ACJ9TGCF-081Panasonic Handheld Display with WLAN & Bluetooth

Read Me First Please read these instructions carefully before using this product and save this manual for future use. E D F Wireless Display Model No. CF-08 Read Me First .................................................................................. 2 ENGLISH OPERATING INSTRUCTIONS Contents ........................................................................................ 13 DEUTSCH BEDIENUNGSANLEITUNG Inhalt .............................................................................................. 61 FRANÇAIS INSTRUCTIONS D’UTILISATION Sommaire..................................................................................... 110 2 Read Me First Read Me First Federal Communications Commis- sion Radio Frequency Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to cor- rect the interference by one or more of the following measures: zReorient or relocate the receiving antenna. zIncrease the separation between the equipment and receiver. zConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. zConsult the Panasonic Service Cen- ter or an experienced radio/TV tech- nician for help. Warning To assure continued compliance, use only shielded interface cables when connecting to a wireless display or peripheral. Also, any changes or modi- fications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interfer- ence received, including interference that may cause undesired operation. Responsible Party: Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Tel No: 1-800-LAPTOP5 (1-800-527-8675) FCC RF Exposure Warning: zThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. zThis equipment must be installed and operated in accordance with provided instructions and minimum 1.5 cm spacing must be provided between antenna and all person’s body (excluding extremities of hands, wrist and feet) during wire- less modes of operation. zThis transmitter must not be co- located or operated in conjunction with any other antenna or transmitter. Models for U.S.A. 3 Read Me First Notice for the products using LCD This product uses one or more fluores- cent lamps containing a small amount of mercury. It also contains lead in some components. Disposal of these materi- als may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org/> For Use in Motor Vehicle Warning: Wireless display may be installed in a motor vehicle and visible to the driver only if used to support vehicle related functions such as vehicle infor- mation, system control, rear or side observation and navigation. If used for entertainment purpose, such as televi- sion reception or video play, it must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Check with individual state/provincial laws to determine lawful use of this product while operating within a motor vehicle. Pour L’utilisation Dans Un Véhicule Motorisé Avertissement : L’ordinateur bloc-notes peut être installé dans un véhicule motorisé et dans le champ de vision du conducteur uniquement en tant que dis- positif d’aide aux fonctions du véhicule, comme par exemple pour fournir des informations sur le véhicule, comme dis- positif de contrôle de système, pour l’observation à l’arrière ou sur les côtés du véhicule, ainsi que pour fournir de l’information routière. Pour toute utilisa- tion à fin de divertissement, comme par exemple pour regarder la télévision ou jouer à des jeux vidéo, il doit être installé à l’arrière du siège du conduc- teur, en un emplacement où il ne sera pas visible, ni directement ni indirecte- ment, pour le conducteur du véhicule motorisé. Vérifiez les lois fédérales et nationales qui régissent l’utilisation légale de cet appareil à l’intérieur d’un véhicule motorisé. Models for U.S.A./Canada Models for Canada Industry Canada This product complies with RSS210 Industry Canada. Operation is subject to the following two conditions; (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 4 Read Me First Read Me First Warning This apparatus must be earthed for your safety. To ensure safe operation the three-pin plug must be inserted only into a stan- dard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equip- ment must be threecore and be cor- rectly wired to provide connection to earth. Wrongly wired extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if you have any doubt about the effective earthing of the power point, con…

Text truncated - open the document above for the full version.

Panasonic Corporation of North America Three Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division March 17, 2006 ITPD-05-F039A Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Authority to Act as FCC Agent and Request for Confidentiality Panasonic Handheld Wireless Display, Model CF-081 With Murata BT and Sychip WLAN(b) TCB Certification for FCC ID: ACJ9TGCF-081 To Whom It May Concern: On behalf of Panasonic Corporation of North America, we herby authorize PCTEST Engineering Laboratory, Inc., to act on our behalf in matters relating to FCC equipment authorization, including the signing of documents relating to these matters. Any and all acts carried out by PCTEST on our behalf shall have the same effect as acts of our own. This project represents Portable Handheld Wireless Display, Model CF-08mk1 with Intel CPU type PXA270 at 312 MHz clock speed to be marketed under FCC ID: ACJ9TGCF-081. This product will be marketed with the following two co-located transmitters: (1) Murata Bluetooth Model LBMA46LBA3 with Part 15C operation within 2402~2480 MHz at 19 mW conducted output; and (2) Sychip 2.4 GHz WLAN(b), Model WLAN6065EBC2-HL-TR-01 with Part 15C operation within 2412~2462 MHz at 33.2 mW conducted RF output. This product’s LCD may be operated in either portrait and landscape configuration. The highest reported SAR values at zero spacing between antenna-to-body were: (1) Bluetooth in Tablet Body Position was .181 w/kg; and (2) WLAN in Tablet Body Position was 1.24 W/kg. This PC contains BlueTooth TX/RX Pattern Inverted F-type antenna with 2.44 dBi max antenna gain and WLAN TX/RX Pattern Inverted F-type antenna with max 2.0 dBi antenna gain. In accordance with provisions of Section 0.457(d) of the Commission’s Rules and Section 552(b)(4) of the Freedom of Information Act, we request permanent confidentiality for transmitter’s exhibits which contain Operation Description, Parts Lists, Block Diagram and Schematic Diagram. The BT and WLAN transmitters are not user adjustable and are not provided with Tune-Up Procedure. These exhibits contain proprietary, confidential and trade secrets material, which would not be routinely made available for public inspection. Also, in accordance with FCC Public DA 04-1705, we request short-term confidentiality for exhibits which contain External Photographs, Internal Photographs and User Manual. These exhibits contain pre-market information, which could give our competitors unfair advantage should this information be released before this product is actually introduced into the common marketplace. Sincerely yours, Richard Mullen Richard Mullen Group Manager

< CF-08 Photo > 1) CF-08 Top View Top View WLAN Antenna BlueTooth Antenna 2) CF-08 Bottom View Bottom View

CONFIDENTIAL PROPERTY OF PCTEST FREQUENCY HOPPING SPREAD SPECTRUM (FHSS), FCC RULE PART 15.247 PCTEST LAB TEST REPORT 15.247 FCC CERTIFICATION REPORT Reviewed by: Quality Manager Filename: 0601310060 Test Dates: Feb. 7-8, 2006 EUT Type: Panasonic Toughbook w/ Murata Bluetooth & Sychip WLAN FCC ID: ACJ9TGCF-081 Page 30 of 36 © 2006 PCTEST Engineering Laboratory, Inc. EXHIBIT B – Labeling Requirements Sample Label & Location New Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The sample label shown below shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the trade name, FCC ID, and the FCC logo must be displayed on the device per Section 15.19 (b)(2). CONFIDENTIAL PROPERTY OF PCTEST FREQUENCY HOPPING SPREAD SPECTRUM (FHSS), FCC RULE PART 15.247 PCTEST LAB TEST REPORT 15.247 FCC CERTIFICATION REPORT Reviewed by: Quality Manager Filename: 0601310060 Test Dates: Feb. 7-8, 2006 EUT Type: Panasonic Toughbook w/ Murata Bluetooth & Sychip WLAN FCC ID: ACJ9TGCF-081 Page 31 of 36 © 2006 PCTEST Engineering Laboratory, Inc. EXHIBIT B – Labeling Requirements (Cont.) Sample Label & Location FCC ID LABEL

3) WLAN & BlueTooth Card Position Inside View WLAN Antenna BlueTooth Antenna WLAN & BlueTooth Card 4) Module photo WLAN&BlueTooth Card Top View WLAN Module WLAN&BlueTooth Card Bottom View BlueTooth Module Sychip WLAN Module Top View without shield Note: WLAN Bottom is no component Murata BlueTooth Module Top View without shield Note: WLAN Bottom is no component 5) Antenna position & photo BlueTooth Antenna View WLAN Antenna View BlueTooth Antenna WLAN Antenna

PCTEST ENGINEERING LABORATORY, INC. 6660 – B Dobbin Road • Columbia, MD 21045 • USA Telephone 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com (email: [email protected]) CERTIFICATE OF COMPLIANCE (SAR EVALUATION) PCTEST SAR REPORT FCC CERTIFICATION Reviewed by: Quality Manager SAR Filename: 0601310059 Test Dates: February 7-8, 2006 Phone Type: Panasonic Notebook PC w/ Sychip WLAN & Murata Bluetooth FCC ID: ACJ9TGCF-081 Page 1 of 23 © 2006 PCTEST Engineering Laboratory, Inc APPLICANT NAME & ADDRESS: DATE & LOCATION OF TESTING: Panasonic Corporation of North America Dates of Tests: February 7-8, 2006 One Panasonic Way, 4B-8 Test Report S/N: 0512280871 Secaucus, NJ 07094 Test Site: PCTEST Lab, Columbia MD Project No.: ITPD-05-F039A FCC ID: ACJ9TGCF-081 APPLICANT: Matsushita Electric Industrial Co., Ltd. EUT Type: Notebook PC w/ Sychip WLAN(b) and Murata Bluetooth Module Tx/Rx Frequency: 2412 – 2462 MHz (DSSS)/ 2402 – 2480 MHz (DSS) Max. RF Output Power: 0.033 W Conducted (2.4 GHz DSSS); 12.75 dBm Peak Conducted (2.4 GHz DSS) Max. SAR Measurement: 1.24 W/kg WLAN(b) (2450 MHz) Body SAR, Tablet Position 0.181 W/kg Bluetooth (2450 MHz) Body SAR, Tablet Position Trade Name/Model(s): CF-08 FCC Classification(s): Digital Transmission System (DTS) Unlicensed National Information Infrastructure (NII) Licensed Portable Transmitter Held to Ear (PCE) FCC Rule Part(s): §2.1093; FCC/OET Bulletin 65 Supplement C [July 2001] Application Type: Certification Test Device Serial No.: identical prototype [S/N: #1] This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C (2001) and IEEE Std. 1528 - 2003. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Grant Conditions: Output power listed is Conducted. SAR compliance for body-worn operating configuration is based on a separation distance of 0.0 cm between the bottom of the unit and the body of the user. End-users must be informed of the body-worn operating configurations for satisfying RF exposure compliance. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. PCTEST SAR REPORT FCC CERTIFICATION Reviewed by: Quality Manager SAR Filename: 0601310059 Test Dates: February 7-8, 2006 Phone Type: Panasonic Notebook PC w/ Sychip WLAN & Murata Bluetooth FCC ID: ACJ9TGCF-081 Page 2 of 23 © 2006 PCTEST Engineering Laboratory, Inc TABLE OF CONTENTS 1. INTRODUCTION / SAR DEFINITION......................................................................................3 2. SAR MEASUREMENT SETUP.................................................................................................4 3. DASY4 E-FIELD PROBE SYSTEM.............................................................................................5 4. Probe Calibration Process........................................................................................................6 5. PHANTOM & EQUIVALENT TISSUES......................................................................................7 6. TEST SYSTEM SPECIFICATIONS.............................................................................................8 7. DOSIMETRIC ASSESSMENT & PHANTOM SPECS.......................................................................9 8. DEFINITION OF REFERENCE POINTS...................................................................................10 9. TEST CONFIGURATION POSITIONS.....................................................................................11 10. ANSI/IEEE C95.1 - 1992 RF EXPOSURE LIMITS.......................................................................12 11. MEASUREMENT UNCERTAINTIES...................................................................................13-14 12. SYSTEM VERIFICATION.................................................................................................15-16 13. SAR TEST DATA SUMMARY................................................................................................16 14. SAR DATA SUMMARY...................................................................................................17-35 15. SAR TEST EQUIPMENT......................................................................................................36 16. CONCLUSION.................................................................................................................22 17. REFERENCES...................................................................................................................23 PCTEST SAR REPORT FCC CERTIFICATION Reviewed by: Quality Manager SAR Filename: 0601310059 Test Dates: February 7-8, 2006 Phone Type: Panasonic Notebook PC w/ Sychip WLAN & Murata Bluetooth FCC ID: ACJ9TGCF-081 Page 3 of 23 © 2006 PCTEST Engineering Laboratory, Inc 1. INTRODUCTION / SAR DEFINITION The FCC has adopted the guidelines for evaluating the environmental effects of radiofrequency radiation in ET Docket 93-62 on Aug. 6, 1996 to protect the public and workers from the potential hazards of RF emissions due to FCC-regulated portable devices.[1] The safety limits used for the environmental evaluation measurements are based on the criteria published by the American National Standards Institute (ANSI) for localized specific absorption rate (SAR) in IEEE/ANSI C95.1-1992 Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. (c) 1992 by the Institute of Electrical…

Text truncated - open the document above for the full version.

© 2006 PCTEST Engineering Laboratory, Inc. PCTEST ENGINEERING LABORATORY, INC. 6660 – B Dobbin Road • Columbia, MD 21045 • USA Telephone 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com (email: [email protected]) CERTIFICATE OF COMPLIANCE MANUFACTURER NAME & ADDRESS: DATE & LOCATION OF TESTING: Panasonic Corporation of North America Date(s) of Tests: February 7-8, 2006 One Panasonic Way, 4B-8 Test Report S/N: 0601310060 Secaucus, NJ 07094 Test Site: PCTEST Lab, Columbia, MD Project No.: ITPD-05-F039A FCC ID: ACJ9TGCF-081 APPLICANT: Panasonic Corporation of North America SUMMARY: Model No.: CF-08 Equipment EUT Type: Panasonic Handheld Wireless Display Model: CF-08 w/ Sychip WLAN and Murata Bluetooth Module Max. Output Power: 33.2 mW Conducted Frequency Range: 2412 - 2462 MHz FCC Classification: FCC Part 15 Digital Transmission System (DTS) FCC Rule Part(s): Parts 15.247; ANSI C-63.4-2001 Test Device Serial No.: S/N: 1 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C-63.4-2001. If the EUT contains any additional embedded transmitters, then those transmitters were active during all tests. The JBC portion of this EUT is covered in the DOC report. Grant Conditions: Power output is conducted. This device has been tested for SAR compliance for portable configurations. This device must not be co-located or operating with any other antenna or transmitter. End- users must be provided with operating conditions for satisfying RF exposure compliance. I authorize and attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Spread Spectrum Transceiver (DTS), FCC Rule Part 15.247 PCTEST LAB TEST REPORT 15.247 FCC CERTIFICATION REPORT Reviewed by: Quality Manager Filename: 0601310060 Test Dates: Fe. 7-8, 2006 EUT Type: Panasonic Wireless Handheld Display w/ Sychip WLAN & Murata Bluetooth FCC ID: ACJ9TGCF-081 Page i of i © 2006 PCTEST Engineering Laboratory, Inc. CONFIDENTIAL PROPERTY OF PCTEST TABLE OF CONTENTS ATTESTATION STATEMENTS.............................................................................................................................1 FCC PART 15.247 MEASUREMENT REPORT COVER PAGE..........................................................................2 1.0 INTRODUCTION...................................................................................................................3 1.1 EVALUATION PROCEDURE.......................................................................................................................................3 1.2 SCOPE.................................................................................................................................................................3 1.3 PCTEST TEST LOCATION..........................................................................................................................................3 2.0 PRODUCT INFORMATION.......................................................................................................4 2.1 EQUIPMENT DESCRIPTION........................................................................................................................................4 2.2 ENCLOSURE.........................................................................................................................................................4 2.3 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS..............................................................................................................4 3.0 DESCRIPTION OF TEST...........................................................................................................5 3.1 CONDUCTED EMISSIONS..........................................................................................................................................5 3.2 RADIATED EMISSIONS..............................................................................................................................................6 4.0 ANTENNA REQUIREMENTS......................................................................................................7 5.0 TEST EQUIPMENT CALIBRATION DATA.......................................................................................8 EXHIBIT A. SUMMARY OF TEST RESULTS..............................................................................................................................9 EXHIBIT A. 6dB BANDWIDTH MEAUREMENT........................................................................................................................10-12 EXHIBIT A. OUTPUT POWER MEASUREMENT......................................................................................................................13-15 EXHIBIT A. POWER SPECTRAL DENSITY..............................................................................................................................16-18 EXHIBIT A. BANDEDGE........................................................................................................................................................19 EXHIBIT A. RADIATED FUNDAMENTAL & HARMONIC MEASUREMENTS................................................................................20-22 EXHIBIT A. RADIATED SPURIOUS MEASUREMENTS..............................................................................................................23 EXHIBIT A. RADIATED RESTRICTED BAND MEASUREMENTS..........................................................................................…

Text truncated - open the document above for the full version.

Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08

Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08 Panasomic FCC ID: ACJ9TGCF-081 EUT Photographs © 2006 PCTEST Lab. Notebook PC w/ Sychip WLAN & Murata Bluetooth Model: CF-08