APYTCG041Monitor

LC-15L1U LIQUID CRYSTAL TELEVISION TÉLÉVISEUR ACL TELEVISOR CON PANTALLA DE CRISTAL LÍQUIDO TELEVISOR DE CRISTAL LÍQUIDO LC-15L1U OPERATION MANUAL MODE D’EMPLOI MANUAL DE OPERACIÓN MANUAL DE OPERAÇÃO ENGLISH FRAN Ç AIS ESPA Ñ OL PORTUGU Ê S SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 SHARP CORPORATION Printed on 100% post-consumer recycled paper. Imprimé sur 100% de papier recyclé. Impreso en 100% de papel reciclado de postconsumo. Papel 100% Reciclado-Cuidado do Meio Ambiente. Printed in Japan Imprimé au Japon Impreso en Japón Impresso no Japão TINS-B124WJZZ 04P02-### ENGLISH 1 LC-15L1U LIQUID CRYSTAL TELEVISION OPERATION MANUAL ENGLISH IMPORTANT INFORMATION WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT: To aid reporting in case of loss or theft, please record the TV’s model and serial numbers in the space provided. The numbers are located at the rear of the TV. U.S.A. ONLY Model No.: Serial No.: 2 CANADA ONLY IMPORTANT INFORMATION (Continued) WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. “Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.” CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eia.org Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. U.S.A. ONLY To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. U.S.A. ONLY U.S.A. ONLY CANADA ONLY ENGLISH 3 CONTENTS Page IMPORTANT INFORMATION ................................... 1 DEAR SHARP CUSTOMER ..................................... 4 IMPORTANT SAFETY PRECAUTIONS .................. 4 REGARDING BATTERY CARE ............................... 7 CORRECT USE OF THE PRODUCT ....................... 9 SUPPLIED ACCESSORIES ................................... 10 PREPARATION ....................................................... 11 TV MAIN UNIT PART NAMES ............................... 14 WIRELESS CENTER PART NAMES ..................... 17 REMOTE CONTROL .............................................. 18 OPERATION FOR TRANSMISSION AND RECEPTION OF VIDEO AND AUDIO SIGNALS ....................................... 19 POWER ................................................................... 20 Turning the Main Power on and off .................. 20 Viewing with a Home AC Wall Outlet ............... 21 EZ SETUP (WITH AUTO CLOCK SETTING) ........ 22 EZ Setup during the First Power On ................ 22 SETTING THE CLOCK ........................................... 24 AUTO CLOCK Setting ....................................... 24 MANUAL CLOCK Setting .................................. 26 TV SIGNALS IN YOUR REGION ........................... 27 BATTERY CHARGE AND TRANSMISSION SETTING .............................................................. 28 Battery Charge .................................................. 28 Transmission Setting ......................................... 28 BASIC OPERATION ............................................... 31 Turning on Power .............................................. 31 Standby .............................................................. 31 Switching TV/VIDEO [AV1/A…

Text truncated - open the document above for the full version.

Page 1 of 2 Front Front with Stand Page 2 of 2 Back Back with Stand

Label Placement

Back with Open battery compartment Disassembly 1 Page 1 of 14 Disassembly 2 Page 2 of 14 LCD Panel Top LCD Panel Bottom Page 3 of 14 PCB Antenna Top PCB Antenna Bottom Page 4 of 14 Battery Terminal Top Battery Terminal Bottom Page 5 of 14 PCB Charge Top PCB Charge Bottom Page 6 of 14 PCB DC Jack Top PCB DC Jap Bottom Page 7 of 14 PCB Inv Top PCB Inv Bottom Page 8 of 14 PCB LED Top PCB LED Bottom Page 9 of 14 PCB OPE Top PCB OPE Bottom Page 10 of 14 PCB Main Top PCB Main Bottom Page 11 of 14 PCB Main SS Top PCB Main SS Top - plate removed Page 12 of 14 PCB Main SS Bottom PCB Main SS Bottom - plate removed Page 13 of 14 PCB Main SS Bottom - plate removed (2) Page 14 of 14

SS Top SS Top without RF SS Bottom PCB SS Bottom Left Monitor PCB SS Bottom Right Main PCB Top - Left upper Main PCB Top - Left Center Main PCB Top - Left Lower Main PCB Top - Center Upper Main PCB Top - Center Middle Main PCB Top - Center Lower Main PCB Top - Right Upper Main PCB Top - Right Middle Main PCB Top - Right Lower RF Bottom RF Bottom without Cover RF Bottom without cover (2) RF Top RF Top without cover RF Top without cover (2) RF PCB Top RF PCB Bottom

A-015-03-C Page 1 of 64 FCC ID: APYTCG041 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan KANSAI ELECTRONIC INDUSTRY DEVELOPMENT CENTER HEAD OFFICE IKOMA TESTING LABORATORY 6-8-7 NISHITENMA 12128 TAKAYAMA-CHO KITA-KU OSAKA 530-0047 JAPAN IKOMA-CITY NARA 630-0101 JAPAN Corporate Juridical Person TEST REPORT Report No.A-015-03-C Date: 13 January 2004 This test report is to certify that the tested device properly complies with the requirements of: FCC Rules and Regulations Part 15 Subpart C Intentional Radiators. All the tests necessary to show compliance to the requirements were performed and these results met the specifications of requirement. The results of this report should not be construed to imply compliance of equipment other than that, which was tested. Unless the laboratory permission, this report should not be copied in part. 1. Applicant Company Name : SHARP CORPORATION ENGINEERING DEPT.1 LCD DIGITAL SYSTEMS DIVISION Mailing Address : 174, Hayakawa-cho, Yaita-city, Tochigi 329-2193 Japan 2. Identification of Tested Device Type of Device : SS Transmitter Type of Modulation : : FHSS : DSSS : Other method Kind of Equipment Authorization : : DoC : Certification : Verification FCC ID : APYTCG041 Device Name : LCD COLOR TV Trade Name : SHARP Model Number : LC-15L1U (Receiver) Serial Number : 001 : Prototype : Pre-production : Production Date of Manufacture : November 2003 3. Test Items and Procedure : 6 dB Bandwidth Measurement : Peak Output Power Measurement : Band Edge RF Conducted Emission Measurement : Spurious RF Conducted Emission Measurement : Power Density Measurement : Radiated Spurious Emission Measurement : AC Power Line Conducted Emission Measurement Above all tests were performed under: FCC Public Notice DA00-705(March 30,2000) and ANSI C63.4 – 1992 : without deviation, : with deviation(details are found inside of this report) 4. Date of Test Receipt of Test Sample : 13 December 2003 Condition of Test Sample : : Damage is not found on the set. : Damage is found on the set. (Details are described in this report) Test Completed on : 17 December 2003 Seiichi Izumi General Manager/ Ikoma Testing Laboratory M040129 A-015-03-C Page 2 of 64 FCC ID: APYTCG041 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan Table of Contents 0. LABORATORY ACCREDITATION AND MEASUREMENT UNCERTAINTY ..................... 3 0.1. Laboratory Accreditation............................................................................................................. 3 0.2. Measurement Uncertainty .......................................................................................................... 3 1. CERTIFICATION OF THE COMPLIANCE ........................................................................... 3 2. GENERAL INFORMATION ................................................................................................... 4 2.1. Product Description ..................................................................................................................... 4 2.2. Description for Equipment Authorization.................................................................................. 5 2.3. Test Facility.................................................................................................................................. 5 3. TESTED SYSTEM ..................................................................................................................6 3.1. Test Mode ..................................................................................................................................... 6 3.2. Operation of EUT System ........................................................................................................... 7 3.3. Characterization and condition of EUT System ........................................................................ 7 3.4. Test Setup Diagram ..................................................................................................................... 8 3.5. Block Diagram of EUT System ................................................................................................. 11 3.6. List of EUT System ................................................................................................................... 12 3.7. List of Cables.............................................................................................................................. 12 4. 6 dB BANDWIDTH MEASUREMENT (§ 15.247 (a) (2))........................................................... 13 4.1. Test Procedure............................................................................................................................ 13 4.2. Test Results ................................................................................................................................ 14 5. PEAK OUTPUT POWER MEASUREMENT (§ 15.247 (b) (3))................................................. 18 5.1. Test Procedure............................................................................................................................ 18 5.2. Test Results ................................................................................................................................ 19 6. BAND EDGE RF CONDUCTED EMISSION MEASUREMENT (§ 15.247 (c))....................... 23 6.1. Test Procedure............................................................................................................................ 23 6.2. Test Results ................................................................................................................................ 24 7. SPURIOUS RF CONDUCTED EMISSION MEASUREMENT (§ 15.247 (c)).......................... 27 7.1. Test Procedure............................................................................................................................ 27 7.2. Test Results .............................................................................…

Text truncated - open the document above for the full version.

A-015-03-C Page 1 of 5 FCC ID: APYTCG041 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan APPENDIX Photographs of EUT System Configuration Tested Item ・6dB Bandwidth Measurement ・Peak Output Power Measurement ・Band Edge RF Conducted Emission Measurement ・Spurious RF Conducted Emission Measurement ・Power Density Measurement A-015-03-C Page 2 of 5 FCC ID: APYTCG041 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan - Continued - A-015-03-C Page 3 of 5 FCC ID: APYTCG041 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan Tested Item ・Radiated Emission measurement FRONT VIEW A-015-03-C Page 4 of 5 FCC ID: APYTCG041 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan - Continued - REAR VIEW A-015-03-C Page 5 of 5 FCC ID: APYTCG041 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan Tested Item ・Conducted Emission measurement