APYBSC0004Electronic paper display

EP-C251 EP-C131 ELECTRONIC PAPER DISPLAY AFFICHAGE PAPIER ÉLECTRONIQUE PANTALLA DE PAPEL ELECTRÓNICO ELEKTRONISCHES-PAPIER-DISPLAY OPERATION MANUAL MODE D'EMPLOI MANUAL DE INSTRUCCIONES BEDIENUNGSANLEITUNG ENGLISH ...... E1 FRANÇAIS ..... F1 ESPAÑOL .... S1 DEUTSCH ..... D1 ENGLISH FRANÇAIS ESPAÑOL ENGLISH FRANÇAIS ESPAÑOL DEUTSCH FOR CUSTOMERS IN U.K. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: • The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth or coloured green or green-and-yellow. • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. • The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician. “WARNING: THIS APPARATUS MUST BE EARTHED.” IMPORTANT: To aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product. Model No.: Serial No.: U.S.A. ONLY Supplier’s Declaration of Conformity SHARP ELECTRONIC PAPER DISPLAY, EP-C131/EP-C251 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: SHARP ELECTRONICS CORPORATION 100 Paragon Drive, Montvale, NJ 07645 TEL: 1-800-BE-SHARP www.sharpusa.com U.S.A. ONLY This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines as this equipment has very low levels of RF energy. But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person's body. U.S.A. ONLY This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy. But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person's body. For indoor use only. CANADA ONLY L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’ISDE puisque cet appareil a une niveau tres bas d'energie RF. Cependant, il est souhaitable qu'il devrait être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. Pour usage intérieur seulement. CANADA SEULEMENT ENGLISH 1 E WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within a triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT INFORMATION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Thank you for your purchase of a SHARP product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. DEAR SHARP CUSTOMER To maintain compliance with EMC regulations, use shielded USB cable. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if no…

Text truncated - open the document above for the full version.

SHARP CORPORATION * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 11/22/2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: APYBSC0004；APYBSC0005 Per section 2.911(d)(7) of the FCC rules, Sharp Corporation (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Sharp Electronics Corporation Physical U.S. Company Address: 100 Paragon Dr., Montvale, NJ 07645 Agent name: Steve Petruska Agent Email Address: [email protected] FRN: 0003737772 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Designated Agent Signed: (Required, if different to Applicant): Signed: Signed: Printed name: Taihei Ohtsuka Printed name: Steve Petruska Title: Deputy Division Manager of ESG and Quality promotion unit Title: Senior Product Safety Engineer Company Name: Sharp Corporation Company Name: Sharp Electronics Corporation Date: November 22, 2023 Date: November 24, 2023 FRN Code: 0005810866 FRN Code: 0003737772

SHARP CORPORATION Covered Equipment CertificationAttestation Letter 11/22/2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: APYBSC0004 ；APYBSC0005 Sharp Corporation certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note:If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. SHARP Corporation certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Taihei Ohtsuka Title: Deputy Division Manager of ESG and Quality promotion unit Company Name: Sharp Corporation Date: 11/22/2023

SHARP CORPORATION 11/24/2023 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 AUTHORITY TO ACT AS AGENT - FCC On our behalf, I appoint Mr.Sunny Lu, from Audix Technology (Shenzhen) Co., Ltd. No. 6, Kefeng Road, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko North America Inc., still resides still resides with us. Sincerely, Printed name: Taihei Ohtsuka

SHARP CORPORATION 11/24/2023 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: APYBSC0004；APYBSC0005 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules and FCC Guidance document 726920, we hereby request confidential treatment of information accompanying this application as outlined below: PERMANENT LONG-TERM CONFIDENTIALITY: Schematics Block Diagrams Theory of Operation SHORT TERM CONFIDENTIALITY FOR A PERIOD OF 180 DAYS InternalPhotos ExternalPhotos User Manual Test Set-up Photographs When the device is marketed before the requestednumber of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed : Printed name: Taihei Ohtsuka Title: Deputy Division Manager of ESG and Quality promotion unit

AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page D1 of D4 Appendix B. Photographs of EUT Figure 1 General Appearance of the EUT Figure 2 General Appearance of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 2 of 4 Figure 3 General Appearance of the EUT Figure 4 General Appearance of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 3 of 4 Figure 5 General Appearance of the EUT Figure 6 General Appearance of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 4 of 4 Figure 7 Power Adapter Figure 8 Power Adapter THE END

Size : 100×50 mm Text : Black Base : White EP-C131 (A3EPC131U_US) Rating Label 3.0A Max 12/15V SER.No : XXXXXXXXXXX EP-C131 ELECTRONIC PAPER DISPLAY AFFICHAGE PAPIER ÉLECTRONIQUE PANTALLA DE PAPEL ELECTRÓNICO FCC ID: APYBSC0004 IC: 548B-EPC131 year.month

AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page D1 of D7 Appendix C. Photographs of EUT Figure 1 Inside Configuration of the EUT Figure 2 Inside Configuration of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 2 of 7 Figure 3 Inside Configuration of the EUT Figure 4 Inside Configuration of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 3 of 7 Figure 5 Inside Configuration of the EUT Figure 6 Inside Configuration of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 4 of 7 Figure 7 Inside Configuration of the EUT Figure 8 Inside Configuration of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 5 of 7 Figure 9 Inside Configuration of the EUT Figure 10 Inside Configuration of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 6 of 7 Figure 11 Inside Configuration of the EUT Figure 12 Inside Configuration of the EUT AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd. Page 7 of 7 Figure 13 Inside Configuration of the EUT Figure 14 Inside Configuration of the EUT THE END

Audix Technology (Shenzhen) Co., Ltd. Tel: 0755 26639496 No. 6, Kefeng Road, Science & Technology Park, Fax: 0755 26632877 Nanshan District , Shenzhen, Guangdong, China Maximum Permissive Exposure FCC ID: APYBSC0004 Product Name: Electronic paper display M/N: EP-C131 1. According to FCC CFR 47 §1.1310, the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b). Table 1 Limits for Maximum Permissible Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational / Control Exposures (f = frequency) 30-300 61.4 0.163 1.0 6 300-1500 --- --- f/300 6 1500-100,000 --- --- 5.0 6 (B) Limits for General Population / Uncontrolled Exposures (f = frequency) 30-300 27.5 0.073 0.2 30 300-1500 --- --- f/1500 30 1500-100,000 --- --- 1.0 30 2. MPE Calculation We, declares that the product described above has been evaluated and found to comply with the RF exposure limits for humans, as specified based on ANSI/FCC recommendation. RF Exposure Calculations: S = (P * G) / (4* π * r^2) or r = √(P * G) / (4 * π * S) Audix Technology (Shenzhen) Co., Ltd. Tel: 0755 26639496 No. 6, Kefeng Road, Science & Technology Park, Fax: 0755 26632877 Nanshan District , Shenzhen, Guangdong, China 2.1. Estimation Result WIFI 2.4G Test Mode Output Power (dBm) Output Power (mW) Antenna Gain (dBi) Antenna Gain (Linear) MPE 11b 14.51 28.25 2.51 1.78 0.0100 11g 14.52 28.31 2.51 1.78 0.0100 11n HT20 15.06 32.06 2.51 1.78 0.0114 Conclusion: Pass WIFI 5G Test Mode Output Power (dBm) Output Power (mW) Antenna Gain (dBi) Antenna Gain (Linear) MPE WIFI5G Band1 11a (SISO) 12.21 16.63 2.33 1.71 0.0057 11n HT20 (SISO) 11.79 15.10 2.33 1.71 0.0051 11n HT40 (SISO) 11.17 13.09 2.33 1.71 0.0045 11ac VHT20 (SISO) 11.69 14.76 2.33 1.71 0.0050 11ac VHT40 (SISO) 11.17 13.09 2.33 1.71 0.0045 11ac VHT80 (SISO) 9.85 9.66 2.33 1.71 0.0033 WIFI5G Band2A 11a (SISO) 12.50 17.78 2.33 1.71 0.0061 11n HT20 (SISO) 12.09 16.18 2.33 1.71 0.0055 11n HT40 (SISO) 10.88 12.25 2.33 1.71 0.0042 11ac VHT20 (SISO) 12.00 15.85 2.33 1.71 0.0054 11ac VHT40 (SISO) 10.91 12.33 2.33 1.71 0.0042 Audix Technology (Shenzhen) Co., Ltd. Tel: 0755 26639496 No. 6, Kefeng Road, Science & Technology Park, Fax: 0755 26632877 Nanshan District , Shenzhen, Guangdong, China 11ac VHT80 (SISO) 10.39 10.94 S2.33 1.71 0.0037 WIFI5G Band2C 11a (SISO) 11.86 15.35 2.33 1.71 0.0052 11n HT20 (SISO) 11.30 13.49 2.33 1.71 0.0046 11n HT40 (SISO) 10.36 10.86 2.33 1.71 0.0037 11ac VHT20 (SISO) 11.30 13.49 2.33 1.71 0.0046 11ac VHT40 (SISO) 10.36 10.86 2.33 1.71 0.0037 11ac VHT80 (SISO) 9.56 9.04 2.33 1.71 0.0031 WIFI5G Band3 11a (SISO) 8.90 7.76 1.91 1.55 0.0024 11n HT20 (SISO) 8.39 6.90 1.91 1.55 0.0021 11n HT40 (SISO) 7.37 5.46 1.91 1.55 0.0017 11ac VHT20 (SISO) 8.42 6.95 1.91 1.55 0.0021 11ac VHT40 (SISO) 7.54 5.68 1.91 1.55 0.0018 11ac VHT80 (SISO) 6.55 4.52 1.91 1.55 0.0014 Conclusion: Pass Audix Technology (Shenzhen) Co., Ltd. Tel: 0755 26639496 No. 6, Kefeng Road, Science & Technology Park, Fax: 0755 26632877 Nanshan District , Shenzhen, Guangdong, China The antenna gain (G) numerical as below: Based on safety distance (r) 20cm, and the WiFi 2.4GHz highest power output (P) is 32.06mW, and the WiFi 5GHz highest power output (P) is 17.78mW; the WiFi 2.4GHz power density (S) is 0.0114 mW/cm 2 , the WiFi 5GHz power density (S) is 0.0061 mW/cm 2 ,hence the EUT is excluded from SAR evaluation Note: The EUT is equipped with more than one transmitting antennas,the antennas can not be transmit simultaneously.

AUDIX Technology (Shenzhen) Co., Ltd. FCC ID: APYBSC0004 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F23202 Page 1 of 76 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of SHARP Corporation Electronic paper display EP-C131 FCC ID: APYBSC0004 SHARP Prepared for : SHARP Corporation 1 Takumi-cho, Sakai-ku Sakai City Osaka 590-8522 Japan Prepared By : Audix Technology (Shenzhen) Co., Ltd. No. 6, Kefeng Road, Science & Technology Park, Nanshan District , Shenzhen, Guangdong, China Tel: (0755) 26639496 Report Number ： ACS-F23202 Date of Test ： Oct.17~Nov.13, 2023 Date of Report ： Nov.28, 2023 TESTING NVLAP LAB CODE 200372-0 AUDIX Technology (Shenzhen) Co., Ltd. FCC ID: APYBSC0004 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F23202 Page 2 of 76 TABLE OF CONTENTS Description Page 1. SUMMARY OF STANDARDS AND RESULTS ............................................................. 5 1.1. Description of Standards and Results ..................................................................................... 5 2. GENERAL INFORMATION ............................................................................................. 6 2.1. Description of Equipment Under Test .................................................................................... 6 2.2. Feature of Equipment Under Test ........................................................................................... 7 2.3. Tested Supporting System Details .......................................................................................... 8 2.4. Block Diagram of connection between EUT and simulators .................................................. 8 2.5. Test information ...................................................................................................................... 8 2.6. Test Facility ............................................................................................................................ 9 2.7. Measurement Uncertainty (95% confidence levels, k=2) ....................................................... 9 3. POWER LINE CONDUCTED EMISSION TEST ........................................................ 10 3.1. Test Equipments .................................................................................................................... 10 3.2. Block Diagram of Test Setup ................................................................................................ 10 3.3. Power Line Conducted Emission Test Limits ...................................................................... 10 3.4. Configuration of EUT on Test .............................................................................................. 10 3.5. Operating Condition of EUT ................................................................................................ 11 3.6. Test Procedure ...................................................................................................................... 11 3.7. Power Line Conducted Emission Test Results ..................................................................... 11 4. RADIATED EMISSION MEASUREMENT .................................................................. 14 4.1. Test Equipments .................................................................................................................... 14 4.2. Block Diagram of Test Setup ................................................................................................ 15 4.3. Radiated Emission Limits Standard: ..................................................................................... 16 4.4. EUT Configuration on Test .................................................................................................. 16 4.5. Operating Condition of EUT ................................................................................................ 16 4.6. Test Procedure ...................................................................................................................... 17 4.7. Radiated Emission Test Results ............................................................................................ 17 5. CONDUCTED SPURIOUS EMISSIONS ....................................................................... 45 5.1. Test Equipments .................................................................................................................... 45 5.2. Block Diagram of Test Setup ................................................................................................ 45 5.3. Limit ...................................................................................................................................... 45 5.4. Test Procedure ...................................................................................................................... 45 5.5. Test result .............................................................................................................................. 45 6. 6DB & 99% BANDWIDTH TEST ................................................................................... 52 6.1. Test Equipments .................................................................................................................... 52 6.2. Block Diagram of Test Setup ................................................................................................ 52 6.3. Limit ...................................................................................................................................... 52 6.4. Test Procedure ...................................................................................................................... 52 6.5. Test Results ........................................................................................................................... 53 7. MAXIMUM PEAK OUTPUT POWER TEST ............................................................... 58 7.1. Test Equipments ...........................................................................................................…

Text truncated - open the document above for the full version.

AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:APYBSC0004 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F23203 Page 1 of 123 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of SHARP Corporation Electronic paper display Model No.: EP-C131 FCC ID: APYBSC0004 SHARP Prepared for : SHARP Corporation 1 Takumi-cho, Sakai-ku Sakai City Osaka 590-8522 Japan Prepared By : Audix Technology (Shenzhen) Co., Ltd. No. 6, Kefeng Road, Science & Technology Park, Nanshan District , Shenzhen, Guangdong, China Tel: (0755) 26639496 Report Number ： ACS-F23203 Date of Test ： Oct.17~Nov.07, 2023 Date of Report ： Nov.28, 2023 TESTING NVLAP LAB CODE 200372-0 AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:APYBSC0004 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F23203 Page 2 of 123 TABLE OF CONTENTS Description Page 1. SUMMARY OF STANDARDS AND RESULTS ............................................................. 5 1.1. Description of Standards and Results ..................................................................................... 5 2. GENERAL INFORMATION............................................................................................. 6 2.1. Description of Equipment Under Test .................................................................................... 6 2.2. Feature of Equipment Under Test ........................................................................................... 7 2.3. Tested Supporting System Details .......................................................................................... 8 2.4. Block diagram of connection between the EUT and simulators ............................................. 8 2.5. Test Information ...................................................................................................................... 8 2.6. Test Facility ............................................................................................................................ 9 2.7. Measurement Uncertainty (95% confidence levels, k=2) ....................................................... 9 3. POWER LINE CONDUCTED EMISSION TEST ........................................................ 10 3.1. Test Equipments .................................................................................................................... 10 3.2. Block Diagram of Test Setup ................................................................................................ 10 3.3. Power Line Conducted Emission Test Limits....................................................................... 10 3.4. Configuration of EUT on Test .............................................................................................. 10 3.5. Operating Condition of EUT................................................................................................. 11 3.6. Test Procedure ...................................................................................................................... 11 3.7. Power Line Conducted Emission Test Results ..................................................................... 11 4. RADIATED EMISSION TEST ....................................................................................... 14 4.1. Test Equipments .................................................................................................................... 14 4.2. Block Diagram of Test Setup ................................................................................................ 15 4.3. Radiated Emission Limits ..................................................................................................... 16 4.4. EUT Configuration on Test .................................................................................................. 16 4.5. Operating Condition of EUT................................................................................................. 17 4.6. Test Procedure ...................................................................................................................... 17 4.7. Radiated Emission Test Results ............................................................................................ 17 5. CONDUCTED SPURIOUS EMISSIONS ....................................................................... 75 5.1. Test Equipments .................................................................................................................... 75 5.2. Limit ...................................................................................................................................... 75 5.3. Test Procedure ...................................................................................................................... 75 5.4. Test result .............................................................................................................................. 75 6. BAND EDGE COMPLIANCE TEST ............................................................................. 83 6.1. Test Equipments .................................................................................................................... 83 6.2. Limit ...................................................................................................................................... 83 6.3. Test Procedure ....................................................................................................................... 83 6.4. Test Results ........................................................................................................................... 83 7. 6dB Bandwidth & 99% Bandwidth TEST ................................................................... 108 7.1. Test Equipments .................................................................................................................. 108 7.2. Limit .................................................................................................................................... 108 7.3. Test Procedure ....................................................…

Text truncated - open the document above for the full version.

AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:APYBSC0004 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F23203 Page 82 of 123 Test CH11: 2462MHz AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:APYBSC0004 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F23203 Page 83 of 123 6. BAND EDGE COMPLIANCE TEST 6.1. Test Equipments Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. 3mChamber(Svswr) AUDIX N/A N/A Aug.09,22 3Year 2. 3mChamber(SE) AUDIX N/A N/A Sep.16,22 3Year 3. Signal Analyzer Rohde & Schwarz FSV30 104050 Apr.01,23 1 Year 4. Amplifier EMCI EMC0518A45SE 980965 Aug.25,23 1 Year 5. RF Cable Shanghaichaoyu SFT205-NMSM- 10.00M 689241 Aug.25,23 1 Year 6. Test Software AUDIX e3 6.100913a N/A N/A 7. Horn Antenna ETC MCTD 1209 DRH1…

Text truncated - open the document above for the full version.