APYDMR0182Smart convection wall oven with microwave drawer oven.

MANUA C OOK SMART COOK MEAT PROBE MICROWAVEOVEN CLOSEOPEN HOME 09:01 AM Thu Oct 24 SMART COOK L Sharp Smart Convection Wall Oven With Microwave Drawer ™ Oven : Model SWB3085HS OPERATION MANUAL SHARP SMART CONVECTION WALL OVEN WITH MICROWAVE DRAWER ™ OVEN MODEL SWB3085HS PRELIMINARY May 31, 2023 @ 2 PM TINSKB322MRR0 May 31, 2023 @ 2 PM IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference. 2 CONTENTS PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not attempt to operate this oven with the door open since open-door operation can result in harmful exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks. (b) Do not place any object between the oven front face and the door or allow soil or cleaner residue to accumulate on sealing surfaces. (c) Do not operate the oven if it is damaged. It is particularly important that the oven door close properly and that there is no damage to the: (1) door (bent), (2) hinges and latches (broken or loosened), (3) door seals and sealing surfaces. (d) The oven should not be adjusted or repaired by anyone except properly qualified service personnel. PRECAUTIONS TO AVOID POSSIBLE EXPOSURE ................2 CUSTOMER ASSISTANCE ............................................3 US CONSUMER LIMITED WARRANTY .............................4 OVEN SAFETY .........................................................5 IMPORTANT SAFETY INSTRUCTIONS ............................6-8 IMPORTANT INFORMATION ........................................9 UNPaCK THE aPPLIaNCE .......................................................9 BEFORE OPERaTING ...............................................................9 CONDITION OF UNIT ...............................................................9 SERVICE aND REPaIR WaRNING ...........................................9 RaDIO OR TV INTERFERENCE ................................................9 GROUNDING INSTRUCTIONS .................................................9 PRODUCT DISPOSaL ..............................................................9 PARTS AND FEATURES..........................................10-11 TOUCH SCREEN CONTROL .....................................12-14 HOME ...................................................................................13 UPPER OVEN .......................................................................13 LOWER MICROWaVE OVEN .................................................14 SETTINGS ............................................................................14 OVEN USE .........................................................15-16 BEFORE USING THE OVEN ...................................................15 GENERaL ..............................................................................15 MICROWAVE DRAWER USE ....................................17-19 GENERaL ..............................................................................17 POWER LEVEL ......................................................................17 MICROWaVE COOKING ........................................................17 MICROWaVE SaFETy ...........................................................18 MICROWaVE UTENSILS .......................................................18 FOOD IN THE MICROWaVE ...................................................19 CLEANING AND CARE ...........................................20-23 OVEN GENERaL CLEaNING ..................................................20 aUTOMaTIC SELF-CLEaNING ...............................................21 OVEN DOOR REMOVaL ........................................................21 REPLaCING aN OVEN LIGHT ................................................22 MICROWaVE OVEN CaRE ....................................................23 TROUBLESHOOTING .............................................24-25 CUSTOMER ASSISTANCE UNITED STATES ONLY REGISTER YOUR PRODUCT Registering your new product is easy and offers benefits that help you get the most out of your Sharp product including: 9Convenience: If you ever need warranty support, your product information is already on file. 9Communication: Stay up to date with important notifications and special offers from SHARP. 9Support: Quickly access support content including Owner’s Manuals, FAQ’s, How-to Videos, and much more. 3 EASY WAYS TO REGISTER TODAY! PRODUCT SUPPORT If you have questions about the setup or operation of your product, please refer to the corresponding section within this manual. Additionally, visit www.sharpusa.com/support to access exclusive content about your product including: ÆFAQ’s and How-To Videos ÆFind or Request Service ÆExtended Warranty Options ÆDownloads including the Installation Guide, Spec Sheet, and Owner’s Manual CONTACT US If at any time you have questions or comments concerning your SHARP product, please contact the SHARP Customer Assistance Center. We are available to assist you through multiple contact methods for your convenience: Scan this QR Code on your mobile deviceVisit http://www.sharpusa.com/register ONLINE Visit our sites to learn more about your product at sharpusa.com and sbl.sharpusa.com See the Contact Us section on our sitesU.S. | www.sharpusa.com/supportContact a Sharp Advisor on the phone Contact a Sharp Advisor on the phone CALL US US 800-BE-SHARP 800-237-4277 Mon-Fri: 7am-7pm CST Sat-Sun: 9am-7pm CST CALL US US 800-BE-SHARP 800-237-4277 Mon-Fri: 7am-7pm CST Sat-Sun: 9am-7pm CST EMAIL Available 24/7 US: sharpusa.com CHAT ONLINE Mon-Fri: 7am-7pm CST Sat-Sun: 9am-7pm CST SCAN Use the camera or QR code scanning application on your mobile device 3 CUSTOMER ASSISTANCE US CONSUMER LIMITED WARRANTY E5 E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E SHARP ELECTRONICS CORPORATION (“Sharp”) warrants to the first consumer purchaser (“Purchaserˮ) that this SHARP brand product (“Productˮ)…

Text truncated - open the document above for the full version.

US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 1 of 1 MPE Separation Distance Statement Will be added into the User’s Manual

1 Takumi-cho, Sakai-ku, Sakai City, Osaka 590-8522, Japan Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 06-20-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: APYDMR0182 SHARP CORPORATION (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, _________________________ (Signature) SHARP CORPORATION Taihei Ohtsuka [email protected] 1 Takumi-cho, Sakai-ku, Sakai City, Osaka 590-8522, Japan Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 06-20-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: APYDMR0182 SHARP CORPORATION (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, _________________________ (Signature) SHARP CORPORATION Taihei Ohtsuka [email protected]

1 Takumi-cho, Sakai-ku, Sakai City, Osaka 590-8522, Japan Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 06-20-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID or Grantee Code: APYDMR0182 SHARP CORPORATION (“the applicant”) certifies that, as of the date of the filing of the application, Sharp Electronics Corporation is our designated U.S. agent for service of process for the above referenced FCC ID. Taihei Ohtsuka accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Sharp Electronics Corporation accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Sharp Electronics Corporation FRN: 0003737772 Address: 100 Paragon Dr., Montvale, NJ 07645 Contact Person: Steve Petruska Email: [email protected] Sincerely, Sharp Corporation Sharp Electronics Corporation Taihei Ohtsuka Steve Petruska

1 Takumi-cho, Sakai-ku, Sakai City, Osaka 590- 8522, Japan Tel : 81-50-5433-4157 AGENCY AGREEMENT Federal Communications Commission P.O. Box 429 Columbia, MD 21045 Gentleman: By signature below, we hereby appoint Us Tech Employees Alan Ghasiani and George Yang to act as our agents with regards to the FCC equipment authorizations relating to the following FCC ID(*). This appointment will remain in effect until otherwise notified. I further certify by signature below that no party (per 47 CFR 1.2002(b) to the application is subject to a denial of Federal benefits, including GCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment includes authority to complete FCC Form 731 on their behalf and sign the application as an authorized agent. *FCC ID: APYDMR0182 Name: Taihei Ohtsuka Signature: ___________________________ Title: Deputy Division Manager SHARP CORPORATION Date: ______________________________ 29th May, 2023

Request for Confidentiality Date: ___May 24, 2023____ Subject: Confidentiality Request for: ___FCC ID: APYDMR0182 Pursuant to FCC 47 CRF 0.457(d) and 0.459, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual Sharp Manufacturing Company of America has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent (Long Term) Confidentiality: The applicant requests the exhibits identified above be permanently withheld from public review/access due to materials that contain trade secrets and proprietary information not customarily released to the public. Sincerely, By: __________________________ ___George Yang __- Agent (Signature/Title) (Print name)

US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 1 of 6 External Photographs Figure 1. EUT Front Note: Microwave Drawer denoted above. US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 2 of 6 Figure 2. EUT Right Side US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 3 of 6 Figure 3. EUT Back US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 4 of 6 Figure 4. EUT Left Side US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 5 of 6 Figure 5. EUT Top Side US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 6 of 6 Figure 6. EUT Bottom Side

US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 1 of 2 SAMPLE LABEL Figure 1. Sample Label US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 2 of 2 Figure 2. Label Location Label will go on this surface

US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 1 of 14 Internal Photos: The microwave drawer was separated from the convection oven for these photographs. Figure 1. Magnetron in EUT US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 2 of 14 Figure 2. Close-up of Magnetron Label in situ \ US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 3 of 14 Figure 3. Rear View Magnetron US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 4 of 14 Figure 4. Left Side US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 5 of 14 Figure 5. Right Side US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 6 of 14 Figure 6. Top Side US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 7 of 14 Figure 7. Rear Display Panel top of Convection Oven US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 8 of 14 Figure 8. Electrical section of the top of Convection Oven US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 9 of 14 Figure 9. Front of Display PCBA US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 10 of 14 Figure 10. Back of Display PCBA US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 11 of 14 Figure 11. Wi-Fi radio module and host interface board #1 US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 12 of 14 Figure 12. Wi-Fi radio module and host interface board #2 US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 13 of 14 Figure 13. Wi-Fi modules on host interface boards, Top View US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 14 of 14 Figure 14. Wi-Fi modules on host interface boards, Bottom View

Magnetron Technical Information: Toshiba, 2M303H (L)

US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 1 of 3 Maximum Permissible Exposure to RF (MPE), CFR 1.1310 (e) And Total Sum of MPE Calculation The maximum exposure level to the public from the RF power of the EUT shall not exceed a power density, S as per the respective limits in Table 1 below, at a distance, d, of 20 cm (Mobile condition) from the EUT. TABLE 1—LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *100 30 1.34-30 824/f 2.19/f *180/f 2 30 30-300 27.5 0.073 0.2 30 300-1,500 f/1500 30 1,500-100,000 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density Therefore, for: MPE for 2404 MHz – 2480 MHz for BLE: Limit: 1.0 mW/cm 2 Peak Power (dBm) = 7.5 dBm Gain of Transmit Antenna = +2.64 dB i d = Distance = 20 cm = 0.2 m S = (PG/ 4π ππ πd 2 ) = = 0.002 mW/cm 2 which is << less than S = 1.0 mW/cm 2 See attached RF Exposure Report # SZ23050028S01 for details. US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 2 of 3 MPE for 2412 MHz – 2462 MHz for WiFi: Limit: 1.0 mW/cm 2 Peak Power (dBm) = 16.5 dBm Gain of Transmit Antenna = +2.64 dB i d = Distance = 20 cm = 0.2 m S = (PG/ 4π ππ πd 2 ) = = 0.016 mW/cm 2 which is << less than S = 1.0 mW/cm 2 See attached RF Exposure Report # SZ23050028S01 for details. MPE for 2400 MHz – 2500 MHz for Microwave Oven: Limit: 1.0 mW/cm 2 Signal Strength (V/m) = 3.8 V/m Power Flux Density (PFD) = V/m 2 /377 = W/m 2 = 8.14 2 /377 = 0.0271 W/m 2 = (0.0271 W/m 2 ) (1m 2 /W) (0.1 mW/cm 2 ) = 0.00271 mW/cm 2 which is << less than S = 1.0 mW/cm 2 See attached US Tech report # 23-0051 for details. US Tech Test Report: FCC Part 18 Subpart C FCC ID: APYDMR0182 Test Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation Model: SWB3085HS Page 3 of 3 Simultaneous Transmission Collocation considerations: Please either confirm that the transmitters operate standalone per KDB 447498 D01 v06 section 7.1 or, if the transmitters can transmit simultaneously, include the necessary calculations for simultaneous transmission per KDB 447498 D01 v06 section 7.2. The Transmitters do simultaneously broadcast at the same frequency band, 2400- 2483.5 MHz. The device has three radios on board, however two of the radios are Wi-Fi or BLE combo radio and not both can transmit at the same time. The radios that operate at the same time is either one Wi-Fi/BLE radio and Microwave Oven or the other Wi-Fi/BLE and Microwave Oven. The Wi-Fi and BLE radio share a common antenna. The microwave oven has it’s own transmit antenna. Calculations for simultaneous transmission per KDB 447498 D01 v06 section 7.2 is provided here to show that Simultaneous transmission MPE test exclusion applies since the sum of the MPE ratios for all simultaneously transmitting antennas incorporated in a host device is ≤ 1.0. Total Sum of MPE: Sum of the total MPE for Wi-Fi + BLE + Microwave Oven = 0.016 mW/cm 2 + 0.002 mW/cm 2 + 0.00271 mW/cm 2 = 0.0207 which is << less than 1.0 The EUT was tested with all radios ON and active. The emissions generated with a single radio ON and active versus all radios ON and active did not produce additional unwanted spurious emissions or intermodulation that would require additional testing. The radios can be collocated as designed.

NOTE: This document is issued by Shenzhen Morlab Communications Technology Co., Ltd., the test report shall not be reproduced except in full without prior written permission of the company. The test results apply only to the particular sample(s) tested and to the specific tests carried out which is available on request for validation and information confirmed at our website. MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] Page 1 of 8 REPORT No.：SZ23050028S01 RF EXPOSURE EVALUATION REPORT APPLICANT : Linkplay Technology Inc. PRODUCT NAME : IoT Module MODEL NAME : S21 BRAND NAME :Linkplay FCC ID : 2BABF-S21 STANDARD(S) : 47 CFR Part 2(2.1091) RECEIPT DATE : 2023-05-06 TEST DATE :2023-05-09 to 2023-05-25 ISSUE DATE : 2023-06-12 Edited by: Zeng Xiaoying (Rapporteur) Approved by: Shen Junsheng (Supervisor) MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23050028S01 Page 2of 8 DIRECTORY 1. Technical Information ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3 1.1 Applicant and Manufacturer Information ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3 1.2 Equipment under Test (EUT) Description ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3 1.3 Applied Reference Documents ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 4 2. Device Category and RF Exposure Limit ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 5 3. RF Output Power ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 6 4. RF Exposure Assessment ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 7 Annex A Testing Laboratory Information ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 8 Change History Version Date Reason for change 1.0 2023-06-12 First edition MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23050028S01 Page 3of 8 1. Technical Information Note: Provide by applicant. 1.1 Applicant and Manufacturer Information Applicant: Linkplay Technology Inc. Applicant Address: 8000 Jarvis Avenue Suite #130, Newark, CA 94560 Manufacturer: Linkplay Technology Inc. Manufacturer Address: 8F-8036, Qianren Building, No.7, Yingcui Road, Jiangning District, Nanjing, China 1.2 Equipment under Test (EUT) Description Product Name: IoT Module Sample No.: 1# Hardware Version: V02 Software Version: v4.2-beta1-328-g97688dc2-dirty Modulation Technology: Bluetooth GFSK WLAN 2.4GHz DSSS, OFDM Operating Frequency Range: Bluetooth 2402MHz-2480MHz WLAN 2.4GHz 2412MHz-2462MHz Antenna Type: PCB Antenna Antenna Gain: 2.64dBi MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23050028S01 Page 4of 8 1.3 Applied Reference Documents Leading reference documents for testing: Identity Document Title Method determination /Remark 47 CFR Part 2(2.1091) Radio Frequency Radiation Exposure Assessment: mobile devices No deviation KDB 447498 D01v06 General RF Exposure Guidance No deviation Note 1: Additions to, deviation, or exclusions from the method shall be judged in the "method determination" column of add, deviate or exclude from the specific method shall be explained in the "Remark" of the above table. Note 2: When the test result is a critical value, we will use the measurement uncertainty give the judgment result based on the 95% confidence intervals. MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23050028S01 Page 5of 8 2. Device Category and RF Exposure Limit Per user manual, based on 47 CFR 2.1091, this device belongs to mobile device category with General Population/Uncontrolled exposure. Mobile Devices: 47 CFR 2.1091(b) For purposes of this section, a mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. In this context, the term “fixed location” means that the device is physically secured at one location and is not able to be easily moved to another location. Transmitting devices designed to be used by consumers or workers that can be easily re-located, such as wireless devices associated with a personal computer, are considered to be mobile devices if they meet the 20 centimeter separation requirement. General Population/Uncontrolled Exposure: The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their…

Text truncated - open the document above for the full version.

Page 1 of 34 CFR 47 Part 18 Industrial Scientific and Medical Equipment Subpart C Technical Standards, Part 18.305, Field Strength Limits and Part 18.307, Conducted limits Certification Report for the Sharp Corporation Microwave Oven Drawer Wall Oven Combo with IoT Model: SWB3085HS FCC ID: APYDMR0182 Test Dates: Issue Date: May 24, 2023 Total Number of Pages Contained Within this report: 34 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com Page 2 of 34 I certify that I am authorized to sign for the manufacturer and that all of the statements in this report and in the exhibits attached hereto are true and correct to the best of my knowledge and belief: US Tech (Agent responsible for test): By: _________________ Name: Alan Ghasiani Title: President – Consulting Engineer Date: May 24, 2023 This report shall not be reproduced except in full. This report may be copied in part only with the prior written approval of US Tech. The results contained in this report are subject to the adequacy and representative character of the sample provided. US Tech NVLAP accreditation does not allow product endorsement by NVLAP or any agency of the U.S. Government. 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com US Tech Test Report: FCC Part 18 Subpart C Report Number: 23-0051 Issue Date: May 24, 2023 Customer: Sharp Corporation FCC ID: APYDMR0182 Model: SWB3085HS Page 3 of 34 Table Of Contents Title Paragraph Page 1. General Information ......................................................................................................... 5 1.1 Purpose of the Report ............................................................................................ 5 1.2 Product Description ................................................................................................ 5 1.3 Related Submittal(s)/Grant(s)................................................................................. 5 1.4 Test Methodology ................................................................................................... 6 1.5 Test Facility ............................................................................................................ 6 1.6 Test Equipment ...................................................................................................... 7 1.7 Characterization of Sample Tested ........................................................................ 8 1.8 EUT Exercise Software .......................................................................................... 8 1.9 Special Accessories ............................................................................................... 8 1.10 Test Rationale ..................................................................................................... 8 1.11 Tested System Details ........................................................................................ 8 1.12 Configuration of Tested System .......................................................................... 9 1.13 Equipment Modifications ................................................................................... 10 1.14 Test Results ...................................................................................................... 10 1.15 Measurement Uncertainty ................................................................................. 10 2. Emissions Data, Power Line and Radiated (47 CFR 18.301, 18.303, 18.305, 18.307) . 11 2.1 Test Site Description, Power Line Emissions........................................................... 11 2.2 Power Line Emissions Test Data ............................................................................. 12 2.3 Test Site Description, Radiated Emissions .............................................................. 14 2.4 Radiated Emissions Test Data................................................................................. 16 2.4.1 Part 18 ISM Test Limits and Calculations ......................................................... 16 2.4.2 General Field Strength Calculation ................................................................... 17 2.4.3 Radiated Emissions Test Results ...................................................................... 17 3. Emissions Test Configuration Photographs .................................................................. 21 4. Variation in Operating Frequency .................................................................................. 26 4.1 Variation in Operating Frequency Over Time .…

Text truncated - open the document above for the full version.