ACJ9TGCF-Y71Personal Computer Model CF-Y71

Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division October 9, 2007 ITPD-07-F029A: BT Part 15C / DSS / EA950228 ITPD-07-F029B: WLAN Part 15C / DTS / EA125612 ITPD-07-F029C: UNII Part 15E / NII / EA683175 ITPD-07-F029D: EVDO Parts 22H, 24E / PCB / EA783869 Dear Linda Elliott / FCC Application Processing Branch Applicant: Panasonic Corporation of North America FCC ID: ACJ9TGCF-Y71 Form 731 Confirmation Numbers: EA950228, EA125612, EA683175, EA783869 Date of Original E-Mail: 10/05/2007 Correspondence Reference Numbers: 33929, 33931, 33930, 33932 FCC Comment: The filing fee must be submitted before processing can continue on the above referenced application. Failure to comply with this request within 30 days of today's notice, may result in application dismissal pursuant to our Public Notice DA00-661, dated March 24, 2000. If, however, you have paid the filing fee, please clarify. Response: Please be advised four (4) FCC fee checks were mailed to FCC on, or about October 5, 2007. Sincerely yours, Richard Mullen Group Manager

< CF-Y7 EVDO Rev.A + Taiyo Yuden BT + WLANabg photo> 1. Front View

EVDO re vA T X /R X a ntenna W L AN TX/RX a ntenna (A ux ) W L AN TX/RX antenna (Main) Bluetooth a ntenna

<FCC ID & DoC LABEL for CF-Y7 EVDO Rev.A + Taiyo Yuden BT + WLANabg> 1) FCCID Label 2) FCC DoC Logo FCC ID: ACJ9TGCF-Y71 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID Label Position FCC DoC Position

2. Module Position WLAN Module BlueTooth Module (Reverse side of PWB) EVDO Rev.A Module 3. Module Photo 1) WLAN WLAN Exterior Top View WLAN Exterior Bottom View WLAN inside Top View WLAN inside Bottom View 2) BlueTooth BlueTooth Card Top View BlueTooth Card Bottom View BlueTooth Module inside Top View BlueTooth Module inside Bottom View FCCID:WM3945ABG 3) EVDO Rev.A Photo EVDO Top View EVDO Bottom View EVDO Inside Top View EVDO Inside Bottom View 4) Antenna Position WLAN Aux TX/RX Antenna BlueTooth TX/RX Antenna WLAN Main TX/RX Antenna EVDO Main TX/RX Antenna EVDO Aux RX only Antenna WLAN Main TX/RX Antenna WLAN AUX TX/RX Antenna BlueTooth TX/RX Antenna EVDO Main TX/RX Antenna EVDO AUX RX only Antenna 5) Antenna Specification WLAN Main TX/RX Antenna: Inverted-F type: 2.00dBi(2.4GHz)max 4.17dBi(5GHz) max WLAN Aux TX/RX Antenna: Inverted-F type: 2.89dBi(2.4GHz)max 4.64dBi(5GHz) max BlueTooth Antenna: Inverted-F type: 4.38dBi max EVDO Main TX/RX Antenna: Inverted-F type:2.50dBi max EVDO Aux TX/RX Antenna: Inverted-F type:RX only

Reviewed by: FCC ID: ACJ9TGCF-Y71 CERTIFICATION REPORT Quality Manager Filename: Test Dates: EUT Type: 0708210907.ACJ 09/07/07 - 09/17/07 Notebook PC with BT, W LAN and EVDO Page 1 of 21 © 2007 PCTEST Engineering Laboratory, Inc. REV 4.3B 09/18/07 Applicant Name: Date of Testing: Panasonic Corporation of North America 09/07/07 - 09/17/07 One Panasonic Way, 4B-8 Test Site/Location: Secaucus, NJ 07094 PCTEST Lab, Columbia, MD, USA United States Test Report Serial No.: 0708210907.ACJ FCC ID: ACJ9TGCF-Y71 APPLICANT: PANASONIC CORPORATION OF NORTH AMERICA EUT Type: Notebook PC with BT, WLAN and EVDO Application Type: Certification FCC Rule Part(s): §2.1093; FCC/OET Bulletin 65 Supplement C [July 2001] FCC Classification: Digital Transmission System (DTS) Model(s): CF-Y7 Tx Frequency: 2412 - 2462 MHz (WLAN 802.11b) 5180 - 5320 MHz (WLAN 802.11a) 826.40 - 846.60 MHz (Cellular WCDMA) (WLAN 802.11a) 2402 - 2480 MHz ( Bluetooth) Conducted Power: 12.72 dBm 802.11b 12.55 dBm 802.11g 13.1 dBm 5.2 GHz 802.11a 13.79 dBm 802.11a 5.8 GHz 13.66 dBm Bluetooth Max. SAR Measurement: 0.0908 W/kg 802.11b Body SAR 0.144 W/kg 802.11a 5.2GHz Body SAR 0.146 W/kg 802.11a 5.3GHz Body SAR 0.0829 W/kg 802.11a 5.8GHz Body SAR Test Device Serial No.: Pre-Production [S/N: 7GKSA00062] This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-2005 and has been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C (2001) and IEEE Std. 1528-2003. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. PCTEST ENGINEERING LABORATORY, INC. 6660-B Dobbin Road, Columbia, MD 21045 USA Tel. 410.290.6652 / Fax 410.290.6554 http://www.pctestlab.com CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Reviewed by: FCC ID: ACJ9TGCF-Y71 CERTIFICATION REPORT Quality Manager Filename: Test Dates: EUT Type: 0708210907.ACJ 09/07/07 - 09/17/07 Notebook PC with BT, W LAN and EVDO Page 2 of 21 © 2007 PCTEST Engineering Laboratory, Inc. REV 4.3B 09/18/07 TABLE OF CONTENTS 1 INTRODUCTION ........................................................................................................................ 3 2 TEST SITE LOCATION............................................................................................................... 4 3 SAR MEASUREMENT SETUP ................................................................................................... 5 4 DASY E-FIELD PROBE SYSTEM............................................................................................... 7 5 PROBE CALIBRATION PROCESS............................................................................................. 8 6 PHANTOM AND EQUIVALENT TISSUES .................................................................................. 9 7 DOSIMETRIC ASSESSMENT & PHANTOM SPECS................................................................ 10 8 TEST CONFIGURATION POSITIONS ...................................................................................... 11 9 ANSI/IEEE C95.1-2005 RF EXPOSURE LIMITS...................................................................... 13 10 MEASUREMENT UNCERTAINTIES......................................................................................... 14 11 SYSTEM VERIFICATION ......................................................................................................... 15 12 SAR DATA SUMMARY............................................................................................................. 16 13 EQUIPMENT LIST.................................................................................................................... 18 14 CONCLUSION.......................................................................................................................... 19 15 REFERENCES ......................................................................................................................... 20 Reviewed by: FCC ID: ACJ9TGCF-Y71 CERTIFICATION REPORT Quality Manager Filename: Test Dates: EUT Type: 0708210907.ACJ 09/07/07 - 09/17/07 Notebook PC with BT, W LAN and EVDO Page 3 of 21 © 2007 PCTEST Engineering Laboratory, Inc. REV 4.3B 09/18/07 1 INTRODUCTION The FCC has adopted the guidelines for evaluating the environmental effects of radio frequency (RF) radiation in ET Docket 93-62 on Aug. 6, 1996 to protect the public and workers from the potential hazards of RF emissions due to FCC-regulated portable devices.[1] The safety limits used for the environmental evaluation measurements are based on the criteria published by the American National Standards Institute (ANSI) for localized specific absorption rate (SAR) in IEEE/ANSI C95.1-2005 Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz[2] and Health Canada RF Exposure Guidelines Safety Code 6 [26]. The measurement procedure described in IEEE/ANSI C95.3-2002 Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields - RF and Microwave [3] is used for guidance in measuring the Specific Absorption Rate (SAR) due to the RF radiation exposure from the Equipment Under Test (EUT). These criteria for SAR evaluation are similar to those recommended by the International Committee for Non-Ionizing Radiation Protection (ICNIRP) in Biological Effects and Exposure Criteria for Radiofrequency Electromagnetic Fields,” Report No. Vol 74. SAR is a measure of the rate of energy…

Text truncated - open the document above for the full version.

APPENDIX A: SAR TEST DATA PCTEST ENGINEERING LABORATORY, INC. DUT: CF-Y7; Type: Notebook PC with WLAN abg, Bluetooth and EVDO; SN:7GKSA00062 Communication System: IEEE 802.11b; Frequency: 2462 MHz; Duty Cycle: 1:1 Medium: 2450 Muscle ( σ = 1.99 mho/m, ε r = 55.12, ρ = 1000 kg/m 3 ) Phantom section: Flat Section Test Date: 09-07-2007; Ambient Temp: 23.9°C; Tissue Temp: 21.8°C Probe: EX3DV4 - SN3589; ConvF(6.37, 6.37, 6.37); Calibrated: 5/28/2007 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn704; Calibrated: 5/25/2007 Phantom: SAM Main; Type: SAM 4.0; Serial: TP-1406 Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172 Mode: IEEE 802.11b, Laptop position, Ch.11, 1Mbps, Main Antenna Area Scan (7x19x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 7.06 V/m Peak SAR (extrapolated) = 0.194 W/kg SAR(1 g) = 0.091 mW/g; SAR(10 g) = 0.045 mW/g 0 dB = 0.115mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-Y7; Type: Notebook PC with WLAN abg, Bluetooth and EVDO; SN:7GKSA00062 Communication System: IEEE 802.11b; Frequency: 2462 MHz; Duty Cycle: 1:1 Medium: 2450 Muscle ( σ = 1.99 mho/m, ε r = 55.12, ρ = 1000 kg/m 3 ) Phantom section: Flat Section Test Date: 09-07-2007; Ambient Temp: 23.9°C; Tissue Temp: 21.8°C Probe: EX3DV4 - SN3589; ConvF(6.37, 6.37, 6.37); Calibrated: 5/28/2007 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn704; Calibrated: 5/25/2007 Phantom: SAM Main; Type: SAM 4.0; Serial: TP-1406 Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172 Mode: IEEE 802.11b, Laptop position, Ch.11, 1Mbps, Auxillary Antenna Area Scan (7x19x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 4.27 V/m Peak SAR (extrapolated) = 0.131 W/kg SAR(1 g) = 0.054 mW/g; SAR(10 g) = 0.021 mW/g 0 dB = 0.086mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-Y7; Type: Notebook PC with WLAN abg, Bluetooth and EVDO; SN:7GKSA00062 Communication System: Bluetooth; Frequency: 2441 MHz; Duty Cycle: 1:1 Medium: 2450 Muscle ( σ = 1.99 mho/m, ε r = 55.12, ρ = 1000 kg/m 3 ) Phantom section: Flat Section Test Date: 09-07-2007; Ambient Temp: 23.9°C; Tissue Temp: 21.8°C Probe: EX3DV4 - SN3589; ConvF(6.37, 6.37, 6.37); Calibrated: 5/28/2007 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn704; Calibrated: 5/25/2007 Phantom: SAM Main; Type: SAM 4.0; Serial: TP-1406 Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172 Mode: Bluetooth, Laptop position, Ch 39, Fixed Antenna Area Scan (7x19x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 1.30 V/m Peak SAR (extrapolated) = 0.090 W/kg SAR(1 g) = 0.047 mW/g; SAR(10 g) = 0.026 mW/g 0 dB = 0.057mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-Y7; Type: Notebook PC with WLAN abg, Bluetooth and EVDO; SN:7GKSA00062 Communication System: IEEE 802.11a; Frequency: 5240 MHz; Duty Cycle: 1:1 Medium: 5300 Muscle ( σ = 5.22 mho/m, ε r = 50.14, ρ = 1000 kg/m 3 ) Phantom section: Flat Section Test Date: 09-12-2007; Ambient Temp: 23.5°C; Tissue Temp: 21.6°C Probe: EX3DV4 - SN3589; ConvF(4.12, 4.12, 4.12); Calibrated: 5/28/2007 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn704; Calibrated: 5/25/2007 Phantom: SAM Main; Type: SAM 4.0; Serial: TP-1406 Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172 Mode: IEEE 802.11a, Laptop position, Ch.48, 6Mbps, Main Antenna Area Scan (10x28x1): Measurement grid: dx=10mm, dy=10mm Zoom Scan (8x8x8)/Cube 0: Measurement grid: dx=4.3mm, dy=4.3mm, dz=3mm Reference Value = 4.55 V/m Peak SAR (extrapolated) = 0.471 W/kg SAR(1 g) = 0.144 mW/g; SAR(10 g) = 0.053 mW/g 0 dB = 0.211mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-Y7; Type: Notebook PC with WLAN abg, Bluetooth and EVDO; SN:7GKSA00062 Communication System: IEEE 802.11a; Frequency: 5240 MHz;Duty Cycle: 1:1 Medium: 5300 Muscle ( σ = 5.22 mho/m, ε r = 50.14, ρ = 1000 kg/m 3 ) Phantom section: Flat Section Test Date: 09-12-2007; Ambient Temp: 23.5°C; Tissue Temp: 21.6°C Probe: EX3DV4 - SN3589; ConvF(4.12, 4.12, 4.12); Calibrated: 5/28/2007 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn704; Calibrated: 5/25/2007 Phantom: SAM Main; Type: SAM 4.0; Serial: TP-1406 Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172 Mode: IEEE 802.11a, Laptop position, Ch.48, 6Mbps, Auxillary Antenna Area Scan (10x28x1): Measurement grid: dx=10mm, dy=10mm Zoom Scan (8x8x8)/Cube 0: Measurement grid: dx=4.3mm, dy=4.3mm, dz=3mm Reference Value = 5.14 V/m Peak SAR (extrapolated) = 1.19 W/kg SAR(1 g) = 0.135 mW/g; SAR(10 g) = 0.050 mW/g 0 dB = 0.179mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-Y7; Type: Notebook PC with WLAN abg, Bluetooth and EVDO; SN:7GKSA00062 Communication System: IEEE 802.11a; Frequency: 5260 MHz; Duty Cycle: 1:1 Medium: 5300 Muscle ( σ = 5.22 mho/m, ε r = 50.14, ρ = 1000 kg/m 3 ) Phantom section: Flat Section Test Date: 09-12-2007; Ambient Temp: 23.5°C; Tissue Temp: 21.6°C Probe: EX3DV4 - SN3589; ConvF(3.91, 3.91, 3.91); Calibrated: 5/28/2007 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn704; Calibrated: 5/25/2007 Phantom: SAM Main; Type: SAM 4.0; Serial: TP-1406 Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172 Mode: IEEE 802.11a, Laptop position, Ch.52, 6Mbps, Main Antenna Area Scan (10x28x1): Measurement grid: dx=10mm, dy=10mm Zoom Scan (8x8x8)/Cube 0: Measurement grid: dx=4.3mm, dy=4.3mm, dz=3mm Reference Value = 5.33 V/m Peak SAR (extrapolated) = 0.487 W/kg SAR(1 g) = 0.146 mW/g; SAR(10 g) = 0.057 mW/g 0 dB = 0.211mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-Y7; Type: Notebook PC with WLAN abg, Bluetooth and EVDO; SN:7GKSA00062 Communication System: IEEE 802.11a; Frequency: 5260 MHz; Duty Cy…

Text truncated - open the document above for the full version.

Reviewed by: FCC ID: ACJ9TGCF-Y71 FCC Pt. 15.247 WLAN 802.11a/g MEASUREMENT REPORT (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: 0708210908.ACJ September 13 - 14, 2007 Toughbook Model: CF-Y7 Page 1 of 41 © 2007 PCTEST Engineering Laboratory, Inc. REV 1.0WAG 07/12/07 Applicant Name: Date of Testing: Panasonic Corporation of North America September 13 - 14, 2007 One Panasonic Way, 4B-8 Test Site/Location: Secaucus, NJ 07094 PCTEST Lab, Columbia, MD, USA United States Test Report Serial No.: 0708210908.ACJ FCC ID: ACJ9TGCF-Y71 APPLICANT: Panasonic Corporation of North America Model(s): CF-Y7 EUT Type: Toughbook Model: CF-Y7 Max. RF Output Power: 19.14 mW (12.82 dBm) Conducted (g) 23.93 mW (13.79 dBm) Conducted (a) Frequency Range: 2412 - 2462 MHz (DSSS/OFDM) 5745 – 5825 MHz (OFDM) FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15.247 Test Device Serial No.: 7GKSA00061 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C-63.4-2003. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Grant Conditions: Listed output power is conducted. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. PCTEST ENGINEERING LABORATORY, INC. 6660-B Dobbin Road, Columbia, MD 21045 USA Tel. 410.290.6652 / Fax 410.290.6554 http://www.pctestlab.com CERTIFICATE OF COMPLIANCE FCC PART 15.247 Certification Reviewed by: FCC ID: ACJ9TGCF-Y71 FCC Pt. 15.247 WLAN 802.11a/g MEASUREMENT REPORT (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: 0708210908.ACJ September 13 - 14, 2007 Toughbook Model: CF-Y7 Page 2 of 41 © 2007 PCTEST Engineering Laboratory, Inc. REV 1.0WAG 07/12/07 TABLE OF CONTENTS FCC PART 15.247 MEASUREMENT REPORT...................................................................................3 1.0 INTRODUCTION......................................................................................................................................4 1.1 EVALUATION PROCEDURE..................................................................................................................... 4 1.2 SCOPE....................................................................................................................................................... 4 1.3 PCTEST TEST LOCATION........................................................................................................................ 4 2.0 PRODUCT INFORMATION .....................................................................................................................5 2.1 EQUIPMENT DESCRIPTION..................................................................................................................... 5 2.2 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS.................................................................................. 5 2.3 LABELING REQUIREMENTS .................................................................................................................... 5 3.0 DESCRIPTION OF TEST ........................................................................................................................6 3.1 CONDUCTED EMISSIONS........................................................................................................................ 6 3.2 RADIATED EMISSIONS ............................................................................................................................ 7 4.0 ANTENNA REQUIREMENTS ..................................................................................................................8 5.0 TEST EQUIPMENT CALIBRATION DATA..............................................................................................9 6.0 TEST RESULTS ....................................................................................................................................10 6.1 SUMMARY ............................................................................................................................................... 10 6.2 6DB BANDWIDTH MEASUREMENT – 802.11A/G.................................................................................. 11 6.3 OUTPUT POWER MEASUREMENT – 802.11G...................................................................................... 15 6.4 OUTPUT POWER MEASUREMENT – 802.11A (5.8GHZ) ...................................................................... 16 6.5 POWER SPECTRAL DENSITY (802.11A/G) ........................................................................................... 17 6.6 OUT OF BAND EMISSIONS AT THE BAND EDGE................................................................................ 21 6.7 OUT OF BAND EMISSIONS .................................................................................................................... 23 6.8 RADIATED SPURIOUS EMISSION MEASUREMENTS.......................................................................... 29 6.9 RADIATED RESTRICTED BAND EDGE MEASUREMENTS .................................................................. 36 6.10 LINE-CONDUCTED TEST DATA............................................................................................................. 37 7.0 CONCLUSION .......................................................................................................................................41 Reviewed by: FCC ID: ACJ9TGCF-Y71 FCC Pt. 15.247 WLAN 802.11a/g MEASUREMENT REPORT (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: 0708210908.ACJ September 13…

Text truncated - open the document above for the full version.

Reviewed by: FCC ID: ACJ9TGCF-Y71 FCC Pt. 15.247 WLAN 802.11a/g MEASUREMENT REPORT (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: 0708210908-R1.ACJ September 13 - 14, 2007 Toughbook Model: CF-Y7 Page 1 of 41 © 2007 PCTEST Engineering Laboratory, Inc. REV 1.0WAG 07/12/07 Applicant Name: Date of Testing: Panasonic Corporation of North America September 13 - 14, 2007 One Panasonic Way, 4B-8 Test Site/Location: Secaucus, NJ 07094 PCTEST Lab, Columbia, MD, USA United States Test Report Serial No.: 0708210908-R1.ACJ FCC ID: ACJ9TGCF-Y71 APPLICANT: Panasonic Corporation of North America Model(s): CF-Y7 EUT Type: Toughbook Model: CF-Y7 Max. RF Output Power: 19.14 mW (12.82 dBm) Conducted (g) 23.93 mW (13.79 dBm) Conducted (a) Frequency Range: 2412 - 2462 MHz (DSSS/OFDM) 5745 – 5825 MHz (OFDM) FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15.247 Test Device Serial No.: 7GKSA00061 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C-63.4-2003. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. *Note: This revised Test Report (S/N: 0708210908-R1.ACJ) supersedes and replaces the previously issued test report for the same subject EUT for the same type of testing as indicated. Please discard and destroy the previously issued test report (S/N: 0708210908.ACJ) and dispose of if accordingly. Grant Conditions: Listed output power is conducted. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. PCTEST ENGINEERING LABORATORY, INC. 6660-B Dobbin Road, Columbia, MD 21045 USA Tel. 410.290.6652 / Fax 410.290.6554 http://www.pctestlab.com CERTIFICATE OF COMPLIANCE FCC PART 15.247 Certification Reviewed by: FCC ID: ACJ9TGCF-Y71 FCC Pt. 15.247 WLAN 802.11a/g MEASUREMENT REPORT (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: 0708210908-R1.ACJ September 13 - 14, 2007 Toughbook Model: CF-Y7 Page 2 of 41 © 2007 PCTEST Engineering Laboratory, Inc. REV 1.0WAG 07/12/07 TABLE OF CONTENTS FCC PART 15.247 MEASUREMENT REPORT...................................................................................3 1.0 INTRODUCTION......................................................................................................................................4 1.1 EVALUATION PROCEDURE..................................................................................................................... 4 1.2 SCOPE....................................................................................................................................................... 4 1.3 PCTEST TEST LOCATION........................................................................................................................ 4 2.0 PRODUCT INFORMATION .....................................................................................................................5 2.1 EQUIPMENT DESCRIPTION..................................................................................................................... 5 2.2 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS.................................................................................. 5 2.3 LABELING REQUIREMENTS .................................................................................................................... 5 3.0 DESCRIPTION OF TEST ........................................................................................................................6 3.1 CONDUCTED EMISSIONS........................................................................................................................ 6 3.2 RADIATED EMISSIONS ............................................................................................................................ 7 4.0 ANTENNA REQUIREMENTS ..................................................................................................................8 5.0 TEST EQUIPMENT CALIBRATION DATA..............................................................................................9 6.0 TEST RESULTS ....................................................................................................................................10 6.1 SUMMARY ............................................................................................................................................... 10 6.2 6DB BANDWIDTH MEASUREMENT – 802.11A/G.................................................................................. 11 6.3 OUTPUT POWER MEASUREMENT – 802.11G...................................................................................... 15 6.4 OUTPUT POWER MEASUREMENT – 802.11A (5.8GHZ) ...................................................................... 16 6.5 POWER SPECTRAL DENSITY (802.11A/G) ........................................................................................... 17 6.6 OUT OF BAND EMISSIONS AT THE BAND EDGE................................................................................ 21 6.7 OUT OF BAND EMISSIONS .................................................................................................................... 23 6.8 RADIATED SPURIOUS EMISSION MEASUREMENTS.......................................................................... 29 6.9 RADIATED RESTRICTED BAND EDGE MEASUREMENTS .................................................................. 36 6.10 LINE-CONDUCTED TEST DATA............................................................................................................. 37 7.0 CONCLUSION .............…

Text truncated - open the document above for the full version.

PANASONIC FCC ID: ACJ9TGCF-Y71 Model: CF-Y7 SAR Test Setup Photos Notebook PC with WLAN, Bluetooth and EVDO Page 1 of 2 © 2007 PCTEST Lab. REV 2.1 05/24/2007 1. Body SAR, Laptop position, Main Antenna 2. Body SAR, Laptop position, Main Antenna PANASONIC FCC ID: ACJ9TGCF-Y71 Model: CF-Y7 SAR Test Setup Photos Notebook PC with WLAN, Bluetooth and EVDO Page 2 of 2 © 2007 PCTEST Lab. REV 2.1 05/24/2007 3. Body SAR, Laptop position, Auxillary Antenna 4. Body SAR, Laptop position, Auxillary Antenna