APYHRO00145Cellular Phone

◎公共の場所で携帯電話をご利用の際は、周囲の方への心くばりを忘れずに。 ●紛失・盗難などにあわれたら、速やかに利用中断手続きをお取りください。●お客様が購入されたFOMA端末に故障が発生した場合は、ご帰国後にドコモ指定の故障取扱窓口へご持参ください。 環境保全のため、不要になった電池はNTTドコモまたは代理店、リサイクル協力店などにお持ちください。 再生紙を使用しています ユニバーサルナンバー用国際識別番号滞在国の国際電話アクセス番号 -81-3-6718-1414 ＊ （無料） -8005931-8600 ＊ ＊一般電話などでかけた場合には、日本向け通話料がかかります。 ※SH-10Cからご利用の場合は、＋81-3-6718-1414でつながります。 （「＋」は「０」ボタンを１秒以上押します。） ＊滞在国内通話料などがかかる場合があります。 ※主要国の国際電話アクセス番号／ユニバーサルナンバー用国際識 別番号については、ドコモの「国際サービスホームページ」をご覧ください。 一般電話などからの場合ドコモの携帯電話からの場合 海外での故障について ＜ネットワークオペレーションセンター＞ （24時間受付） ＜ユニバーサルナンバー＞ ＊滞在国内通話料などがかかる場合があります。 ※主要国の国際電話アクセス番号／ユニバーサルナンバー用国際識 別番号については、ドコモの「国際サービスホームページ」をご覧ください。 ＊一般電話などでかけた場合には、日本向け通話料がかかります。 ※SH-10Cからご利用の場合は、＋81-3-6832-6600でつながります。 （「＋」は「０」ボタンを１秒以上押します。） -8000120-0151 ＊ ユニバーサルナンバー用国際識別番号 -81-3-6832-6600 ＊ （無料） 滞在国の国際電話アクセス番号 海外での紛失、盗難、精算などについて ＜ドコモ インフォメーションセンター＞ （24時間受付） ドコモの携帯電話からの場合 一般電話などからの場合 ＜ユニバーサルナンバー＞ ※ 一般電話などからはご利用になれません。 （局番なしの） 113 （無料） ■ドコモの携帯電話からの場合 ※ 一般電話などからはご利用になれません。 （局番なしの） 151 （無料） ■ドコモの携帯電話からの場合 SH-10C ’11. 故障お問い合わせ先 ※一部のIP電話からは接続できない場合があります。 0120-800-000 ■一般電話などからの場合受付時間 24時間 （年中無休） 受付時間 午前9:00～午後8:00 （年中無休） ※一部のIP電話からは接続できない場合があります。 0120-800-000 ■一般電話などからの場合 総合お問い合わせ先 ＜ドコモ インフォメーションセンター＞ ●番号をよくご確認の上、お間違いのないようにおかけください。● 各種手続き、故障・アフターサービスについては、上記お問い合わせ先にご連絡いただくか、ドコモホームページ、ｉモードサイトにてお近くのドコモショップなどにお問い合わせください。 ドコモホームページ http://www.nttdocomo.co.jp/ ｉモードサイト iMenu お客様サポート ドコモショップ SH-10C 1 11* **.* ** SM*** TINSJA816AFZZ ’11. ’11. 9 j01_dv85_9j.fm [9/24] 目 次 ／ 注 意 事 項 ハンズフリーに設定して通話す る際や、着信音が鳴っていると きなどは、必ずFOMA端末を耳 から離してください。 また、イヤホンマイクなどを FOMA端末に装着し、ゲームや 音楽再生をする場合は、適度な ボリュームに調節してくださ い。 音量が大きすぎると難聴の原因となります。 また、周囲の音が聞こえにくいと、事故の原因と なります。 Earphone Signal Level The maximum output voltage for the music player function, measured in accordance with EN 50332-2, is 28.0 mV. 心臓の弱い方は、着信バイブ レータ（振動）や着信音量の設定 に注意してください。 心臓に悪影響を及ぼす原因となります。 医用電気機器などを装着してい る場合は、医用電気機器メーカ もしくは販売業者に、電波によ る影響についてご確認の上ご使 用ください。 医用電気機器などに悪影響を及ぼす原因となり ます。 高精度な制御や微弱な信号を取 り扱う電子機器の近くでは、 FOMA端末の電源を切ってくだ さい。 電子機器が誤動作するなどの悪影響を及ぼす原 因となります。 ご注意いただきたい電子機器の例 補聴器、植込み型心臓ペースメーカおよび植込み 型除細動器、その他の医用電気機器、火災報知器、 自動ドア、その他の自動制御機器など。植込み型 心臓ペースメーカおよび植込み型除細動器、その 他の医用電気機器をご使用される方は、当該の各 医用電気機器メーカもしくは販売業者に電波に よる影響についてご確認ください。 万が一、ディスプレイ部やカメ ラのレンズを破損した際には、 割れたガラスや露出したFOMA 端末の内部にご注意ください。 ディスプレイ部の表面には保護フィルム、カメラ のレンズの表面にはプラスチックパネルを使用 し、ガラスが飛散りにくい構造となっております が、誤って割れた破損部や露出部に触れますと、 けがの原因となります。 アンテナ、ストラップなどを 持ってFOMA端末を振り回さな いでください。 本人や他の人に当たり、けがなどの事故の原因と なります。 FOMA端末が破損したまま使用 しないでください。 火災、やけど、けが、感電の原因となります。 モーショントラッキングやモー ションセンサーのご使用にあ たっては、必ず周囲の安全を確 認し、FOMA端末をしっかりと 握り、必要以上に振り回さない でください。 けがなどの事故の原因となります。 誤ってディスプレイを破損し、 液晶など内部の物質が漏れた場 合には、顔や手などの皮膚につ けないでください。 失明や皮膚に傷害を起こす原因となります。 液晶など内部の物質が目や口に入った場合には、 すぐにきれいな水で洗い流し、直ちに医師の診断 を受けてください。 また、皮膚や衣類に付着した場合は、すぐにアル コールなどで拭き取り、石鹸で水洗いしてくださ い。 ディスプレイの表面には、落下 や衝撃等により破損した場合の 安全性確保（強化ガラスパネル の飛散防止）を目的とする保護 フィルムがあります。このフィ ルムは無理にはがしたり、傷つ けたりしないでください。 フィルムをはがして使用した場合、ディスプレイ が破損したときに、けがの原因となることがあり ます。 注意 dv85_j.book 9 ページ ２０１１年３月２２日 火曜日 午後３時４６分 116 ̷͈ఈ Use only the battery packs and adapters specified by NTT DOCOMO for use with the FOMA terminal. May cause fires, burns, bodily injury or electric shock. Do not throw the battery pack into a fire. The battery pack may catch fire, explode, overheat or leak. Do not dispose of used battery packs in ordinary garbage. May cause fires or damage to the environment. Place tape over the terminals to insulate unnecessary battery packs, and take them to a docomo Shop, retailer or institution that handles used batteries in your area. Avoid using the handset in extremely high or low temperatures. Use the FOMA terminal within the range of a temperature between 5°C and 40°C (for temperatures of 36°C or higher, such as in a room with a bath, limit usage to a short period of time) and a humidity between 45% and 85%. Charge battery in areas where ambient temperature is between 5°C and 35°C. Do not point the illuminated light directly at someone’s eyes. Especially when you shoot still pictures or moving pictures of young children, keep 1 m or more distance from them. Do not use Picture Light near people’s faces. Eyesight may be temporarily affected leading to accidents. CAUTION: Use of controls, adjustments or performance of procedure other than those specified herein may result in hazardous radiation exposure. As the emission level from Picture Light LED used in this product is harmful to the eyes, do not attempt to disassemble the cabinet. Servicing is limited to qualified servicing station only. Picture light source LED characteristics a) Continuous illumination b) Wavelength White: ɜɜ-ɜɜ nm Red: ɜɜ-ɜɜ nm c) Maximum output White: ɜɜ mW (inside FOMA terminal ɜɜ mW) Red: ɜɜ mW (inside FOMA terminal ɜɜ mW) Quick Manual CAUTION Picture Light EN60825-1:1994 A1:2002 & A2:2001 CLASS1 LED Product e: ɜ d: ite: ( d: (in (nalɜɜ nal 117 j07_2_dv85.fm [117/131] ~~~~~~~~~~~~~~~~~~~~~~~~~ その他 1Hook a finger on the tab and pull out the tray (1) Pull out the tray straight until it stops. 2Hold the UIM with the IC (gold) side turned up and set on the tray (2) 3Push the tray all the way in (3) Perform with the FOMA terminal turned off and closed while holding with your both hands. The battery pack is not waterproof/dust-proof. 1Slide the back cover lever in the direction of the arrow (1) to unlock and remove the back cover (2) The FOMA terminal has a slot to remove the back cover. Securely hold the FOMA terminal as shown in the illustration to prevent excessive force on the back cover and hook a nail on the slot and remove the back cover upward. 2Attach the battery pack Turn a recycle mark side of the battery pack up, match tabs and attach the battery pack. Before Using Inserting UIM Note that inserting or removing the UIM forcibly may damage the UIM or deform the tray. Notch IC (gold) Tray Ta b Notch Attaching battery pack Slot Tabs With a recycle mark side up dv85_uj.book 117 ページ ２０１１年３月２２日 火曜日 午後３時１０分 j07_2_dv85.fm [118/131] ~~~~~~~~~~~~~~~~~~~~~~~~~ 118 その他 3Insert the tab of the top of the back cover into the FOMA terminal slot (1), attach it in the direction…

Text truncated - open the document above for the full version.

Model Name:SH-10CPhoto(External)13th/April/2011 1 / 3 Model Name:SH-10CPhoto(External)13th/April/2011 2 / 3 Model Name:SH-10CPhoto(External)13th/April/2011 3 / 3

Model Name: SH-10C FCC ID: APYHRO00145 ○Spec Label Caution : Turn off power in an aircraft. Don't remove this seal. Vendor : NTT DoCoMo ① Color Name ② Approval Number of JATE ③ Certifiction Number of TELEC ④ Production Years & Months ⑤ Bar Code of IMEI ⑥ IMEI (Production Serial Number) Manufucturer/Applicant : SHARP Corporation ○Location Spec Label and Location 13/Apr/2011 FCC ID

Model Name:SH-10CPhoto(Internal)13th/April/2011 1 / 6 Model Name:SH-10CPhoto(Internal)13th/April/2011 2 / 6 Model Name:SH-10CPhoto(Internal)13th/April/2011 3 / 6 Model Name:SH-10CPhoto(Internal)13th/April/2011 4 / 6 Model Name:SH-10CPhoto(Internal)13th/April/2011 5 / 6 Model Name:SH-10CPhoto(Internal)13th/April/2011 6 / 6

SH-10C UMTS&GSM anttena 74mm UMTS&GSM anttena 74mm Bluetooth&W‐LAN anttena UMTS&GSM anttena 74mm Bluetooth&W‐LAN anttena UMTS&GSM anttena 74mm Bluetooth&W‐LAN anttena UMTS&GSM anttena 74mm Bluetooth&W‐LAN anttena UMTS&GSM anttena 74mm Bluetooth&W‐LAN anttena UMTS&GSM anttena

Model Description FCC ID : APYHRO00145 Destination : Japan Market only Emission Type : GSM ----- GXW : WCDMA ------ F9W Model Name : SH-10C Brand Name : NTT DoCoMo Type of Equipment : Five Band WCDMA(FDD I / V / VI / IX / XIX) and Tri-band GSM(900/1800/1900) Dual mod Cellular Phone with Bluetooth,W-LAN,FeliCa and GPS. RF-section Technical Specification IEEE802.11b/g/n Frequency Band TX 2412MHz to 2472MHz RX 2412MHz to 2472MHz Tx Power 11b:16.5dBm +0.8 / -7.0dB 11g / n:13.0dBm +0.8 / -7.0dB Type of Modulation BPSK, QPSK, 16QAM, 64QAM Transmission Technology DSSS/CCK, OFDM Antenna Integrated Antenna (Common to Bluetooth Antenna) W-LAN Personal Wireless Routers This function does not operate in U.S.A. Technical Specification NFCIP-1(ISO/IEC18092) Frequency Band 13.56 -13.56MHz Type of Modulation ASK(10%) RF ID (FeliCa) Antenna Integrated Loop Antenna Items Technical Specification 3GPP Release 6 WCDMA 850MHz(band V) : Tx 826.4 to 846.6MHz Rx 871.4 to 891.6MHz 800MHz(band VI) : Tx 832.4 to 837.6MHz Rx 877.4 to 882.6MHz 1700MHz(band IX) : Tx 1752.4 to 1782.4MHz Rx 1847.7 to 1877.4MHz 2000MHz(band I) : Tx 1922.6 to 1977.4MHz Rx 2112.6 to 2167.4MHz 800MHz(bandXIX) : Tx 832.4 to 842.6MHz Rx 877.4 to 887.6MHz NOTE: Band I, Band VI, BandIX and BandXIX do not operate in USA Frequency Band GSM 900MHz : Tx 880.2 to 914.8MHz Rx 925.2 to 959.8MHz 1800MHz : Tx 1710.2 to 1784.8MHz Rx 1805.2 to 1879.8MHz 1900MHz : Tx 1850.2 to 1909.8MHz Rx 1930.2 to 1989.8MHz NOTE: GSM900/1800MHz Band do not operate in USA WCDMA : 24dBm+1dB/-3dB Tx Power GSM 900MHz : 33dBm±2dB(GSM/GPRS) 1800MHz : 30dBm±2dB(GSM/GPRS) 1900MHz : 30dBm±2dB(GSM/GPRS) Transmission Technology WCDMA : DS/CDMA, FDD, T/HCDMA GSM : TDMA/FDD Data Transmission WCDMA : Category8 HSDPA(Down Link) Category6 HSUPA(Up Link) GSM : GMSK GSM GPRS : Class 8 (Total 5slots, TX: max 1 / RX: max 4) Voice Codec WCDMA : AMR GSM : EFR/ FR Cellular Phone Antenna Integrated Antenna: L Type Antenna ------ See attached file “antenna.pdf” Technical Specification Bluetooth Version 2.0+EDR Frequency Band TX 2402MHz to 2480MHz RX 2402MHz to 2480MHz Tx Power Class2, Nominal 0dBm (Max +4dBm / min -6dBm) Type of Modulation GFSK,π/4DQPSK, 8DPSK Transmission Technology FHSS Bluetooth Antenna Integrated Antenna ---- See attached file “antenna.pdf” Reversed Mono-pole L-Type / Gain= 2.14dBi Rev4.0 Confidential Class B Personal computer PERIPHERAL DEVICE Items Clock Frequency 48MHz, 480MHz USB USB Data Cable / Connector Shielded / Unshielded Feature SIM Plug-in 3V SIM card slot Display Main 3.4inch, 16,777,216 color TFT(ASV), 854x480(FWVGA) with Backlight Ｓub 1.4inch, 1 color EL, 192x64 Camera Main CCD 16M pixel Ｓub CMOS ＦＷVGA Battery/ Talk time Capacity/voltage 800mAh/ DC3.7V Battery type Rechargeable Lithium-Ion Battery standby time 510h(WCDMA) / 270h(GSM) talk time 220min(WCDMA) / 200min(GSM) Dimensions Target size 52(W) x 113(D) x 15.5(H)mm (Close position) Target weight 139g Cell Phone Feature Key Layout I mode key ,MENU key ,Camera key ,Mail key ,Phone book key , Decision key ,Off hook key ,Clear key , On hook key ,0-9 numeric key ,* key ,# key ,Multi key , 3D key and 1 side key Interface Headset connector For Stereo Headset (10 pins) MCPC connector For USB Cable or PC Link cable or AC Charger or Earphone plug Adaptor SIM card terminal 1 slot SD Card connector For micro SD card (1 slot) Integrated charger circuit The terminals of charging are for using a cradle. External I/F HDMI connector For HDMI Cable. Accessory Battery Lithium-Ion,DC3.7V 800mAh AC Adapter Input AC 100 to 240V Output DC 5.4V/700mA Optional Accessories Stereo Handsfree(Headset) Optional Accessories USB Data Cable Optional Accessories Accessory HDMI Data Cable Optional Accessories

Attachment 1 – System Validation Plots JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/03/31 11:14:13 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Head 835 MHz) DUT: Dipole 835 MHz; Type: D835V2; Serial: 4d081 Communication System: CW; Frequency: 835 MHz;Duty Cycle: 1:1 Medium: HSL900 Medium parameters used: f = 835 MHz; σ = 0.9 mho/m; ε r = 40.6; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: ET3DV6 - SN1679; ConvF(6.2, 6.2, 6.2); Calibrated: 2010/08/20 zSensor-Surface: 4mm (Mechanical Surface Detection) zElectronics: DAE3 Sn508; Calibrated: 2010/11/11 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 2.59 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 55.5 V/m; Power Drift = -0.023 dB Peak SAR (extrapolated) = 3.53 W/kg SAR(1 g) = 2.4 mW/g; SAR(10 g) = 1.57 mW/g Maximum value of SAR (measured) = 2.60 mW/g 0 dB = 2.60mW/g JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/04/01 10:00:10 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Body 835 MHz) DUT: Dipole 835 MHz; Type: D835V2; Serial: 4d081 Communication System: CW; Frequency: 835 MHz;Duty Cycle: 1:1 Medium: M900 Medium parameters used: f = 835 MHz; σ = 0.946 mho/m; ε r = 54; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: ET3DV6 - SN1679; ConvF(6.09, 6.09, 6.09); Calibrated: 2010/08/20 zSensor-Surface: 4mm (Mechanical Surface Detection) zElectronics: DAE3 Sn508; Calibrated: 2010/11/11 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 2.66 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 55.0 V/m; Power Drift = -0.009 dB Peak SAR (extrapolated) = 3.50 W/kg SAR(1 g) = 2.45 mW/g; SAR(10 g) = 1.62 mW/g Maximum value of SAR (measured) = 2.65 mW/g 0 dB = 2.65mW/g JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/03/29 9:45:42 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Head 1900 MHz) DUT: Dipole 1900 MHz; Type: D1900V2; Serial: 5d112 Communication System: CW; Frequency: 1900 MHz;Duty Cycle: 1:1 Medium: HSL1900 Medium parameters used: f = 1900 MHz; σ = 1.45 mho/m; ε r = 39.4; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: ET3DV6 - SN1679; ConvF(4.93, 4.93, 4.93); Calibrated: 2010/08/20 zSensor-Surface: 4mm (Mechanical Surface Detection) zElectronics: DAE3 Sn508; Calibrated: 2010/11/11 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 11.5 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 94.7 V/m; Power Drift = -0.014 dB Peak SAR (extrapolated) = 17.7 W/kg SAR(1 g) = 10.1 mW/g; SAR(10 g) = 5.31 mW/g Maximum value of SAR (measured) = 11.4 mW/g 0 dB = 11.4mW/g JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/03/30 9:49:05 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Body 1900 MHz) DUT: Dipole 1900 MHz; Type: D1900V2; Serial: 5d112 Communication System: CW; Frequency: 1900 MHz;Duty Cycle: 1:1 Medium: M1900 Medium parameters used: f = 1900 MHz; σ = 1.56 mho/m; ε r = 52; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: ET3DV6 - SN1679; ConvF(4.56, 4.56, 4.56); Calibrated: 2010/08/20 zSensor-Surface: 4mm (Mechanical Surface Detection) zElectronics: DAE3 Sn508; Calibrated: 2010/11/11 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 11.6 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 94.0 V/m; Power Drift = -0.024 dB Peak SAR (extrapolated) = 15.9 W/kg SAR(1 g) = 10.1 mW/g; SAR(10 g) = 5.41 mW/g Maximum value of SAR (measured) = 11.5 mW/g 0 dB = 11.5mW/g JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/04/04 9:24:09 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Head 2450 MHz) DUT: Dipole 2450 MHz; Type: D2450V2; Serial: 714 Communication System: CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL2450 Medium parameters used: f = 2450 MHz; σ = 1.84 mho/m; ε r = 39.2; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: ET3DV6 - SN1679; ConvF(4.26, 4.26, 4.26); Calibrated: 2010/08/20 zSensor-Surface: 4mm (Mechanical Surface Detection) zElectronics: DAE3 Sn508; Calibrated: 2010/11/11 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 15.9 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 97.3 V/m; Power Drift = 0.004 dB Peak SAR (extrapolated) = 31.2 W/kg SAR(1 g) = 13.7 mW/g; SAR(10 g) = 6.21 mW/g Maximum value of SAR (measured) = 15.4 mW/g 0 dB = 15.4mW/g JAPAN QUALITY ASSURAN…

Text truncated - open the document above for the full version.

JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 3 – Dosimetric E-Field Probe – ET3DV6, S/N: 1679 Calibration Data JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 4 – System Validation Dipole – D835V2, S/N: 4d081 Calibration Data JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 4 – System Validation Dipole – D1900V2, S/N: 5d112 Calibration Data JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 4 – System Validation Dipole – D2450V2, S/N: 714 Calibration Data

JAPAN QUALITY ASSURANCE ORGANIZATION Page 1 of 37 Technical document No. 23163-0701 JQA File No. : KL80100549 Issue Date : April 8, 2011 TEST REPORT (SAR EVALUATION) APPLICANT : Sharp Corporation, Communication Systems Group ADDRESS : 2-13-1, Iida, Hachihonmatsu, Higashi-Hiroshima City, Hiroshima, 739-0192, Japan PRODUCTS : Cellular Phone MODEL NO. : SH-10C SERIAL NO. : 004401113245134 FCC ID : APYHRO00145 TEST STANDARD : FCC/OET Bulletin 65 Supplement C (Edition 01-01) TESTING LOCATION : Japan Quality Assurance Organization KITA-KANSAI Testing Center 1-7-7, Ishimaru, Minoh-shi, Osaka 562-0027, Japan TEST RESULTS : Passed DATE OF TEST : March 29, 2011 ~ April 5, 2011 This report must not used by the client to claim product endorsement by NVLAP or Kousei Shibata NIST or any agency of the U.S. Government. Manager Japan Quality Assurance Organization KITA-KANSAI Testing Center Testing Dept. EMC Division NVLAP LAB CODE 200191-0 1-7-7, Ishimaru, Minoh-shi, Osaka 562-0027, Japan ● The measurement values stated in Test Report was made with traceable to National Institute of Advanced Industrial Science and Technology (AIST) of Japan, National Institute of Information and Communications Technology (NICT) of Japan , and Laboratory for EMF and Microwave Electronics at the Swiss Federal Institute of Technology (ETH) in Zürich, Switzerland. ● The applicable standard, testing condition and testing method which were used for the tests are based on the request of the applicant. ● The test results presented in this report relate only to the offered test sample. ● The contents of this test report cannot be used for the purposes, such as advertisement for consumers. ● This test report shall not be reproduced except in full without the written approval of JQA. JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80100549 Issue Date : April 8, 2011 Model No. : SH-10C FCC ID : APYHRO00145 Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Page 2 of 37 Technical document No. 23163-0701 TABLE OF CONTENTS Page Documentation ................................................................................................................................................. 3 1 Test Regulation.....................................................................................................................................3 2 Test Location.........................................................................................................................................3 3 Recognition of Test Laboratory............................................................................................................3 4 Description of the Equipment Under Test..........................................................................................4 5 Test Results...........................................................................................................................................4 6 Measurement System Diagram............................................................................................................5 7 System Components..............................................................................................................................6 8 Measurement Process...........................................................................................................................9 9 Measurement Uncertainties...............................................................................................................10 10 Equipment Under Test Modification.................................................................................................11 11 Responsible Party................................................................................................................................11 12 Deviation from Standard....................................................................................................................11 13 Summary..............................................................................................................................................12 14 Test Arrangement...............................................................................................................................13 15 Procedures used to Establish Test Signal.........................................................................................15 Appendix A: Test Data ................................................................................................................................... 20 Appendix B: Test Instruments....................................................................................................................... 36 Appendix C: Attachments .............................................................................................................................. 37 DEFINITIONS FOR ABBREVIATION AND SYMBOLS USED IN THIS TEST REPORT EUT : Equipment Under Test EMC : Electromagnetic Compatibility AE : Associated Equipment EMI : Electromagnetic Interference N/A : Not Applicable EMS : Electromagnetic Susceptibility N/T : Not Tested SAR : Specific Absorption Rate - indicates that the listed condition, standard or equipment is applicable for this report. - indicates that the listed condition, standard or equipment is not applicable for this report. JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80100549 Issue Date : April 8, 2011 Model No. : SH-10C FCC ID : APYHRO00145 Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Page 3 of 37 Technical document No. 23163-0701 Documentation 1 Test Regulation Applied Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Evaluating Compliance with FCC Guidelines for Human Exposure to Radio- frequency Electromagnetic Fields Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions Test Procedure : FCC/OET Bulletin 65 Supplement C (Edition 01-01) IEEE Std.1528–2003 KDB Publicati…

Text truncated - open the document above for the full version.

1/10V C1404 R1201 NC I2C_SCL AGND R1203 I2C_SCL WA223 CN1001 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 AGND GND BIAS OUT CA037 MIC1200 1 2 3 4 5 6 2V8A MAG_DRDY 1/10V C1405 NC AGND 0.1/10V C1401 0.1/10V C1402 () 0.6 0.3 1000p/25V C1201 AGND MAG_DRDY NC I2C_SDA 0.01/10VC1403 2V8A () C1202 GO VOUT CE VIN VSS 6217B18G IC1401 1 23 4 5 () 0 R1202 I2C_SDA 2V8A TEST1 DVDDGND(D)AVDDGND(A) TEST0 REGOUT RST ADR0/SDOADR1/CSB IFS TEST3 INT DRDY SCL/SCK SDA/SDI HSCDTD04 IC1400 1 2 3 4 56 7 8 9101112 13 14 15 16 1 2 ZA001 TA1101 1 2 ZA001 TA1102 0.1/25V C1101 R1101 ZA118 MAGSEN_RST GND MIC_BIAS 2.8V MAG SENSOR GND GND AGND MAG_DRDY I2C_SDA Mic GND CHARGE_D SHARP Confidential I2C_SCL GND CHARGE_D GND CHARGE_D MIC_OUT MAGSEN_RST GND SH-10C Daughter board

NC 100nH L4901 0.047/10V C4912 39nH R4601 TCXO 27.456MHz XA026 X4801 1 Vcon 2 GND 3 Out 4 Vcc 1/10V C4913 1/10V C4801 1500p/25V C4901 RFILRA086AFZZL FL4701 1 IN 2 GND 3 GND 4 OUT 5 GND 1/10V C4903 TP4602 T7SZU04F IC4801 1 NC 2 3 GND 4 5Vcc 0.01/16V C4805 1500p/25V C4902 0.22/10V C4709 NC RFILRA086AFZZL FL4702 1IN 2 GND 3 GND 4 OUT 5 GND 220R4801 CP4802 TP4601 1/10V C4910 0.22/10V C4708 DEMVDD IFOUTIP VCOVSSCPOUT TCXOIN 8 QMAG 10 QSIG 23 1 LNAEV 7 DVDD 24 4 VDD18 18 11 TOP VIEW 22 17 LNAVDD ISIG 25 IFOUTQP PADADCVSS 16 VCOBIAS 21 DEMVSS IFOUTIN 5 LNAVSS AGCCNT IFOUTQN 14 1920 9 IMAG DVSS 2 3 LNAIN 13 12 15 6 IQBCNT IC4900 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 39nH R4602 1/10V C4904 NCNC NC 1A1 1A2 1A3 2A1 1B2 1B3 1B1 20En10En1DIRVCCA2DIR 1A4 2A2 2A32A4VCCBGND2B32B4 1B4 2B2 2B1 GND T7M3245G IC4360 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 17 18 19 20 21 2223 24 CP4005 CP4007 CP4004 CP4059 CP4060 CP4035 CP4036 CP4011 CP4010 CP4034 CP4038 +1V8A_USUAL CP4008 CP4033 CP4037 +3V7_LCD_VBAT CP4121 CP4022 CP4006 CP4061 CP4002 WA211 CN4701 1 Common 2 OpenClose 3 GND 4 GND () *** L4702 CP4020 +3V7_GPS_VBAT +3V7_GPS_VBAT 1/10VC4432 1/10VC4433 () C4011 () C4010 47R4105 10K R4371 0.1/10V C4381 100p/25V C4375 0.1/10V C4361 0.1/10V C4362 1M R4903 470K R4802 33R4804 1000p/25V C4806 1000p/25V C4803 0.1/10V C4906 0.1/10V C4911 100p/25V C4907 0.1/10V C4905 1000p/25V C4710 1.5p/25V C4712 100p/25V C4713 1000p/25V C4701 CP4003 47nH R4014 1.00.5 0.1/25V C4382 RB521S30 D4366 () 0 R4702 CP4001 100p/25VC4005 +3V7_ILL_VBAT () 1000p/25V C4705 IC4701 UPC8236T 1 2 34 5 6 7 QCNCWA320AF11L CN4380 1 2 3 4 5 6 7 8 9 10 11 12 13 +1V8A_USUAL NC 4.7/10V C4412 ZA125 L4402 NC +3V7_ILL_VBAT RB521S30 D4401 NC 1.6 0.8 1.0/35V C4415 +3V7_LCD_VBAT +1V8A_USUAL 1/10V C4418 100 R4402 WA205 QCNCWA205AF04L CN4501 1 2 3 4 5 6 1/10V C4407 GND GND VCC IO GA1S202W IC4401 1 23 4 () 33p/25V C4402 3.3M R4405 ZA127 L4401 1/10VC4408 13 14 21 10 65 161115 37 18 9 8 12 17 4 D B A C E 2928312726 34 23 32 30 2220 35 21 33 2419 25 36 F G 424043 44 3937 414745 48 46 38 TOP VIEW 52495553 5450 51 5957566361 625860 1625734 H 8 C1P C1N C2N C2P CPO CGND DIG[0] DIG[1] DIG[2] CH[5] CH[4] CH[2] CH[3] CH[1] CH[0] GPIO[10]/EN_CH VDD1.8V SDA/SDI SCL/SCK DGND1TEST[0]TEST[1]VPP GPIO[9]/EN_M_PS XRESET IFMODEGPIO[0]/SSGPIO[1]/SDOGPIO[4]GPIO[5]GPIO[6] GPIO[7]/INT GPIO[31]/INT2 GPIO[16]/LPOSCOUTDETINGPIO[3]/DETOUT REG1 VIN2 REG4 REG3 REG2 EN_REG2 DVCC DGND2 LPOSC_TH AGND AVCC GPIO[2]/TXD GPIO[8]/EN_M PD SW VEL VO1 LEDGND M1 SW1 PGND1PGND2 VIN1 PO2SW2VO2 VINCP IR2E63Y7 IC4400 1 2 3 5 6 7 8 9 10 11 12 13 14 16 17 18 20 22 23 24 25 26 27 2829 30 31 32 33 34 35 36 37 38 39 41 43 44 45 49 51 53 54 59 62 15 21 42 46 47 50 55 56 57 58 63 4 19 40 48 52 60 61 1/10V C4419 () C4403 1000p/25V C4401 1/10VC4424 2200p/16V C4406 1/25VC4417 NC 33nH R4407 1SS417 D4402 2.2/6.3V C4404 2.2/6.3V C4409 2.2/6.3V C4410 () C4405 1.0K R4401 4.7/10V C4420 1/10VC4426 DGND DGND DGND DGND CP4039 CP4040 120 R4016 R4010 ZA118 () 0 R4707 R B G CL425FV LED4001 1 2 34 R B G CL425FV LED4005 1 2 34 R B G CL425FV LED4003 1 2 34 R B G CL425FV LED4004 1 2 34 560 R4421 1.0 0.5 1/10V C4302 () C4305 1.0 0.5 1/10V C4301 39 R4308 () C4304 1.0 0.5 1/10V C4303 22 R4305 +1V8A_USUAL 470p/25V C4317 () R4378 47nH R4013 47nH R4015 47nH R4012 CP4012 CP4013 CP4015 CP4014 1.00.5 1/10V C4386 0.1/10V C4385 4.7/10V C4507 RB521S30 D4500 1/10V C4510 1.60.8 4.7/10V C4513 RB521S30 D4501 DEEP_STBY 1/10V C4515 FL4501 NA065 1 2 3 4 5 6 +1V8A_USUAL 1/10V C4512 0.1/10V C4505 2.2/16V C4509 FL4500 NA065 1 2 3 4 5 6 1.6 0.8 2.2/16V C4503 NC FL4502 NA065 1 2 3 4 5 6 QCNCWA319AF41L CN4500 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 1/10V C4514 47nH R4324 47nH R4323 47nH R4321 47nHR4320 47nH R4322 DEEP_STBY NC 1.6 0.8 4.7/6.3V C4506 WA181 CN4300 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 QCNCWA205AF08L CN4370 1 2 3 4 5 6 7 8 9 10 0.01/10V C4703 3.9nH L4707 D4601 VMZ6R8N 0.75p/25V C4706 0.01/10V C4702 () L4706 2.2/16V C4504 2.2/16V C4508 1.60.8 2.2/16V C4511 100nH R4011 100nHR4002 100nHR4003 100nHR4005 NC 1/10V C4388 100K R4387 1/10V C4387 VDDVOUT GND CE GND R103K18D IC4380 1 2 3 4 5 15nH R4382 47nH R4383 100p/25V C4363 () C4373 100p/25V C4364 SWLCD_PWM LCD_5.3V NC NC SWLCD_CTRL2 CP4071 CP4072 R4500 0R4001 0R4004 0R4009 R40070 0 R4100 R40060 0R4104 0R4108 0R4107 0R4101 0R4106 0 R4361 0 R4368 0 R4377 0 R4409 0 R4411 0 R4416 0 R4410 0 R4417 0 R4418 0 R4419 0 R4420 0 R4422 R B G CL425FV LED4002 1 2 34 CP4070 SWLCD_CTRL1 0R4008 EN2 VIN EN1 VOUT2 VOUT1 Vss 6415B427 IC4901 1 2 34 5 6 SWLCD_PWM SWLCD_CTRL1 +1V8A_USUAL BU19801G IC4200 1 CLK_IN 2 VCC2 3CLK_0 4 CLK_EN1 5 VCC1 6 CLK_1 7 CLK_EN2 8 GND 9 CLK_2 0 R4202 1M R4209 SWLCD_CTRL2 0 R4207 0.1/6.3V C4201 1M R4211 0 R4208 0 R4206 0.1/6.3V C4200 WA205 CN4200 1 2 3 4 5 6 1M R4210 0 R4201 LCD_5.3V 0 R4203 SEALD CASE () MA983 SLD4701 1 SEALD CASE MA981 SLD4400 1 WA321 CN4000 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 470p/25V C4308 CDP L4701 8.2nH 6.8nH L4703 100p/25V C4365 100p/25V C4360 33nH L4361 33nH L4360 220p/25V C4516 220p/25V C4517 6.0p/25V R4701 2.7nHC4711 () 330p/50V C4501 () 330p/50V C4502 GPS_IS GPS_IM GPS_QM GPS_QSGPS_AGC1 GPS_AGC4 TSCK RECP RECP RECN RECN MISO_2V85 MOSI_2V85 SSTP_2V85 SSTP_2V85 I2C_SCL0 I2C_SDA0 COG_RESET MUSIC_SYNC MUSIC_SYNC RXD TSCK TXD TSCK NRESETB NRESETB CH5_B2 DIG0 CH1_G1 CH2_B1 CH3_R2 DIG1 CH4_G2 I2C_SCL0 TXD SLCD_CS CH0_R1 GPS_PON GPS_PON GPS_PON GPS_QM GPS_AGC4 GPS_AGC1 RXD RXD OPTICAL_INT OPTICAL_INT DIG2 DIG1 DIG2 LEDR I2C_SCL0 CTCKM LDATA1P CTCKP LDATA1M I2C_SDA0 SCAM_RSTN TP_RESET TP_RESET GPS_IS GPS_IM SLCD_CS SLCD_A0 I2C_SDA0 I2C_SCL0 DATA1N DATA2N DATA1P DATA2P TCKN TCKP AUTO_DETIN SCAM_X_K_VR GPS_CLK LDATA1M TCKN TCKP SCL_2V85 CH1_G1 CH0_R1 CH2_B1 MISO_2V85 EN_M EN_M TXD T…

Text truncated - open the document above for the full version.