AQF-WN11062AWIFI Module

RASINTECHNOLOGY (H.K.) CO.LIMITED RA－WN11062A IEEE 802.11b/g/n USB Wireless Module Datasheet Version A2 Document Release Date Modification Initials Approved 1．First version Version A1 2010/12/27 Qiu Version A2 2010/04/14 Qiu 1．Second version RASIN TECHNOLOGY (H.K.) CO., LIMITED http://www.rasintech.com.cn RASINTECHNOLOGY (H.K.) CO.LIMITED 1．Introduction Product Description The RT5370 is a highly integrated MAC/BBP and 2.4 GHz RF/PA/LNA single chip with 150Mbps PHY rate supporting. It fully complies with IEEE 802.11n and IEEE 802.11 b/g feature rich wireless connectivity at high standards, delivers reliable, cost-effective, throughput from an extended distance. Optimized RF architecture and baseband algorithms provide superb performance and low power consumption. Intelligent MAC design deploys a high efficient DMA engine and hardware data processing accelerators without overloading the host processor. The RT5370 is designed to support standard based features in the areas of security, quality of service and international regulation, giving end users the greatest performance anytime in any circumstance. Features *CMOS Technology with PA, LNA, RF, Baseband, and MAC Integrated. *1T1R Mode with 150Mbps PHY Rate for Both Transmit and Receiving. *Legacy and High Throughput Modes *20MHz/40MHz Bandwidth *Reverse Direction Grant Data Flow and Frame Aggregation *WEP 64/128, WPA, WPA2,TKIP, AES, WAPI *QoS-WMM, WMM-PS *WPS,PIN,PBC *Multiple BSSID Support *USB 2.0 *Cisco CCX Support *Low Power with Advanced Power Management *Operating Systems - Windows XP 32/64, 2000, Windows 7,Vista 32/64 , Linux, Macintosh RASIN TECHNOLOGY (H.K.) CO., LIMITED http://www.rasintech.com.cn RASINTECHNOLOGY (H.K.) CO.LIMITED 2．simplified block diagram of the RX5370A module is depicted in the figure below. RASIN TECHNOLOGY (H.K.) CO., LIMITED http://www.rasintech.com.cn RASINTECHNOLOGY (H.K.) CO.LIMITED 3．General Specifications Model Name RA-WN11062A Product Description USB 2.0 Wireless Module WLAN Standard IEEE 802.11 b/g/n ,Wi-Fi compliant Host Interface USB 2.0 Major Chipset Ralink RT5370 Dimension 11mm X 34mm X 3.3mm Weight 5g Operating Conditions Voltage Operating Temperature -10~50°C Humidity Non-Operating 90% RH non-condensing (12 months among 0~40°C ) Electrical Specfications Frequency Range 2.412~2.462GHZ Spread Spectrum DSSS 300m(The transmission speed may vary according to the Transmission Distance environment) 11n:150/135/120/90/60//54/45/30/15Mbps 72/65/57.8/43.3/28.9/21.7/14.4/7.2Mbps 11b:1/2/5.5/11Mbps 11g:6/9/12/24/36/48/54Mbps Data Rate 11b:1/2/5.5/11Mbps 11g:6/9/12/24/36/48/54Mbps Transmit power 14.12dbm 64/128/152bitWEP,WPA/WPA2,WPA-PSK/WPA2-PSK(TKIP/AE Data security S) Receiver Sensitivity 150M:-71dbm@10%PER 135M: -71dbm@10%PER RASIN TECHNOLOGY (H.K.) CO., LIMITED http://www.rasintech.com.cn RASINTECHNOLOGY (H.K.) CO.LIMITED Environment Modulation Type Operating System 54M:-71dbm@10%PER 11M:-84dbm@10%PER 6M:-89dbm@10%PER 1M:-93dbm@10%PER Storage Temperature:-40~70°C(-40°F~158°F) Relative humidity:10%-90% Non-condensing Storage Humidity:5%~95% Non-condensing OFDM/CCK/16-QAM/64-QAM Window98,ME,SE,XP,XP-64 Windows7，32/64, 2000,Vista,linux,mac 4．Power Consumption RASIN TECHNOLOGY (H.K.) CO., LIMITED http://www.rasintech.com.cn RASINTECHNOLOGY (H.K.) CO.LIMITED 5. Mechanical Information LED G + - V+ 5 pin (pin to pin=2.54mm) RASIN TECHNOLOGY (H.K.) CO., LIMITED http://www.rasintech.com.cn RASINTECHNOLOGY (H.K.) CO.LIMITED 6．Pin Description J1 VCC J5 LED J2 UDM J3 UDP J4 GND 7. TEST PARAMETER Test item TX POWER EVM Freq ERR RX SENS Test result (54M) 14.12 dbm -32.17dbm -2.32 khz -70 dbm RASIN TECHNOLOGY (H.K.) CO., LIMITED http://www.rasintech.com.cn 8．Antenna And Interface Connection Information Interface and the antenna have the option 9. Product ordering information RA－WN11062A CHIPSET, only support 802.11b/g/n, 5V voltage support RA－WN11062A CHIPSET, only support 802.11b/g/n, 3.3V voltage support And pls mark clearly your need about usb connection information. 10. How the host system do the labeling The Host system using this radio module , should have label indicated “contains FCC ID: AQF-WN11062A” This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. RASIN TECHNOLOGY (H.K.) CO., LIMITED http://www.rasintech.com.cn FCC warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the…

Text truncated - open the document above for the full version.

SCS-F26 Modular Approval Letter Page 1 of 2 Rev 4.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Modular Approval Declaration Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (Obsolete) 1.0 1.0 Dec-04-2006 Added IC Modular Letter (Obsolete) 1.0 2.0 Feb 16 2009 Add LMA and MA option (Obsolete) 2.0 3.0 April 14 2010 Revised per RSS Gen issue 3.0 3.0 4.0 Jan 12 2011 SCS-F26 Modular Approval Letter Page 2 of 2 Rev 4.0 (Forcelink Electronic Co., Ltd) (02/16/2012) (WIFI Module) FCC ID : AQF-WN11062A , is seeking FCC Authorization as a Single Modular transmitter / Single Limited Modular Approval (Please check one). The EUT meets the requirements for Single Modular approval / Single Limited Modular Approval (please check one) as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below : Questions are: 1. “The modular transmitter must have its own RF shielding.” Yes / No 2. “The modular transmitter must have buffered modulation/data inputs.” Yes / No 3. “The modular transmitter must have its own power supply regulation.” Yes / No 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(c).” Yes / No 5. “The modular transmitter must be tested in a stand-alone configuration.” Yes / No 6. “The modular transmitter must be labeled with its own FCC ID number.” Yes / No 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacture must provide adequate instruction along with the module to explain any such requirements.” Yes / No 8. “The modular transmitter must comply with any applicable RF exposure requirements.” Yes / No Note: (1) LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured. (2) Host devices which contain separately certified modules do not need to be recertified, provided that they meet the following conditions: (i) The host device, as a stand-alone unit without any separately certified modules, complies with all applicable Radio Standards Specifications. (ii) The host device and all the separately certified modules it contains jointly meet the RF exposure compliance requirements of RSS-102, if applicable. (iii) The host device complies with the certification labeling requirements of each of the modules it contains. Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. Client’s signature Client’s name / title Qingyun Zhang /Manager Contact information / address 6 Floor, B Block, RunChang Industrial Park, Bantian Town, Shenzhen City, China

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 Forcelink Electronic Co., Ltd (2012-02-16) To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, ___ Forcelink Electronic Co., Ltd _ hereby authorize SIEMIC.INC to act as a Certification Body for certifying for the following project(s): (Product description: WIFI Module model name: RA-WN11062A, RA-WN11060A, RA-WN11061A, RA-WN11063A, RA- WN11064A, RA-WN11065A FCC ID: AQF-WN11062A We affirm that between SIEMIC and ___ Forcelink Electronic Co., Ltd __, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature Client’s name / title: Qingyun Zhang/ Manager Contact information / address: 6 Floor, B Block, RunChang Industrial Park, Bantian Town, Shenzhen City, China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 1.0 2.0 August – 11 - 2008 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 2.0 (Forcelink Electronic Co., Ltd) (2012-02-16) To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: AQF-WN11062A We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic - The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Client’s name / title: Qingyun Zhang /Manager Contact information / address: 6 Floor, B Block, RunChang Industrial Park, Bantian Town, Shenzhen City, China

INTERIOR PHOTOGRAPHY WIFI Antenna

FCC ID: AQF-WN11062A Label Location on EUT ID Label: FCC ID: AQF-WN11062A MADE IN CHINA

INTERIOR PHOTOGRAPHY WIFI Antenna

MAXIMUM PERMISSION EXPOSURE TEST REPORT FCC ID : AQF-WN11062A Mobile device According to §15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 Test Results: Frequency (MHz) RF power (mW) antenna gain Measured Power Density(mW/cm 2 ) Limit(mW/cm 2 )Result 2412 25.8 0dBi 0.00514 1.0 Pass 2437 24.7 0dBi 0.00492 1.0 Pass 2462 22.7 0dBi 0.00452 1.0 Pass S=PG/4PiR 2

Page 1 FCC ID TEST REPORT for WIFI Module MODEL: RA-WN11062A, RA-WN11060A, RA-WN11061A, RA-WN11063A, RA-WN11064A, RA-WN11065A Trade Mark: N/A FCC ID: AQF-WN11062A Test Report Number: WSCT12020061E Issued Date: February 17, 2012 Issued for Forcelink Electronic Co., Ltd 6 Floor, B Block , RunChang Industrial Park , Bantian Town, Shenzhen City, China Issued By: World Standardization Certification & Testing CO., LTD. Building A, Baoshi Road, Baoshi Science & Technology Park, Bao’an District, Shenzhen, Guangdong, China TEL: +86-755-26996192 FAX: +86-755-26996253 Note: This report shall not be reproduced except in full, without the written approval of World Standardization Certification& Testing CO., LTD. This document may be altered or revised by World Standardization Certification& Testing CO., LTD. Personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Report reference No.:WSCT12020061E Issued: February 17, 2012 Revised: None TRF No.: FCC PART 15C-15.247/A0 Page 2 of 54 FCC ID: AQF-WN11062A This report shall not be reproduced except in full, without the written approval of World Standardization Certification & Testing CO., LTD. Revision History Of Report Rev. Issue No. Revisions Effect Page Revised By 00 WSCT12020061E Initial Issue ALL Kallen Wang Report reference No.:WSCT12020061E Issued: February 17, 2012 Revised: None TRF No.: FCC PART 15C-15.247/A0 Page 3 of 54 FCC ID: AQF-WN11062A This report shall not be reproduced except in full, without the written approval of World Standardization Certification & Testing CO., LTD. TABLE OF CONTENTS 1 TEST CERTIFICATION .................................................................................................. 4 2 TEST RESULT SUMMARY ....................................................................................... 5 3 EUT DESCRIPTION ....................................................................................................... 6 4 SETUP OF EQUIPMENT UNDER TEST AND TEST EQUIPMENTS USED ............. 7 4.1. DESCRIPTION OF SUPPORT UNITS ................................................................................. 8 4.2. CONFIGURATION OF SYSTEM UNDER TEST .................................................................. 8 5 FACILITIES AND ACCREDITATIONS ...................................................................... 9 5.1. FACILITIES ........................................................................................................................... 9 5.2. ACCREDITATIONS .............................................................................................................. 9 5.3. MEASUREMENT UNCERTAINTY ........................................................................................ 9 §15.203 - ANTENNA REQUIREMENT ............................................................................ 10 Standard Applicable ................................................................................................................... 10 Antenna Connector Construction ............................................................................................... 10 §15.207 - CONDUCTED EMISSIONS ............................................................................. 11 Applicable Standard ................................................................................................................... 11 Test Procedure .......................................................................................................................... 11 Plot(s) of Test Data .................................................................................................................... 11 §15.209, §15.205, §15.247(d) - SPURIOUS EMISSIONS ............................................... 14 Test Equipment .......................................................................................................................... 14 Test Procedure .......................................................................................................................... 14 Radiated Test Setup .................................................................................................................. 14 Radiated Emission Limit............................................................................................................. 15 Radiated Emission Test Result .................................................................................................. 15 §15.247(a) (2) – 6dB BANDWIDTH TESTING ................................................................ 30 Test Equipment .......................................................................................................................... 30 Test Procedure .......................................................................................................................... 30 Applicable Standard ................................................................................................................... 30 Test Result: Pass. ...................................................................................................................... 30 §15.247(b) (3) - MAXIMUM PEAK OUTPUT POWER .................................................... 36 Test Equipment .......................................................................................................................... 36 Test Procedure .......................................................................................................................... 36 Applicable Standard ................................................................................................................... 36 Test Result ................................................................................................................................. 37 §15.247(d) – 100 kHz BANDWIDTH OF FREQUENCY BAND EDGE ........................... 38 Test Equipment ...........................................................…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOGRAPHY CONDUCTED EMISSION TEST EUT RADIATED EMISSION TEST BELOW 1GHz EUT EUT Connect to PC RADIATED EMISSION TEST ABOVE 1GHz EUT