AMX-1721BA1Wireless Robotically Controlled Camera System Basestation

Information Guide Lanyard The lanyard is only intended for use with adults. It does not contain a safety breakaway for use with children (under the age of 8). Infrared Interference This product uses IR technology. Direct interference from strong IR sources, such as sun, plasma TVs, and some types of light fixtures, may affect its performance. Remove the interference, or direct the product away from from the IR source. Radio Frequency Interference This product uses 2.4Ghz wireless technology for wireless audio transmission. High saturation of similar technology in the immediate vicinity may degrade audio quality Avoid water Do not expose this product to water or rain, or handle near wet locations. Do not spill food or liquid on the product. In the case that it gets wet, remove batteries and unplug any cables and allow it to fully dry before turning it back on again. Damage due to liquid is not covered under warranty. Avoid operation while driving Do not use this product while driving. Air travel Use of this product may be prohibited while travelling in aircraft as it emits radio frequencies during operation. Acceptable temperatures The product is designed to be used between 0 degrees and 40 degrees C (32 degrees and 104 degrees F). Important Any modifications to the unit, unless expressly approved by the party responsible for compliance, could void the user’s authority to operate the equipment. The product has demonstrated EMC compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components. It is important that you use the compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, televisions and other electronics devices. Canadian Compliance Statement Complies with the Canadian ICED-003 Class B specifications. Cet appareil numerique de la lass B est conforme a la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numerique de la Classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux normes CNR exemptes de licence d’Inustrie Canada. Le fonctionnement est soumis aux deus conditions suivantes: (1) cet appareil ne doit pa provoquer d’interferences et (2) cet appareil doit accepter toute interference, y compris celles susceptibles de provoquer un fonctionnement non souhaite de l’appareil. Warranty This product is guaranteed against manufacturing defects for one (1) year from the original date of purchase. Satarii’s sole obligation in the event of such defects during this period is to repair or replace the defective part or product with a comparable part or product. This is done at Satarii’s sole discretion. Except for such replacement, the sale, or other handling of this product is without warranty, condition or other liability even though the defect or loss is caused by negligence or other fault. Damage resulting from use, misuse, accident, or normal wear and tear is not covered by this or any warranty. Satarii assumes no liability for incidental or consequential damages relating to or resulting from the use of this product or any of its parts. When servicing your warranty request, Satarii may require you to furnish proof of purchase details. Visit www.swivl.com for more information. Attention “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. Carrying and handling Product contains sensitive components. Do not drop, disassemble, microwave, burn, paint or insert foreign objects into device. Do not use if it has been damaged. AC Adapter The product is designed to be used only with the Swivl approved AC Adapter. It can be stored between -20 degrees and 70 degrees C (-4 degrees and 158 degrees F). Low or high temperature conditions might lead the product to temporarily stop working, or working properly. Allow unit to return to room temperature after storage at high or low temperatures before operation. Leaving product in a parked vehicle or in direct sunlight can cause it to exceed the storage or operating temperature ranges. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: • Reorient or locate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into…

Text truncated - open the document above for the full version.

Quick Reference Guide IncludesBatteriesTripod Accessory LanyardUSB Cable Step 1 Open grip Key features Action Button LEDLED Record Button Lock BarAdjustment wheel Grip USB Connector Cable Battery Door Battery Door Step 2 Load batteries 2x AA Batteries 2x AAA Batteries Step 3 Power on base Press and hold the Record button until LED indication as shown Press and hold the Record button until LED indication as shown Step 4 Power on marker Step 5 Horizontal motion Once connected, just move your hand. Press and hold Action button, then move your hand. Step 6 Vertical motion Step 7 Adjusting for your device Turn adjustment wheel to adapt. Tight sliding fit desired. Should not require force. Before continuing ... Step 8  Step 11 For more information on cable use in other device orientations, go to: www.swivl.com/support If lock bar does not stay fully depressed, remove device, tighten adjustment wheel and repeat. Step 9 Attaching your device Step 8 Connecting your device Note: Requires Internet connection. * Remove cable from rear. Follow prompts to download the Swivl app. Wrap cable around base, insert device and depress the lock bar. Screw tripod accessory into the tripod adapter on your camera.Insert similarly to step 9.Step 11 Attaching a camera Step 10 Video Recording To record, simply hit the record button once, and again to stop. Skip Step 11 and proceed to Step 12. Tripod Accessory * For more information, go to www.swivl.com/support Satarii, Inc.1354 El Camino RealSan Carlos, CA 94070www.swivl.comCustomer Support1 888 837 [email protected] * Step 12 Learn more about your MC-00105 TM and © 2012 Satarii Inc. All rights reserved. Swivl, the Swivl logo, Satarii and all other company, product and service names or slogans are trademarks of Satarii, Inc. Patent pending.iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.Designed in California by Satarii, Inc., Printed in China.

Elliott Laboratories is accredited by the A2LA, certificate number 0214.26, to perform the test(s) listed in this report, except where noted otherwise. This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full Elliott Laboratories, LLC an NTS Company 41039 Boyce Road 510‐578‐3500 Phone www.elliottlabs.com Fremont, CA. 94538 510‐440‐9525 Fax Attestation for FCC Declaration of Conformity We, the undersigned, declare that a sample of the Satarii Inc. Swivl Base model SW1721(BA1), FCC ID AMX‐1721BA1 which was received on January 31, 2012 and tested on January 31, 2012 was found to comply with Subpart B of Part 15 of FCC Rules and with Industry Canada Interference Causing Equipment Standard ICES‐003 Issue 4, dated February 2004 for Class B digital devices given the measurement uncertainties detailed in Elliott report R86479. ___________________________ _______________________________ Mark E Hill David Guidotti Staff Engineer Senior Technical Writer

Page 1 of 1 American Certification Body 6731 Whittier Ave, Suite C110 McLean, VA 22101 RE: FCC Applications for Satarii, FCC ID: AMX-1721BA1, AMX-1721MA1 and Industry Canada Applications, IC ID: 10134A-1721BA1 and 10134A-1721MA1 To whom it may concern: The enclosed documents constitute formal submittals and applications for Equipment Authorization and IC Certification for two devices that comprise a wireless robotically controlled camera system. The system is comprised of a base station and a remote unit. Each device is a 2.4GHz transceiver and is seeking authorization pursuant to the following rules: Subpart C of Part 15 of FCC Rules (CFR 47) RSS-Gen Issue 3, December 2010, “General Requirements and Information for the Certification of Radiocommunication Equipment” RSS-210, Issue 8, December 2010, “Low-power Licence-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment” Elliott Laboratories, as duly authorized agent prepared this submittal. A copy of the letter of our appointment as agent is included with the application. If there are any questions or if further information is needed, please contact Elliott Laboratories for assistance. Sincerely, Mark E. Hill Staff Engineer

SCALE 4X A B C D A B C D 1 2 3 4 4 2 1 DWG NO: REV: SHEET: M0-000580A2 Model: SW1721(BA1) SN: SWNNYYWWM#### FCC ID: AMX-1721BA1 IC: 10134A-1721BA1 MC-00058 Designed in CA by Satarii, Inc. Assembled in China Patent Pending

EMC Test Data Client: Contact: Standard: Test Specific Details General Test Configuration Yes Satarii IncJob Number: J86132 Model: Swivl - SW1721(BA1) Basestation, SW1721(MA1) Remote T-Log Number: T86212 Account Manager: Deepa Shetty Vladimir Tetelbaum FCC 15B, FCC 15.247Class: N/A Maximum Permissible Exposure Objective: The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. Date of Test: 2/10/2012 Test Engineer: Mark Hill Calculation uses the free space transmission formula: S = (PG)/(4 πd 2 ) Where: S is power density (W/m 2 ), P is output power (W), G is antenna gain relative to isotropic, d is separation distance from the transmitting antenna (m). Summary of Results Device complies with Power Density requirements at 20cm separation:20cm separation: Modifications Made During Testing No modifications were made to the EUT during testing Deviations From The Standard No deviations were made from the requirements of the standard. T86212 Satarii.xlsMPE CalcPage 1 of 2 EMC Test Data Client: Contact: Standard: Satarii IncJob Number: J86132 Model: Swivl - SW1721(BA1) Basestation, SW1721(MA1) Remote T-Log Number: T86212 Account Manager: Deepa Shetty Vladimir Tetelbaum FCC 15B, FCC 15.247Class: N/A Use: General Antenna:3.3dBi Basetation Cable AntPower Freq.LossGainat AntEIRP MHzdBmmW*dBdBidBmmW 24060.31.103.30.32.27 24382.41.703.32.43.71 2474-0.70.903.3-0.71.84 Remote Cable AntPower Freq.LossGainat AntEIRP MHzdBmmW*dBdBidBmmW 24065.03.203.35.06.76 24383.22.103.33.24.47 24744.42.803.34.45.89 1.000 EUTPower Densit y (S)MPE Limit at 20 cm 0.0011.000 0.0001.000 Powe rat 20 cmat 20 cm mW/cm^2mW/cm^2 0.000 1.000 0.0011.000 mW/cm^2mW/cm^2 0.0011.000 As the output power is below the 20mW EIRP threshold detailed in RSS-102, 2.5.1, the devices are exempt from routine EUTPower Densit y (S)MPE Limit Powe rat 20 cm 0.001 evaluation. T86212 Satarii.xlsMPE CalcPage 2 of 2

EMC Test Report Application for Grant of Equipment Authorization Industry Canada RSS-Gen Issue 3 / RSS 210 Issue 8 FCC Part 15 Subpart C Model: SW1721(BA1) IC CERTIFICATION #: 10134A-1721BA1 FCC ID: AMX-1721BA1 APPLICANT: Satarii Inc. 1721 Notre Dame Ave. Belmont, CA 94002 TEST SITE(S): Elliott Laboratories 41039 Boyce Road. Fremont, CA. 94538-2435 IC SITE REGISTRATION #: 2845B-3; 2845B-4, 2845B-5, 2845B-7 REPORT DATE: February 13, 2012 REISSUE DATE: February 17, 2012 FINAL TEST DATES: January 31 and February 1, 2012 TOTAL NUMBER OF PAGES: 43 PROGRAM MGR / QUALITY ASSURANCE DELEGATE / TECHNICAL REVIEWER: FINAL REPORT PREPARER: ______________________________ ______________________________ Mark E Hill David Guidotti Staff Engineer Senior Technical Writer Elliott Laboratories is accredited by the A2LA, certificate number 0214.26, to perform the test(s) listed in this report, except where noted otherwise. This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full File: R86403 Rev 1 Page 1 Elliott Laboratories -- EMC Department Test Report Report Date: February 13, 2012 Reissue Date: February 17, 2012 File: R86403 Rev 1 Page 2 REVISION HISTORY Rev# Date Comments Modified By - 2-13-2012 First release 1 2-17-2012 Reissued to add in Conducted Emissions test data Dave Guidotti Elliott Laboratories -- EMC Department Test Report Report Date: February 13, 2012 Reissue Date: February 17, 2012 File: R86403 Rev 1 Page 3 TABLE OF CONTENTS REVISION HISTORY ................................................................................................................................................ 2 TABLE OF CONTENTS ............................................................................................................................................ 3 SCOPE .......................................................................................................................................................................... 4 OBJECTIVE ................................................................................................................................................................ 4 STATEMENT OF COMPLIANCE ........................................................................................................................... 5 DEVIATIONS FROM THE STANDARDS .............................................................................................................. 5 TEST RESULTS SUMMARY ................................................................................................................................... 6 DIGITAL TRANSMISSION SYSTEMS (2400 – 2483.5MHZ) .............................................................................. 6 GENERAL REQUIREMENTS APPLICABLE TO ALL BANDS .......................................................................... 6 MEASUREMENT UNCERTAINTIES .................................................................................................................... 7 EQUIPMENT UNDER TEST (EUT) DETAILS ...................................................................................................... 8 GENERAL ................................................................................................................................................................ 8 OTHER EUT DETAILS ........................................................................................................................................... 8 ANTENNA SYSTEM .............................................................................................................................................. 8 ENCLOSURE ........................................................................................................................................................... 9 MODIFICATIONS ................................................................................................................................................... 9 SUPPORT EQUIPMENT ......................................................................................................................................... 9 EUT INTERFACE PORTS ...................................................................................................................................... 9 EUT OPERATION ................................................................................................................................................... 9 TEST SITE ................................................................................................................................................................. 10 GENERAL INFORMATION ................................................................................................................................. 10 CONDUCTED EMISSIONS CONSIDERATIONS .............................................................................................. 10 RADIATED EMISSIONS CONSIDERATIONS .................................................................................................. 10 MEASUREMENT INSTRUMENTATION ............................................................................................................ 11 RECEIVER SYSTEM .............................................................................................................................…

Text truncated - open the document above for the full version.