AQF-RA-WN110606CWIFI Module

Forcelink Electronic Co., Ltd. User Manual H/W Version:0.01 IEEE 802.11b/g/n USB Wireless Module 1．Introduction Product Description The RT5370 is a highly integrated MAC/BBP and 2.4 GHz RF/PA/LNA single chip with 150Mbps PHY rate supporting. It fully complies with IEEE 802.11n and IEEE 802.11 b/g feature rich wireless connectivity at high standards, delivers reliable, cost-effective, throughput from an extended distance. Optimized RF architecture and baseband algorithms provide superb performance and low power consumption. Intelligent MAC design deploys a high efficient DMA engine and hardware data processing accelerators without overloading the host processor. The RT5370 is designed to support standard based features in the areas of security, quality of service and international regulation, giving end users the greatest performance anytime in any circumstance. Features *CMOS Technology with PA, LNA, RF, Baseband, and MAC Integrated. *1T1R Mode with 150Mbps PHY Rate for Both Transmit and Receiving. *Legacy and High Throughput Modes *20MHz/40MHz Bandwidth *Reverse Direction Grant Data Flow and Frame Aggregation *WEP 64/128, WPA, WPA2,TKIP, AES, WAPI *QoS-WMM, WMM-PS *WPS,PIN,PBC *Multiple BSSID Support *USB 2.0 *Cisco CCX Support *Bluetooth Co-existence *Low Power with Advanced Power Management *Operating Systems - Windows XP 32/64, 2000, Windows 7,Vista 32/64 , Linux, Macintosh Forcelink Electronic Co., Ltd. 2．simplified block diagram of the RT5370-6P module is depicted in the figure below. Forcelink Electronic Co., Ltd. 3．General Specifications Model Name RA-WN110606B Product Description USB 2.0 Wireless Module WLAN Standard IEEE 802.11 b/g/n ,Wi-Fi compliant Host Interface USB 2.0 Major Chipset Ralink RT5370 Dimension 12mm X 25mm X 1.0mm Weight 4g Operating Conditions Voltage 3.3V/1.8V Operating Temperature -10~50°C Humidity Non-Operating 90% RH non-condensing (12 months among 0~40°C ) Electrical Specfications Frequency Range 2.4~2.4835GHZ Spread Spectrum DSSS 300m(The transmission speed may vary according to the Transmission Distance environment) 11n:150/135/120/90/60//54/45/30/15Mbps 72/65/57.8/43.3/28.9/21.7/14.4/7.2Mbps Data Rate 11b:1/2/5.5/11Mbps 11g:6/9/12/24/36/48/54Mbps Transmit power 13dbm 64/128/152bitWEP,WPA/WPA2,WPA-PSK/WPA2-PSK(TKIP/AE Data security S) Receiver Sensitivity 150M:-71dbm@10%PER 135M: -71dbm@10%PER Forcelink Electronic Co., Ltd. Environment Modulation Type Operating System 54M:-71dbm@10%PER 11M:-84dbm@10%PER 6M:-89dbm@10%PER 1M:-93dbm@10%PER Storage Temperature:-40~70°C(-40°F~158°F) Relative humidity:10%-90% Non-condensing Storage Humidity:5%~95% Non-condensing OFDM/CCK/16-QAM/64-QAM Window98,ME,SE,XP,XP-64 Windows7，32/64, 2000,Vista,linux,mac Forcelink Electronic Co., Ltd. 4．Power Consumption 5. Mechanical Information Positive Negative Forcelink Electronic Co., Ltd. 6．Pin Description J1 1.8V J5 GND J2 3.3V J6 LED J3 D- J4 D+ 7. TEST PARAMETER Test item TX POWER EVM Freq ERR RX SENS Test result (54M) 13.00 dbm -30.19dbm -2.32 khz -73 dbm Forcelink Electronic Co., Ltd. 8．Antenna And Interface Connection Information 1.Interface and the antenna have the option 2. LED PIN have the option with WPS 9.Product ordering information RT5370-6P Module, only support 802.11b/g/n, 3.3V or 3.3V/1.8V voltage And pls mark clearly your need about Antenna、Interface and voltage information. 10. How the host system do the labeling The Host system using this radio module . Should have label indicated ” contains FCC ID: AQF-RA-WN110606C” This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. And (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: This module is only approved on the PCB antenna condition, the antenna connector could not be used with any other antenna by the OEM integrator without the further FCC authorization. This EUT (FCC ID: AQF-RA-WN110606C) doesn’t have Ad Hoc Mode function on “non-US/Canada frequencies”. In addition, the frequency selection feature is disabled by channel 1-11 will be used in North America. County code selection is disabled. Forcelink Electronic Co., Ltd. Important Note: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. this equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Important Note: This module is intended for OEM integrator. The OEM integrator is sti…

Text truncated - open the document above for the full version.

Forcelink Electronic Co., Ltd. 6 Floor, B Block, RunChang Industrial park, Bantian Town, Shenzhen City, China Date:January 27,2013 We, Forcelink Electronic Co., Ltd. declared that this EUT (FCC ID: AQF-RA-WN110606C) doesn’t have Ad Hoc Mode function on "non-US/Canada frequencies". In addition , the frequency selection feature is disabled by firmware for devices marketed to the US/Canada. For DTS part of this device,only channels 1~11 will be used in North America. Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, Contact person:Qingyun Zhang Company:Forcelink Electronic Co., Ltd TEL:(86) 755 28167187 FAX:(86) 755 89501995 E-Mail:[email protected]

Applicant/Grantee Forcelink Electronic Co., Ltd FCC ID: AQF-RA-WN110606C Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the unshielded radio elements. Due to there is no Shielding Part on the EUT, this is a LMA submission. Please see the User Manual for the restricted condition to the OEM integrator. N 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The IC RT5370 control the function to comply with its requirement Y 3 The modular transmitter must have its own power supply regulation. The IC RT5370 control the function to comply with its requirement Y 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. This module uses the PCB antenna to comply with antenna requirement, please see the Internal Photo. Y 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between Tested in a stand-alone configuration, please see the Setup Photo. Y the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. Have FCC identification number and relevant information, please see the Label & User Manual. Y 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the Comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. Y application for equipment authorization. 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is al…

Text truncated - open the document above for the full version.

FCC ID: AQF-RA-WN110606C Label Location on EUT ID Label: Size: 6mm * 12mm WIFI Module M/N: RA-WN110606C FCC ID: AQF-RA-WN110606C Forcelink Electronic Co., Ltd. Made in China

Circuit Description 1、 Basic Functions The Ralink RT5370 is a Wireless LAN (WLAN) USB2.0 network interface controller compatible with the 802.11n specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip. The RT5370 provides a complete solution for a high throughput performance wireless client. The RT5370 baseband implements Orthogonal Frequency Division Multiplexing (OFDM) with 1 transmit and 1 receive path and is compatible with the IEEE 802.11n specification. Features include one spatial stream transmission, short guard interval (GI) of 400ns, spatial spreading, and transmission over 20MHz and 40MHz bandwidth. For legacy compatibility, Direct Sequence Spread Spectrum (DSSS), Complementary Code Keying (CCK) and OFDM baseband processing are included to support all IEEE 802.11b and 802.11g data rates. Differential phase shift keying modulation schemes, data scrambling capability, are available, and CCK provides support for legacy data rates, with long or short preamble. The high-speed FFT/IFFT paths, combined with BPSK, QPSK, 16QAM, and 64QAM modulation of the individual subcarriers and rate compatible punctured convolutiona of 1/2, 2/3, 3/4, and 5/6, provide higher data rates of 54Mbps and 150Mbps for IEEE 802.11g and 802.11n OFDM respectively. The RT5370 supports fast receiver Automatic Gain Control (AGC) with synchronous and asynchronous control loops among antennas, antenna diversity functions, and adaptive transmit power control function to obtain the better performance in the analog portions of the transceiver. 2、Product features Processor: RT5370 Antenna : PCB Antenna Input voltage: Input voltage 5V or 3.3V Operating Systems: Windows XP 32/64, 2000, Windows 7,Vista 32/64 , Linux, Macintosh 3、Circuit Description 1) Power supply Outside input 5 V or 3.3 V , Power is converted to 3.3 or 1.2 Voltage through the DC-DC\LDO, the power supply to the machine; the 1.2V can also output by inside power supply 2）Minimal System RT5370 is CPU+ PA ，Control the work of the various parts of machine and to amplify Wireless signal output 3）Interface The interface is normal USB signal ,it through connet computer then With the computer communications 4）Antenna Processor amplify Wireless signal through the antennaTransmit and to receive wireless AP signal 5）Crystal oscillator The crystal oscillator to provide 40MHZ basic frequency signal to processor Antenna: on board antenna with gain 0dBi. Frequency Range: 2.4~2.4835GHZ Input Voltage: 5V powered by computer or 5V/3.3V powered by other Terminal equipment Radio Frequency Receiving reading device out of radio frequency signal， With induction current gain energy to send out the information stored in the chip. or Active send a signal The other end of the reading device read information and the decoding, Sent to the central information system on data processing. Modulation mode : CCK, DQPSK, DBPSK for DSSS BPSK, QPSK, 16QAM and 64QAM for OFDM Data rate : 11b: 1/2/5.5/11Mbps 11g: 6/9/12/24/36/48/54Mbps 11n HT-20: 72/65/57.8/43.3/28.9/21.7/14.4/7.2Mbps 11n HT-40: 150/135/120/90/60//54/45/30/15Mbps Operating Frequency: 802.11b/g/n-HT20: 2412MHz - 2462MHz 802.11n-HT40: 2422MHz – 2452MHz Number of Channels： 802.11b/g/n-HT20: 11 channels 802.11n-HT40: 7 channels

Forcelink Electronic Co., Ltd. (2013-02-27) Re: RF Exposure Attestation for WIFI Module Model Number RA-WN-110606C FCC ID: AQF-RA-WN-110606C

55 44 33 22 11 D D C C B B A A GND ANTE1E PA_OUT PA_OUT [3] GND GND TitleSize Document Number Rev Date: Sheet of 2-FrontEnd.SCH 2.0 Front-End RALINK TECHNOLOGY, CORP. A 25 Wednesday, June 30, 2010 TitleSize Document Number Rev Date: Sheet of 2-FrontEnd.SCH 2.0 Front-End RALINK TECHNOLOGY, CORP. A 25 Wednesday, June 30, 2010 TitleSize Document Number Rev Date: Sheet of 2-FrontEnd.SCH 2.0 Front-End RALINK TECHNOLOGY, CORP. A 25 Wednesday, June 30, 2010 C55.6pF/NIC55.6pF/NI 12 C61pF/NIC61pF/NI 12 L110pFL110pF 1 2 E1 USB-ANT-RA E1 USB-ANT-RA IO 1 G 2 C7 NI C7 NI 12 55 44 33 22 11 D D C C B B A A UDM UDP PA_OUT+PA_OUT- 1.2VRF 3.3V 3.3VGND GND GND GND 40M_X2 1.2VA LD1P_ACT E-FUSE GND PA_RF_OUT 1.2VPLL 1.2VRF RFO-20 PLL_VC_CAP LED_RDYG#3.3V 1.2VD 1.2VPLL 1.2VD3.3V VRES GPIO9 GND 40MX1 1.2VD3.3V BG_RES_12K RFO+20 40MX2 1.2VRF 3.3VPA RST_N 1.2VRF 3.3VPA GND 1.5V 1.2VPLL 1.5V 1.2VA 1.2VRF 3.3V GND LED_LKACT# 1.2VRF1 BG_3.3A 1.2VA 1.2VD PA_OUT WPS# GND UDP [4] UDM [4] PA_OUT [2] GND GND GND GND GND GND 3.3V GND GND 3.3V GND 1.5V GND GND GND GND GND 3.3V 3.3V GND 3.3V GND GND 1.2VPLL GND 1.2VRF GND 3.3V 1.2VD GND GND GND GND 1.5V GND 1.2VA GND 3.3V TitleSize Document Number Rev Date: Sheet of 3-RT5370-WLAN.SCH 2.0 RT5370-WLAN RALINK TECHNOLOGY, CORP. C 35 Wednesday, June 30, 2010 TitleSize Document Number Rev Date: Sheet of 3-RT5370-WLAN.SCH 2.0 RT5370-WLAN RALINK TECHNOLOGY, CORP. C 35 Wednesday, June 30, 2010 TitleSize Document Number Rev Date: Sheet of 3-RT5370-WLAN.SCH 2.0 RT5370-WLAN RALINK TECHNOLOGY, CORP. C 35 Wednesday, June 30, 2010 C34 close toIC EEPROM GPIO8 ext_pm_mode GPIO9 E-fuse0(Low) LED_RDYG_N Normal disable 1(High) Boot strapping RF_BIST PIN 17 WPS Button R8 330/NI R8 330/NI 1 2 C460.1uFC460.1uF 12 R13 4.7K R13 4.7K 1 2 C8 0.5pF C8 0.5pF 1 2 C47 0.1uF C47 0.1uF 12 R22 4.7K/NI R22 4.7K/NI 1 2 C44 1uF C44 1uF 12 L82.2nHL82.2nH 1 2 C241.2pFC241.2pF 12 R10 100K R10 100K 1 2 C322.2pFC322.2pF 12 C281.2pFC281.2pF 1 2 C23 10pF C23 10pF 12 L622nHL622nH 1 2 C421uFC421uF 12 D2 LED D2 LED 1 2 C1327pFC1327pF 1 2 C41 4.7uF C41 4.7uF 12 L71.5nHL71.5nH 1 2 R2300RR2300R 1 2 C37 0.1uF C37 0.1uF 12 2.5x3.2 U3 XTAL/3.2x2.5/40MHz 2.5x3.2 U3 XTAL/3.2x2.5/40MHz 12 43 R6 4.7K R6 4.7K 1 2 C29 1.2pF C29 1.2pF 12 C401uFC401uF 12 C30 33pF C30 33pF 1 2 U4 RT5370-QFN52-7.5X5.7 U4 RT5370-QFN52-7.5X5.7 RF_INN 1 RF_INP 2 RF_V12A 3 PA_V33P 4 PA_OUTP 5 PA_OUTN 6 PA_V33N 7 PA1_V33A 8 VDD 9 VCCIO 10 RST_N 11 LDO_CORE_VO12 12 LDO_CORE_VI15 13 VDDL 14 PADP 15 PADM 16 VDDA 17 VRES 18 GPIO2 19 GPIO3 20 GPIO8 21 GPIO9 22 GPIO10/FLASH_CSN 23 GPIO11 24 TEST_EN 25 VCCIO 26 LED_ACT_N 27 LED_RDYG_N 28 GPIO0 29 GPIO1 30 GPIO4/EECS 31 GPIO5/EEDI 32 VDD 35 PLL_AVDD_V12A 36 ADC_V12D 38 RF_BB2_V12A 40 BG_RES 41 BG_V33A 42 LDORF_OUT 43 LDOPLL_OUT 45 LDORF_IN 44 PLL_X2 46 PLL_X1 47 PLL_PRE_V12A 48 PLL_VC_CAP 49 VCO_LO_V12A 50 RF_BB1_V12A 51 RF0_LO_V12A 52 GND 53 GPIO6/EESK 33 GPIO7/EEDO 34 PLL_DVDD_V12D 37 ADC_V12A 39 L11 0 ohm L11 0 ohm 1 2 C3410pFC3410pF 12 C26 0.1uF C26 0.1uF 12 R15 4.7K R15 4.7K 1 2 C22100pF/NIC22100pF/NI 1 2 R16 8.2K R16 8.2K 12 L102.2nHL102.2nH 12 L510nHL510nH 1 2 C43 1uF C43 1uF 12 C33 33pF C33 33pF 1 2 C39 0.1uF C39 0.1uF 12 R3 12KR3 12K 1 2 L9 0 ohm L9 0 ohm 1 2 C35 0.1uF C35 0.1uF 1 2 C2122nFC2122nF 12 R9 330 R9 330 1 2 C450.1uFC450.1uF 12 C271.2pFC271.2pF 12 C540.1uFC540.1uF 12 C311.2pF/NIC311.2pF/NI 12 C20 0.1uF C20 0.1uF 12 C36 1pF C36 1pF 12 C491uFC491uF 12 R12 4.7K/NI R12 4.7K/NI 1 2 S1 SW TACT-TS11M/NI S1 SW TACT-TS11M/NI 1 3 2 4 C48 0.1uF C48 0.1uF 12 55 44 33 22 11 D D C C B B A A UDPUDM UV+ UDM [3] UDP [3] UV+ GND UV+ 3.3V GND GND GND GND UV+ GND UV+ 1.5V UV+ GND TitleSize Document Number Rev Date: Sheet of 4-USB-A.SCH 2.0 PEN USB Interface and Power RALINK TECHNOLOGY, CORP. B 45 Thursday, November 25, 2010 TitleSize Document Number Rev Date: Sheet of 4-USB-A.SCH 2.0 PEN USB Interface and Power RALINK TECHNOLOGY, CORP. B 45 Thursday, November 25, 2010 TitleSize Document Number Rev Date: Sheet of 4-USB-A.SCH 2.0 PEN USB Interface and Power RALINK TECHNOLOGY, CORP. B 45 Thursday, November 25, 2010 C24.7uFC24.7uF 1 2 C3 22pF C3 22pF 1 2 L22.2uHL22.2uH 12 U2 XCS621B U2 XCS621B EN 1 GND 2 SW 3 VIN 4 VFB 5 C94.7uFC94.7uF 1 2 C44.7uFC44.7uF 12 U1 XCS621B U1 XCS621B EN 1 GND 2 SW 3 VIN 4 VFB 5 L32.2uHL32.2uH 12 1234 G +-V GNC NC J1 USB_A-PLUG 1234 G +-V GNC NC J1 USB_A-PLUG 2341 R5 300K R5 300K 1 2 C14.7uFC14.7uF 12 R1 300K R1 300K 1 2 R4 300K R4 300K 1 2 C3 22pF C3 22pF 1 2 R7 300K R7 300K 1 2

Page 1 FCC ID TEST REPORT for WIFI Module MODEL: RA-WN110606C Trade Mark: N/A Integrated circuit Factory: MediaTek Integrated circuit Model: RT5370 FCC ID: AQF-RA-WN110606C Test Report Number: 1301001000 Issued Date: January 21, 2013 Issued for Forcelink Electronic Co., Ltd. 6 Floor, B Block, RunChang Industrial park, Bantian Town, Shenzhen City, China Issued By: SHENZHEN TIMEWAY TECHNOLOGY CONSULTING CO., LTD. 5/F,Block 4, Anhua Industrial Zone., No.8 Tairan Rd. Chegongmiao, Futian District Shenzhen, China TEL: +86-755-83448688 FAX: +86-755-83442996 Report No.: 1301001000 Issued: January 21, 2013 Revised: None FCC ID: AQF-RA-WN110606C TRF No.: FCC PART 15C-15.247/A0 Page 2 of 70 . TABLE OF CONTENTS 1 TEST CERTIFICATION....................................................................................................................... 3 2 TEST RESULT SUMMARY ............................................................................................................ 4 3 EUT DESCRIPTION............................................................................................................................ 5 4 SETUP OF EQUIPMENT UNDER TEST AND TEST EQUIPMENTS USED................................. 6 4.1. DESCRIPTION OF SUPPORT UNITS ................................................................................................. 7 4.2. Description of Test Configuration.......................................................................................................... 7 4.3. CONFIGURATION OF SYSTEM UNDER TEST .................................................................................. 8 4.4. Justification .......................................................................................................................................... 8 5 FACILITIES AND ACCREDITATIONS .......................................................................................... 9 5.1. FACILITIES ........................................................................................................................................... 9 5.2. MEASUREMENT UNCERTAINTY...................................................................................................... 10 §15.203 - ANTENNA REQUIREMENT ................................................................................................ 11 Standard Applicable ................................................................................................................................... 11 Antenna Connector Construction ............................................................................................................... 11 §15.207 - CONDUCTED EMISSIONS ................................................................................................. 12 Applicable Standard ................................................................................................................................... 12 Test Procedure ........................................................................................................................................... 12 Environmental Conditions .......................................................................................................................... 12 Plot(s) of Test Data .................................................................................................................................... 12 §15.209, §15.205, §15.247(D) - SPURIOUS EMISSIONS ................................................................... 15 Test Equipment .......................................................................................................................................... 15 Test Procedure ........................................................................................................................................... 15 Environmental Conditions .......................................................................................................................... 15 Radiated Test Setup................................................................................................................................... 15 Radiated Emission Limit............................................................................................................................. 16 §15.247(A) (2) – 6DB BANDWIDTH TESTING ................................................................................... 35 Test Equipment .......................................................................................................................................... 35 Test Procedure ........................................................................................................................................... 35 Environmental Conditions .......................................................................................................................... 35 Applicable Standard ................................................................................................................................... 35 Test Result: Pass. ...................................................................................................................................... 36 §15.247(B) (3) - MAXIMUM PEAK OUTPUT POWER ........................................................................ 43 Test Equipment .......................................................................................................................................... 43 Test Procedure ........................................................................................................................................... 43 Environmental Conditions .......................................................................................................................... 43 Applicable Standard ................................................................................................................................... 43 Test Result .................................................................…

Text truncated - open the document above for the full version.

CONDUCTED EMISSION TEST CONDUCTED EMISSION TEST RADIATED EMISSION TEST RADIATED EMISSION TEST