA60; Serial: 01 Program Name: DECT US Communication System: DECT US; Frequency: 1924.99 MHz;Duty Cycle: 1:24 Medium parameters used: f = 1925 MHz; σ = 1.42 mho/m; ε r = 41.4; ρ = 1000 kg/m 3 Phantom section: Left Section DASY4 Configuration: - Probe: ET3DV6R - SN1579; ConvF(5.46, 5.46, 5.46); Calibrated: 2/25/2022 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 2/17/2022 - Phantom: SAM 1340; Type: QD 000 P40 CB; Serial: TP-1340 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Cheek Left/Area Scan (7x13x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.034 mW/g Cheek Left/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 3.22 V/m; Power Drift = 0.127 dB Peak SAR (extrapolated) = 0.053 W/kg SAR(1 g) = 0.029 mW/g; SAR(10 g) = 0.016 mW/g Maximum value of SAR (measured) = 0.033 mW/g Minimum distance from peak to all points 3 dB below in M1 = 14.0 mm Ratio of SAR at M2 to SAR at M1 = 55.60 % Plot. 1: SAR distribution plot for DECT, channel 2, head configuration, left cheek. Appendix Issue Date: January 16, 2023 Revision Date: Revision No.: SAR_FCC_ISED_6230031_Appendix Page 28 of 53 Test Laboratory: IMST GmbH, DASY Yellow (II); File Name: KX-TGEA60_2Dy_DECT_CH2_front.da4 DUT: Panasonic; Type: KX-TGEA60; Serial: 01 Program Name: DECT US Communication System: DECT US; Frequency: 1924.99 MHz;Duty Cycle: 1:24 Medium parameters used: f = 1925 MHz; σ = 1.42 mho/m; ε r = 41.4; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY4 Configuration: - Probe: ET3DV6R - SN1579; ConvF(5.46, 5.46, 5.46); Calibrated: 2/25/2022 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 2/17/2022 - Phantom: SAM 1340; Type: QD 000 P40 CB; Serial: TP-1340 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Body Worn/Area Scan (7x14x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.023 mW/g Body Worn/Zoom Scan (6x6x7)/Cube 0: Measurement grid: dx=6mm, dy=6mm, dz=5mm Reference Value = 3.10 V/m; Power Drift = 0.147 dB Peak SAR (extrapolated) = 0.043 W/kg SAR(1 g) = 0.023 mW/g; SAR(10 g) = 0.012 mW/g Maximum value of SAR (measured) = 0.026 mW/g Minimum distance from peak to all points 3 dB below in M1 = 12.0 mm Ratio of SAR at M2 to SAR at M1 = 53.69 % Plot. 2: SAR distribution plot for DECT, channel 2, body-w orn configuration, front side, 0mm gap. Appendix Issue Date: January 16, 2023 Revision Date: Revision No.: SAR_FCC_ISED_6230031_Appendix Page 29 of 53 Appendix C - System Verification Plots Test Laboratory: IMST GmbH, DASY Yellow (II); File Name: 2022-12-19_1900h_2Dy_1579_335.da4 DUT: D1900V2 - SN535; Type: D1900V2; Serial: SN535 Program Name: System Performance Check at 1900 MHz Communication System: CW; Frequency: 1900 MHz;Duty Cycle: 1:1 Medium parameters used: f = 1900 MHz; σ = 1.4 mho/m; ε r = 41.6; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY4 Configuration: - Probe: ET3DV6R - SN1579; ConvF(5.46, 5.46, 5.46); Calibrated: 2/25/2022 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 2/17/2022 - Phantom: SAM 1340; Type: QD 000 P40 CB; Serial: TP-1340 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 d=10mm, Pin=250mW/Area Scan (5x8x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 9.90 mW/g d=10mm, Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 101.8 V/m; Power Drift = 0.008 dB Peak SAR (extrapolated) = 15.9 W/kg SAR(1 g) = 9.48 mW/g; SAR(10 g) = 5.03 mW/g Maximum value of SAR (measured) = 10.7 mW/g Plot. 3: SAR Verification Measurement 1900 MHz. Appendix Issue Date: January 16, 2023 Revision Date: Revision No.: SAR_FCC_ISED_6230031_Appendix Page 30 of 53 Appendix D – Certificates of Conformity Fig. 4: Certificate of conformity for the used DASY4 system: Appendix Issue Date: January 16, 2023 Revision Date: Revision No.: SAR_FCC_ISED_6230031_Appendix Page 31 of 53 Fig. 5: Certificate of conformity for the used SAM phantom. Appendix Issue Date: January 16, 2…

Text truncated - open the document above for the full version.

REP003693 Template version: D Nemko Group Nemko Scandinavia AS, Instituttveien 6, 2007 Kjeller, Norway TEL +47 22 96 03 30 EMAIL [email protected] nemko.com/no Test Report Product DECT Handset Name and address of the applicant Panasonic Corporation of North America Two Riverfront Plaza, 9 th Floor Newark, 07102-5490, NJ, USA Name and address of the manufacturer Panasonic Entertainment & Communication Co., Ltd. 1-10-12 Yagumo-higashi-machi, Moriguchi City, Osaka 570-0021, Japan Model KX-TGEA60 Rating 2.4V DC (2x AAA NiMH cells) Trademark Panasonic Additional information DECT 6.0 Tested according to FCC Part 15, subpart D Isochronous UPCS Device, 1920 – 1930 MHz Industry Canada RSS 213, Issue 3 2 GHz License-Exempt Personal Communications Services (LE-PCS) Devices Order number PRJ0025968 Tested in period 2023-01-03 to 2023-01-04 Issue date 2023-02-10 Name and address of the testing laboratory Instituttveien 6 Kjeller, Norway www.nemko.com CAB Number: FCC: NO0001 ISED: NO0470 An accredited technical test executed under the Norwegian accreditation scheme Prepared by [Frode Sveinsen] Approved by [G. Suhanthakumar] This report shall not be reproduced except in full without the written approval of Nemko. Opinions and interpretations expressed within this report are not part of the current accreditation. This report was originally distributed electronically with digital signatures. For more information please contact Nemko. TEST REPORT FCC part 15D REP003693 FCC ID: ACJ96NKX-TGEA60A Nemko Scandinavia AS Page 2 (40) Revision history Revision Date Comment Sign A 2023-02-10 First Edition FS THIS TEST REPORT APPLIES ONLY TO THE ITEM(S) AND CONFIGURATIONS TESTED. Deviations from, additions to, or exclusions from the test specifications are described in “Summary of Test Data”. Nemko Group authorizes the above named entity to reproduce this report provided it is reproduced in its entirety and for use by the entity’s employees only. Any reproduction of parts of this report requires approval in writing from Nemko Group. Any use that a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Group accepts no responsibility for damages suffered by any third party caused by decisions made or actions based on this report. TEST REPORT FCC part 15D REP003693 FCC ID: ACJ96NKX-TGEA60A Nemko Scandinavia AS Page 3 (40) CONTENTS 1 INFORMATION ................................................................................................................................. 4 1.1 Tested Item ........................................................................................................................................................ 4 1.2 Description of Tested Device .............................................................................................................................. 4 1.3 Test Conditions .................................................................................................................................................. 4 1.4 Test Engineer(s) ................................................................................................................................................. 4 1.5 Digital Modulation Techniques ............................................................................................................................ 4 1.6 Antenna Requirement ......................................................................................................................................... 5 1.7 Channel Frequencies ......................................................................................................................................... 5 1.8 Other Comments ................................................................................................................................................ 5 2 TEST REPORT SUMMARY .............................................................................................................. 6 2.1 General .............................................................................................................................................................. 6 2.2 Test Summary .................................................................................................................................................... 6 3 TEST RESULTS ................................................................................................................................ 8 3.1 Power Line Conducted Emissions ...................................................................................................................... 8 3.2 Automatic Discontinuation of Transmission....................................................................................................... 10 3.3 Peak Power Output .......................................................................................................................................... 11 3.4 Emission Bandwidth B ...................................................................................................................................... 13 3.5 Power Spectral Density .................................................................................................................................... 15 3.6 In-Band Unwanted Emissions, Conducted ........................................................................................................ 17 3.7 Out-of-band Emissions, Conducted .................................................................................................................. 19 3.8 Carrier Frequency Stability ............................................................................................................................... 23 3.9 Frame Repetition Stability ................................................................................................................................. 24 3.10 Frame Period and Jitter ......................…

Text truncated - open the document above for the full version.

FCC Part 15D – Compliance Information Nemko AS, Instituttveien 6, 2007 Kjeller, Norway kx-tgea60_fcc part 15d declarations signed Tel: +47 22 96 03 30 Fax: +47 22 96 05 50 Page 1 (4) rev.3.0 24-June-2019 Email: [email protected] EUT AND PRODUCT INFORMATION Type of Equipment UPCS (DECT 6.0) Applicant Name Panasonic Corporation of North America Address Two Riverfront Plaza, 9th floor Newark, NJ 07102-5490, USA. Contact Ben Botros Phone 201-348-7760 Email [email protected] Brand Name Panasonic BASE STATION HANDSET / PORTABLE Wireless Relay Station / Repeater EUT Type/System ☐ ☒ ☐ Modular Approval ☐ YES ☐ LMA ☐ YES ☐ LMA ☐ YES ☐ LMA FCC ID ACJ96NKX-TGEA60A ISED ID (Canada) - Model name KX-TGEA60 HVIN - PMN - HW Version S1 SW Version SW201 Maximum Antenna Gain 0dBi Is EUT Initiating Device ☐ YES ☒ YES ☐ YES Does EUT transmit signaling channels ☐ YES ☐ YES ☐ YES Number of slots in use simultaneously 1 slot Frequency Band 1921.536 – 1928.448 MHz Number of RF Channels 5 Frame Period 10 ms Max. Burst length 417us / duplex channel Min. Burst Length 106us / signaling channel Number of System Channels 60 (12 duplex channels per RF carrier) Supported DECT Slot Types ☒ Full Slot ☐ Long Slot ☐ Double Slot Operating Mode ☐ Simplex ☒ Duplex ANTENNA DIVERSITY Antenna Diversity Supported TX RX Base Station 1 ☐ ☐ 2 ☐ ☐ 3 ☐ ☐ 4 ☐ ☐ Handset 1 ☐ ☐ 2 ☐ ☐ FCC Part 15D – Compliance Information Nemko AS, Instituttveien 6, 2007 Kjeller, Norway kx-tgea60_fcc part 15d declarations signed Tel: +47 22 96 03 30 Fax: +47 22 96 05 50 Page 2 (4) rev.3.0 24-June-2019 Email: [email protected] ANTENNAS Base Station Antenna Type Internal External 1 ☐ ☐ 2 ☐ ☐ 3 ☐ ☐ 4 ☐ ☐ Does RX and TX use the same antenna(s)? ☐ Yes ☐ No Handset Antenna Type Internal External 1 Pattern Antenna ☒ ☐ 2 ☐ ☐ 3 ☐ ☐ Does RX and TX use the same antenna(s)? ☒ Yes ☐ No VOLTAGE AND TEMPERATURE RANGES VOLTAGES Base Station Handset or Portable WRS Nominal Voltage - DC 2.4V - Cut-Off Voltage (if applicable) - - - POWER SOURCE Type Manufacturer Base Station or WRS - - Handset (Charger) PNLV233 (Charger) Panasonic Connections on Base ☒ PSTN ☐ USB ☐ Ethernet ☐ Others (please specify) .... ANCILLARY EQUIPMENT Description Charger Type PNLV233 (Charger) Manufacturer Panasonic HOST DEVICE Description Type Manufacturer ADDITIONAL INFORMATION FCC Part 15D – Compliance Information Nemko AS, Instituttveien 6, 2007 Kjeller, Norway kx-tgea60_fcc part 15d declarations signed Tel: +47 22 96 03 30 Fax: +47 22 96 05 50 Page 3 (4) rev.3.0 24-June-2019 Email: [email protected] MANUFACTURERS DECLARATIONS FCC part 15.323 (c)(5) The applicant declares that the system in this application has more than 20 duplex system access channels defined, and that the system is operating in Least Interfered Channel (LIC) mode in accordance with this section. Applicant Agrees ☒ Yes ☐ No FCC part 15.323 (c)(5) No device or group of co-operating devices located within 1m of each other shall during any frame period occupy more than 6 MHz of aggregate bandwidth, or alternatively, more than one third of the time and spectrum windows defined by the system. Applicant Agrees ☒ Yes ☐ No FCC part 15.323 (c)(10) The applicant hereby declares that the system in this application does use the criteria of (c)(10) of this section. Applicant Agrees ☒ Yes ☐ No FCC part 15.323 (c)(11) The applicant hereby declares that system in this application does not use the criteria of (c)(11) of this section. Applicant Agrees ☒ Yes ☐ No FCC part 15.323 (c)(12) The provisions of (c)(10) or (c)(11) of this section shall not be used to extend the range of spectrum occupied over space or time for the purpose of denying fair access to spectrum to other devices. Applicant Agrees ☒ Yes ☐ No ADDITIONAL REMARKS: > DECLARED BY: > Date March 7, 2023 > Name (print)Ben Botros Signature FCC Part 15D – Compliance Information Nemko AS, Instituttveien 6, 2007 Kjeller, Norway kx-tgea60_fcc part 15d declarations signed Tel: +47 …

Text truncated - open the document above for the full version.