APYHRO00167Cellular Phone

’11. ɜ ġ If you lose your FOMA terminal or have it stolen, immediately take the steps necessary for suspending the use of the FOMA terminal. ɜ ġ If the FOMA terminal you purchased is damaged, bring your FOMA terminal to a repair counter specified by DOCOMO after returning to Japan. To prevent damage to the environment, bring used battery packs to a docomo service counter, a docomo agent or a recycle center. Sales : Manufacturer : SHARP Corporation Don’t forget your mobile phone... or your manners! When using your mobile phone in a public place, don’t forget to show common courtesy and consideration for others around you. Universal number international prefixInternational call access codefor the country you stay -81-3-6718-1414 * (toll free) -8005931-8600 * From land-line phonesFrom DOCOMO mobile phones Failures encountered overseas <Network Support and Operation Center> <Universal number> * You might be charged a domestic call fee according to the call rate for the country you stay. ɦ For international call access codes for major countries and universal number international prefix, refer to DOCOMO International Services website. * You are charged a call fee to Japan when calling from a land-line phone, etc. ɦ If you use SH-10C, you should dial the number +81-3-6832-6600 (to enter “+”, press and hold the “0” key for at least one second). * You might be charged a domestic call fee according to the call rate for the country you stay. ɦ For international call access codes for major countries and universal number international prefix, refer to DOCOMO International Services website. * You are charged a call fee to Japan when calling from a land-line phone, etc. ɦ If you use SH-10C, you should dial the number +81-3-6718-1414 (to enter “+”, press and hold the “0” key for at least one second). -8000120-0151 * Universal number international prefix -81-3-6832-6600 * (toll free) International call access codefor the country you stay Loss or theft of FOMA terminal or payment of cumulative cost overseas <docomo Information Center> From DOCOMO mobile phones From land-line phones <Universal number> (available 24 hours a day) (available 24 hours a day) ɦ Unavailable from land-line phones, etc. ɡ From DOCOMO mobile phones (In Japanese only) ɦ Unavailable from land-line phones, etc. (No prefix) 151 (toll free) ɡ From DOCOMO mobile phones (In Japanese only) Repairs (Business hours: 24 hours (open all year round)) (Business hours: 9:00 a.m. to 8:00 p.m.) ɦ Unavailable from part of IP phones. 0120-800-000 (toll free) ɡ From land-line phones (In Japanese only) 0120-005-250 (toll free) ɦ Service available in: English, Portuguese, Chinese, Spanish, Korean. (Business hours: 9:00 a.m. to 8:00 p.m. (open all year round)) ɦ Unavailable from part of IP phones. (No prefix) 113 (toll free) General Inquiries <docomo Information Center> ɜ Please confirm the phone number before you dial. ɜ For Applications or Repairs and After-Sales Service, please contact the above-mentioned information center or the docomo Shop e tc. near you on the NTT DOCOMO website or the i-mode site. i-mode site ȁ iMenu ȁ̤ݖအ΍εȜΠ (user support) ȁΡ΋κΏοΛίġ (docomo Shop) ɦ In Japanese only NTT DOCOMO website ȁ http://www.nttdocomo.co.jp/english/ ɦ Unavailable from part of IP phones. ɡ From land-line phones (In Japanese only) 0120-800-000 (toll free) INSTRUCTION MANUAL SH-10C ’11.5 (1st Edition) 11E SM118 ’11.5 1 t , SaMa 109 ̷͈ఈ Use only the battery packs and adapters specified by NTT DOCOMO for use with the FOMA terminal. May cause fires, burns, bodily injury or electric shock. Do not throw the battery pack into a fire. The battery pack may catch fire, explode, overheat or leak. Do not dispose of used battery packs in ordinary garbage. May cause fires or damage to the environment. Place tape over the terminals to insulate unnecessary battery packs, and take them to a docomo Shop, retailer or institution that handles used batteries in your area. Avoid using the handset in extremely high or low temperatures. Use the FOMA terminal within the range of a temperature between 5°C and 40°C (for temperatures of 36°C or higher, such as in a room with a bath, limit usage to a short period of time) and a humidity between 45% and 85%. Charge battery in areas where ambient temperature is between 5°C and 35°C. 1Set docomo mini UIM card into docomo mini UIM card slot with the IC (gold) side turned down (1) Insert docomo mini UIM card securely (2). Quick Manual CAUTION Before Using Inserting docomo mini UIM card Note that pulling forcibly or adding forces on the lever may damage it. Note that inserting or removing the docomo mini UIM card forcibly may damage the docomo mini UIM card. Notch IC (gold) Notch 110 ̷͈ఈ Perform with the FOMA terminal turned off and closed while holding with your both hands. The battery pack is not waterproof/dust-proof. 1Slide the back cover lever in the direction of the arrow (1) to unlock and remove the back cover (2) The FOMA terminal has a slot to remove the back cover. Securely hold the FOMA terminal as shown in the illustration to prevent excessive force on the back cover and hook a nail on the slot and remove the back cover upward. 2Attach the battery pack Turn the recycle mark side of the battery pack up, match tabs and attach the battery pack. 3Insert the tab of the top of the back cover into the FOMA terminal slot (1), attach it in the direction of the arrow (2) and securely push down with both hands (3) The back of the back cover has also eight tabs to insert the back cover. Securely push tab areas down with both hands so that gaps are not left between the FOMA terminal and the back cover. 4Slide the back cover lever in the direction of the arrow (4) to lock Attaching battery pack Slot Ta b s With a recycle mark side up Using unnecessary force when attaching or removing the battery pack may damage the connector terminal for the battery pack (charger terminal) on the FOMA terminal. Back cover Slot Ta b Securely push tab areas down w…

Text truncated - open the document above for the full version.

Model Name:SH-05DPhoto(External)26th/December/2011 1 / 3 Model Name:SH-05DPhoto(External)26th/December/2011 2 / 3 Model Name:SH-05DPhoto(External)26th/December/2011 3 / 3

Model Name: SH-05D FCC ID: APYHRO00167 ○Spec Label Vendor : NTT DoCoMo ① Color Name ② Approval Number of JATE ③ Certifiction Number of TELEC ④ Production Years & Months ⑤ Bar Code of IMEI ⑥ IMEI (Production Serial Number) Manufucturer/Applicant : SHARP Corporation Caution : Turn off power in an aircraft. Don't remove this seal. ○Location Spec Label and Location 22/Dec/2011 FCC ID

SH-05D Main Antenna(WCDMA Band-I,V,VI) Bluetooth/WLAN 68mm 69mm

Model Name:SH-05DPhoto(Internal)26th/December/2011 1 / 6 Model Name:SH-05DPhoto(Internal)26th/December/2011 2 / 6 Model Name:SH-05DPhoto(Internal)26th/December/2011 3 / 6 Model Name:SH-05DPhoto(Internal)26th/December/2011 4 / 6 Model Name:SH-05DPhoto(Internal)26th/December/2011 5 / 6 Model Name:SH-05DPhoto(Internal)26th/December/2011 6 / 6

Attachment 1 – System Validation Plots JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/12/10 9:48:32 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Head 835 MHz) DUT: Dipole 835 MHz; Type: D835V2; Serial: 4d081 Communication System: CW; Frequency: 835 MHz;Duty Cycle: 1:1 Medium: HSL900 Medium parameters used: f = 835 MHz; σ = 0.892 mho/m; ε r = 42; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: ET3DV6 - SN1679; ConvF(6.24, 6.24, 6.24); Calibrated: 2011/08/18 zSensor-Surface: 4mm (Mechanical Surface Detection) zElectronics: DAE4 Sn508; Calibrated: 2011/11/14 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 2.57 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 56.6 V/m; Power Drift = 0.008 dB Peak SAR (extrapolated) = 3.22 W/kg SAR(1 g) = 2.35 mW/g; SAR(10 g) = 1.56 mW/g Maximum value of SAR (measured) = 2.56 mW/g 0 dB = 2.56mW/g JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/12/11 14:20:56 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Body 835 MHz) DUT: Dipole 835 MHz; Type: D835V2; Serial: 4d081 Communication System: CW; Frequency: 835 MHz;Duty Cycle: 1:1 Medium: MSL900 Medium parameters used: f = 835 MHz; σ = 0.963 mho/m; ε r = 55.3; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: ET3DV6 - SN1679; ConvF(6.18, 6.18, 6.18); Calibrated: 2011/08/18 zSensor-Surface: 4mm (Mechanical Surface Detection) zElectronics: DAE4 Sn508; Calibrated: 2011/11/14 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 2.55 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 54.2 V/m; Power Drift = 0.009 dB Peak SAR (extrapolated) = 3.18 W/kg SAR(1 g) = 2.35 mW/g; SAR(10 g) = 1.58 mW/g Maximum value of SAR (measured) = 2.55 mW/g 0 dB = 2.55mW/g JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/12/13 9:48:14 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Head 2450 MHz) DUT: Dipole 2450 MHz; Type: D2450V2; Serial: 714 Communication System: CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL2450 Medium parameters used: f = 2450 MHz; σ = 1.84 mho/m; ε r = 39; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: EX3DV4 - SN3808; ConvF(7.07, 7.07, 7.07); Calibrated: 2011/09/02 zSensor-Surface: 2mm (Mechanical Surface Detection) zElectronics: DAE4 Sn508; Calibrated: 2011/11/14 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 20.0 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 106.1 V/m; Power Drift = 0.010 dB Peak SAR (extrapolated) = 27.5 W/kg SAR(1 g) = 13.2 mW/g; SAR(10 g) = 6.02 mW/g Maximum value of SAR (measured) = 20.3 mW/g 0 dB = 20.3mW/g JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/12/14 10:21:03 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION System Validation (Body 2450 MHz) DUT: Dipole 2450 MHz; Type: D2450V2; Serial: 714 Communication System: CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: MSL2450 Medium parameters used: f = 2450 MHz; σ = 1.93 mho/m; ε r = 53.3; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: EX3DV4 - SN3808; ConvF(6.85, 6.85, 6.85); Calibrated: 2011/09/02 zSensor-Surface: 2mm (Mechanical Surface Detection) zElectronics: DAE4 Sn508; Calibrated: 2011/11/14 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Antenna Input Power 250 mW/Area Scan (5x5x1): Measurement grid: dx=20mm, dy=20mm Maximum value of SAR (measured) = 18.8 mW/g Antenna Input Power 250 mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 99.3 V/m; Power Drift = 0.009 dB Peak SAR (extrapolated) = 25.9 W/kg SAR(1 g) = 12.9 mW/g; SAR(10 g) = 6.05 mW/g Maximum value of SAR (measured) = 19.6 mW/g 0 dB = 19.6mW/g JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 2-1 – SAR Test Plots (WCDMA Band V) JAPAN QUALITY ASSURANCE ORGANIZATION Date/Time: 2011/12/10 16:14:13 Test Laboratory: JAPAN QUALITY ASSURANCE ORGANIZATION Left Head 4132ch / WCDMA Band V DUT: Cellular Phone; Type: SH-05D; Serial: 004401113775122 Communication System: WCDMA; Frequency: 826.4 MHz;Duty Cycle: 1:1 Medium: HSL900 Medium parameters used: f = 826.4 MHz; σ = 0.882 mho/m; ε r = 42.1; ρ = 1000 kg/m 3 Phantom section: Left Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: zProbe: ET3DV6 - SN1679; ConvF(6.24, 6.24, 6.24); Calibrated: 2011/08/18 zSensor-Surface: 4mm (Mechanical Surface Detection) zElectronics: DAE4 Sn508; Calibrated: 2011/11/14 zPhantom: SAM 1200; Type: QD 000 P40 CA; Serial: 1200 zMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 184 Cheek/Touch Position/Area Scan (11x6x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.826 mW/g Cheek/Touch Position/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 27.2 V/m; Power Drift = -0.011 dB Peak SAR (extrapolated) = 1.14 W/kg SAR(1 g) = 0.873 mW/g; SAR(10 g) …

Text truncated - open the document above for the full version.

JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 3 – Dosimetric E-Field Probe – ET3DV6, S/N: 1679 Calibration Data JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 3 – Dosimetric E-Field Probe – EX3DV4, S/N: 3808 Calibration Data JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 4 – System Validation Dipole – D835V2, S/N: 4d081 Calibration Data JAPAN QUALITY ASSURANCE ORGANIZATION Attachment 4 – System Validation Dipole – D2450V2, S/N: 714 Calibration Data

JAPAN QUALITY ASSURANCE ORGANIZATION Page 1 of 33 Technical document No. 23163-0701 JQA File No. : KL80110478 Issue Date : December 15, 2011 TEST REPORT (SAR EVALUATION) APPLICANT : Sharp Corporation, Communication Systems Group ADDRESS : 2-13-1, Iida, Hachihonmatsu, Higashi-Hiroshima City, Hiroshima, 739-0192, Japan PRODUCTS : Cellular Phone MODEL NO. : SH-05D SERIAL NO. : 004401113775122 FCC ID : APYHRO00167 TEST STANDARD : FCC/OET Bulletin 65 Supplement C (Edition 01-01) TESTING LOCATION : Japan Quality Assurance Organization KITA-KANSAI Testing Center 1-7-7, Ishimaru, Minoh-shi, Osaka 562-0027, Japan TEST RESULTS : Passed DATE OF TEST : December 10 ~ 14, 2011 Kousei Shibata Manager Japan Quality Assurance Organization KITA-KANSAI Testing Center Testing Dept. SAITO EMC Branch 7-3-10, Saito-asagi, Ibaraki-shi, Osaka 567-0085, Japan ● The measurement values stated in Test Report was made with traceable to National Institute of Advanced Industrial Science and Technology (AIST) of Japan, National Institute of Information and Communications Technology (NICT) of Japan , and Laboratory for EMF and Microwave Electronics at the Swiss Federal Institute of Technology (ETH) in Zürich, Switzerland. ● The applicable standard, testing condition and testing method which were used for the tests are based on the request of the applicant. ● The test results presented in this report relate only to the offered test sample. ● The contents of this test report cannot be used for the purposes, such as advertisement for consumers. ● This test report shall not be reproduced except in full without the written approval of JQA. ● VLAC does not approve, certify or warrant the product by this test report. VLAC-001-2 JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110478 Issue Date : December 15, 2011 Model No. : SH-05D FCC ID : APYHRO00167 Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Page 2 of 33 Technical document No. 23163-0701 TABLE OF CONTENTS Page Documentation .............................................................................................................................................. 3 1 Test Regulation......................................................................................................................................3 2 Test Location..........................................................................................................................................3 3 Recognition of Test Laboratory.............................................................................................................3 4 Description of the Equipment Under Test...........................................................................................4 5 Test Results............................................................................................................................................4 6 Measurement System Diagram............................................................................................................5 7 System Components..............................................................................................................................6 8 Measurement Process..........................................................................................................................10 9 Measurement Uncertainties...............................................................................................................11 10 Equipment Under Test Modification..................................................................................................12 11 Responsible Party................................................................................................................................12 12 Deviation from Standard.....................................................................................................................12 13 Summary..............................................................................................................................................13 14 Test Arrangement................................................................................................................................14 15 Procedures used to Establish Test Signal..........................................................................................16 Appendix A: Test Data ................................................................................................................................ 20 Appendix B: Test Setup Photographs ......................................................................................................... 28 Appendix C: Test Instruments .................................................................................................................... 32 Appendix D: Attachments ........................................................................................................................... 33 DEFINITIONS FOR ABBREVIATION AND SYMBOLS USED IN THIS TEST REPORT EUT : Equipment Under Test EMC : Electromagnetic Compatibility AE : Associated Equipment EMI : Electromagnetic Interference N/A : Not Applicable EMS : Electromagnetic Susceptibility N/T : Not Tested SAR : Specific Absorption Rate - indicates that the listed condition, standard or equipment is applicable for this report. - indicates that the listed condition, standard or equipment is not applicable for this report. JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110478 Issue Date : December 15, 2011 Model No. : SH-05D FCC ID : APYHRO00167 Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Page 3 of 33 Technical document No. 23163-0701 Documentation 1 Test Regulation Applied Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Evaluating Compliance with FCC Guidelines for Human Exposure to Radio- frequency Electromagnetic Fields Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions Te…

Text truncated - open the document above for the full version.

JAPAN QUALITY ASSURANCE ORGANIZATION Page 1 of 47 JQA File No. : KL80110479S Issue Date : January 14, 2012 TEST REPORT APPLICANT : Sharp Corporation, Communication Systems Group ADDRESS : 2-13-1, Iida Hachihonmatsu, Higashi-Hiroshima City, Hiroshima, 739-0192, JAPAN PRODUCTS : Cellular Phone MODEL NO. : SH-05D SERIAL NO. : 004401113775130 FCC ID : APYHRO00167 TEST STANDARD : CFR 47 FCC Rules and Regulations Part 22 TESTING LOCATION : Japan Quality Assurance Organization KITA-KANSAI Testing Center 1-7-7, Ishimaru, Minoh-shi, Osaka 562-0027, Japan TEST RESULTS : Passed DATE OF TEST : October 19 ~ 23, 2011 / January 14, 2012 Kousei Shibata Manager Japan Quality Assurance Organization KITA-KANSAI Testing Center Testing Dept. SAITO EMC Branch 7-3-10, Saito-asagi, Ibaraki-shi, Osaka 567-0085, Japan ● The measurement values stated in Test Report was made with traceable to National Institute of Advanced Industrial Science and Technology (AIST) of Japan and National Institute of Information and Communications Technology (NICT) of Japan. ● The applicable standard, testing condition and testing method which were used for the tests are based on the request of the applicant. ● The test results presented in this report relate only to the offered test sample. ● The contents of this test report cannot be used for the purposes, such as advertisement for consumers. ● This test report shall not be reproduced except in full without the written approval of JQA. ● VLAC does not approve, certify or warrant the product by this test report. VLAC-001-2 JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110479S Issue Date : January 14, 2012 Model No. : SH-05D FCC ID : APYHRO00167 Regulation : CFR 47 FCC Rules and Regulations Part 22 Page 2 of 47 TABLE OF CONTENTS Page Documentation ................................................................................................................................................. 3 1 Test Regulation......................................................................................................................................3 2 Test Location..........................................................................................................................................3 3 Recognition of Test Laboratory.............................................................................................................3 4 Description of the Equipment Under Test...........................................................................................4 5 Test Condition........................................................................................................................................5 6 Preliminary Test and Test Setup.........................................................................................................7 7 Equipment Under Test Modification..................................................................................................16 8 Responsible Party................................................................................................................................16 9 Deviation from Standard.....................................................................................................................16 10 Test Results..........................................................................................................................................17 11 Summary..............................................................................................................................................20 12 Operating Condition............................................................................................................................21 13 Test Configuration...............................................................................................................................22 14 Equipment Under Test Arrangement (Drawings)............................................................................23 Appendix A: Test Data ................................................................................................................................... 24 Appendix B: Test Arrangement (Photographs) ............................................................................................. 44 Appendix C: Test Instruments....................................................................................................................... 46 DEFINITIONS FOR ABBREVIATION AND SYMBOLS USED IN THIS TEST REPORT EUT : Equipment Under Test EMC : Electromagnetic Compatibility AE : Associated Equipment EMI : Electromagnetic Interference N/A : Not Applicable EMS : Electromagnetic Susceptibility N/T : Not Tested - indicates that the listed condition, standard or equipment is applicable for this report. - indicates that the listed condition, standard or equipment is not applicable for this report. JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110479S Issue Date : January 14, 2012 Model No. : SH-05D FCC ID : APYHRO00167 Regulation : CFR 47 FCC Rules and Regulations Part 22 Page 3 of 47 Documentation 1 Test Regulation Applied Standard : CFR 47 FCC Rules and Regulations Part 22 Subpart H – Cellular Radiotelephone Service Test Requirements : CFR 47 FCC Rules and Regulations Part 2 §2.1046, §2.1047, §2.1049, §2.1051, §2.1053, §2.1055 and §2.1057 Test Procedure : ANSI C63.4–2003, TIA/EIA–603-C-2004 2 Test Location Japan Quality Assurance Organization (JQA) KITA-KANSAI Testing Center Testing Department SAITO EMC Branch 7-3-10, Saito-asagi, Ibaraki-shi, Osaka 567-0085, Japan MINOH Test Site (KITA-KANSAI Testing Center) 7-7, Ishimaru, 1-chome, Minoh-shi, Osaka, 562-0027, Japan KAMEOKA EMC Branch 9-1, Ozaki, Inukanno, Nishibetsuin-cho, Kameoka-shi, Kyoto, 621-0126, Japan 3 Recognition of Test Laboratory JQA KITA-KANSAI Testing Center Testing Dept. SAITO EMC Branch is accredited under ISO/IEC 17025 by following accreditation bodies and the test facility of Testing Division is registered by t…

Text truncated - open the document above for the full version.

JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110479S Issue Date : January 14, 2012 Model No. : SH-05D FCC ID : APYHRO00167 Regulation : CFR 47 FCC Rules and Regulations Part 22 Page 44 of 47 Appendix B: Test Arrangement (Photographs) Radiated Emission – X-axis – – Y-axis – JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110479S Issue Date : January 14, 2012 Model No. : SH-05D FCC ID : APYHRO00167 Regulation : CFR 47 FCC Rules and Regulations Part 22 Page 45 of 47 – Z-axis – Photograph present configuration with maximum emission The EUT position of the maximum emission at Horizontal Polarization is X-axis. The EUT position of the maximum emission at Vertical Polarization is Z-axis.

JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110478 Issue Date : December 15, 2011 Model No. : SH-05D FCC ID : APYHRO00167 Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Page 28 of 33 Technical document No. 23163-0701 Appendix B: Test Setup Photographs B.1 Left Head – Cheek/Touch Position – – Ear/Tilt Position – JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110478 Issue Date : December 15, 2011 Model No. : SH-05D FCC ID : APYHRO00167 Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Page 29 of 33 Technical document No. 23163-0701 B.2 Right Head – Cheek/Touch Position – – Ear/Tilt Position – JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110478 Issue Date : December 15, 2011 Model No. : SH-05D FCC ID : APYHRO00167 Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Page 30 of 33 Technical document No. 23163-0701 B.3 Body w/ 1.5 cm – Front Side – – Rear Side – JAPAN QUALITY ASSURANCE ORGANIZATION JQA File No. : KL80110478 Issue Date : December 15, 2011 Model No. : SH-05D FCC ID : APYHRO00167 Standard : FCC/OET Bulletin 65 Supplement C (Edition 01-01) Page 31 of 33 Technical document No. 23163-0701 – Rear Side w/ headset –