ACJ96NKX-TGWA40DECT Cordless Base Station - Deskset

Installation Manual 4-Line Phone Home Office | Small Business Additional Desk Phone Model No. KX-TGWA40 Thank you for purchasing a Panasonic product. This unit is an additional desk phone compatible with KX-TGW420. (The corresponding models are subject to change without notice.) You must register this desk phone with your base unit (KX-TGW420) before it can be used. This installation manual describes only the steps needed to register and begin using the desk phone. Please read the base unit’s operating instructions for further details. Please read this installation manual before using the unit and save it for future reference. For assistance, visit our Web site: http://shop.panasonic.com/support for customers in the U.S.A. Printed in Malaysia PNQX8979ZA PP1119MU0 TGWA40_(en)_OI_1213_ver005.pdf 12019/12/13 11:11:06 Accessory information Supplied accessories No.Accessory item/Part numberQuantity AAC adaptor/PNLV254-0Z1 BDesk stand/PNKL1080Z11 CCorded handset/PNLXU1017Z1 DCorded handset cord/PQJA212V1 ABCD Note: RP lease read the base unit’s operating instructions for additional/replacement accessories. RPlease read “Graphical symbols for use on equipment and their descriptions” of the base unit’s operating instructions. 2 For assistance, please visit http://shop.panasonic.com/support Introduction TGWA40_(en)_OI_1213_ver005.pdf 22019/12/13 11:11:07 For your safety T o prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection RU se only the power source marked on the product. RDo not overload power outlets and extension cords. This can result in the risk of fire or electric shock. RCompletely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. RRegularly remove any dust, etc. from the AC adaptor/ power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire. RUnplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact us at http://shop.panasonic.com/support RUnplug from power outlets and never touch the inside of the product if its casing has been broken open. RNever touch the plug with wet hands. Danger of electric shock exists. Installation RT o prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. RDo not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. CAUTION Installation and location RT he AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. Note when using Alkaline batteries for power back-up RT he batteries should be used correctly, otherwise the unit may be damaged due to battery leakage. RDo not charge, short-circuit, disassemble, or heat the batteries. RDo not dispose of batteries in a fire. RRemove all the batteries when replacing. RDo not mix old, new or different types of batteries. RIt is recommended that batteries are replaced annually. RIt is recommended that batteries are replaced after a power outage. Important safety instructions W hen using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool. 2. Do not use the telephone to report a gas leak in the vicinity of the leak. 3. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. SAVE THESE INSTRUCTIONS Other information RO perating the product near electrical appliances may cause interference. Move away from the electrical appliances. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Routine care RWipe the outer surface of the product with a soft moist cloth. RDo not use benzine, thinner, or any abrasive powder. Notice for product disposal, transfer, or return RT his product can store your private/confidential information. To protect your privacy/confidentiality, we recommend that you erase information such as phonebook or caller list entries from the memory before you dispose of, transfer, or return the product. Notice For assistance, please visit http://shop.panasonic.com/support 3 Important Information TGWA40_(en)_OI_1213_ver005.pdf 32019/12/13 11:11:07 Specifications RF requency range: 1.92 GHz to 1.93 GHz RRF transmission power: 112 mW (max.) RPower source: 120 V AC, 60 Hz RPower consumption: Standby: 1.0 W Maximum: 3.0 W ROperating conditions: 0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 % relative air humidity (dry) 4 For assistance, please visit http://shop.panasonic.com/support Important Information TGWA40_(en)_OI_1213_ver005.pdf 42019/12/13 11:11:07 Setting up Connection Connect the AC adaptor to the unit by p ressing the plug firmly. Connect the AC adaptor to the power outlet. Fasten the AC adaptor cord by hooking it. Connect the corded handset cord to the c orded handset and the desk phone until you hear a click. Note: RUse only the supplied AC adaptor KSAS0050750080VUD. 1 2 4 4 3 1 Note when setting up Note for connections RThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) RThe AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not …

Text truncated - open the document above for the full version.

Two Riverfront Plaza | Newark, NJ 07102-5490 Ben Botros, Project Manager Safety , Compliance and Quality Assurance Authorization Letter December 12, 2019 PCTP-19-F009 Federal Communication Commission Equipment Authorization Division / Application Processing Branch 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern; Panasonic Corporation of North America hereby authorizes Intertek Testing Services (Mr. Terry Chan / Tim Lee/ Herbert Wong / Kenneth Wong) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and Part 18 of the FCC Rules for the product specified below only. I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.,862. FCC ID: ACJ96NKX-TGWA40 Type Filing: Original Application for UPCS Cordless Telephone Model Numbers: KX -TGWA40 FCC Classification: Isochronous UPCS Base Station (PUB) FCC Rule Part: FCC Part 15, Subpart D Frequency Range: 1921.536 ~ 1928.448 Number Channels: 5 RF Channels / 5x12 = 60 TDMA Duplex Channels RF Exposure: Portable / SAR (zero spacing between antenna and head/body is acceptable) FCC Rule Part: FCC Part 15, Subpart B FCC Classification: Class B Digital Device (JAB) Sincerely yours, Ben Botros Project Manager Panasonic Corporation of North America Safety, Compliance and Quality Assurance

Two Riverfront Plaza | Newark, NJ 07102-5490 Ben Botros, Project Manager Safety , Compliance and Quality Assurance Request for Confidential ity December 12, 2019 PCTP-19-F009 Federal Communication Commission Equipment Authorization Division / Application Processing Branch 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern; FCC ID: ACJ96NKX-TGWA40 Type Filing: Original Application for UPCS Cordless Telephone Model Numbers: KX-TGWA40 Request For Permanent Confidentiality In accordance with provisions of Sections §§0.457(d) and 0.459 of the Commission’s Rules and Section 552(b)(4) of the Freedom of Information Act, we request permanent confidentiality for exhibits, which contain: (1) Description of Electrical Circuitry; (2) Schematic Diagrams of Base Unit and RF Unit; and (3 ) Base Unit Block Diagram. Rationale: The transmitter is not user adjustable and does not have a Tune-Up Procedure. These exhibits contain proprietary, confidential and trade secrets material, which would not be routinely made available for public inspection and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development Request For Short-Term Confidentiality In accordance with FCC Public DA 04-1705, we request 180 day short-term confidentiality, starting from the from the issuance of equipment authorization date, for exhibits, which contain: (1) External Photographs of Base Unit and RF Unit; (2) Internal Photographs of Base Uni t and RF Unit; (3) Test Setup Photographs; and (4) User Manual. Rationale: These exhibits contain pre-market information, which could give our competitors unfair advantage should this information be released before this product is actually introduced into the common marketplace. Sincerely yours, Ben Botros Project Manager Panasonic Corporation of North America Safety, Compliance and Quality Assurance

15 January 2020 To whom it may concern, Declarations FCC ID: ACJ96NKX-TGWA40 I, the undersigned, hereby declare that 1. The device does not use the provisions of 47CFR 15.323 (c) (6), random waiting mechanism is not used in this system. 2. The provisions of 47CFR 15.323 (c) (10) and 47CFR 15.323 (c) (11) are not used to extend the range of spectrum occupied over space or time for the purpose of denying fair access to spectrum to other devices. 3. Only the Deskset will act as the initiating device, which will initiate the establishment of the duplex connection. 4. The device complies with the provisions of 47CFR 15.319(f). The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude transmission of control and signaling information or use of repetitive codes used by certain digital technologies to complete frame or burst intervals. The following table explains the reaction of device in case of either absence of information to transmit or operational failure after a connection of its companion device is established. Circumstances Reaction of Deskset 1 Switch-off companion device NA 2 On hook by companion device C 3 Switch-off device NA 4 On hook on device side C 5 Remove power from device C 6 Remove power from companion device A A – Connection is terminated and, transmission ceases. B – Connection is terminated but device transmits control or signaling information. C – Connection is terminated but companion device transmits control or signaling information. NA – Not applicable represents the device does not contain a hook switch or a power off switch. 5. M L of Deskset declared by manufacturer are 30dBm. If you have questions or need further information, please contact the undersigned. Regards,

INTERTEK TESTING SERVICES External Photos FCC ID: ACJ96NKX-TGWA40 INTERTEK TESTING SERVICES External Photos FCC ID: ACJ96NKX-TGWA40

45.0 (2:1) 21.0 (2:1) KX-TGWA40B PNGTA854ZA/M1 2019.**.** 2:1

INTERTEK TESTING SERVICES Internal photos FCC ID: ACJ96NKX-TGWA40 INTERTEK TESTING SERVICES Internal photos FCC ID: ACJ96NKX-TGWA40 INTERTEK TESTING SERVICES Internal photos FCC ID: ACJ96NKX-TGWA40 INTERTEK TESTING SERVICES Internal photos FCC ID: ACJ96NKX-TGWA40 INTERTEK TESTING SERVICES Internal photos FCC ID: ACJ96NKX-TGWA40 INTERTEK TESTING SERVICES Internal photos FCC ID: ACJ96NKX-TGWA40

INTERTEK TESTING SERVICES FCC ID: ACJ96NKX-TGWA40 RF exposure - 1 of 1 For Standalone SAR test exclusion consideration, when the corresponding SAR Exclusion Threshold requirement in KDB 447498 is satisfied, standalone SAR evaluation for general population exposure conditions, by measurement or numerical simulation is not required. Description the tested model: KX-TGWA40 EUT Description : DECT Cordless Base Station - Deskset Model : KX-TGWA40 Operating Configuration(s) : Body-worn Operating mode (s) : Data Transmission Device Category : Portable Device Tx Frequency : 1921.536 – 1928.448 MHz Production tolerance : 16 dBm (Minimum) to 20.5 dBm (Maximum) Antenna gain : 0 dBi = 1.00 (num gain) Maximum source-based time- averaging duty factor : 4.2% = (1/24 x100%) Minimum separation distance : 5 mm Applicable FCC KDB : FCC KDB 447498 D01 FCC KDB 865664 D02 From above data, the source-based time-averaging output power is as follow: The Maximum Conducted Power = 20.5 dBm = 112.2 mW The Maximum conducted Power source-based time-averaging output power = (112.2 * 0.042) mW = 4.71 mW In the frequency range of 100MHz to 6GHz and test separation distance ≤ 50mm, the SAR Exclusion Threshold will be determined as follow, The SAR exclusion threshold = ( ) )(/0 .3GHzFTD × = 10.80 mW where TD = 5 mm and F(GHz) = 1.928 GHz Conclusion Since the calculated conducted source-based time-averaged output power is 4.71 mW, which is less than the SAR Exclusion Threshold at 5mm test separation distance 10.80 mW for general population and uncontrolled exposure, standalone SAR evaluation for general population exposure conditions, by measurement or numerical simulation is not required.

2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong SAR, China. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 53 TEST REPORT Report Number: 19110149HKG-001 Application For Original Grant of 47 CFR Part 15 Certification Unlicensed Personal Communication Service Devices (Deskset) FCC ID: ACJ96NKX-TGWA40 Prepared and Checked by: Approved by: Signed On File Leung Chiu Kuen, Stanley Engineer Tang Kwan Mo, Jess Lead Engineer Date: Decemebr 24, 2019 TEST REPORT Panasonic Corporation of North America Intertek Report No: 19110149HKG-001 Page 2 of 53 GENERAL INFORMATION Grantee: Panasonic Corporation of North America Grantee Address: Two Riverfront Plaza, 9th Floor, Newark, NJ 07102-5490 United States FCC Specification Standard: FCC Part 15, October 1, 2018 Edition FCC ID: ACJ96NKX-TGWA40 FCC Model(s): KX-TGWA40 Type of EUT: Unlicensed Personal Communications Service Devices Description of EUT: DECT Cordless Base Station - Deskset Serial Number: N/A Sample Receipt Date: November 06, 2019 Date of Test: November 06, 2019 to December 13, 2019 Report Date: Decemebr 24, 2019 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Conclusion: Test was conducted by client submitted sample. The submitted sample as received complied with the 47 CFR Part 15 Certification. TEST REPORT Panasonic Corporation of North America Intertek Report No: 19110149HKG-001 Page 3 of 53 TABLE OF CONTENTS 1.0 TEST RESULTS SUMMARY & STATEMENT OF COMPLIANCE ............................................ 5 1.1 Summary of Test Results ................................................................................................ 5 1.2 Statement of Compliance .............................................................................................. 6 2.0 GENERAL DESCRIPTION ................................................................................................ 7 2.1 Product Description......................................................................................................... 7 2.2 Technical Description ...................................................................................................... 7 2.3 Test Methodology ........................................................................................................... 7 2.4 Test Facility ..................................................................................................................... 7 3.0 SYSTEM TEST CONFIGURATION .................................................................................... 8 3.1 Justification ..................................................................................................................... 8 3.2 Radiated Emission Test Setup ......................................................................................... 9 3.3 AC Line Conducted Emission Test Setup ........................................................................ 10 3.4 Conducted Emission Test Configuration ........................................................................ 11 3.5 Conducted Monitoring and Operational Test Configuration ......................................... 11 3.6 EUT Exercising Software ................................................................................................ 11 3.7 Details of EUT and Description of Accessories ............................................................... 12 3.8 Measurement Uncertainty ............................................................................................ 12 4.0 MEASUREMENT RESULTS ........................................................................................... 13 4.1 Antenna Requirement ................................................................................................... 13 4.2 Digital Modulation Techniques...................................................................................... 13 4.3 Emission Bandwidth ...................................................................................................... 14 4.4 Directional Gain of the Antenna .................................................................................... 16 4.5 Peak Transmit Power .................................................................................................... 17 4.6 Power Spectral Density ................................................................................................. 19 4.7 Automatic Discontinuation of Transmission .................................................................. 21 4.8 Unwanted Emission Inside the Sub-Band ...................................................................... 22 4.9 Emissions Outside the Sub-Band ................................................................................... 25 4.9.1 Radiated Emissions Configuration Photographs ................…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICES The Worst Case Configuration Photographs FCC ID: ACJ96NKX-TGWA40 Radiated Emission Front View Rear View INTERTEK TESTING SERVICES The Worst Case Configuration Photographs FCC ID: ACJ96NKX-TGWA40 AC Conducted Emission Front View Side View 1 INTERTEK TESTING SERVICES The Worst Case Configuration Photographs FCC ID: ACJ96NKX-TGWA40 AC Conducted Emission Side View 2