B3Q8V9313Mobile Printer

Product Safety Guide PJ-722/PJ-723/PJ-762/PJ-763/ PJ-763MFi PJ-773 Be sure to read this document before using the printer. We recommend that you keep this document nearby for future reference. US ENG 1 English Introduction Thank you for purchasing the PocketJet PJ-722/PJ-723/PJ-762/PJ-763/PJ-763MFi/PJ-773 (hereafter referred to as “the printer”) The documentation included with the printer, including the Product Safety Guide (this document) and the User's Guide contains operating precautions and basic instructions. For more information, and for information about software and using the printer on a network, see the Online User’s Guide, which can be found on the Brother Solutions Center. The latest version of your printer's documentation is available from the Brother Solutions Center at support.brother.com/ . Save all documentation for later reference. Important Notice The contents of this document are subject to change without notice. The contents of this document may not be duplicated or reproduced, partially or in full, without permission. We assume no responsibility for damages arising from earthquakes, fire, other disasters, actions of third parties, the user’s intentional or negligent operation, misuse or operation under other special conditions. We assume no responsibility for damage (such as losses, loss of business profits, lost profits, business disruptions or a lost means of communication) that may result from the use or inability to use of the printer. If the printer should be defective due to faulty manufacturing, we shall replace or repair it during the warranty period. We assume no responsibility for any damages that may result from incorrect operation of the printer caused by connecting incompatible equipment or using incompatible software. 2 To use the printer safely If the printer malfunctions, immediately stop using it, and then contact your Brother dealer. Symbols used in this document The following symbols are used throughout this document: DANGER Indicates an imminently hazardous situation which, if the product is handled without following the warnings and instructions, will result in death or serious injuries. WARNING Indicates a potentially hazardous situation which, if the product is handled without following the warnings and instructions, could result in death or serious injuries. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injuries. IMPORTANT Indicates a potentially hazardous situation which, if not avoided, may result in damage to property or loss of product functionality. Indicates a risk of fire under certain circumstances Indicates a risk of electric shock under certain circumstances Indicates a risk of burns under certain circumstances Indicates an action that must not be performed Indicates a risk of combustion if fire is nearby Indicates a risk of injury if the indicated part of the printer is touched Indicates a risk of injury, such as electric shock, if the indicated part of the printer is disassembled Indicates a risk of electric shock if the operation is performed with wet hands Indicates a risk of electric shock if the printer is exposed to water Indicates an action that must be performed Indicates that the AC power cord must be disconnected from the electrical outlet 3 English Important safety instructions DANGER Rechargeable Li-ion battery (Optional) Carefully observe the following precautions for the rechargeable Li-ion battery (hereafter referred to as "rechargeable battery"). If these precautions are not followed, overheating, leaking, or cracks in the battery may result in an electrical short, explosion, smoke, fire, electric shock, injury to yourself or others, or damage to the product or other property. Use the rechargeable battery only for its intended purpose. The printer and rechargeable battery are designed to be used together exclusively. DO NOT insert the rechargeable battery into a different printer, or a different rechargeable battery into your printer, otherwise a fire or damage may occur. To charge the rechargeable battery, insert it into the printer, and then use the AC adapter designed specifically for this printer. DO NOT charge the rechargeable battery near a fire or in direct sunlight. This could activate the protection circuitry, which is designed to prevent danger from high heat. Activation of the protection circuitry could cause charging to stop, charging to occur with excessive current/voltage if the protection circuitry fails, or an abnormal chemical reaction within the battery. When charging the rechargeable battery, use only the battery charger designed specifically for your rechargeable battery. DO NOT allow wires or other metal objects to come into contact with the terminals of the rechargeable battery. DO NOT carry or store the rechargeable battery with metal objects, such as necklaces or hairpins. This could cause an electrical short, and metal objects such as wires, necklaces, or hairpins to overheat. DO NOT use or leave the rechargeable battery near fire, heaters, or other high-temperature (above 176F/80°C) locations. DO NOT allow the rechargeable battery to come into contact with or to be immersed in water. DO NOT use the rechargeable battery in corrosive environments, such as areas where salty air, salt water, acids, alkalis, corrosive gases, chemicals, or any corrosive liquid is present. DO NOT use the rechargeable battery if it is damaged or leaking. DO NOT directly solder any connections to the rechargeable battery. This could cause internal insulation to melt, gas to be emitted, or safety mechanisms to fail. DO NOT use the rechargeable battery with the polarity (+) (-) reversed. Check the orientation of the rechargeable battery before inserting it, and do not try to force the rechargeable battery into the printer. Charging the rechargeable battery with the polarity reversed could cause an abnormal chemical reaction within the recha…

Text truncated - open the document above for the full version.

The following manuals are available for this printer. You can download the latest manuals from the Brother Solutions Center at support.brother.com . 1 Printed manual in the box 2 PDF manual on the Brother Solutions Center website 1 (Power) button 2 (Feed) button 3 (Bluetooth) button (PJ-762/PJ-763/PJ-763MFi only) (Wi-Fi) button (PJ-773 only) 4POWER indicator 5DATA indicator 6STATUS indicator 7 (Bluetooth) indicator (PJ-762/PJ-763/PJ-763MFi only) (Wi-Fi) indicator (PJ-773 only) 8Release cover 9Paper outlet slot 10 Tear bar 11 Paper input slot 12 USB port 13 DC connector 14 Battery latches 15 Battery cavity mounting block LED Indicators The indicators light and flash to indicate the printer’s status. Each indicator may light or flash in green, red, orange or blue. Available Manuals Product Safety Guide 1 This guide provides safety information; read it before you use the printer. User's Guide 1 This guide provides basic information about using the printer along with detailed troubleshooting tips. Online User’s Guide 2 This guide includes the contents of the User’s Guide, and additional information about the printer settings and operations, network connection and settings, troubleshooting tips, and maintenance instructions. AirPrint Guide 2 This guide provides information for using AirPrint to print from a Mac or iOS device. Google Cloud Print Guide 2 This guide provides details on how to use Google Cloud Print™ services for printing over the Internet. Mobile Print/Scan Guide for Brother iPrint&Scan 2 This guide provides useful information about printing from your mobile device when the printer and the device are connected using Bluetooth or Wi-Fi ® . P-touch Template Manual 2 This manual provides information on P-touch Template. Raster Command Reference 2 This manual provides information about printer control commands for controlling the printer directly. PJ-722/PJ-723/PJ-762/PJ-763/PJ-763MFi/PJ-773 English Thank you for purchasing the Brother PocketJet PJ-722/PJ-723/PJ-762/ PJ-763/PJ-763MFi/PJ-773 thermal mobile printer. We recommend that you keep this document nearby for future reference. To download the latest manuals, please visit the Brother Solutions Center (support.brother.com/ ) where you can also download the latest drivers and applications for your printer, read FAQs and troubleshooting tips and learn about special printing solutions. User’s Guide Printed in USA LBE501001 General Description PJ-722/PJ-723 PJ-762/PJ-763/PJ-763MFi PJ-773                Button Functions Installing the Rechargeable Li-ion Battery 1.Move battery latch 1 to the unlock position. 2.While holding battery latch 2 in the unlock position, remove the battery cavity mounting block. 3.Release battery latch 2. Battery latch 2 moves back to the lock position. 4.Insert the battery into the battery cavity until it locks into place. 5.Move battery latch 1 to the lock position. Removing the Rechargeable Li-ion Battery 1.Move the battery latches to the unlock position, and then remove the battery. 2.Insert the battery cavity mounting block into the battery cavity until it locks into place. 3.Move battery latch 1 to the lock position. Charging the Rechargeable Li-ion Battery 1.Turn the printer off and install the battery. 2.Use the AC adapter and AC power cord to connect the printer to an AC power outlet, or use the car adapter to connect the printer to a DC power outlet. 3.When the battery is fully charged, the STATUS indicator turns off. Disconnect the AC adapter or car adapter from the DC connector. Stopping Rechargeable Li-ion Battery Charging To stop the battery charging, disconnect the AC adapter or car adapter from the DC connector. (Power) button function Operation Turn the printer onPress and hold the button for about one second until the POWER indicator turns on. Turn the printer offPress and hold the button for about one second or press it quickly two times depending on the printer setting (see the Online User’s Guide for more information). (Feed) button function Operation Feed paperLoad the paper and press the button to feed the paper. Print the printer settingsTo print the printer settings without connecting the printer to a computer or mobile device: 1Turn the printer on and make sure no paper is loaded. 2Press and hold the button until the DATA indicator lights in red. 3Load paper. (Bluetooth) button function (PJ-762/PJ-763/PJ-763MFi only) Operation Enable/disable the Bluetooth function Press and hold the button for one second to enable or disable the Bluetooth function of the printer. (Wi-Fi) button function (PJ-773 only) Operation Enable/disable the Wi-Fi function Press and hold the button for one second to enable or disable the Wi-Fi function of the printer. Use WPS to configure Wi-Fi settings easily Press and hold the button for about five seconds to configure the Wi-Fi settings using WPS. Use the Rechargeable Li-ion Battery (Optional) 1Battery latch 1 2Battery latch 2 3Battery cavity mounting block 4Battery cavity 5Rechargeable Li-ion battery 2 3 1 4 5 1Battery latches NOTE • Charge the battery immediately after purchase using the following procedure. • Up to three hours are needed to fully charge the rechargeable Li-ion battery. When fully charged, the battery will print about 300 pages. 1POWER indicator 2STATUS indicator Notes on Using the Rechargeable Li-ion Battery „Fully charge the battery before use. Do not use it before it is fully charged. „High density (dark) printing discharges the battery faster than low density printing. Adjust the print density setting in the printer driver’s dialog box or Printer Setting Tool (see the Online User’s Guide). „The battery charging must take place in 32°F - 104°F (0°C - 40°C) environments, otherwise the battery will not be charged, and the STATUS indicator will remain lit. „If you use the printer when both the battery is installed and the AC adapter or car adapter is connected, the STATUS indicator may turn off and charging may stop eve…

Text truncated - open the document above for the full version.

BROTHER INDUSTRIES, LTD. 15-1 . Naeshiro-cho. Mizuho-ku, Nagoya 467-8561, Japan Phone : +81 528242348 Fax '. +81 52 821 1068 Letter of Authorization Date: June 5.2015 UL Japan, Inc. 4383 -326 Asama-cho. Ise-shi" Mie 516-0021 Japan FCC ID : B3Q8V9313 Applicant: Brother Industries, Ltd. To whom it may concern: Please be advised we authorize Yoshihisa Maeda of Consumer Technology Division, UL Japan, Inc. to act on our behalf, until otherwise notified, for applications submitted for Federal Communication Commission Radio equipment applications submitted to UL Japan, Inc. We certiff that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial offederal benefits, that includes FCC benefits. The application for the subject equipment has not been submitted to another TCB for certification. Thank you for your attention to this matter. Sincerely, BROTHER INDUSTRIES. LTD.

BROTHER INDUSTRIES. LTD. 15-1 , Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan Phone : +81 528242348 Fax : +81 52 821 1068 Request for Confidentiality Date: June 5.2015 UL Japan, Inc. 4383 -326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID : B3Q8V93l3 Applicant : Brother Industries, Ltd. To whom it may concern: Please be advised that the following information is to be held confidential on behalf of us, referring to the FCC rules 0.457 and 0.459: Block Diagram Theory of Operation Schematics Parts List The application contains technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, BROTHER INDUSTzuES. LTD.

Date: June 5,2015 UL Japan, Inc. 4383 -326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID : 83Q8V9313 Applicant: Brother Industries, Ltd. To whom it may concem: Please be advised that the following information is to be held in confidence for 120 days from the date of the Grant of Equipment Authorization and behalf of us, referring to the FCC rules 0.457 and 0.459: External Photos Internal Photos Test Setup Photos User Manual The application contains technical information, which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely,

External Photo BROTHER INDUSTRIES LTD. Mobile Printer[Model: PJ-773] Top Bottom (with battery) External Photo BROTHER INDUSTRIES LTD. Mobile Printer[Model: PJ-773] Front Back External Photo BROTHER INDUSTRIES LTD. Mobile Printer[Model: PJ-773] Side (Right) Side (Left)

Takaaki Oguchi DD14-0555 Apr. 13, 2015 Ryohei Murabayashi PJ-773

Internal Photo BROTHER INDUSTRIES LTD. Mobile Printer[Model: PJ-773] Bottom (without battery) Bottom (uncovering) Internal Photo BROTHER INDUSTRIES LTD. Mobile Printer[Model: PJ-773] Bottom (uncovering 2) WIFI module (T77H505) WIFI module (T77H505) Internal Photo BROTHER INDUSTRIES LTD. Mobile Printer[Model: PJ-773] Main PCB and Metal Frame 1 Main PCB and Metal Frame 2 Internal Photo BROTHER INDUSTRIES LTD. Mobile Printer[Model: PJ-773] Main PCB Top Main PCB Bottom Internal Photo BROTHER INDUSTRIES LTD. Mobile Printer[Model: PJ-773] WIFI module FPC FPC

Test report No. : 10733022H-C Page : 1 of 57 FCC ID : B3Q8V9313 Issued date : June 22, 2015 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8999 Facsimile: +81 596 24 8124 13-EM-F0429 SAR TEST REPORT Test Report No. : 10733022H-C Applicant :Brother Industries, Ltd. Type of Equipment :Mobile Printer Model No. :PJ-773 FCC ID :B3Q8V9313 Test regulation : FCC47CFR 2.1093 Test Result : Complied Reported SAR(1g) Value The highest reported SAR(1g) Body : 0.437W/kg 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. The test results in this report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 6. This test report covers SAR technical requirements. It does not cover administrative issues such as Manual or non-SAR test related Requirements. (if applicable) Date of test: June 4, 2015 Representative test engineer: Hisayoshi Sato Engineer Consumer Technology Division Approved by : Takahiro Hatakeda Leader Consumer Technology Division NVLAP LAB CODE: 200572-0 This laboratory is accredited by the NVLAP LAB CODE 200572-0, U.S.A. The tests reported herein have been performed in accordance with its terms of accreditation. *As for the range of Accreditation in NVLAP, you may refer to the WEB address, http://www.ul.com/japan/jpn/pages/services/emc/about/m ark1/index.jsp#nvlap Test report No. : 10733022H-C Page : 2 of 57 FCC ID : B3Q8V9313 Issue date : June 22, 2015 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8999 Facsimile: +81 596 24 8124 REVISION HISTORY Original Test Report No.: 10733022H-C Revision Test report No. Date Page revised Contents - (Original) 10733022H-C June 22, 2015 - - Test report No. : 10733022H-C Page : 3 of 57 FCC ID : B3Q8V9313 Issue date : June 22, 2015 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8999 Facsimile: +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information .................................................................................................... 4 SECTION 2: Equipment under test (E.U.T.) ...................................................................................... 4 2.1 Identification of E.U.T. ....................................................................................................................................... 4 2.2 Product Description ............................................................................................................................................ 4 SECTION 3 : Test standard information ............................................................................................ 5 3.1 Test Specification ............................................................................................................................................... 5 3.2 Procedure ............................................................................................................................................................ 5 3.3 Exposure limit .................................................................................................................................................... 6 3.4 Test Location ...................................................................................................................................................... 6 SECTION 4 : Test result ....................................................................................................................... 7 4.1 Stand-alone SAR result....................................................................................................................................... 7 SECTION 5 : Description of the operating mode ............................................................................... 8 5.1 Output power operating modes ........................................................................................................................... 8 5.2 Output power measurement results ..................................................................................................................... 8 5.3 SAR testing operating modes ............................................................................................................................. 9 5.4 Confirmation after SAR testing .......................................................................................................................... 10 SECTION 6 SAR test exclusion considerations .................................................................................. 11 6.1 Standalone SAR test exclusion considerations according to KDB447498 D01 ................................................. 11 SECTION 7: Description of the Body setup ........................................................................................ 13 7.1 Test position for Body setup ............................................................................................................................... 13 SECTION 8 : Test surrounding ........................................................................................................... 14 8.1 Measurement uncertainty ................................................................................................................................... 14 SECTION 9 : Measurement results ..................................................................................................... 15 9.1 Body SAR ......................................................................................................................................................... 15 SECTION 10 Test …

Text truncated - open the document above for the full version.

Test report No. : 10733022H-A ― Page : 1 of 43 Issued date : June 12, 2015 FCC ID : B3Q8V9313 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 13-EM-F0429 RADIO TEST REPORT Test Report No. : 10733022H-A Applicant : Brother Industries, Ltd. Type of Equipment : Mobile Printer Model No. : PJ-773 FCC ID : B3Q8V9313 Test regulation: FCC Part 15 Subpart C: 2015 Test Result : Complied 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the above regulation. 4. The test results in this report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 6. This test report covers Radio technical requirements. It does not cover administrative issues such as Manual or non-Radio test related Requirements. (if applicable) Date of test: May 20 to June 3, 2015 Representative test engineer: Shinichi Miyazono Engineer Consumer Technology Division Approved by: Takahiro Hatakeda Leader Consumer Technology Division NVLAP LAB CODE: 200572-0 This laboratory is accredited by the NVLAP LAB CODE 200572-0, U.S.A. The tests reported herein have been performed in accordance with its terms of accreditation. *As for the range of Accreditation in NVLAP, you may refer to the WEB address, http://www.ul.com/japan/jpn/pages/services/emc/about/ma rk1/index.jsp#nvlap Test report No. : 10733022H-A Page : 2 of 43 Issued date : June 12, 2015 FCC ID : B3Q8V9313 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 REVISION HISTORY Original Test Report No.: 10733022H-A Revision Test report No. Date Page revised Contents - (Original) 10733022H-A June 12, 2015 - - Test report No. : 10733022H-A Page : 3 of 43 Issued date : June 12, 2015 FCC ID : B3Q8V9313 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ....................................................................................................... 4 SECTION 2: Equipment under test (E.U.T.) ......................................................................................... 4 SECTION 3: Test specification, procedures & results .......................................................................... 5 SECTION 4: Operation of E.U.T. during testing .................................................................................. 8 SECTION 5: Conducted Emission ........................................................................................................ 10 SECTION 6: Radiated Spurious Emission .......................................................................................... 11 SECTION 7: Antenna Terminal Conducted Tests .............................................................................. 12 APPENDIX 1: Test data ........................................................................................................................ 13 Conducted Emission ......................................................................................................................... 13 6dB Bandwidth ................................................................................................................................. 14 Maximum Peak Output Power .......................................................................................................... 17 Average Output Power ...................................................................................................................... 19 Burst rate confirmation ..................................................................................................................... 22 Radiated Spurious Emission ............................................................................................................. 23 Band Edge confirmation ................................................................................................................... 32 Conducted Spurious Emission .......................................................................................................... 34 Power Density ................................................................................................................................... 35 99%Occupied Bandwidth ................................................................................................................. 38 APPENDIX 2: Test instruments ........................................................................................................... 40 APPENDIX 3: Photographs of test setup ............................................................................................. 41 Conducted Emission ......................................................................................................................... 41 Radiated Spurious Emission ............................................................................................................. 42 Worst Case Position .......................................................................................................................... 43 Test report No. : 10733022H-A Page : 4 of 43 Issued date : June 12, 2015 FCC ID : B3Q8V9313 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 SECTION 1: Customer information Company Name : Brother Industries, Ltd. Address : 15-1, Naeshiro-cho, Mizuho-ku, Nagoya, 467-8561, Japan Telephone Number : +81-52-824-2345 Facsimile Number : +81-52-821-1068 Contact Person : Shintaro Uno SECTION 2: Equipment under test (E.U.T.) 2.1 I…

Text truncated - open the document above for the full version.

Test report No. : 10733022H-C Page : 54 of 57 FCC ID : B3Q8V9313 Issue date : June 22, 2015 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8999 Facsimile: +81 596 24 8124 APPENDIX 4: Photographs of test setup 1. Photographs of EUT Top Bottom Front Rear Left Right Test report No. : 10733022H-C Page : 55 of 57 FCC ID : B3Q8V9313 Issue date : June 22, 2015 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8999 Facsimile: +81 596 24 8124 2. Antenna position [Front side view] [Left side view] Top Bottom Front Rear Left Right Top Bottom Antenna Test report No. : 10733022H-C Page : 56 of 57 FCC ID : B3Q8V9313 Issue date : June 22, 2015 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8999 Facsimile: +81 596 24 8124 3. Photographs of setup Front Rear Left Top Test report No. : 10733022H-C Page : 57 of 57 FCC ID : B3Q8V9313 Issue date : June 22, 2015 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8999 Facsimile: +81 596 24 8124 Bottom End of Report

Test report No. : 10733022H-A Page : 41 of 43 Issued date : June 12, 2015 FCC ID : B3Q8V9313 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 APPENDIX 3: Photographs of test setup Conducted Emission Photo 1 Photo 2 Test report No. : 10733022H-A Page : 42 of 43 Issued date : June 12, 2015 FCC ID : B3Q8V9313 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Radiated Spurious Emission Photo 1 Photo 2 Test report No. : 10733022H-A Page : 43 of 43 Issued date : June 12, 2015 FCC ID : B3Q8V9313 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Worst Case Position (Horizontal: X-axis/ Vertical:Y-axis) (Above 1GHz) (Horizontal: Z-axis/ Vertical:Y-axis) (Below 1GHz) X-axis Y-axis Z-axis End of Report